Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Structural and Electrochemical Characterization of Thin Film Li 2 MoO 3 Electrodes

We report that Li 2 MoO 3 is a promising structural stabilizing unit for use in composite layered-layered cathodes for Li-ion batteries. To enable the rational design of such cathodes, studies on fundamental phenomena related to the active material structure and electrode/electrolyte interface are needed. The present work details the fabrication and characterization of thin film Li 2 MoO 3 cathodes and shows that their electrochemical performance greatly depends on the nature of the cathode/electrolyte interface. The Li 2 MoO 3 thin films exhibit poor cyclability in a liquid carbonate electrolyte (e.g., initial capacity of 166 mAh/g with 40% capacity fade over 20 cycles) whereas all-solid-state Li 2 MoO 3 /Lipon/Li batteries show negligible fade during cycling. A suite of characterization methods including Raman spectroscopy and X-ray photoelectron spectroscopy are used to study the evolution of the cathode structure and cathode electrolyte interphase (CEI) layer during charge/discharge cycling. Li transport rates are another important factor which affect cathode performance. AC impedance spectroscopy studies reveal that the Li diffusion coefficient (D Li ) in Li 2 MoO 3 decreases from 4.36 × 10 -11 cm 2 /s in the fully discharged state to 4.51 × 10 -13 cm 2 /s when charged to 3.6 V vs. Li/Li + . In conclusion, the results presented herein provide insight on the fundamental phenomena which govern Li 2 MoO 3 cathode performance.

25 ENERGY STORAGE↗

Composite Ionogel Electrodes for Polymeric Solid-State Li-Ion Batteries

Realizing rechargeable cells with practical energy and power density requires electrodes with high active material loading, a remaining challenge for solid-state batteries. Here, we present a new strategy based on ionogel-derived solid-state electrolytes (SSEs) to form composite electrodes that enable high active material loading (>10 mg/cm 2 , ~9 mA/cm 2 at 1C) in a scalable approach for fabricating Li-ion cells. By tuning the precursor and active materials composition incorporated into the composite lithium titanate electrodes, we achieve near-theoretical capacity utilization at C/5 rates and cells capable of stable cycling at 5.85 mA/cm 2 (11.70 A/g) with over 99% average Coulombic efficiency at room temperature. Finally, we demonstrate a complete polymeric solid-state cell with a composite anode and a composite lithium iron phosphate cathode with ionogel SSEs, which is capable of stable cycling at a 1C rate.

25 ENERGY STORAGE↗

Superconductivity in thin films of the Mo-Re system.

A series of Mo-Re alloy films has been prepared by sputtering from a composite molybdenum and rhenium cathode. These films were deposited in an ultra-high purity environment onto sapphire substrates which were held at temperatures ranging from 400 to 1300 C. Maximum transition temperatures observed were 15 K which is significantly greater than the highest reported bulk values. Critical current and field characteristics also were found to be considerably greater in the films compared to corresponding bulk samples. Upper critical fields of over 100 kOe were measured. These enhanced properties are discussed in relation to the structural characteristics of the sputtered films.

Gavaler, J. R.↗

Design of a safe cylindrical lithium/thionyl chloride cell

Cell design criteria were established which can result in a safe lithium/thionyl chloride cell. A cell vent, a low area internal anode cell, cell balance and composition of the cathode-electrolyte solution were found to be important factors in the design of a safe cell. In addition to routine testing, both undischarged and discharged cells were subjected to electrical abuse, environmental abuse and mechanical abuse without disassembly.

Johnson, D. H.↗

Carbon dioxide electrolysis with solid oxide electrolyte cells for oxygen recovery in life support systems

The direct electrochemical reduction of carbon dioxide (CO2) is achieved without catalysts and at sufficiently high temperatures to avoid carbon formation. The tubular electrolysis cell consists of thin layers of anode, electrolyte, cathode and cell interconnection. The electrolyte is made from yttria-stabilized zirconia which is an oxygen ion conductor at elevated temperatures. Anode and cell interconnection materials are complex oxides and are electronic conductors. The cathode material is a composite metal-ceramic structure. Cell performance characteristics have been determined using varying feed gas compositions and degrees of electrochemical decomposition. Cell test data are used to project the performance of a three-person CO2-electrolysis breadboard system.

