Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fracture behavior of irradiation induced nanocrystalline UO 2 studied by in-situ mechanical testing in transmission electron microscopy

Uranium Dioxide (UO 2 ) is widely used as a fuel in current light water reactors (LWRs). Upon accumulation of radiation damage, LWR UO 2 fuel pellets start to develop a different microstructure at the pellet periphery when fuel burnup exceeds 45–50 GWd/tHM. The resulting porous, nanocrystalline microstructure is one of the most prominent microstructural changes occurring in such fuel. Its fracture mechanisms, which causes fuel fine fragmentation, could impact safety limits when the cladding breaches. Direct measurements of these properties are challenging, therefore a surrogate obtained via ion irradiation can be used. In this study, multiple microcantilevers were fabricated by focused ion beam from both fresh UO 2 and UO 2 irradiated with 84 MeV Xe 26+ ions to a peak dose of 1357 displacements per atom (dpa). Further, the irradiation produced a pseudo high burnup structure approximately 2 µm below the surface. In-situ nano-mechanical bending tests were conducted to investigate the fracture behavior and the effect of the surrogate UO 2 high burnup structure on local fracture properties. Fresh UO 2 fuel was observed to fracture in transgranular mode without nucleation or movement of dislocations. However, the Xe-irradiated nanocrystalline microcantilevers fractured along the grain boundaries, with no influence from the pre-existing micro-cracks in the microcantilever. Fracture toughness for this type of surrogate high burnup UO 2 structure is reported for the first time in literature. Both the fracture stress and toughness show degradation for UO 2 as a result of Xe-irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Surface-Initiated Atom Transfer Radical Polymerization Using Hydrogel Reactors

Atom transfer radical polymerization (ATRP) is a controlled radical polymerization method that enables the synthesis of tailored polymeric materials with low dispersity, highlighting its immense potential for green fabrication of advanced materials. However, its broader implementation is limited by challenges in product isolation, maintaining catalyst activity, and mitigating atmospheric sensitivity arising from oxygen-sensitive metal catalysts. Here, gelatin hydrogels (GHs) are introduced as a soft “reactor” matrix for interfacial ATRP, operating with minimal metal-catalyst loading while exhibiting possibly an organoreductive behavior. This strategy leverages activator regeneration via electron transfer through a ligand–metal charge-transfer (LMCT) mechanism to reduce oxidized metal catalysts within the GH network. Polymerization is evaluated by growing polymer brushes at an active interface formed between GHs swollen in monomer solution and an initiating surface, and sequential growth experiments confirmed that GH-mediated ATRP preserves living character. Under UV illumination, LMCT is activated, producing polymers both at the desired interface and within the GH bulk. UV–Vis spectroscopy revealed active reduction of Cu(II) to Cu(I) along with concentration-dependent complex formation, indicating dynamic coordination chemistry within the hydrogel. The redox-active arginine- and glutamic acid-rich gelatin backbone coordinates and reduces the metal center, enabling ATRP at ppm-level catalyst concentrations. While polymerization proceeds in GH-Cu(II) reactors, adding external mobile ligands to the GH results in longer polymer brushes. Here, the results reported here are exploratory. More experiments are needed to characterize polymer brush growth in GHs and compare it to conventional surface-initiated polymerization in solution.

Absorption↗
NASA NTRS2001

Toward a Micro Gas Chromatograph/Mass Spectrometer (GC/MS) System

Miniature mass filters (e.g., quadrupoles, ion traps) have been the subject of several miniaturization efforts. A project is currently in progress at JPL to develop a miniaturized Gas Chromatograph/Mass Spectrometer (GC/MS) system, incorporating and/or developing miniature system components including turbomolecular pumps, scroll type roughing pump, quadrupole mass filter, gas chromatograph, precision power supply and other electronic components. The preponderance of the system elements will be fabricated using microelectromechanical systems (MEMS) techniques. The quadrupole mass filter will be fabricated using an X-ray lithography technique producing high precision, 5x5 arrays of quadrupoles with pole lengths of about 3 mm and a total volume of 27 cubic mm. The miniature scroll pump will also be fabricated using X-ray lithography producing arrays of scroll stages about 3 mm in diameter. The target detection range for the mass spectrometer is 1 to 300 atomic mass units (AMU) with are solution of 0.5 AMU. This resolution will allow isotopic characterization for geochronology, atmospheric studies and other science efforts dependant on the understanding of isotope ratios of chemical species. This paper will discuss the design approach, the current state-of-the art regarding the system components and the progress toward development of key elements. The full system is anticipated to be small enough in mass, volume and power consumption to allow in situ chemical analysis on highly miniaturized science craft for geochronology, atmospheric characterization and detection of life experiments applicable to outer planet roadmap missions.

