Search NASA⌕ Search

SEARCH · Search NASA

Results for “WASTE UTILIZATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Enabling Partnership between South Carolina and NREL for Advancing Opportunities in Plastics Recycling Research (EPSCOR for Plastics Recycling)

Proposal Objectives: 1. Utilize depolymerization/fractionation techniques to recover highly processable and reactive feedstocks for polymer synthesis from lignin. 2. Synthesize lignin‐derived non‐isocyanate polyurethane, epoxy, and polyamide using non‐ toxic, biobased route designed for chemical recycling. Characterize resulting materials. 3. Design a high‐yielding chemical recycling process for as‐synthesized materials yielding usable building blocks for many generations of polymer synthesis. 4. Optimize chemical recycling of PET waste for the synthesis of lignin‐based polymers. Compare properties to commercial materials. 5. Optimize reaction conditions and recycling steps to facilitate enhanced sustainability of the synthetic steps and final properties of materials. 6. Complete a lifecycle assessment of lignin utilization and chemical recycling to compare their environmental performance to that of materials produced from virgin material. Identify hot spots and benefits using the chemical recycling process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reduction of Pertechnetate by Chemical and Photochemical Approaches and Incorporation of Tc(IV) into Titanium Dioxide

Technetium-99 is a prevalent fission product from nuclear waste. The long half-life (211,000 yr) and environmental mobility of pertechnetate (TcO 4 - ) render Tc particularly challenging to isolate and stabilize. Here, in this study, we present two approaches for development of potential wasteforms using titanium dioxide, TiO 2 . Approach 1 is a low temperature chemical synthesis of TiO 2 doped with Tc(IV) from TcO 4 - intended to mimic the Tc waste stream from the UREX family of separations and removes 98.5 % of the Tc, mainly present as edge-shared Tc(IV) pairs. Approach 2 utilizes TiO 2 to photocatalytically reduce TcO 4 - to Tc(IV) stabilized on the surface of or within the TiO 2 lattice. The %Tc removed from solution and adsorbed to TiO 2 is pH dependent, with the maximum Tc(IV) adsorbed at pH 3–4 as either TcO 2 or edge-sharing Tc(IV) octahedra. The Tc(IV)-TiO 2 composites materials formed by both approaches are suitable for consolidation into a dense wasteform by Hot Isostatic Pressing (HIPing).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Molecular Level Understanding of Polyethylene Terephthalate (PET) Depolymerization in Base/Alcohol Hybrid Systems

Polyethylene terephthalate (PET) depolymerization in base/alcohol hybrid systems represents a promising low-energy approach for chemically recycling PET waste into valuable monomers. This study investigates the mechanistic pathways of PET depolymerization in NaOH/alcohol solutions, emphasizing the competing roles of hydroxide and alkoxide species. Utilizing a combination of experimental techniques, density functional theory (DFT) calculations, and molecular dynamics (MD) simulations, we explore how factors such as base concentration, alcohol chain length, and pKa values of alcohols influence PET depolymerization efficiency and pathways. Our findings indicate that alkoxide ions (RO⁻) exhibit notably higher reactivity than hydroxide ions (HO⁻), favoring an alcoholysis pathway in the base/alcohol hybrid system. Experimental results across a series of C1 to C5 alcohols show that longer-chain alcohols, particularly 1-butanol, achieve higher PET conversion, although this does not align solely with simple nucleophilicity trends of alkoxides. While DFT calculations reveal comparable activation energies for various alkoxides in PET depolymerization, MD simulations underscore the significant role of alcohol chain length, with longer-chain alcohols forming more stable or frequent interactions with PET. Additionally, the alkoxide concentration, influenced by the alcohol’s pK a , directly impacts PET conversion. These suggest that PET depolymerization is governed by a balance between alkoxide concentration and alkoxide-PET interactions, rather than activation energies or nucleophilicity alone. From a practical perspective, incorporating long-chain alcohols as cosolvents may enhance process efficiency but increases raw material costs by approximately 30%. However, long-chain alcohols present a safer and more sustainable alternative to hazardous cosolvents such as dichloromethane. This work offers a molecular-level understanding of PET depolymerization in base/alcohol systems and provides insights into optimizing these systems for more efficient and sustainable PET recycling processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mathematical Foundations for Nonlocal Interface Problems: Multiscale Simulations of Heterogeneous Materials (Final LDRD Report)

