Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, COMPLETE - SWEEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

The Screem-J4D: A proposal in response to a low Reynolds number station keeping mission

The Screem-J4D is a remotely piloted airplane that was designed to fly at a chord Reynold's number of 100,000 while performing figure-8 maneuvers in a restricted area. It has a high aspect ratio main wing with a conventional empennage giving it a sailplane appearance. A specifications table and three-view drawing is provided. The flight plan calls for ascent to cruise altitude at 20 ft and then perform three figure-8 turns around pylons. These pylons will be separated by fifty yards and stationed inside a sports facility. Once completed, the pilot is to make use of any remaining power by loitering before landing the plane. The propulsion system of the J4D consists of a propeller-electric motor combination with the prop mounted at the front of the fuselage. In order to provide sufficient lift for low speed travel, the J4D has an aspect ratio of 11.72 with an 8.2 inch mean chord. The wing consists of a spar and rib construction with Micafilm skin. A combination of directional and longitudinal control will enable the J4D to perform the figure-8 maneuvers. However, in order to avoid the construction and servo weight of ailerons, the rudder was designed to be over one-half the size of the vertical tail to insure that the proper roll motion could be attained.

Source record↗
NASA NTRS1974

Three dimensional flows around airfoils with shocks

The present work describes a mathematical model and numerical scheme for the computer-aided calculation of two- and three-dimensional transonic flow over an isolated yawed wing with oblique shock waves and a trailing vortex sheet. The flow is modeled by the potential equation for irrotational flow which is hyperbolic at supersonic points and elliptic at subsonic points. A coordinate-invariant difference scheme is used in which retarded difference formulas are constructed to conform with the local flow direction. The resulting 'rotated' difference scheme allows complete flexibility in the choice of a coordinate system. Shock waves are located automatically in the form of compression bands spread over a few mesh widths. The scheme has proven to be stable and convergent throughout the transonic range. Calculations have been performed for Mach number up to 1.2 and yaw angles up to 60 deg, the likely operating range of a yawed-wing transport designed to fly at supersonic speeds. Calculations becomes less accurate towards upper end of range, because the difference scheme is first-order accurate in the supersonic range.

Jameson, A.↗
NASA NTRS1990

The application of CFD to rotary wing flow problems

Rotorcraft aerodynamics is especially rich in unsolved problems, and for this reason the need for independent computational and experimental studies is great. Three-dimensional unsteady, nonlinear potential methods are becoming fast enough to enable their use in parametric design studies. At present, combined CAMRAD/FPR analyses for a complete trimmed rotor soltution can be performed in about an hour on a CRAY Y-MP (or ten minutes, with multiple processors). These computational speeds indicate that in the near future many of the large CFD problems will no longer require a supercomputer. The ability to convect circulation is routine for integral methods, but only recently was it discovered how to do the same with differential methods. It is clear that the differential CFD rotor analyses are poised to enter the engineering workplace. Integral methods already constitute a mainstay. Ultimately, it is the users who will integrate CFD into the entire engineering process and provide a new measure of confidence in design and analysis. It should be recognized that the above classes of analyses do not include several major limiting phenomena which will continue to require empirical treatment because of computational time constraints and limited physical understanding. Such empirical treatment should be included, however, into the developing CFD, engineering level analyses. It is likely that properly constructed flow models containing corrections from physical testing will be able to fill in unavoidable gaps in the experimental data base, both for basic studies and for specific configuration testing. For these kinds of applications, computational cost is not an issue. Finally, it should be recognized that although rotorcraft are probably the most complex of aircraft, the rotorcraft engineering community is very small compared to the fixed-wing community. Likewise, rotorcraft CFD resources can never achieve fixed-wing proportions and must be used wisely. Therefore the fixed-wing work must be gleaned for many of the basic methods.