Wiberg, D. V.↗
NASA NTRS2004

Integrating Carbon Nanotubes For Atomic Force Microscopy Imaging Applications

Carbon nanotube (CNT) related nanostructures possess remarkable electrical, mechanical, and thermal properties. To produce these nanostructures for real world applications, a large-scale controlled growth of carbon nanotubes is crucial for the integration and fabrication of nanodevices and nanosensors. We have taken the approach of integrating nanopatterning and nanomaterials synthesis with traditional silicon micro fabrication techniques. This integration requires a catalyst or nanomaterial protection scheme. In this paper, we report our recent work on fabricating wafer-scale carbon nanotube AFM cantilever probe tips. We will address the design and fabrication considerations in detail, and present the preliminary scanning probe test results. This work may serve as an example of rational design, fabrication, and integration of nanomaterials for advanced nanodevice and nanosensor applications.

Ye, Qi↗
DOE OSTI2024

Operando study of HfO 2 atomic layer deposition on partially hydroxylated Si(111)

The introduction of atomic layer deposition (ALD), to the microelectronics industry has introduced a large number of new possible materials able to be deposited in layers with atomic thickness control. One such material is the high-κ oxide HfO 2 ; thermally stable and ultrathin HfO 2 films deposited by ALD are a significant contender to replace SiO 2 as the gate oxide in capacitor applications. We present a mechanistic study of the first deposition cycle of HfO 2 on the Si(111) surface using tetrakis(dimethylamido) hafnium (TDMAHf) and water as precursors using operando ambient pressure x-ray photoelectron spectroscopy. Here, we show that the hydroxylation of the clean Si(111) surface by residual water vapor, resulting in a 0.3 monolayer coverage of hydroxyls, leads to instantaneous full surface coverage of TDMAHf. The change in the atomic ratio of Hf to C/N found during the first deposition half-cycle, however, does not match the assumed immediate ligand loss through reaction with surface hydroxyls. One would expect an immediate loss of ligands, indicated by a Hf:N ratio of approximately 1:3 as TDMAHf deposits onto the surface; however, a Hf:N ratio of 1:3.6 is observed. The partial hydroxylation on the Si(111) surface leads to binding through the TDMAHf ligand N atoms resulting in both N and CH 3 being found remaining on the surface post water half-cycle. Although there is evidence of ligand exchange reactions occurring at Si–OH sites, it also seems that N binding can occur on bare Si, highlighting the complexity of the substrate/precursor reaction even when hydroxyls are present. Moreover, the initial low coverage of Si–OH/Si–H appears to severely limit the amount of Hf deposited, which we hypothesize is due to the specific geometry of the initial arrangement of Si–OH/Si–H on the rest- and adatoms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Solar cell comprising a metal-oxide buffer layer and method of fabrication

A perovskite-based solar cell comprising a transparent electrode disposed on a buffer layer that protects the perovskite from damage during the deposition of the electrode is disclosed. The buffer material is deposited using either low-temperature atomic-layer deposition, chemical-vapor deposition, or pulsed chemical-vapor deposition. In some embodiments, the perovskite material is operative as an absorption layer in a multi-cell solar-cell structure. In some embodiments, the perovskite material is operative as an absorption layer in a single junction solar cell structure.