Isenberg, Arnold O.↗

Fabricating Solid-State Batteries for Electric Aviation

All-solid-state lithium batteries are widely reputed as the next major step in energy storage technology on account their drastically improved safety over wet cells, as solid electrolytes lack the volatile compounds in wet electrolytes that make them combustible. This enhanced safety enables a far wider range of products and vehicles to go fully electric and aligns with future NASA missions that require high performing, reliable, and safe batteries. However, they currently face issues with implementation in consumer products due to the often-poor mechanical properties of the solid electrolyte and relative difficulty to manufacture. Typical solid-state electrolyte challenges were bypassed by incorporating a range of polymeric binders into a solid electrolyte suspension and cast onto a composite carbon-sulfide cathode to create a single bilayer film. The resulting films display superior flexibility and durability compared to solid-electrolyte films typically discussed in literature without compromising the thinness of the films. The bilayer film was then punched into 12.7 cm diameter discs and 4 cm by 5 cm sheets, pressed, and assembled into coin cells and pouch cells respectively.

Batteries↗

Stabilized birnessite cathode for high power and high energy density applications

A battery comprises a housing, an electrolyte disposed in the housing, an anode disposed in the housing, a stabilized cathode disposed in the housing and comprising a cathode material. The cathode material comprises a composition selected from birnessite or layered-polymorph of manganese dioxide (δ-MnO2), the composition being stabilized by bismuth and copper ions, a conductive carbon, and a binder. The anode can be at least 50% (m/m) lithium, magnesium, aluminum, or zinc.

Yadav, Gautam G.↗

Low cobalt layered oxide materials for lithium ion battery electrodes

Stabilized layered lithium metal oxide cathode materials are described which include excess lithium, Ni, Mn, and at least one other metal ion. The materials comprise a layered LiMO 2 -type material in which M comprises a combination of Ni, Mn, and at least one other metal ion that includes less than about 6 mol % Co; and which has about 1 to 6 percent excess lithium. In one embodiment, the stabilized lithium metal oxide cathode material comprises a composition having the empirical formula xLi 2 MnO 3 ·(1−x)LiNi 0.5+δ/2 Mn 0.5−δ Co δ/2 O 2 , wherein 0 1+3y [Ni a Mn b M′ c ] 1−y O 2 , wherein M′ is one of more metal selected from the group consisting of Co, Al, Fe, Mg, and Ti; 0<y≤0.02; 0.85≤a≤0.96; 0.03≤b≤0.1; and 0.01≤c≤0.1.

Croy, Jason R.↗

Electronic structure and conductivity of nanocomposite metal (Au,Ag,Cu,Mo)-containing amorphous carbon films

In this work, we study the influence of the incorporation of different metals (Me = Au, Ag, Cu, Mo) on the electronic structure of amorphous carbon (a-C:Me) films. The films were produced at room temperature using a novel pulsed dual-cathode arc deposition technique. Compositional analysis was performed with secondary neutral mass spectroscopy whereas X-ray diffraction was used to identify the formation of metal nanoclusters in the carbon matrix. The metal content incorporated in the nanocomposite films induces a drastic increase in the conductivity, in parallel with a decrease in the band gap corrected from Urbach energy. The electronic structure as a function of the Me content has been monitored by x-ray absorption near edge structure (XANES) at the C K-edge. XANES showed that the C host matrix has a dominant graphitic character and that it is not affected significantly by the incorporation of metal impurities, except for the case of Mo, where the modifications in the lineshape spectra indicated the formation of a carbide phase. Subtle modifications of the spectral lineshape are discussed in terms of nanocomposite formation.

36 MATERIALS SCIENCE↗

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb2O3 from carbon coated Sb2O3 nanoparticles can accommodate the Sb swelling upon sodiation and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~554 mAh•g-1, good rate capability (315 mhA•g-1 at 10C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na0.9[Cu0.22Fe0.30Mn0.48]O2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~130 Wh•kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0-4.0 V, ~1.5 times energy of full-cells with similar design using hard carbon anodes.

Song, Junhua↗

Ni nanoparticles embedded into cross-linked NiO nanoflakes as enhanced cathode for alkaline batteries

Highlights: • Ni/NiO arrays prepared by hydrothermal synthesis and electrodeposition methods. • Ni/NiO nanoflake arrays show high capacity for alkaline batteries. • Introducing Ni to the NiO nanoflake is favorable for fast electron transfer. - Abstract: Construction of metal/metal oxide composite arrays is highly important for developing advanced electrochemical energy devices. In this work, we report a facile electrodeposition method to embed Ni network into hydrothermal NiO nanoflake arrays. Ni nanoparticles of 10–25 nm are intimately integrated with NiO nanoflakes of 20–30 nm forming cross-linked Ni/NiO composite arrays. The electrochemical potentials of Ni/NiO composite arrays are explored as cathode of alkaline batteries by means of galvanostatic charge/discharge tests and cyclic voltammograms (CV) in KOH solution. Compared with the unmodified NiO nanoflake arrays, the Ni/NiO composite arrays show much better electrochemical properties with higher capacity (100 mAh g{sup −1} vs. 75 mAh g{sup −1} at 2 A g{sup −1}), enhanced cycling life (capacity retention: 96% vs. 82%) after 3800 cycles and improved high-rate capability. The introduction of Ni nanoparticles not only improves the electrical conductivity, but also acts as anchors to fasten the active nanoflakes to achieve long-term cycles.

