Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Manganese-rich high entropy oxides for lithium-ion batteries:materials design approaches to address voltage fade

Lithium- and manganese-rich oxides are of interest as lithium-ion battery cathode materials as Mn is earth abundant, low cost, and can deliver high capacity. Herein, a high entropy strategy was used to prepare Mn rich high entropy oxide (HEO) materials by including four additional metals (Ni, Co, Fe and Al) in the compositions using a mild co-precipitation method. Two HEOs (Li x Ni 0.1 Mn 0.6 Co 0.1 Al 0.1 Fe 0.1 O y , where x = 1.5 for HEO-L and x = 0.5 for HEO-H) with layered and spinel-layered hybrid structures were investigated where the morphology, elemental composition, structure, atomic level phase distribution, and electrochemistry were determined. The HEO-L samples involve a Li 2 TMO 3 layered structure with ~39% stacking faults. HEO-H is a hybrid structure comprised of 80 wt% spinel and 20 wt% LiMO 2 layered structure. The high entropy manganese-rich HEO-L showed higher capacity and 93% retention of the average voltage after 100 cycles while HEO-H showed higher capacity retention and near 100% average voltage retention. Finally, operando X-ray absorption spectroscopy revealed that the Ni, Co, and Mn are redox active in both materials while the Fe center remains at the Fe 3+ oxidation state throughout cycling, where the changes in the oxidation states for both materials during discharge were consistent with the delivered electrochemical capacity rationalizing the observed electrochemistry.

25 ENERGY STORAGE↗
DOE OSTI2020

Enabling high areal capacity for Co-free high voltage spinel materials in next-generation Li-ion batteries

The rapidly growing technological demand for lithium-ion batteries has prompted the development of novel cathode materials with high energy density, low cost, and improved safety. High voltage spinel, LiNi 0.5 Mn 1.5 O 4 (LNMO), is one of the most promising candidates yet to be commercialized. The two primary obstacles for this material are the inferior electronic conductivity and fast capacity degradation in full cells due to the high operating voltage. By systematically addressing these limitations, we successfully develop a thick LNMO electrode with areal capacity loadings up to 3 mAh·cm –2 . The optimized thick electrode is paired with a commercial graphite anode at both the coin cell and pouch cell level, achieving a full cell capacity retention as high as 72% and 78%, respectively, after 300 cycles. We attribute this superior cycling stability to careful optimizations of cell components and testing conditions, with a specific focus improving electronic conductivity and high voltage compatibility. These results suggest precise control of materials quality, electrode architecture and electrolyte optimization can soon support the development of a cobalt-free battery system based on a thick LNMO cathode (>4 mAh·cm 2 ), which will eventually meet the needs of next-generation Li-ion batteries with reduced cost, improved safety, and assured sustainability.

25 ENERGY STORAGE↗
DOE OSTI2024

In Situ Insights into Cathode Calcination for Predictive Synthesis: Kinetic Crystallization of LiNiO 2 from Hydroxides

Abstract Calcination is a solid‐state synthesis process widely deployed in battery cathode manufacturing. However, its inherent complexity associated with elusive intermediates hinders the predictive synthesis of high‐performance cathode materials. Here, correlative in situ X‐ray absorption/scattering spectroscopy is used to investigate the calcination of nickel‐based cathodes, focusing specifically on the archetypal LiNiO 2 from Ni(OH) 2 . Combining in situ observation with data‐driven analysis reveals concurrent lithiation and dehydration of Ni(OH) 2 and consequently, the low‐temperature crystallization of layered LiNiO 2 alongside lithiated rocksalts. Following early nucleation, LiNiO 2 undergoes sluggish crystallization and structural ordering while depleting rocksalts; ultimately, it turns into a structurally‐ordered layered phase upon full lithiation but remains small in size. Subsequent high‐temperature sintering induces rapid crystal growth, accompanied by undesired delithiation and structural degradation. These observations are further corroborated by mesoscale modeling, emphasizing that, even though calcination is thermally driven and favors transformation towards thermodynamically equilibrium phases, the actual phase propagation and crystallization can be kinetically tuned via lithiation, providing freedom for structural and morphological control during cathode calcination.

