SEARCH · Search NASA

Results for “Thermal materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Frequency-domain hot-wire sensor and 3D model for thermal conductivity measurements of reactive and corrosive materials at high temperatures

High temperature solids and liquids are becoming increasingly important in next-generation energy and manufacturing systems that seek higher efficiencies and lower emissions. Accurate measurements of thermal conductivity at high temperatures are required for the modeling and design of these systems, but commonly employed time-domain measurements can have errors from convection, corrosion, and ambient temperature fluctuations. Here, we describe the development of a frequency-domain hot-wire technique capable of accurately measuring the thermal conductivity of solid and molten compounds from room temperature up to 800 °C. Therefore, by operating in the frequency-domain, we can lock into the harmonic thermal response of the material and reject the influence of ambient temperature fluctuations, and we can keep the probed volume below 1 µl to minimize convection. The design of the microfabricated hot-wire sensor, electrical systems, and insulating wire coating to protect against corrosion is covered in detail. Furthermore, we discuss the development of a full three-dimensional multilayer thermal model that accounts for both radial conduction into the sample and axial conduction along the wire and the effect of wire coatings. The 3D, multilayer model facilitates the measurement of small sample volumes important for material development. A sensitivity analysis and an error propagation calculation of the frequency-domain thermal model are performed to demonstrate what factors are most important for thermal conductivity measurements. Finally, we show thermal conductivity measurements including model data fitting on gas (argon), solid (sulfur), and molten substances over a range of temperatures.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Automated Parameterized CFD Simulations of Phase-Change Material Embedded Heat Exchangers

Thermal storage can be implemented using Phase-Change Materials (PCM), which absorb significant latent heat with a relatively small temperature change. PCM phase-change processes are transient and are driven by thermal diffusion and natural convection – the latter, especially for melting process. Modeling and simulation of PCM heat exchangers is typically computationally intensive due to the relative complex time-dependent underlying physics. This paper presents a study investigating a single straight tube with circular transverse fins in the vertical orientation, using PCM’s with 37oC nominal melting temperature, leveraging automated parametric CFD simulations. The computational domain is reduced to 2D axisymmetric for a segment of the HX comprising a region in between two fins with constant wall temperature as boundary condition. This approach allows for faster evaluations of the transient thermal characteristics for a given design space of interest. Correlations and reduced order models (ROM’s) are developed. Results indicate that the ROM’s reproduce the CFD simulations with high accuracy for designs from the training data set, however, designs from cross-validation and test sets do not always have good agreement. The limited number of designs in the training set is a possible cause for the lack of robustness of the ROM’s and thus additional training designs will be added in future work. The ROM’s solve the simulations on average 500,000 times faster than CFD.

25 ENERGY STORAGE↗

DOE OSTI2023

Topology optimization of compliant mechanisms under transient thermal conditions

This work considers multi-material topology optimization of compliant mechanisms under transient thermal and quasi-static mechanical conditions wherein thermally actuated devices are optimized for different operating conditions. The materials are modeled using finite strain thermo-hyperelasticity and a two way coupling between the energy balance and equilibrium equations is investigated. The design updates are generated from the gradient-based method of moving asymptotes optimizer and the sensitivities are computed using the time dependent adjoint sensitivity analysis. Results show the impact of designing for short versus long actuation times.

42 ENGINEERING↗

DOE OSTI2023

High temperature thermochemical energy storage materials

Disclosed are thermal energy storage systems and methods that utilize metal carbonate eutectics that can undergo high temperature reversible reactions to form mixtures of metal oxides. The metal oxides undergo an exothermic reaction with carbon dioxide to form the molten metal carbonate eutectics, and the molten metal carbonate eutectics undergo an endothermic decarbonization reaction to form the metal oxides and carbon dioxide. By carrying out the reversible reactions at a temperature above the melting point of the carbonate eutectic, the systems provide high thermal conductivity and reversible stability for thermal energy storage.