Nonlocal models provide a much-needed predictive capability for important Sandia mission applications, ranging from fracture mechanics for nuclear components to subsurface flow for nuclear waste disposal, where traditional partial differential equations (PDEs) models fail to capture effects due to long-range forces at the microscale and mesoscale. However, utilization of this capability is seriously compromised by the lack of a rigorous nonlocal interface theory, required for both application and efficient solution of nonlocal models. To unlock the full potential of nonlocal modeling we developed a mathematically rigorous and physically consistent interface theory and demonstrate its scope in mission-relevant exemplar problems.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Mobile Hot Cell Digital Twin: End-of-life Management of Disused High Activity Radioactive Sources – 23598

Sealed radioactive sources are utilized for a wide range of applications across nuclear facilities, universities, hospitals, and industry. When these sources reach the end of serviceable life, they become waste. As waste, this radioactive material then goes through a process of recapture and then transfer to long term storage. With the advancement of technology in conjunction with better accessibility of technology, industries are exploring the use of digital automation to enhance productivity, efficiency, and safety while minimizing operation and maintenance costs, health and environmental risks, and uncertainty in the project life cycles. One area for exploration is the use of a digital twin to help design a robust, versatile, and safe solution for recapturing spent sources. We believe this avenue can also provide further advantages in the operations aspect of end-of-life management of spent radioactive sources by reducing the deployment time, increasing operator safety, and reducing operation & maintenance cost. We present a novel digital twin framework for end-of-life management of disused high activity radioactive sources. We have designed and developed a framework that houses a digital twin for visualizing and monitoring the recapture process to inform the engineering and design of a new Mobile Hot Cell. Furthermore, we demonstrate the feasibility of the proposed framework by providing a prototypical implementation, supporting the Mobile Hot Cell and human-machine interface's virtual replication.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2019

Current Status of Decommissioning Plans and Chemical Decontamination of Metal Scraps in Chinshan NPP - 19304

The decommissioning of nuclear facilities has become a significantly attractive and worldwide topic due to the end of lifetime of many nuclear power plants within next coming years. In Taiwan, Chinshan nuclear power plant owned by the Taiwan Power Company will be the first candidate to be decommissioned according to the Nuclear Reactor Facilities Regulation Act. The Chinshan nuclear power plant located in New Taipei City has two units of 636 MWe boiling water reactors (BWRs) for the generation of 9 billion kWh of electricity per year. The date of cessation of operation of Unit No. 1 and Unit No. 2 will be December in 2018 and July in 2019, respectively. Based on the Regulations for the Review and Approval of Applications for a Decommissioning Permit of Nuclear Reactor Facilities, Taiwan Power Company have submitted a decommissioning plan of Chinshan nuclear power plant to the authority, Atomic Energy Council (AEC). After the review process, the decommissioning plan of Chinshan nuclear power plant has been permitted by AEC in 2017. Decontamination is generally utilized during the period of decommissioning of nuclear facility in order to minimize the radiation exposure of personnel and the cost of management of radioactive wastes. The successful decontamination also probably provides the benefits of lowering the level of radioactive wastes, facilitating potential releases, permitting the reuse of metals and facilitating the radiation principle of As Low As Reasonably Achievable (ALARA) management. Decontamination aims at the removal of radioactive materials from the contaminated surfaces by several technologies such as washing, heating, chemical reaction and mechanical process. The selection of proper decontamination technologies are depended on the requirement of the target materials and the purpose of the decontamination. Chemical decontamination has been proven to be an effective in reducing the radioactivity for metallic materials by using chemical reagents in contact with the contaminated surfaces. During the operation of Chinshan nuclear power plant, chemical decontamination was performed for Unit No.1 and No.2 in 2000 to decontaminate the Reactor Recirculation System (RRS) and Reactor Water Clean-up Systems (RWCU) by using LOMI-NP-LOMI process. Based on the previous experience of chemical decontamination, the dismantled metallic piping is provided as sample by Chinshan nuclear power plant for the evaluation of the feasibility of chemical decontamination. The provided metallic sample is composed of carbon steel with dose rate around 0.2 mSv/hr. In this report, a multistep decontamination process using strongly oxidizing solution and organic acid solution is performed to remove the contaminated oxide layer from the metal surface, and the resulting contact dose rate and decontamination factor (DF) are also shown to discuss the performance in relation to the process control factors. In this paper, the recent progress in decommissioning programs and preliminary results of the decontamination experiment are described to provide usable information regarding the future decommissioning for Chinshan nuclear power plant. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Anthropogenic Markers in Alta Irrigation District Water Supply Wells