36 MATERIALS SCIENCE↗
DOE OSTI2024

4 V Na Solid State Batteries Enabled by a Scalable Sodium Metal Oxyhalide Solid Electrolyte

All-solid-state sodium batteries (ASSSBs) are viable candidates for large scale energy storage that could vie with lithium. Ductile solid catholytes for such cells that can be prepared without extensive ball milling and directly paired with high voltage sodium cathodes are lacking, however. We report a new amorphous fast Na-ion conducting metal oxychloride that meets these criteria, synthesized through a scalable and low-cost route based on a spontaneous solid-state reaction with simple short mixing and 100 °C annealing. It has an ionic conductivity of 1.2 mS·cm–1 and low activation energy of 0.31 eV. Due to its dual O2–/Cl– framework, it exhibits a high anodic potential of 4 V vs Na+/Na and good chemical/electrochemical compatibility with high voltage sodium cathode materials. ASSSBs consisting of the oxychloride solid electrolyte paired with a high voltage P2–Na2/3Ni1/3Mn2/3O2 cathode showed stable long-term cycling with a 4.0 V vs Na3Sn cutoff potential and even to 4.3 V.

solid-state electrolyte, solid-state batteries, Nu↗
DOE OSTI2022

Super-resolving microscopy images of Li-ion electrodes for fine-feature quantification using generative adversarial networks

Abstract For a deeper understanding of the functional behavior of energy materials, it is necessary to investigate their microstructure, e.g., via imaging techniques like scanning electron microscopy (SEM). However, active materials are often heterogeneous, necessitating quantification of features over large volumes to achieve representativity which often requires reduced resolution for large fields of view. Cracks within Li-ion electrode particles are an example of fine features, representative quantification of which requires large volumes of tens of particles. To overcome the trade-off between the imaged volume of the material and the resolution achieved, we deploy generative adversarial networks (GAN), namely SRGANs, to super-resolve SEM images of cracked cathode materials. A quantitative analysis indicates that SRGANs outperform various other networks for crack detection within aged cathode particles. This makes GANs viable for performing super-resolution on microscopy images for mitigating the trade-off between resolution and field of view, thus enabling representative quantification of fine features.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Phase Stability and Kinetics of Topotactic Dual Ca 2+ –Na + Ion Electrochemistry in NaSICON NaV 2 (PO 4 ) 3

Recent reports of reversible calcium plating and stripping have rekindled interest in the development of Ca-ion batteries (CIBs) as next-generation energy storage devices. This technology has the potential to overcome the limitations of conventional Li-ion batteries, but CIBs are plagued by a paucity of suitable cathode materials. To date, NaSICON-structured NaV 2 (PO 4 ) 3 has been demonstrated as a successful cathode candidate, exhibiting reversible (de)intercalation of 0.6 mol Ca 2+ along with stable cycling performance. However, a complex multiphase mixture forms on discharge so the Ca-ion charge storage mechanism in the NaSICON framework is poorly understood. Here in this work, we report on an investigation of the structure and/or Na + /Ca 2+ environment(s) of a variety of chemically prepared NaSICON Ca x Na y V 2 (PO 4 ) 3 phases which were characterized using synchrotron XRD, SEM-EDS, 23 Na NMR, and TEM. Highly calciated CaV 2 (PO 4 ) 3 , Ca 1.5 V 2 (PO 4 ) 3 , and CaNaV 2 (PO 4 ) 3 phases can be prepared at high temperature, but -unlike Ca 0.6 NaV 2 (PO 4 ) 3 -these materials are electrochemically inactive. To better understand the fundamental factors impacting successful Ca 2+ electrochemistry in this system, DFT was employed to examine the Ca x Na y V 2 (PO 4 ) 3 phase diagram and Ca 2+ diffusion mechanism. Theoretical insights show that phase separation into Na-rich and Ca-rich phases is a reason for the capacity limitation and demonstrate that Na + ions in the host materials assist the migration of neighboring Ca 2+ ions, enabling reversible electrochemistry in Ca x Na y V 2 (PO 4 ) 3 . This investigation of fundamental principles affecting reversible Ca 2+ (de)intercalation in Ca x Na y V 2 (PO 4 ) 3 allows for the development of design principles to enable the discovery of a variety of successful cathodes for CIBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

In situ inorganic conductive network formation in high-voltage single-crystal Ni-rich cathodes