Bush, Kevin Alexander↗
DOE OSTI2024

Manufacturing ODS Steels from GARS Powders by Friction Consolidation and Extrusion

Previous research suggested that friction-based processing is a promising method for fabricating oxide dispersion-strengthened (ODS) steel. In this study, we combined friction consolidation and friction extrusion to successfully manufacture ODS steel rods using precursor powder made with gas atomization reaction synthesis. We examined the microstructure evolution from the initial powder to the final extruded rod, which revealed the dispersion process of Y. Additionally, by comparing the microstructures of three rods extruded at different temperatures, we showed that low-temperature friction extrusion effectively enhanced microstructure uniformity and prevented grain coarsening, leading to improved mechanical properties. Furthermore, our findings provide practical guidelines for adjusting processing parameters in the production of ODS steel using friction-based processing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhanced CO 2 Methanation Activity of Sm 0.25 Ce 0.75 O 2-δ –Ni by Modulating the Chelating Agents-to-Metal Cation Ratio and Tuning Metal–Support Interactions

Highly active and selective CO 2 methanation catalysts are critical to CO 2 upgrading, synthetic natural gas production, and CO 2 emission reduction. Wet impregnation is widely used to synthesize oxide-supported metallic nanoparticles as the catalyst for CO 2 methanation. However, as the reagents cannot be homogeneously mixed at an atomic level, it is challenging to modulate the microstructure, crystal structure, chemical composition, and electronic structure of catalysts via wet impregnation. In this work, a scalable and straightforward catalyst fabrication approach has been designed and validated to produce Sm 0.25 Ce 0.75 O 2-δ -supported Ni (SDC–Ni) as the CO 2 methanation catalyst. By varying the chelating agents-to-total metal cations ratio (C/I ratio) during the catalyst synthesis, we can readily and simultaneously modulate the microstructure, metallic surface area, crystal structure, chemical composition, and electronic structure of SDC–Ni, consequently fine-tuning the oxide–support interactions and CO 2 methanation activity. The optimal C/I ratio (0.1) leads to an SDC–Ni catalyst that facilitates C–O bond cleavage and significantly improves CO 2 conversion at 250 °C. A CO 2 -to-CH 4 yield of >73% has been achieved at 250 °C. Furthermore, a stable operation of >1500 hours has been demonstrated, and no degradation is observed. Extensive characterizations were performed to fundamentally understand how to tune and enhance CO 2 methanation activity of SDC–Ni by modulating the C/I ratio. The correlation of physical, chemical, and catalytic properties of SDC–Ni with the C/I ratio is established and thoroughly elaborated in this work. This study could be applied to tune the oxide–support interactions of various catalysts for enhancing the catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Progress on Design and Production of Oxide Dispersion–Strengthened Alumina-Forming Austenitic Alloys for Nuclear Applications

Alumina-forming austenitic (AFA) alloys are a promising class of nuclear materials due to their high-temperature oxidation/corrosion resistance and mechanical properties. Unfortunately, these alloys are limited in use for core material applications, specifically in their use as nuclear fuel cladding. Improving these alloys through a fine dispersion of oxide precipitates and thus increasing the effective irradiation sink strength of the alloy system may mitigate many of the degradation phenomena expected during alloy deployment (such as high-temperature helium embrittlement for lead-cooled fast reactor applications). This work package has started using a combination of conventional and advanced manufacturing approaches to the fabrication of oxide dispersion–strengthened (ODS) AFA materials. As such, this report summarizes progress to date in the fabrication of new compositions of these ODS AFA materials with a focus on reactor-specific design and a multifaceted manufacturing approach. Two different compositions of AFA gas-atomized powders were procured, and 200 g of each have been prepared using mechanical alloying with the expectation of high-temperature consolidation in Q1 of FY24. In addition, an approach to use reactive cover gases to promote additional precipitate formation has been developed for implementation in FY24 as a direct comparison with conventionally manufactured alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1993