25 ENERGY STORAGE↗

DOE OSTI2025

Time-domain thermoreflectance

Time-domain thermoreflectance (TDTR) has been instrumental in measuring the heat transfer properties of bulk and nanostructured materials over the past two decades. In this Primer, we describe the optical and thermal aspects of TDTR, with an in-depth discussion on the theory, apparatus design and implementation. We present examples that illustrate the ability of TDTR to measure thermal conductivity tensors, thermal conductance across material interfaces, and volumetric heat capacity of thin films, 2D materials and bulk materials. The ability of TDTR to spatially resolve thermal properties is useful for studying heterogeneous material systems, such as materials processed in or subjected to extreme environments. We consider current limitations of pump–probe metrologies and discuss recent advancements of TDTR, such as time-resolved magneto-optic Kerr effect (TR-MOKE), beam-offset TDTR/TR-MOKE, steady-state thermoreflectance, frequency-domain thermoreflectance and laser-flash TDTR. Lastly, we present an outlook on anticipated technological developments to further expand the ability of TDTR to measure nanoscale thermal properties.

42 ENGINEERING↗

DOE OSTI2021

Thermal Conductivity Measurement of Microstructure in Irradiated Materials

Argonne National Laboratory is establishing additional capabilities for advanced techniques for accelerated experiment-based fuel material screening. A key supporting element is expanded capabilities for the characterization of irradiated samples, including establishment of the capability to measure irradiated fuel thermal conductivity at the micro-scale level. Argonne is collaborating with the University of Illinois at Urbana-Champaign (UIUC) to adopt the suspended bridge method to measure thermal conductivity of radiation-induced microstructures in nuclear materials directly. The initial phase of work to support thermal conductivity measurements of microstructure in irradiated materials at Argonne has been executed, and is summarized here. This report is intended to serve as a status update for this activity, summarizing work completed in FY20.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Medium-temperature phase change material integration in domestic heat pump water heaters for improved thermal energy storage

In this review, we examine state-of-the-art developments in integrating phase change materials (PCMs) for thermal energy storage (TES) in domestic heat pump water heaters (HPWHs). The component design optimization and control optimization of HPWHs and TES are reviewed for insight into improving the thermal capacity and efficiency of a PCM-integrated HPWH. The state-of-the-art review is categorized by the stage of development of the PCM for deployment in HPWHs. To select appropriate PCMs for HPWHs, a six-factor down-selection process is used to determine the best material(s) for integration in HPWHs with appropriate heat exchanger design. Ultimately, food-grade PCMs appear to be the best candidate for integration of TES in domestic HPWHs because they are nontoxic, highly cyclable, and have heat transfer properties accommodable to water heating when integrated in a manner to overcome the thermal conductivity limitations of the material. A key parameter of water heating performance is thermal heating power of the PCM component, which is not often reported. Many studies report significant improvement in capacity and efficiency. Furthermore, many performance metrics are identified from the literature to quantify the system performance, but agreement across studies is not found. Unified energy factor and first hour rating performance tests are required for commercially available HPWHs, and these performance metrics could homogenize the literature. Ultimately, we find that select PCMs are ready for deployment with HPWHs for performance improvement, and component design and control optimizations are new avenues of research and development required for a commercially viable PCM-integrated HPWH system.

25 ENERGY STORAGE↗

DOE OSTI2020

Heat dissipation assembly

A heat dissipating assembly including a layered stack of materials with a highly thermally conductive path for cooling a circuit, the stack including a structurally isolated material having a high coefficient of thermal expansion connected between materials having low coefficients of thermal expansion.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Compressed Expanded Natural Graphite (CENG) Processing for PCM Composites

The use of phase change materials (PCMs) in thermal energy storage applications has received considerable attention in recent decades. Organic PCMs are popular due to their high latent heat of fusion, noncorrosive properties, and relative stability over many charge and discharge cycles. A primary limitation of these materials is their low thermal conductivity. This has led researchers to develop various methods to increase thermal conductivity by seeding PCM with or impregnating them into more conductive materials. One method is to impregnate PCMs into compressed expanded natural graphite (CENG) matrices, which can improve thermal conductivity by a factor of 100. CENG matrices have received particular interest due to their low cost, high porosity, small (nano/micro) pore size, high pore density, high thermal conductivity, and ability to be compressed into many geometries. PCM/CENG matrix composites have been extensively studied; however, the effect that CENG processing has on PCM saturation and the overall matrix thermal conductivity has not been well investigated. This processing includes four major steps including graphite intercalation, thermal shock, compression, and PCM saturation. Intercalation involves soaking graphite flakes in sulfuric and/or nitric acid to intercalate the acids between the graphene layers. The graphite flakes are then subjected to a high-temperature thermal shock, during which the intercalated acid is gasified rapidly, pushing the graphene layers apart, resulting in accordion-shaped graphite "worms". The "worms" are then compacted to a desired bulk density and then soaked with molten PCM until fully saturated. The properties of the produced CENG matrix, and its ability to allow PCM permeation, are sensitive to the processing parameters, namely, the thermal shock temperature and exposure time, as well as the matrix apparent density or porosity. Here, we study the effect of the thermal shock conditions necessary to expand intercalated graphite flakes on PCM saturation and the expanded graphite's thermal conductivity and morphology. We found that the thermal shock temperature exhibits the greatest influence. At greater shock temperatures, SEM images showed that expanded graphite worms exhibited greater density of pores, thus increasing total surface area within the matrices. Increasing thermal shock temperature yielded greater overall PCM saturation, as well as an increased rate of saturation. Improvements in PCM saturation rate and overall saturation are obtained as the shock temperature is increased. Longer exposure to thermal shock also improves initial saturation rates and is beneficial if a shortened impregnation time is needed. Thermal shock conditions did not impact thermal conductivity; however, conductivity was largely affected by matrix porosity. A local maximum in axial thermal conductivity was observed at around 83% porosity, which is similar to that observed in previous studies.