In July 2016, LLNL produced a report for the Kings River Watershed Coalition Authority (KRWCA) entitled “Groundwater Age and Nitrate Isotopic Composition in Alta Irrigation District Water Supply Wells” (Esser et al., 2016). That report summarized groundwater age and nitrate isotopic composition data produced by LLNL for Alta Irrigation District (AID) groundwater wells sampled by KRWCA in a pilot project to test the utility of advanced isotopic methods for constraining the timing and source of nitrate in groundwater at selected sites in the Kings River service area. One section of that report made recommendations for follow-on study. The first and strongest recommendation was to measure a wider suite of source tracers including co-contaminants such as herbicides, pesticides, pharmaceuticals, personal care products, and food constituents and additives. KRWCA followed up on this recommendation in Phase II of the pilot study by re-sampling the original set of wells and submitting the samples to a commercial laboratory for analysis of a limited range of co-contaminants (including pharmaceuticals, personal care products , and food constituents and additives, but not including herbicides or pesticides). They have asked that LLNL review and interpret these data in the context of previous LLNL analyses and to evaluate the utility of such co-contaminant analyses in providing additional constraints on the source of groundwater nitrate contamination in Alta Irrigation District water supply wells. The goal of the second phase of this pilot project is to evaluate the utility of co-contaminant occurrence for constraining nitrate source in groundwater at selected sites in the Kings River service area, with special reference to the use of such data in conjunction with advanced isotopic methods such as nitrate isotopic composition and groundwater age. Nitrate isotopic composition alone cannot distinguish nitrate derived from animal manure from nitrate derived from human septic waste. The presence or absence of agricultural chemicals (herbicides, pesticides, veterinary pharmaceuticals) or chemicals associated with people (human pharmaceuticals, artificial sweeteners) can help make this distinction. Co-contaminant analyses using multi-analyte LC-MS-MS protocols are now commercially available and reasonably priced. The feasibility and utility of the using co-contaminants for nitrate source attribution can be evaluated by 1) determining the degree to which co-contaminants occur in distinct and easily attributable groupings (e.g. agricultural chemicals vs personal care products and food additives); 2) determining the degree to which co-contaminant occurrence is consistent with nitrate isotopic composition and groundwater age (e.g. no co-contaminant occurrence in very old groundwater; co-contaminants consistent with animal manure or human septic waste occurring in groundwaters having nitrate isotopic composition also consistent with animal manure or human septic waste); and 3) determining the degree to which co-contaminants provide additional constraint on nitrate source over and beyond nitrate isotopic composition and groundwater age (e.g. distinguishing between animal manure and human septic waste).

