SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Systematic investigation of effects on panel response and stability of nonlinear aerodynamic loading at hypersonic speeds
Aerodynamic load effects on propeller blade design
Trajectory, load, aerodynamic heating, materials, structural, and thermal analyses for hypersonic cruise vehicle wings
Aerodynamic loads produced by winds and launch vehicle designing
A theoretical investigation has been made of the flutter, vibration, and buckling of truncated conical shells with generalized elastic edge restraint. The shell analysis is of the classical Donnell type, in-plane inertias and structural damping are neglected, and the aerodynamic loading is represented by the inviscid two-dimensional quasi-steady approximation. An approximate solution is obtained by the generalized Galerkin method. The accuracy and limitations of the analysis are illustrated by comparing numerical results for buckling an vibration with results of other investigations for various boundary conditions, applied loads, and shell geometries and stiffness. Sufficient numerical results are presented to permit the determination of the flutter condition for simply supported isotropic conical shells for a wide range of cone angle, length-radius ration, and radius-thickness ratio. Results are also presented to indicate some effects of variations in edge restraint, applied loads, and ring or stringer stiffening.
Wind-launch vehicle interaction in flight, using equations of motion for aerodynamic loads
Unsteady nonlinear aerodynamic loads measurements in wind tunnel, using linearized mathematical analog
Wind tunnel balance for measuring small aerodynamic loads on scale models, describing three component construction
Oscillating wing aerodynamic load boundary value problem reduction to sequence of steady lifting- surface problems
Stability and postcritical response of infinite width panels on hinged supports due to aerodynamic loads at hypersonic speed
Aircraft wings automated preliminary structural design and weight determination procedures based on external shape, aerodynamic loads and fuel mass interaction
Method, developed and coded for digital computation, predicts aerodynamic loading on configurations for which linear theory assumptions are violated. Program is written in FORTRAN 4 for use on CDC-6000 series computers.
A cursory review is presented of some of the recent work that has been done in turbine aerodynamic research at NASA-Lewis Research Center. Topics discussed include the aerodynamic effect of turbine coolant, high work-factor (ratio of stage work to square of blade speed) turbines, and computer methods for turbine design and performance prediction. An extensive bibliography is included. Experimental cooled-turbine aerodynamics programs using two-dimensional cascades, full annular cascades, and cold rotating turbine stage tests are discussed with some typical results presented. Analytically predicted results for cooled blade performance are compared to experimental results. The problems and some of the current programs associated with the use of very high work factors for fan-drive turbines of high-bypass-ratio engines are discussed. Turbines currently being investigated make use of advanced blading concepts designed to maintain high efficiency under conditions of high aerodynamic loading. Computer programs have been developed for turbine design-point performance, off-design performance, supersonic blade profile design, and the calculation of channel velocities for subsonic and transonic flow fields. The use of these programs for the design and analysis of axial and radial turbines is discussed.
The vibration and buckling characteristics of a series of 140 deg ring-supported conical shells have been investigated experimentally and analytically. Experimental results were obtained from 14 conical shells, each attached to a solid nose cap at the small end. The large (base) end was either free or attached to a solid ring of rectangular cross section. The size of the solid base rings of rectangular cross section was systematically varied to provide a wide range of edge restraint. Shell buckling was induced by aerodynamic loading at a Mach number of 3; the vibration data were obtained prior to the wind tunnel tests. The experimental vibration data indicated that the size of the base rings had a pronounced effect on the magnitude of the frequencies and on the frequency spectrum. For vibration modes having less than two circumferential waves, the frequencies descreased with increasing ring size; whereas, for modes with several circumferential waves, the frequencies initially increased rapidly with ring size and then became relatively insensitive to further increases in ring size. This latter behavior was similar to the trend exhibited by the variation of buckling pressure with ring size. The experimental results were in excellent qualitative agreement with theoretical results and indicated that current shell-of-revolution analyses are adequate for predicting the vibration and buckling behavior of ring-supported shells, at least for the simple isotropic shells considered in this investigation.
This report presents the aerodynamic component test results of Fan C, a high-bypass-ratio, low-aerodynamic-loading, 1550 feet per second (472.4 m/sec), single-stage fan, which was designed and tested as part of the NASA Experimental Quiet Engine Program. The fan was designed to deliver a bypass pressure ratio of 1.60 with an adiabatic efficiency of 84.2 percent at a total fan flow of 915 lb/sec (415.0 kg/sec). It was tested with and without inlet distortion. A bypass total-pressure ratio of 1.61 and an adiabatic efficiency of 83.9 percent at a total fan flow of 921 lb/sec (417.8 kg/sec) were actually achieved. An operating margin in excess of 14.6 percent was demonstrated at design speed.
The aeroelastic instability of the coupled nonlinear flap-lag motion of a torsionally rigid helicopter blade is treated by using the perturbation method in multiple time scales. The nonlinearities present in the equations are those arising from the inclusion of moderately large deflections in the inertia and aerodynamic loading terms. The stability boundaries, amplitudes of nonlinear response, and conditions for existence of limit cycles are obtained analytically. Thus the different roles played by the forcing, parametric excitation, and nonlinear coupling in affecting the solution can be easily identified. Numerical results illustrating the behavior of the blade are presented.
Experimental aerodynamic investigations were conducted during mid-July, 1973 on a .004 scale model of the Rockwell International integrated configuration Space Shuttle Vehicle 3. The purpose of the tests was three fold: (1) to determine the static stability characteristics of the integrated vehicle, utilizing the Vehicle 3 orbiter configuration; (2) to determine the effect of interstage structure and tank external fuel lines on the integrated vehicle aerodynamic characteristics; (3) to determine the effects of the aft interstage structure on orbiter aerodynamic loads. Data were recorded on the integrated vehicle (test no. 579) at angles of attack and sideslip ranging from -10 deg to 10 deg over a Mach number schedule from 0.6 to 4.96. Data were obtained on the orbiter alone in the presence of the external tank with SRB attached (test no. 580) at angles of attack from -10 deg to 10 deg over a Mach number range from .6 to 1.96. Plotted data are presented in the body axis system.
An application of NASTRAN to the structural analysis of light aircraft was conducted to determine the cost effectiveness. A model of the Baby Ace D model homebuilt aircraft was used. The NASTRAN model of the aircraft consists of 193 grid points connected by 352 structural members. All members are either rod or beam elements, including bending of unsymmetrical cross sections and torsion of noncircular cross sections. The aerodynamic loads applied to the aircraft were in accordance with FAA regulations governing the utility category aircraft.