Caradonna, F. X.↗
NASA NTRS1991

A comparison of classical mechanics models and finite element simulation of elastically tailored wing boxes

Structural tailoring concepts were developed to create wings with elastically produced camber for the purpose of increasing lift during takeoff conditions. Simple models based upon enhancements to the thin walled composite beam theory of Rehfield were developed to investigate prospects for elastic tailoring of the chordwise deformation of wing structures. The purpose here is to provide a comparison of the theoretical results with a finite element model for the bending method of producing camber. Finite element correlation studies were completed for two cases: a bonded unstiffened structural box, and a bolted unstiffened structural box. Results from these studies show an error of less than one percent for the bonded case and less than six percent for the bolted case in predicting camber curvature for the structural box. Examination of the results shows that the theory is very accurate for the cases studied and will provide an excellent basis for conducting further tailoring studies.

Rehfield, Lawrence W.↗
NASA NTRS1992

Efficient computation of inviscid flow fields around complex configurations using a multiblock multigrid method

The applicability of a multigrid technique to block-structured, body-fitted meshes is examined focusing on three different strategies. In the first strategy data are exchanged between blocks in each stage of a five-stage Runge-Kutta time-stepping scheme which keeps a possible time lag between blocks to a minimum, but requires a large amount of I/O operations and storage. The second strategy is based on performing a complete Runge-Kutta cycle within a block before switching to the next. In the third strategy both a complete Runge-Kutta cycle and the residual evaluation for the restriction operator are done within a block, allowing a minimum of I/O and storage. The inviscid flow around a wing-body/engine-pylon configuration was computed on a mesh consisting of 11 computational blocks. It was found that both the first and the second strategies delivered converged results, but the third failed due to larger time lag between blocks.

Rossow, C.-C.↗
NASA NTRS1947

Pressure-Distribution Measurements on a Straight and on a 35 Degree Swept-Back Tapered Wing

The spanwise lift-distribution measurements in straight air flow on a straight and a 35 deg swept-back tapered wing (NACA airfoil section 0012) are compared with theory for two angles of attack each (alpha approx. 6 deg and alpha approx. 12 deg) in the unstalled range of flow. The complete pressure distribution for the greater of the two angles is indicated.

Thiel, A.↗
NASA NTRS2005

Ground-based Photon Path Measurements from Solar Absorption Spectra of the O2 A-band

High-resolution solar absorption spectra obtained from Table Mountain Facility (TMF, 34.38degN, 117.68degW, 2286 m elevation) have been analyzed in the region of the O2 A-band. The photon paths of direct sunlight in clear sky cases are retrieved from the O2 absorption lines and compared with ray-tracing calculations based on the solar zenith angle and surface pressure. At a given zenith angle, the ratios of retrieved to geometrically derived photon paths are highly precise (approx.0.2%), but they vary as the zenith angle changes. This is because current models of the spectral lineshape in this band do not properly account for the significant absorption that exists far from the centers of saturated lines. For example, use of a Voigt function with Lorentzian far wings results in an error in the retrieved photon path of as much as 5%, highly correlated with solar zenith angle. Adopting a super-Lorentz function reduces, but does not completely eliminate this problem. New lab measurements of the lineshape are required to make further progress.

Yang, Z.↗
NASA NTRS1956

Tabulated Pressure Data for a Series of Controls on a 60 Degree Delta Wing at Mach Numbers of 1.61 and 2.01

An investigation has been made at Mach numbers of 1.61 and 2.01 and Reynolds numbers from 1.7 X 10 to 7.6 X 10 to determine the pressure distributions over a 60 deg. delta wing having 20 different control configurations. Measurements were made at angles of attack from O deg to 15 deg for control deflections from -30 deg to 30 deg. This report presents the complete tabulated pressure data for the range of test conditions.

Lord, Douglas R↗
NASA NTRS2001

Computation of External Aerodynamics for a Canard Rotor/Wing Aircraft

The aerodynamic loads on a Canard Rotor/Wing vehicle are investigated using inviscid numerical simulations in order to understand the flight characteristics of the vehicle during conversion from rotor craft to fixed-wing flight. A series of numerical simulations at seven azimuthal rotor indices are presented covering a quarter turn of the rotor With symmetry arguments, these simulations produce 25 data points for a complete rotation. A Cartesian mesh approach is used to compute the flow field about a configuration with faired-over engine inlet and exhaust that matches the wind tunnel geometry. These simulations were performed using meshes with approximately nine Million Cartesian cells. To better understand the aerodynamic effects of the rotor hub on the configuration, the same set of simulations were repeated for a hub-less geometry. Overall loads for both configurations are similar but are due to somewhat different aerodynamic mechanisms.