High nickel content in LiNi x Co y Mn z O 2 (NCM, x ≥ 0.8, x + y + z = 1) layered cathode material allows high specific energy density in lithium-ion batteries (LIBs). However, Ni-rich NCM cathodes suffer from performance degradation, mechanical and structural instability upon prolonged cell cycling. Although the use of single-crystal Ni-rich NCM can mitigate these drawbacks, the ion-diffusion in large single-crystal particles hamper its rate capability. Herein, we report a strategy to construct an in situ Li 1.4 Y 0.4 Ti 1.6 (PO 4 ) 3 (LYTP) ion/electron conductive network which interconnects single-crystal LiNi 0.88 Co 0.09 Mn 0.03 O 2 (SC-NCM88) particles. The LYTP network facilitates the lithium-ion transport between SC-NCM88 particles, mitigates mechanical instability and prevents detrimental crystalline phase transformation. When used in combination with a Li metal anode, the LYTP-containing SC-NCM88-based cathode enables a coin cell capacity of 130 mAh g -1 after 500 cycles at 5 C rate in the 2.75-4.4 V range at 25 °C. Tests in Li-ion pouch cell configuration (i.e., graphite used as negative electrode active material) demonstrate capacity retention of 85% after 1000 cycles at 0.5 C in the 2.75-4.4 V range at 25 °C for the LYTP-containing SC-NCM88-based positive electrode.

25 ENERGY STORAGE↗
DOE OSTI2025

Chemo-Mechanical Behavior and Stability of High-Loading Cathodes in Solid-State Batteries

Solid-state batteries can offer higher energy density and improved safety compared to lithium ion batteries, which use flammable liquid electrolytes. Increasing the ratio of cathode active materials in composite cathodes enhances the energy density and reduces manufacturing costs. Changes in the ratio of cathode active materials alter the microstructure and chemo-mechanical response of a cathode during operation. Understanding the relationship between composition, microstructure, and chemo-mechanical interactions is critical for optimizing solid-state cathodes. Here, in this study, we engineered composite cathodes with varying ratios of LiNi 0.8 Co 0.1 Mn 0.1 O 2 and Li 6 PS 5 Cl to systematically investigate the role of microstructural evolution in long-term chemo-mechanical transformations. Chemo-mechanical stresses resulting from the volume changes of the cathode active materials led to degradation mechanisms, such as fracture and interfacial delamination. Active material fracture and delamination led to underutilization of active material and significant capacity decay during cycling. Coatings that suppress active material-active material interactions during cycling may aid in suppressing the generation of local stress hotspots.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding intercalation chemistry for sustainable aqueous zinc–manganese dioxide batteries

Rechargeable aqueous Zn-MnO 2 technology combines one of the oldest battery chemistries with favourable sustainability characteristics, including safety, cost and environmental compatibility. However, the ambiguous charge storage mechanism presents a challenge to fulfil the great potential of this energy technology. In this work, we leverage on advanced electron microscopy, electrochemical analysis and theoretical calculations to look into the intercalation chemistry within the cathode material, or α-MnO 2 more specifically. We show that Zn 2+ insertion into the cathode is unlikely in the aqueous system; rather, the charge storage process is dominated by proton intercalation to form α-H x MnO 2 . We further reveal anisotropic lattice change as a result of entering protons proceeding from the surface into the bulk of α-MnO 2 , which accounts for the structural failure and capacity decay of the electrode upon cycling. Our work not only advances the fundamental understanding of rechargeable zinc batteries but also suggests the possibility to optimize proton intercalation kinetics for better-performing cell designs. A rechargeable aqueous Zn-MnO 2 battery features a combination of favourable sustainability characteristics from safety to cost. The authors deploy advanced characterizations and theoretical calculations to provide fresh insight into the charge storage mechanism, which not only closes an ongoing debate but suggests ways forward.

25 ENERGY STORAGE↗
DOE OSTI2024

Isothermal Microcalorimetry Analysis of Li/ β -MnO 2 Discharge

Despite widespread use over several decades, the lithium/manganese dioxide (Li/MnO 2 ) discharge mechanism is not completely understood owing to the structural complexity of the material. However, an improved understanding could lead to broader adoption as a primary and even secondary cathode material. Here, we examine the discharge of single-phaseβ-MnO 2 using isothermal microcalorimetry for the first time. Equilibrium voltage and entropy changes are characterized over the entire discharge range and used to rationalize the results. These measurements are supplemented by electrochemical impedance and X-ray diffraction data that give the clearest picture of theβ-MnO 2 lithiation process to date. We find that the first half of discharge is dominated by a two-phase reaction to form Li 0.5 MnO 2 followed by single-phase insertion to a composition of Li 1.0 MnO 2 , which confirms prior first-principles calculations. The tetragonalβ-MnO 2 lattice undergoes asymmetric expansion from Jahn-Teller distorted Mn 3+ to form an orthorhombic LiMnO 2 phase which retains the 1 × 1 tunnel structure. Microcalorimetry results suggest the presence of parasitic reactions occurring during the second half of discharge, which could arise from decomposition of electrolyte or release and reaction of residual water retained in the structure.

