Inviscid hypersonic flow past blunt bodies.
Inviscid hypersonic flow of uniform equilibrium gas past axisymmetric blunt body
Chou, Y.-S.↗
SEARCH · Search NASA
Results for “UNIFORM FLOW”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of mass addition of various gases on the heat transfer and surface pressures on a blunt cone in hypersonic flow.
Surface pressure and heat transfer over blunt conical body in hypersonic flow with uniform mass addition of various gases
Lee, G.↗
Theoretical Study of Ducted Fan Performance
Existing computer program improved capability for predicting performance of ducted fan in uniform axial flow
Mendenhall, M. R.↗
Heat transfer and pressure on a hypersonic blunt cone with mass addition
Surface pressure and heat transfer over blunt conical body in hypersonic flow with uniform mass addition of various gases
Lee, G.↗
Liquid-phase mixing of bipropellant doublets
Experimental results of unlike doublet mixing are correlated with an analytically derived equation predicting fluid cavitation. The correlation relates the minimum orifice pressure drop required to initiate cavitation, with the system back pressure, cold flow simulant vapor pressure, and the orifice flow discharge and contraction coefficients. Stream flow instabilities are also visually correlated with the onset of cavitation and orifice discharge coefficient measurements. The influence of cavitation on the characteristic phenomenon of hydraulic flip is observed for both circular and noncircular shaped orifices. For certain intermediate orifice lengths, some noncircular shapes are shown to produce more fully developed flows (shorter recovery lengths) and therefore a more cohesive jet, which in turn yields slightly higher cold flow mixing uniformities than circular shaped orifices of equal absolute length. The particular noncircular shaped elements evaluated are shown to be more sensitive to liquid stream misimpingement than the corresponding circular orifices.
Hoehn, F. W.↗
High-loading low-speed fan study. 4: Data and performance with redesign stator and including a rotor tip casing treatment
A single stage fan with a rotor tip speed of 1000 ft/sec(304.8 m/sec) and a hub-to-tip ratio of 0.392 was retested with a redesigned stator. Tests were conducted with uniform inlet, tip-radial, hub-radial, and circumferential inlet distortions. With uniform inlet flow, stall margin was improved 12 percentage points above that with the original stator. The fan demonstrated an efficiency of 0.883 and a stall margin of 15 percent at a pressure ratio of 1.488 and a specific flow of 41.17 lb/sec/sq ft. Tests were also made with a redesigned casing treatment consisting of skewed slots over the rotor blade tips. This casing treatment gave a 7 percentage point improvement in stall margin when tested with tip radial distortion (when the rotor tip initiated stall). Noise measurements at the fan inlet and exit indicate no effect from closing the stator 10 degrees, nor were there measurable effects from adding skewed slots over the blade tips.
Harley, K. G.↗
Preliminary results of large supersonic burning combustor testing.
A hydrogen fueled supersonic-burning combustor 18 in. in diameter, which is equivalent to that of an engine about 6 ft in diameter, was tested as a direct-connected duct at inlet conditions which simulated Mach 8 flight at 115,000 ft alt. A synthetic air consisting of oxygen with 39% nitrogen and 38% water vapor at a total temperature of 4500 deg R and a total pressure of 300 psia was supplied to the combustor inlet by a hydrazine-nitrogen tetroxide hot gas generator which maintained a uniform inlet flow Mach number of 2.8. The large combustor size required a new approach to fuel injector design. Some hydrogen was injected through flush-wall injectors, but most was injected from two rows of swept and tapered struts immersed in the flow stream. Supersonic combustion was obtained at hydrogen equivalence ratios of 0.94 without encountering thermal cho king. Wall static pressures, and the radial distribution of hydrogen, Pitot pressure, and Mach number were determined at the combustor exit.
Metzler, A. J.↗
Acoustic propagation in ducts with varying cross sections and sheared mean flow.
An analysis is presented of the wave propagation and attenuation in two-dimensional ducts with slowly varying cross sections which carry sheared mean flow. A uniformly valid asymptotic expansion of the acoustic waves is obtained in terms of the maximum slope of the wall by using the method of multiple scales. The result is a first-order differential equation describing the amplitude variation with the axial distance. This equation is used to evaluate the effects of variations of the duct cross section and growing boundary layers on the different acoustic modes.
Nayfeh, A. H.↗
Effect of gravitational and aerodynamic torques on a rigid Skylab-type satellite
A theoretical investigation of the influence of the aerodynamic torque on a Skylab-type satellite is presented. Only the case of free flow of uniform velocity and completely diffuse reflection is considered. It is found by linear stability analysis that the satellite has no stable equilibrium.
Sperling, H. J.↗
Method for evaluating effectiveness of dry fire-extinguishing chemicals
Apparatus used in method is commercially available, powder-deposition type oxy-acetylene torch that has been modified to provide electronically timed operations and more uniform powder flow; usual torch tips are replaced by burner head with pilot flame.
Altman, R. L.↗
Studies of scramjet/airframe integration techniques for hypersonic aircraft
New design and analysis techniques for engine-airframe integration were applied in a recent hypersonic vehicle design study. A new technique was developed to design the vehicle's forebody so that uniform precompressed flow was produced at the inlet entrance. Results are verified with three-dimensional characteristic calculations. Results from a new three-dimensional method for calculating nozzle flows show that the entire lower afterbody of the vehicle can be used as a scramjet exhaust nozzle to achieve efficient, controlled, and stable flight over a wide range of flight conditions.