58 GEOSCIENCES↗
DOE OSTI2025

Technoeconomic Analysis of a Microwave-Assisted Novel Process That Converts Polypropylene Plastic Waste to Propylene

Propylene is an important petrochemical that is used in various industries, including the automobile and polymer sectors. Conventionally, propylene has been produced through fluid catalytic cracking, steam cracking, and propane dehydrogenation. In this project, a novel process to produce propylene from polypropylene plastic waste using a microwave reactor is introduced. Propylene production is simulated in Aspen Plus for both the conventional propane dehydrogenation process and the novel design, with heat integration applied to minimize utility demands and the conventional process serving as the base case for comparison. Finally, a tailored technoeconomic analysis is carried out for both simulated cases to estimate important economic indicators. Analysis of the results shows that the novel microwave-assisted process outperforms the conventional route for propylene production, achieving a single-pass conversion of almost 100%, compared with only 33.8% in the conventional plant. The Net Present Value of the novel plant is $\$1720.3$ MM, which is 3.5 times higher than the conventional process, while the Levelized Cost of Propylene is reduced by 40%. Capital and operating expenditure are also improved in the proposed scheme, with reductions of approximately $\$29$ MM and $\$222$ MM/yr, respectively. In addition to cost savings, this novel process also provides a convenient means to recycle waste polypropylene.

42 ENGINEERING↗
DOE OSTI2023

Togiak Heat Recovery Project

Togiak is one of hundreds of Alaskan Native, roadless communities only accessible by boat or plane. This project constructed a heat recovery (HR) system which pipes what was previously wasted heat generated at the power plant to four nearby community buildings. The power plant houses diesel fired generators which provide electricity to the community. This project designed and constructed the system that recovers a portion of the heat produced by the generators and pipes it to the end-user buildings. The heat recovery system integrates with each building’s internal heating system. The objective is to significantly reduce the heating costs in these four community facilities. By reducing the energy use and cost in these community facilities, the local economy is strengthened by keeping the funds inside the community that were formerly used to purchase imported fuel, thereby multiplying the impact of the energy cost reduction. Energy independence is enhanced and energy resilience is increased by reducing dependence on long fuel supply chains which are easily interrupted by unpredictable natural and man-made disasters such as earthquakes, climate change, road rail and sea accidents, etc.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2019

Process intensification in a spinning disk absorber for absorption heat pumps

Absorption heat pumps are often an efficient machine for recovering of low-grade waste heat to cooling applications. However, they suffer from slow transfer processes and consequently large equipment size. This paper presents an experimental investigation of a novel absorber that utilizes a combination of a spinning disk and manifold-microchannel technology to intensify the absorption process. The rotation of the disk improves solution-side absorption performance, while an adaption of manifold-microchannel technology provides water-side enhancement. The enhanced spinning disk absorber was tested in an experimental setup using aqueous lithium bromide as the working fluid. Experimental results are compared with key performance metrics reported in the existing literature. The overall heat transfer increased by a factor of 4.7, and absorption rate increased by a factor of 4 to 10 folds over those in conventional tube absorbers. The results suggest that the spinning disk reactor could substantially reduce the size of absorber in the absorption machines. Better thermal and mass transfer performance can also enable air cooling with higher heat sink temperature than the one available through cooling towers.

42 ENGINEERING↗
DOE OSTI2020

Integrating Commercial Ready Autonomous Robotic Platforms to Enhance Worker Safety and Efficiency - 20053