Electrochemistry↗
DOE OSTI2022

Transition Metal Oxide Powders Made from Flame Spray Pyrolysis for Li-Ion Batteries

In 2012 the U.S. Department of Energy introduced its EV Everywhere Grand Challenge, with a stated goal of enabling “plug-in electric vehicles (PEVs) that are as affordable and convenient for the American family as gasoline-powered vehicles by 2022.” This requires a reduction in battery costs from the current $500/kWh to around $125/kWh. Most approaches have been to eliminate vehicle weight through lightweighting and to improve the energy density of battery materials. But what if we were able to just make the materials cheaper instead? To this end we introduce a green, low-cost method of producing cathode materials using an integrated flame spray pyrolysis process.

25 ENERGY STORAGE↗
DOE OSTI2024

Synthetic methods for crystallite size control of bimetallic polyanionic battery compositions

Bimetallic polyanionic materials, such as silver vanadium phosphorus oxide (Ag 2 VO 2 PO 4 , SVOP), are promising cathode materials for Li batteries due in part to their large capacity and high current capability. A new synthesis of Ag 2 VO 2 PO 4 based on microwave heating is disclosed, where the reaction time is reduced by approximately 100 times relative to other reported methods, and the crystallite size is controlled via synthesis temperature, showing a linear positive correlation of crystallite size with temperature. Reaction times of an hour or less are sufficient to render phase-pure material after reaction at 50° C. to 180° C., significantly lower than the temperatures reported for other methods. Crystallite sizes between 42 nm and 60 nm are achieved by the novel method, smaller than by other methods. Silver/vanadium atomic ratios of 1.96 to 2.04 in the as-synthesized SVOP result and appear temperature-dependent. Notably, under galvanostatic reduction, the Ag 2 VO 2 PO 4 sample with the smallest crystallite size delivers the highest capacity and shows the highest loaded voltage.

Takeuchi, Kenneth J.↗
DOE OSTI2020

Synthesis of LiNiO 2 at Moderate Oxygen Pressure and Long-Term Cyclability in Lithium-Ion Full Cells

The widespread adoption of electric vehicles necessitates higher-energy-density and longer-life cathode materials for Li-ion batteries. LiNiO 2 offers a higher energy density at a lower cost than other high-Ni-content cathodes containing additional transition-metal ions. However, detrimental phase transformations and impedance growth, resulting from structural defects formed during synthesis, lead to poor cyclability and limit the practical viability of LiNiO 2 . Herein, we demonstrate a considerably improved cycle life for LiNiO 2 by synthesizing it under a pressurized oxygen environment. The capacity retention in pouch-type full cells with a graphite anode after 1000 cycles is increased from 59 to 76% by applying a mere 1.7 atm of oxygen pressure during the synthesis of LiNiO 2 . With iodometric titration and inductively coupled plasma optical emission spectroscopy analysis, we provide clear evidence that oxygen pressure during synthesis reduces the occurrence of lattice oxygen vacancies and increases the content of Ni 3+ in LiNiO 2 , improving its structural integrity and cyclability. Post-mortem analysis of the cycled cathodes provides insights into the sources of degradation occurring during long-term cycling. Here, this work demonstrates a practically viable, synthetic approach combined with doping and coating to achieve improved performance with high-Ni layered oxide materials. Furthermore, this work represents the first report of extended cycling of LiNiO 2 in pouch full cells with graphite anode and will, therefore, serves as an important benchmark for future research on LiNiO 2 .