Pandya, S. A.↗
NASA NTRS2012

Acoustic Surveys of a Scaled-Model CESTOL Transport Aircraft in Static and Forward Speed Conditions

An 11% scale-model of a Cruise-Efficient Short Take-off and Landing (CESTOL) scalemodel test was recently completed. The test was conducted in the AEDC National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The model included two over-wing pod-mounted turbine propulsion simulators (TPS). The hybrid blended wing-body used a circulation control wing (CCW) with leadingand trailing-edge blowing. The bulk of the test matrix included three forward velocities (40 kts, 60 kts, and 100kts), angle-of-attack variation between -5 and 25 , and CCW mass flow variation. Seven strut-mounted microphones outboard of the left wing provided source directivity. A phased microphone array was mounted outboard of the right wing for source location. The goal of this paper is to provide a preliminary look at the acoustic data acquired during the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) test for 0 angle-of-attack and 0 sideslip conditions. Data presented provides a good overview of the test conditions and the signal-to-noise quality of the data. TPS height variation showed a difference of 2 dB to 3 dB due to wing shielding. Variation of slot mass flow showed increases of 12 dB to 26 dB above the airframe noise and the TPS increased the overall levels an additional 5 dB to 10 dB.

Burnside, Nathan↗
NASA NTRS2014

Space Shuttle Boundary Layer Transition Flight Experiment Ground Testing Overview

In support of the Boundary Layer Transition (BLT) Flight Experiment (FE) Project in which a manufactured protuberance tile was installed on the port wing of Space Shuttle Orbiter Discovery for STS-119, STS- 128, STS-131 and STS-133 as well as Space Shuttle Orbiter Endeavour for STS-134, a significant ground test campaign was completed. The primary goals of the test campaign were to provide ground test data to support the planning and safety certification efforts required to fly the flight experiment as well as validation for the collected flight data. These test included Arcjet testing of the tile protuberance, aerothermal testing to determine the boundary layer transition behavior and resultant surface heating and planar laser induced fluorescence (PLIF) testing in order to gain a better understanding of the flow field characteristics associated with the flight experiment. This paper provides an overview of the BLT FE Project ground testing. High-level overviews of the facilities, models, test techniques and data are presented, along with a summary of the insights gained from each test.

Karen T Berger↗
NASA NTRS2014

TPSAS-NF1676L-19423-DND

In support of the Boundary Layer Transition (BLT) Flight Experiment (FE) Project in which a manufactured protuberance tile was installed on the port wing of Space Shuttle Orbiter Discovery for STS-119, STS-128, STS-131 and STS-133 as well as Space Shuttle Endeavour for STS-134, a significant wind tunnel test campaign was completed. The primary goals of the test campaign were to provide ground test data to support the planning and safety certification efforts required to fly the flight experiment as well as validation for the collected flight data. These test included Arcjet testing of the tile protuberance, aerothermal testing to determine the boundary layer transition behavior and resultant surface heating and planar laser induced fluorescence (PLIF) testing in order to gain a better understanding of the flow field characteristics of the flight experiment. This paper provides an overview of the BLT FE Project ground testing. High-level overviews of the facilities, models, test techniques and data are presented, along with a summary of the insights gained from each test.