This paper will explore the challenges and triumphs of implementing advanced robotic systems and the supporting technology for the waste management industry. Deployment-ready solutions for autonomous robotic platforms are new to the radioactive waste management industry and have been slow to implement across the complex. Specifically, it will explore Hanford Tank Operations Contractor's implementation of ground-based autonomous robotic platforms to enhance workforce safety and efficiency. The first objective of the project is to demonstrate safe operation of autonomous instrumented robots, followed by a scaling up of capabilities for the platform to meet any additional requests of internal stakeholders. Autonomous robotics platforms offer a fantastic range of capabilities that will aid in decreasing long-term liability of radioactive waste management industry by enhancing clean-up efforts and worker safety. Over the past five years, deployment-ready solutions for autonomous robotic platforms have come a long way. Autonomous robotic platforms are increasingly available to purchase from many vendors, often for prices under $100,000. Additionally, the vendors who produce these products are efficient in accommodating customized solutions to unique challenges, such as those often found in the radioactive waste management industry. However, the newness of this technology to the radioactive waste management industry and has resulted in a slow implementation across the complex. This paper will explore the challenges and triumphs of implementing advanced robotic systems and supporting technology for the waste management industry. Specifically, it will explore Hanford Tank Operations Contractor's implementation of ground based autonomous robotic platforms to enhance workforce safety and efficiency. While the company has utilized robots in many parts of the tank farms mission, this was first attempted in the deployment of an autonomous platform that required no operator with only minor maintenance and created challenges not yet encountered. These challenges included stakeholder buy-in, operational safety, procurement uncertainties, adaption of 'off the shelf products, overcoming the 'Fukushima complexity' perception, security concerns, and the initial criteria down select. Hanford Tank Operations Contractor's management identified the need for a workforce protecting low cost robotics solution in the fall of 2017. The project scope generated was part of the response to the Tank Vapor Assessment Team recommendation to enhance the safety of the workforce by utilizing new technology. Since the projects inception, it has been incorporated into the Tank Stewardship Plan. This project was unique to Hanford Tank Operations Contractor, as the company does not frequently incorporate advanced technology for field deployment quickly. The project was also progressive to the Hanford Tank Operations Contractor as it functions as a partnership project with a local university. The first objective of the project is to demonstrate safe operations of autonomous instrumented robotics, monitoring and collecting data, and the wireless transmission of data to a central computing system. Following the completion of this first objective, the project will scale up capabilities of the platform to meet the requests of additional internal stakeholders throughout the tank farms - including completion of specific in-field tasks. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Catalytic Upgrading of Pyrolysis Condensables from Postconsumer Polyolefins Using HZSM-5

The conversion of plastic wastes to monomeric olefins is an attractive means for achieving a plastic circular economy. In our study, a fluidized bed reactor converts post-consumer waste high-density polyethylene (HDPE) and polypropylene (PP) to mostly condensed pyrolysis waxes and some oils, preventing carbon loss to gases. The pyrolysis condensables were upgraded to light olefins (C 2 –C 5 ) at carbon yields greater than 76 wt % using the HZSM-5 zeolite catalyst at a post pyrolysis process that employed a micropyrolyzer. These results were comparable to olefin monomer yields from direct ex situ catalytic pyrolysis of the original waste plastics without condensing the vapors, highlighting the potential applicability of this approach in plastic waste recycling. Our results suggest that a centralized catalytic upgrading facility fed by pyrolysis condensables sourced from distributed thermochemical processing plants is a promising pathway to a circular economy. Such an approach enables utilization of available catalytic cracking infrastructure while focusing on setting up distributed thermochemical processing plants close to material recovery facilities. As a result, the energy-dense pyrolysis waxes are more suitable for transportation, contributing to the overall scalability and economic viability of the proposed distributed approach.

10 SYNTHETIC FUELS↗
DOE OSTI2021

Editorial: Microbial C1 Metabolism and Biotechnology

Archaea and bacteria with the capacity to utilize one-carbon (C1) molecules as carbon and energy sources are widespread across the planet and are important players in many biogeochemical processes. As such, they occupy an array of diverse anaerobic and aerobic niches and perform unique metabolisms that enable the utilization of carbon dioxide (CO 2 ), carbon monoxide (CO), formate (HCOOH), methanol (CH 3 OH), and methane (CH 4 ) for growth. Several industrial processes have been developed that leverage these microbes for the targeted conversion of anthropogenic waste gases that contain C1 molecules, including natural gas (CH 4 ), anaerobic digestion-derived biogas (CH 4 and CO 2 ), industrial flue gas (CO 2 and CO), and syngas (CO 2 , CO, and H 2 ) (Figure 1). Further, there is increasing interest in electrochemical reduction of CO 2 to CO, CH 4 , and intermediates with increased solubility compared to gaseous C1 molecules (formate and methanol) using electrons derived from renewable sources like wind, solar, or hydrothermal systems to mitigate atmospheric greenhouse gas. Thus, C1-utilizing microbes will likely play an integral role in biotechnologies that are part of a sustainable, circular bioeconomy. However, fundamental knowledge gaps into the metabolism and physiology of these microbes exist that limit their utility as biocatalysts for carbon-efficient biomanufacturing. This special topic presents studies focused on the fundamental aspects of C1 metabolism in diverse microbial systems with the ability to convert anthropogenic greenhouse gases into valuable products.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Waste to worth: a circular solution through lignin engineering