compressed expanded natural graphite↗

DOE OSTI2022

PCM Selection for Heat Pump Integrated with Thermal Energy Storage for Demand Response in Residential Buildings

Phase Change Materials (PCM) based Thermal energy storage (TES) is a widespread solution to shift buildings’ peak energy demand and add stability to the grid. PCMs can be used for space heating and cooling applications in residential buildings by integrating into the heat pump equipment or building envelope via several possible configurations. The heat pump integrated active PCM storage can provide significant energy savings and reduce peak demand, but the benefits vary substantially depending on the system configuration, storage capacity, and the temperature range of the PCM used. It is critical to provide a review of the materials and their suitability in heat pump integrated PCM systems. This paper will present an analysis of the PCM material selection for heat pump integrated TES in various configurations. The comprehensive review will compare the phase change materials with different melting temperatures, and configurations, corresponding to the energy savings and demand impact reported in the literature. This work is significant to guide the design of high-performance heat pump integrated PCM systems.

Sultan, Sara↗

DOE OSTI2023

Ferroelectric Domain Wall Engineering Enables Thermal Modulation in PMN–PT Single Crystals

Acting like thermal resistances, ferroelectric domain walls can be manipulated to realize dynamic modulation of thermal conductivity ( k ), which is essential for developing novel phononic circuits. Despite the interest, little attention has been paid to achieving room-temperature thermal modulation in bulk materials due to challenges in obtaining a high thermal conductivity switching ratio ( k high / k low ), particularly in commercially viable materials. Here, room-temperature thermal modulation in 2.5 mm-thick Pb(Mg 1/3 Nb 2/3 )O 3 – x PbTiO 3 (PMN– x PT) single crystals is demonstrated. With the use of advanced poling conditions, assisted by the systematic study on composition and orientation dependence of PMN– x PT, a range of thermal conductivity switching ratios with a maximum of ≈1.27 is observed. Further, simultaneous measurements of piezoelectric coefficient (d 33 ) to characterize the poling state, domain wall density using polarized light microscopy (PLM), and birefringence change using quantitative PLM reveal that compared to the unpoled state, the domain wall density at intermediate poling states (0< d 33 33,max ) is lower due to the enlargement in domain size. At optimized poling conditions (d 33,max ), the domain sizes show increased inhomogeneity that leads to enhancement in the domain wall density. This work highlights the potential of commercially available PMN– x PT single crystals among other relaxor-ferroelectrics for achieving temperature control in solid-state devices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Crystal structure solution and high-temperature thermal expansion in NaZr 2 (PO 4 ) 3 -type materials