Space Station WP-2 application of LDEF MLI results

The Cascaded Variable Conductance Heat Pipe Experiment, which was developed by Michael Grote of McDonnell Douglas Electronic Systems Company, was located in Tray F-9 of the Long Duration Exposure Facility (LDEF), where it received atomic oxygen almost normal to its surface. The majority of the tray was covered by aluminized Kapton polyimide multilayer insulation (MLI), which showed substantial changes from atomic oxygen erosion. Most of the outermost Kapton layer of the MLI and the polyester scrim cloth under it were lost, and there was evidence of contaminant deposition which discolored the edges of the MLI blanket. Micrometeoroid and orbital debris (MM/OD) hits caused small rips in the MLI layers, and in some cases left cloudy areas where the vapor plume caused by a hit condensed on the next layer. The MLI was bent gradually through 90 deg at the edges to enclose the experiment, and the Kapton that survived along the curved portion showed the effects of atomic oxygen erosion at oblique angles. In spite of space environment effects over the period of the LDEF mission, the MLI blanket remained functional. The results of the analysis of LDEF MLI were used in developing the standard MLI blanket for Space Station Work Package-2 (WP-2). This blanket is expected to last 30 years when exposed to the low Earth orbit (LEO) environment constituents of atomic oxygen and MM/OD, which are the most damaging to MLI materials. The WP-2 standard blanket consists of an outer cover made from Beta-cloth glass fiber fabric which is aluminized on the interior surface, and an inner cover of 0.076-mm (0.003-in) double-side-aluminized perforated Kapton. The inner reflector layers are 0.0076-mm (0.0003-in) double-side aluminized, perforated Kapton separated by layers of Dacron polyester fabric. The outer cover was selected to be resistant to the LEO environment and durable enough to survive in orbit for 30 years. This paper describes the analyses of the LDEF MLI results, and how these results contributed to the selection of the WP-2 MLI blanket materials and configuration.

Smith, Charles A.↗
NASA NTRS2005

Atomic Oxygen Treatment and Its Effect on a Variety of Artist's Media

Atomic oxygen treatment has been investigated as an unconventional option for art restoration where conventional methods have not been effective. Exposure of surfaces to atomic oxygen was first performed to investigate the durability of materials in the low Earth orbit environment of space. The use of the ground based environmental simulation chambers, developed for atomic oxygen exposure testing, has been investigated in collaboration with conservators at a variety of institutions, as a method to clean the surfaces of works of art. The atomic oxygen treatment technique has been evaluated as a method to remove soot and char from the surface of oil paint (both varnished and unvarnished), watercolors, acrylic paint, and fabric as well as the removal of graffiti and other marks from surfaces which are too porous to lend themselves to conventional solvent removal techniques. This paper will discuss the treatment of these surfaces giving an example of each and a discussion of the treatment results.

Miller, Sharon K. R.↗
NASA NTRS2018

Determination of Trace Silicone Contamination on Composites by Quantitative XPS and LIBS

Surface treatment and surface characterization techniques are critical to ensure that adherends are chemically activated and free of contaminants prior to adhesive bonding. Silicone contamination from mold-release agents and other sources can interfere with interfacial bonding, decreasing the durability and performance of bonded composite structures. Tools and methods are needed that can be used in a production environment to reliably detect low levels of contaminants in a rapid, simple, and cost-effective manner to improve bond reliability. In this work, surface characterization of carbon fiber reinforced polymer (CFRP) composites was performed using laser induced breakdown spectroscopy (LIBS) and the results were compared with those obtained from X-ray photoelectron spectroscopy (XPS). The objective was to investigate the ability to quantify the surface species measured by LIBS since it offers many advantages over XPS in terms of ease of use, sample preparation, and real-time results. The as-processed CFRP panels had trace surface silicone contamination from the fabrication process, the source of which was not investigated. The composites were laser treated at select average laser power levels, resulting in varying levels of contamination reduction. The Si atomic percentage measurements using XPS were conducted both before and after laser ablation. The XPS results were compared with those obtained from LIBS to assess the reliability of each technique for surface contaminant characterization. The results showed an excellent correlation in Si atomic concentration between the two techniques.

Ledesma, Rodolfo↗
DOE OSTI2022

Conversion of Classical Light Emission from a Nanoparticle‐Strained WSe 2 Monolayer into Quantum Light Emission via Electron Beam Irradiation

Abstract Solid‐state single photon emitters (SPEs) within atomically thin transition metal dichalcogenides (TMDs) have recently attracted interest as scalable quantum light sources for quantum photonic technologies. Among TMDs, WSe 2 monolayers (MLs) are promising for the deterministic fabrication and engineering of SPEs using local strain fields. The ability to reliably produce isolatable SPEs in WSe 2 is currently impeded by the presence of numerous spectrally overlapping states that occur at strained locations. Here nanoparticle (NP) arrays with precisely defined positions and sizes are employed to deterministically create strain fields in WSe 2 MLs, thus enabling the systematic investigation and control of SPE formation. Using this platform, electron beam irradiation at NP‐strained locations transforms spectrally overlapped sub‐bandgap emission states into isolatable, anti‐bunched quantum emitters. The dependence of the emission spectra of WSe 2 MLs as a function of strain magnitude and exposure time to electron beam irradiation is quantified and provides insight into the mechanism for SPE production. Excitons selectively funnel through strongly coupled sub‐bandgap states introduced by electron beam irradiation, which suppresses spectrally overlapping emission pathways and leads to measurable anti‐bunched behavior. The findings provide a strategy to generate isolatable SPEs in 2D materials with a well‐defined energy range.