The inefficient management of industrial waste threatens environmental sustainability, requiring scalable resource recovery solutions. To address these challenges, we propose a novel and sustainable in-situ one-step strategy for the simultaneous recovery and functionalization of lignin from industrial black liquor, using a sustainable organic acid system assisted by choline chloride. The functionalized lignin adsorbent material (FLAM) exhibited superior adsorption performance, effectively treating animal feedlot wastewater to recover ammonia. The ammonia enriched FLAM was subsequently repurposed as a slow-release fertilizer, enhancing plant growth and demonstrating a closed-loop pathway for waste valorization and nutrient recycling. Methylene blue was used as a model cationic compound to simulate the adsorption behavior and interactions. FLAM achieved a high adsorption capacity of 725.98 mg/g across a broad pH range, significantly outperforming commercial kraft lignin. This sustainable approach advances circular economy principles by integrating remediation and resource recovery, offering a scalable, eco-friendly solution for environmental applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

UF Industrial Assessment Center - Budget Periods 2017-2021. Final Report

This report summarizes the work performed at the University of Florida’s Industrial Assessment Center (UF-IAC) during the five budget periods (BPs) in the years 2017 through 2021 under DOE Award No. DE-EE0007707. The objective of the work is to perform industrial assessments to small- and medium-sized manufacturing facilities in the State of Florida and to train students in industrial energy management and in performing industrial assessments. Specific details about the activities of the UF-IAC (referred to as the Center) during that time can be found in the 20 quarterly reports that were submitted throughout the duration of the contract. The project start and end dates are September 1, 2016 and August 31, 2021, respectively. The project was granted a six-month no-cost extension till February 28, 2022, to accommodate unexpected delays due to the COVID-19 pandemic. This project was performed by the University of Florida (PI: Dr. SA Sherif). The scope of work includes six milestone whose description and outcomes are listed in the Statement of Project Objectives (SOPO).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Mobile Hot Cell Digital Twin using Immersive Virtual Environment

Sealed radioactive sources are utilized for a wide range of applications across nuclear facilities, universities, hospitals, and industry. When these sources reach the end of their serviceable life, they become waste. This radioactive waste then goes through a process of recapture and then transfer to long term storage. With the advancement of technology in conjunction with better accessibility of technology, industries are exploring the use of digital automation to enhance productivity, efficiency, and safety while minimizing operation and maintenance costs, health and environmental risks, and uncertainty in the project life cycles. One area for exploration and the use of Digital Twin for providing a robust, versatile, and safe solution for recapturing spent sources.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2025

Considerations for Distributed Edge Data Centers and Use of Building Loads to Support Large Interconnections

The rapid expansion of artificial intelligence (AI) and machine learning is driving unprecedented electricity demand from data centers. It is predicted that by 2030, 90% of AI workloads will be inference-based, requiring interconnection of multiple low-latency edge data centers (<20 MW) sited closer to end users - often on already constrained distribution feeders. Although individually small, these loads can aggregate to large loads per feeder, straining infrastructure, creating multi-year interconnection delays, and driving up customer costs. This paper proposes a data center-focused grid-integration framework that combines feeder hosting capacity analysis with building energy efficiency, building load flexibility, and waste heat reuse to expand effective feeder and substation headroom. Such approaches can reduce interconnection delays, lower costs for ratepayers, and accelerate AI-ready infrastructure deployment.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