Karen T Berger↗
NASA NTRS1989

Currents between tethered electrodes in a magnetized laboratory plasma

Laboratory experiments on important plasma physics issues of electrodynamic tethers were performed. These included current propagation, formation of wave wings, limits of current collection, nonlinear effects and instabilities, charging phenomena, and characteristics of transmission lines in plasmas. The experiments were conducted in a large afterglow plasma. The current system was established with a small electron-emitting hot cathode tethered to an electron-collecting anode, both movable across the magnetic field and energized by potential difference up to V approx.=100 T(sub e). The total current density in space and time was obtained from complete measurements of the perturbed magnetic field. The fast spacecraft motion was reproduced in the laboratory by moving the tethered electrodes in small increments, applying delayed current pulses, and reconstructing the net field by a linear superposition of locally emitted wavelets. With this technique, the small-amplitude dc current pattern is shown to form whistler wings at each electrode instead of the generally accepted Alfven wings. For the beam electrode, the whistler wing separates from the field-aligned beam which carries no net current. Large amplitude return currents to a stationary anode generate current-driven microinstabilities, parallel electric fields, ion depletions, current disruptions and time-varying electrode charging. At appropriately high potentials and neutral densities, excess neutrals are ionized near the anode. The anode sheath emits high-frequency electron transit-time oscillations at the sheath-plasma resonance. The beam generates Langmuir turbulence, ion sound turbulence, electron heating, space charge fields, and Hall currents. An insulated, perfectly conducting transmission line embedded in the plasma becomes lossy due to excitation of whistler waves and magnetic field diffusion effects. The implications of the laboratory observations on electrodynamic tethers in space are discussed.

Stenzel, R. L.↗
NASA NTRS2005

Experimental Investigation of Ice Accretion Effects on a Swept Wing

An experimental investigation was conducted to study the effects of 2-, 5-, 10-, and 22.5-min ice accretions on the aerodynamic performance of a swept finite wing. The ice shapes tested included castings of ice accretions obtained from icing tests at the NASA Glenn Icing Research Tunnel (IRT) and simulated ice shapes obtained with the LEWICE 2.0 ice accretion code. The conditions used for the icing tests were selected to provide five glaze ice shapes with complete and incomplete scallop features and a small rime ice shape. The LEWICE ice shapes were defined for the same conditions as those used in the icing tests. All aerodynamic performance tests were conducted in the 7- x 10-ft Low-Speed Wind Tunnel Facility at Wichita State University. Six component force and moment measurements, aileron hinge moments, and surface pressures were obtained for a Reynolds number of 1.8 million based on mean aerodynamic chord and aileron deflections in the range of -15o to 20o. Tests were performed with the clean wing, six IRT ice shape castings, seven smooth LEWICE ice shapes, and seven rough LEWICE ice shapes. Roughness for the LEWICE ice shapes was simulated with 36-size grit. The experiments conducted showed that the glaze ice castings reduced the maximum lift coefficient of the clean wing by 11.5% to 93.6%, while the 5-min rime ice casting increased maximum lift by 3.4%. Minimum iced wing drag was 133% to 3533% greater with respect to the clean case. The drag of the iced wing near the clean wing stall angle of attack was 17% to 104% higher than that of the clean case. In general, the aileron remained effective in changing the lift of the clean and iced wings for all angles of attack and aileron deflections tested. Aileron hinge moments for the iced wing cases remained within the maximum and minimum limits defined by the clean wing hinge moments. Tests conducted with the LEWICE ice shapes showed that in general the trends in aerodynamic performance degradation of the wing with the simulated ice shapes were similar to those obtained with the IRT ice shape castings. However, in most cases, the ice castings resulted in greater aerodynamic performance losses than those obtained with the LEWICE ice shapes. For the majority of the LEWICE ice shapes, the addition of 36-size grit roughness to the smooth ice shapes increased aerodynamic performance losses.

Ice shape↗
NASA NTRS2014

Thrust Removal Scheme for the FAST-MAC Circulation Control Model Tested in the National Transonic Facility

A second wind tunnel test of the FAST-MAC circulation control semi-span model was recently completed in the National Transonic Facility at the NASA Langley Research Center. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged flap. The model was configured for transonic testing of the cruise configuration with 0deg flap deflection to determine the potential for drag reduction with the circulation control blowing. Encouraging results from analysis of wing surface pressures suggested that the circulation control blowing was effective in reducing the transonic drag on the configuration, however this could not be quantified until the thrust generated by the blowing slot was correctly removed from the force and moment balance data. This paper will present the thrust removal methodology used for the FAST-MAC circulation control model and describe the experimental measurements and techniques used to develop the methodology. A discussion on the impact to the force and moment data as a result of removing the thrust from the blowing slot will also be presented for the cruise configuration, where at some Mach and Reynolds number conditions, the thrust-removed corrected data showed that a drag reduction was realized as a consequence of the blowing.