The NaZr 2 P 3 O 12 family of materials have shown low and tailorable thermal expansion properties. In this study, SrZr 4 P 6 O 24 (SrO·4ZrO 2 ·3P 2 O 5 ), CaZr 4 P 6 O 24 (CaO·4ZrO 2 ·3P 2 O 5 ), MgZr 4 P 6 O 24 (MgO·4ZrO 2 ·3P 2 O 5 ), NaTi 2 P 3 O 12 [½(Na 2 O·4TiO 2 ·3P 2 O 5 )], NaZr 2 P 3 O 12 [½(Na 2 O·4ZrO 2 ·3P 2 O 5 )], and related solid solutions were synthesized using the organic–inorganic steric entrapment method. The samples were characterized by in-situ high-temperature X-ray diffraction from 25 to 1500°C at the Advanced Photon Source and National Synchrotron Light Source II. The average linear thermal expansion of SrZr 4 P 6 O 24 and CaZr 4 P 6 O 24 was between −1 × 10 −6 per °C and 6 × 10 −6 per °C from 25 to 1500°C. The crystal structures of the high-temperature polymorphs of CaZr 4 P 6 O 24 and SrZr 4 P 6 O 24 with R 3 c symmetry were solved by Fourier difference mapping and Rietveld refinement. This polymorph is present above ∼1250°C. This work measured thermal expansion coefficients to 1500°C for all samples and investigated the differences in thermal expansion mechanisms between polymorphs and between compositions.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Influence of Phase-Change Materials and Operating Periods on Load Shifting for Thermal Storage Heat Pumps in European Climate Zones

As the reliance on heat pumps (HPs) for space conditioning increases worldwide, ex-tensive grid strains during utility peak hours are expected. Significant research efforts focus on investigating the use of integrated thermal energy storage (TES) systems to reduce peak energy demands. Conventionally, TES systems are often integrated to store and provide either cooling or heating, but not both. In this work, a single room-temperature phase-change material (PCM)-TES was integrated for dual-mode opera-tion with an R290 air-to-water 10.5 kW (3-Ton) HP. Two PCM melting temperatures (17°C, 22°C) were assessed to investigate their impact on system performance and cost reductions for Milan, Italy (4A); Barcelona, Spain (3A); and Oslo, Norway (6A). HP and HP-TES performance maps were generated using Modelica-based transient models and co-simulated with a prototype residential building using the Spawn of En-ergyPlusTM with simple rule-based controls. Our simulations indicate that PCM-17°C provided annual cost savings at higher peak-to-off-peak cost ratios, as the demand re-duction dominated the savings potential. The recharge energy costs and requirements became more dominant at lower cost ratios, making PCM-22°C more beneficial at lower cost ratios. Finally, despite Oslo's heating-dominated climate, the utility peak hours favor cooling demand reductions, making PCM-17°C more appealing. In all cases, the cost savings potential stabilized between 4 – 10% regardless of cost ratio, suggesting that system-level component and operation control optimization is required to maximize cost savings further.

25 ENERGY STORAGE↗

DOE OSTI2021

Method for tuning thermal expansion properties in an additive manufacturing feedstock material

A feedstock material for use in an additive manufacturing apparatus is prepared from a first material and a metal organic framework (MOF). The MOF comprises a plurality of nodes and a plurality of linkers, the plurality of linkers coupled to the plurality of nodes, thereby forming a framework. The MOF has a lower coefficient of thermal expansion than a coefficient of thermal expansion for the first material. As a result, the feedstock material has a reduced coefficient of thermal expansion as compared to the first material alone and thus exhibits low thermal expansion as its temperature is increased. The coefficient of thermal expansion for the MOF may be modified by using a different plurality of nodes and/or a different plurality of linkers, as well as by incorporating guest molecules or atoms into the framework of the MOF.

Burtch, Nicholas C.↗

DOE OSTI2025

Passive radiative thermal management using phase-change metasurfaces

Abstract Realizing innovative composite materials with passive thermal management capabilities and minimal ecological footprints is a challenging but much sought-after goal that would have a transformative effect on renewable energy sciences. We demonstrate an environmentally friendly metasurface utilizing vanadium dioxide (VO 2 ) that offers responsiveness to ambient temperature and potentially long-term stability. The metasurface enables passive thermal management by self-adjusting its absorptivity and emissivity response over a broad bandwidth ranging from visible to mid-infrared (IR) wavelengths. Above the VO 2 phase transition the metasurface exhibits increased mid-IR emissivity and reduced visible/near-IR absorptivity, creating an efficient radiative emission channel in the first atmospheric transparency window with reduced absorption of solar radiation. In contrast, below VO 2 ’s transition temperature, the metasurface increasingly absorbs sun light while minimizing mid-IR radiative heat losses. Moreover, a functional silicon layer eliminates the need for an additional capping layer commonly employed to protect VO 2 from environmental degradation. The additional protective layer often impedes the use and performance of VO 2 based devices in terrestrial as well as spacecraft applications. Therefore, the proposed durable and eco-friendly metasurface will be an excellent candidate for essential passive thermal regulation systems across residential and terrestrial applications.