25 ENERGY STORAGE↗
DOE OSTI2021

Selective dopant segregation modulates mesoscale reaction kinetics in layered transition metal oxide

Incorporation of foreign elements into the cathode material is broadly adopted by both academia and industry to improve the battery performance. The lack of an in-depth understanding for the underlying mechanism, however, makes it a largely try-and-error process with unsatisfactory efficiency and effectiveness. This is particularly true for the electrochemical reaction kinetics that is heterogeneous over a broad range of length scales and is determined collectively by the cathode’s electronic structure, lattice configuration, and micro-morphology. In this work, we unveiled a facet-dependent dopant segregation effect in Zr-modified single-crystal LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode. By forming kinetically favored corners on the cathode particles, the presence of a trace amount of Zr critically modulates the mesoscale reaction kinetics. Our findings suggest that a delicately controlled dopant distribution is a viable strategy for designing the next-generation battery cathode with superior structural and chemical robustness.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Heuristics for Molten-Salt Synthesis of Single-Crystalline Ultrahigh-Nickel Layered Oxide Cathodes

In pursuit of Li-ion batteries with higher energy density, ultrahigh-nickel layered oxides are a leading candidate for next-generation cathode materials. Single-crystalline morphology offers a neat solution to the poor stability of ultrahigh-Ni cathodes; a lower active surface area mitigates electrolyte decomposition at high voltages, and the elimination of grain boundaries improves mechanical resilience and increases volumetric energy density. However, single-crystal cathodes possess their own challenges, several of which originate from synthesis at elevated temperatures meant to induce grain growth. Molten-salt synthesis is an alternative method for obtaining single crystals, accelerating grain growth through the presence of a molten flux without the need for increased temperature. Herein, we offer heuristic guidelines for molten-salt synthesis, discussing key factors for designing reaction mixtures and the necessary exploratory research for novel molten salt/cathode systems. Here, the influence of different salts and synthesis conditions on the morphology and properties of single-crystal LiNiO 2 is presented. It is found that oxidative salts, such as Li 2 O 2 and LiNO 3 , are crucial to supplementing dissolution of gaseous oxygen into the molten phase. Through these discussions, this work aims to provide a set of overarching principles for obtaining higher-quality single-crystal layered oxide cathodes and engender more rigorous and impactful investigation into their fundamental nature and applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Renewable Solvents to Replace Water in the Synthesis of Battery Materials

Our lab has been engaged in using glycerol to replace water in the synthesis of metal oxides, especially those for use in Li-ion battery. Glycerol is a byproduct from biodiesel production. The U.S. biodiesel manufacturers generate about 1 billion pounds of glycerol yearly, which needs to be utilized for producing value added products. By using glycerol as a solvent, we found that it can replace water to prepare many metal oxide powders. The materials synthesis processes have the potential to significantly reduce manufacturing cost and alleviate the environmental issues with aqueous processes. In this talk, I will present some of our work in materials synthesis using glycerol as a solvent. In particular, I will introduce the work on making active cathode materials for the Li-ion battery.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct evidence of low work function on SrVO 3 cathode using thermionic electron emission microscopy and high-field ultraviolet photoemission spectroscopy

Perovskite SrVO 3 has recently been proposed as a novel electron emission cathode material. Density functional theory (DFT) calculations suggest multiple low work function surfaces, and recent experimental efforts have consistently demonstrated effective work functions of ~2.7 eV for polycrystalline samples, both results suggesting, but not directly confirming, that some fraction of even lower work function surface is present. In this work, thermionic electron emission microscopy (ThEEM) and high-field ultraviolet photoemission spectroscopy (UPS) are used to study the local work function distribution and measure the work function of a partially oriented- (110)-SrVO 3 perovskite oxide cathode surface. Our results show direct evidence of low work function patches of about 2.0 eV on the cathode surface, with a corresponding onset of observable thermionic emission at 750 °C. We hypothesize that, in our ThEEM and UPS experiments, the high applied electric field suppresses the patch field effect, enabling the direct measurement of local work functions. This measured work function of 2.0 eV is comparable to the previous DFT-calculated work function values of the SrVO-terminated (110) SrVO 3 surface (2.3 eV) and SrO-terminated (100) surface (1.9 eV). The measured 2.0 eV value is also much lower than the work function for the (001) LaB 6 single crystal cathode (~2.7 eV) and comparable to the effective work function of B-type dispenser cathodes (~2.1 eV). If SrVO 3 thermionic emitters can be engineered to access domains of this low 2.0 eV work function, they have the potential to significantly improve thermionic emitter-based technologies.

36 MATERIALS SCIENCE↗