Chan, David T.↗
NASA NTRS2012

Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA)

With the very recent advent of NASA's Environmentally Responsible Aviation Project (ERA), which is dedicated to designing aircraft that will reduce the impact of aviation on the environment, there is a need for research and development of methodologies to minimize fuel burn, emissions, and reduce community noise produced by regional airliners. ERA tackles airframe technology, propulsion technology, and vehicle systems integration to meet performance objectives in the time frame for the aircraft to be at a Technology Readiness Level (TRL) of 4-6 by the year of 2020 (deemed N+2). The proceeding project that investigated similar goals to ERA was NASA's Subsonic Fixed Wing (SFW). SFW focused on conducting research to improve prediction methods and technologies that will produce lower noise, lower emissions, and higher performing subsonic aircraft for the Next Generation Air Transportation System. The work provided in this investigation was a NASA Research Announcement (NRA) contract #NNL07AA55C funded by Subsonic Fixed Wing. The project started in 2007 with a specific goal of conducting a large-scale wind tunnel test along with the development of new and improved predictive codes for the advanced powered-lift concepts. Many of the predictive codes were incorporated to refine the wind tunnel model outer mold line design. The large scale wind tunnel test goal was to investigate powered lift technologies and provide an experimental database to validate current and future modeling techniques. Powered-lift concepts investigated were Circulation Control (CC) wing in conjunction with over-the-wing mounted engines to entrain the exhaust to further increase the lift generated by CC technologies alone. The NRA was a five-year effort; during the first year the objective was to select and refine CESTOL concepts and then to complete a preliminary design of a large-scale wind tunnel model for the large scale test. During the second, third, and fourth years the large-scale wind tunnel model design would be completed, manufactured, and calibrated. During the fifth year the large scale wind tunnel test was conducted. This technical memo will describe all phases of the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) project and provide a brief summary of the background and modeling efforts involved in the NRA. The conceptual designs considered for this project and the decision process for the selected configuration adapted for a wind tunnel model will be briefly discussed. The internal configuration of AMELIA, and the internal measurements chosen in order to satisfy the requirements of obtaining a database of experimental data to be used for future computational model validations. The external experimental techniques that were employed during the test, along with the large-scale wind tunnel test facility are covered in great detail. Experimental measurements in the database include forces and moments, and surface pressure distributions, local skin friction measurements, boundary and shear layer velocity profiles, far-field acoustic data and noise signatures from turbofan propulsion simulators. Results and discussion of the circulation control performance, over-the-wing mounted engines, and the combined performance are also discussed in great detail.

Subsonic Fixed Wing↗
NASA NTRS1972

Design integration and noise study for a large STOL augmentor wing transport

Analysis, design, experimental static testing, wind-tunnel testing, and design integration studies are used to develop an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program has three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind-tunnel testing to determine flight-speed effects on performance, and (3) system design and evaluation that optimizes the complete system and ensures that the design is compatible with the requirements for a large STOL transport having a 500-foot sideline noise of 95 perceived noise decibels (PNdb) or less.

Okeeke, J. V.↗
NASA NTRS1974

Flutter suppression and gust alleviation using active controls

The effects of active controls on the suppression of flutter and gust alleviation of two different types of subsonic aircraft (the Arava, twin turboprop STOL transport, and the Westwind twin-jet business transport) are investigated. The active controls are introduced in pairs which include, in any chosen wing strip, a leading-edge (LE) control and a trailing-edge (TE) control. Each control surface is allowed to be driven by a combined linear-rotational sensor system, located on the activated strip. The control law, which translates the sensor signals into control surface rotations, is based on the concept of aerodynamic energy. The results indicate the extreme effectiveness of the active systems in controlling flutter. A single system spanning 10% of the wing semispan made the Arava flutter-free, and a similar active system, for the Westwind aircraft, yielded a reduction of 75% in the maximum bending moment of the wing and a reduction of 90% in the acceleration of the cg of the aircraft. Results for simultaneous activation of several LE - TE systems are presented. Further work needed to bring the investigation to completion is also discussed.

Nissim, E.↗