42 ENGINEERING↗

DOE OSTI2024

Impact of Cooling Rate and Thermal Mass on Supercooling in a Salt-Hydrogel Complex for Thermal Energy Storage

Glauber’s salt is a promising phase change material for building thermal management because of its high latent heat, acceptable melting temperature of 32.3 °C for indoor air1,2. Despite these advantages, the practical application of Glauber’s salt in thermal energy storage systems is still challenging due to supercooling and phase segregation1–3. Here, we report the impact of temperature ramp rate and thermal mass on the supercooling of Glauber’s salt through the DSC and T-history experiment. The ramp rate effect was studied with a wide range of ramp rates in 1 to 10 °C/min in DSC and 1 to 4 °C/min in the T-history experiment. The thermal mass effect was investigated by comparing DSC and T-history experiment. The latent heat was also analyzed for different ramp rates and thermal mass conditions. The melting temperatures of Glauber’s salt from the two techniques were identical while freezing temperatures were different because of the thermal mass effect. During freezing in the T-history experiment, the latent heat was reduced by around 75% to the latent heat in melting due to supercooling and phase segregation. To overcome this bottleneck, we developed a novel hydrogel complex that reduces the supercooling and prevents phase segregation to maintain volumetric energy density for 100 cycles. Thermodynamic analysis accounting for composition shows that a higher salt composition can further enhance the volumetric energy storage density. For example, a 10% increase in the weight percentage of salt leads to about 50% enhancement in volumetric energy storage density. References: 1. D. R. Biswas, Solar Energy. 19, 99–100 (1977). 2. S. M. Hasnain, Energy Conversion and Management. 39, 1127–1138 (1998). 3. Byung Chul Shin, Sang Done Kim, P. Won-Hoon, Energy. 14, 921–930 (1989).

inorganic, thermodynamics↗

DOE OSTI2023

Low-temperature oxidation pathways are critical to thermal incineration of PFAS-laden materials

With growing desire to destroy per- and poly-fluoroalkyl substances (PFAS) now known to be detrimental to human health, a sound understanding of fluorocarbon combustion chemistry is important to efficient thermal destruction within incinerators. While most fluorocarbon combustion models and the sets of reactions contained within them were originally developed for the high temperatures encountered in flame suppression applications, they have often been used to assess PFAS destruction in incinerators, which emphasize a lower range of temperatures. We present results that demonstrate that low-temperature fluorocarbon oxidation pathways—not yet known to play a role in fluorocarbon combustion—impact key incinerator performance metrics, including: PFAS surrogate mole fractions, products of incomplete destruction, and waste destruction efficiencies. The results further point to the utility of NO as a potential additive. The present results show the influence of these pathways for CF 3 O 2 , for which some data are available, but analogous pathways would also occur for other fluoroalkylperoxy radicals, for which little is known. Furthermore, the results demonstrate the need for future work to identify and characterize low-temperature pathways more generally, consider such pathways in kinetic model development, and experimentally probe intermediate temperature conditions to better understand, design, and control thermal destruction technologies for improved PFAS management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Temperature Rise on Liner Surfaces of Fuel Cell Electric Vehicle Tanks during Fueling Process

Herein, the temperature of the inner tank walls, or plastic liners, of composite pressure tanks in fuel cell electric vehicles during fueling using three‐dimensional computational fluid dynamics (CFD) models is evaluated. The liner materials are limited to 85.0 °C to prevent thermal stress causing material failure that would result in a hydrogen leak. Therefore, the temperature of hydrogen gas must be limited to below 85.0 °C during the fueling process as dictated by the current fueling protocol. However, there are limited experimental or simulation data confirming that the temperature changes do not exceed the threshold. Herein, the liner temperatures with CFD tank models for two sizes of type IV tanks representative of the upper and lower system bounds that are close to the SAE J2601 fueling protocol (36.0 and 244.0 L) are evaluated. First, each model's reliability is validated with experimental data and then analyzed, and the data are used to evaluate the maximum hydrogen and liner temperatures under real‐world fueling conditions. The evaluation shows that the maximum liner surface temperature of each tank model is at least 7 °C lower than that of the hydrogen. Additionally, there is at least 12 °C difference found between the upper limit and actual liner temperatures.

33 ADVANCED PROPULSION SYSTEMS↗