2D material↗
DOE OSTI2020

Protected helical transport in magnetically doped quantum wires: Beyond the one-dimensional paradigm

One-dimensional (1D) quantum wires, which are functionalized by magnetic ad-atoms, can host ballistic helical transport. Helicity protects transport from an undesirable influence of material imperfections and makes the magnetically doped wire very promising elements for nanoelectronics and spintronics. However, fabricating purely 1D conductors is experimentally very challenging and not always feasible. In this paper, we show that the protected helical transport can exist even inquasi-1D wires. We model the quasi-1D magnetically doped wire as two coupled dense 1D Kondo chains. Each chain consists of itinerant electrons interacting with localized quantum magnetic moments - Kondo impurities. We have analyzed the regimes of weak-, intermediate- and strong inter-chain coupling and found conditions necessary for the origin of the aforementioned protected transport. Our results give a push for experimental realizations of the helical states in magnetically doped wires.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1994

Analytical and experimental studies of impinging liquid jets

Impinging injectors are a common type of injector used in liquid propellant rocket engines and are typically used in engines where both propellants are injected as a liquid, e.g., engines using LOX/hydrocarbon and storable propellant combinations. The present research program is focused on providing the requisite fundamental understanding associated with impinging jet injectors for the development of an advanced a priori combustion stability design analysis capability. To date, a systematic study of the atomization characteristics of impinging liquid jets under cold-flow conditions have been completed. Effects of orifice diameter, impingement angle, pre-impingement length, orifice length-to-diameter ratio, fabrication procedure, jet flow condition and jet velocity under steady and oscillating, and atmospheric- and high-pressure environments have been investigated. Results of these experimental studies have been compared to current models of sheet breakup and drop formation. In addition, the research findings have been scrutinized to provide a fundamental explanation for a proven empirical correlation used in the design of stable impinging injector-based rocket engines.

Ryan, H. M.↗
DOE OSTI2023

Bimolecular Reaction Mechanism in the Amido Complex-Based Atomic Layer Deposition of HfO 2

The surface chemistry of the initial growth during the first or first few precursor cycles in atomic layer deposition is decisive for how the growth proceeds later on and thus for the quality of the thin films grown. Yet, although general schemes of the surface chemistry of atomic layer deposition have been developed for many processes and precursors, in many cases, knowledge of this surface chemistry remains far from complete. For the particular case of HfO 2 atomic layer deposition on a SiO 2 surface from an alkylamido-hafnium precursor and water, we address this lack by carrying out an operando atomic layer deposition experiment during the first cycle of atomic layer deposition. Ambient-pressure X-ray photoelectron spectroscopy and density functional theory together show that the decomposition of the metal precursor on the stoichiometric SiO 2 surface in the first half-cycle of atomic layer deposition proceeds via a bimolecular reaction mechanism. The reaction leads to the formation of Hf-bonded methyl methylene imine and free dimethylamine. In addition, ligand exchange takes place involving the surface hydroxyls adsorbed at defect sites of the SiO 2 surface.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Anatase TiO 2 Surface Hydration: Infrared Vibrational Assignment and Facet-Specific Stability

Anatase TiO 2 nanoparticles support a subtle diversity of surface aqua and hydroxy coordination environments that are characteristic of distinct facets and defect sites. The disparate properties and stability of each molecularly or dissociatively absorbed water environment may provide unique reactivity for facet- and site-selective atomic layer deposition (ALD). Here we probe the temperature-dependent and facet-specific stretching frequency and stability of surface hydroxyls on faceted anatase TiO 2 nanoparticles via in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Well-defined truncated octahedra, disks, and rods fabricated through hydrothermal synthesis present dominant (101), (001), and (010) facets, respectively. The selective dehydration of discrete local coordination environments as a function of temperature provides a potential pathway to site-selective and facet-selective ALD on metal oxide nanomaterials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