Edwards, C. L. W.↗
Effect of slotted casing treatment on performance of a multistage compressor
A J85-13 engine was equipped with a compressor case that allowed changes to the case wall over the rotor tips of six of its eight stages. The engine was tested with four inlet configurations: uniform inlet flow, 180 degree circumferential distortion, hub radial distortion, and tip radial distortion. Slotted inserts were installed in the first three stages, and the compressor was mapped under similar conditions. Overall compressor performance obtained with tip treatment was inferior to the performance for the compressor's normal operating range. Pumping capacity with the slotted inserts was reduced. Overall compressor efficiency was reduced 1 to 2 percent with the slotted rings installed for 90 and 100 percent corrected engine speeds.
Moss, J. E., Jr.↗
Analytical and experimental studies of an optimum multisegment phased liner noise suppression concept
Results are presented from detailed analytical studies made to define methods for obtaining improved multisegment lining performance by taking advantage of relative placement of each lining segment. Properly phased liner segments reflect and spatially redistribute the incident acoustic energy and thus provide additional attenuation. A mathematical model was developed for rectangular ducts with uniform mean flow. Segmented acoustic fields were represented by duct eigenfunction expansions, and mode-matching was used to ensure continuity of the total field. Parametric studies were performed to identify attenuation mechanisms and define preliminary liner configurations. An optimization procedure was used to determine optimum liner impedance values for a given total lining length, Mach number, and incident modal distribution. Optimal segmented liners are presented and it is shown that, provided the sound source is well-defined and flow environment is known, conventional infinite duct optimum attenuation rates can be improved. To confirm these results, an experimental program was conducted in a laboratory test facility. The measured data are presented in the form of analytical-experimental correlations. Excellent agreement between theory and experiment verifies and substantiates the analytical prediction techniques. The results indicate that phased liners may be of immediate benefit in the development of improved aircraft exhaust duct noise suppressors.
Sawdy, D. T.↗
Stability derivatives for bodies of revolution at subsonic speeds
The paper considers a rigid pointed body of revolution in a steady uniform subsonic flow. The body performs harmonic small-amplitude pitching oscillations around its zero angle of attack position. The body is assumed to be smooth and sufficiently slender so that the small perturbation concept can be applied. The basis of the method used, following Revell (1960), is the relation of a body-fixed perturbation potential to the general velocity potential. Normal force distributions as well as total force and moment coefficients are calculated for parabolic spindles and the numerical results show good agreement between Revell's second-order slender body theory and the present theory for the static stability derivatives of the parabolic spindles.
Liu, D. D.↗
Nonlinear, unsteady aerodynamic loads on rectangular and delta wings
Nonlinear unsteady aerodynamic loads on rectangular and delta wings in an incompressible flow are calculated by using an unsteady vortex-lattice model. Examples include flows past fixed wings in unsteady uniform streams and flows past wings undergoing unsteady motions. The unsteadiness may be due to gusty winds or pitching oscillations. The present technique establishes a reliable approach which can be utilized in the analysis of problems associated with the dynamics and aeroelasticity of wings within a wide range of angles of attack.
Atta, E. H.↗
Modal density function and number of propagating modes in ducts
Often raised questions in duct sound propagation studies involve the total number of propagating modes, the number of propagating radial modes for a particular spinning lobe number, and the number of modes possible between two given values of cutoff ratio or eigenvalue. These questions can be answered approximately by using the modal distribution function which is the integral of the modal density function for ducts in a manner similar to that previously published for architectural acoustics. The modal density functions are derived for rectangular and circular ducts with a uniform steady flow. Results from this continuous theory are compared to the actual (discrete) modal distributions.
Rice, E. J.↗
Modal propagation angles in ducts with soft walls and their connection with suppressor performance
The angles of propagation of the wave fronts associated with duct modes are derived for a cylindrical duct with soft walls (acoustic suppressors) and a uniform steady flow. The angle of propagation with respect to the radial coordinate (angle of incidence on the wall) is shown to be a better correlating parameter for the optimum wall impedance of spinning modes than the previously used mode cutoff ratio. Both the angle of incidence upon the duct wall and the propagation angle with respect to the duct axis are required to describe the attenuation of a propagating mode. Using the modal propagation angles, a geometric acoustics approach to suppressor acoustic performance was developed. Results from this approximate method were compared to exact modal propagation calculations to check the accuracy of the approximate method. The results are favorable except in the immediate vicinity of the modal optimum impedance where the approximate method yields about one-half of the exact maximum attenuation.
Rice, E. J.↗
Internally coated air-cooled gas turbine blading
Ten candidate modified nickel-aluminide coatings were developed using the slip pack process. These coatings contain additives such as silicon, chromium and columbium in a nickel-aluminum coating matrix with directionally solidified MAR-M200 + Hf as the substrate alloy. Following a series of screening tests which included strain tolerance, dynamic oxidation and hot corrosion testing, the Ni-19A1-1Cb (nominal composition) coating was selected for application to the internal passages of four first-stage turbine blades. Process development results indicate that a dry pack process is suitable for internal coating application resulting in 18 percent or less reduction in air flow. Coating uniformity, based on coated air-cooled blades, was within + or - 20 percent. Test results show that the presence of additives (silicon, chromium or columbium) appeared to improve significantly the ductility of the NiA1 matrix. However, the environmental resistance of these modified nickel-aluminides were generally inferior to the simple aluminides.
Hsu, L.↗