36 MATERIALS SCIENCE↗

Deposition of various metal, ceramic, and cermet coatings by an industrial-scale large area filtered arc deposition process

Nearly defect-free nitride, carbide, and oxiceramic coatings have been deposited by a unidirectional dual large area filtered arc deposition (LAFAD) process. One LAFAD dual arc vapor plasma source was used in both gas ionization and coating deposition modes with and without vertical magnetic rastering of the plasma flow. Substrates made of different metal alloys, as well as carbide and ceramics, were installed at different vertical positions on the 0.5 m diameter turntable of the industrial-scale batch coating system which was rotated at 12 rpm to assess deposition rates and coating thickness uniformity. Targets of the same or different compositions were installed on the primary cathodic arc sources of the LAFAD plasma source to deposit a variety of coating compositions by mixing the metal vapor and reactive gaseous components in a magnetically confined, strongly ionized plasma flow with large kinetic energy. The maximum deposition rate typically ranged from 1.5 {mu}m/h for TiCr/TiCrN to 2.5 {mu}m/h for Ti/TiN multilayer and AlN single layer coatings, and up to 6 {mu}m/h for AlCr-based oxiceramic coatings for primary cathode current ranging from 120 to 140 A. When the arc current was increased to 200 A, the deposition rates of TiN-based coatings were as high as 5 {mu}m/h. The vertical coating thickness uniformity was {+-}15% inside of a 150 mm area without vertical rastering. Vertical rastering increased the uniform coating deposition area up to 250 mm. The coating thickness distribution was well correlated with the output ion current distribution as measured by a multisection ion collector probe. Coatings were characterized for thickness, surface profile, adhesion, hardness, and elemental composition. Estimates of electrical resistivity indicated good dielectric properties for most of the TiCrAlY-based oxiceramic, oxinitride, and nitride coatings. The multielement LAFAD plasma flow consisting of fully ionized metal vapor with a reactive gas ionization rate in excess of 50% was found especially suitable for deposition of nanocomposite, nanostructured coatings. Potential industrial applications of this highly productive coating deposition process are discussed.

36 MATERIALS SCIENCE↗

Emission Properties of Metal Porous Cathodes Modified by Nanocarbon

The results of studying the emissive ability, structure, and elemental composition of the surface of an impregnated cathode with a fine-grained tungsten matrix with addition of polyhedral multilayer carbon nanostructures of the fulleroid type (0.2−0.7 wt %), impregnated with barium-calcium aluminate with addition of sulfoadduct of carbon nanoclusters (0.1−0.2 wt %), are presented. The tests in diode prototypes showed that these cathodes provide a current density of 20 A/cm{sup 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Progress in direct recycling of spent lithium nickel manganese cobalt oxide (NMC) cathodes

With the widespread use of lithium-ion batteries (LIBs) in portable electronics and electric vehicles (EVs), the end-of-life (EOL) LIBs are projected to reach 1336 GWh by 2040 under the sustainable development scenario. Proper recycling is urgently needed to minimize the release of hazardous waste and reduce mining activities by reintroducing critical minerals into the supply chain. Lithium nickel manganese cobalt oxide (LiNi x Mn y Co z O 2 , NMCs) cathodes have become dominant in the LIB market, especially with the increasing production of EVs, which are also the most valuable components in EOL LIBs. Unlike pyrometallurgical and/or hydrometallurgical methods, which convert spent NMCs into metals or metal compounds, direct recycling technologies aim to maximize the value of spent cathodes by restoring their degraded structure and composition. Furthermore, this review summarizes direct recycling methods for NMC cathodes published in the last decade and provides insights into the challenges and future development of direct recycling techniques.

Cathode↗

Enhanced Raman Scattering from NCM523 Cathodes Coated with Electrochemically Deposited Gold

Materials with the general composition LiMO2, where M is a mix of nickel, cobalt, and manganese, have been studied extensively as cathodes for lithium-based electrochemical cells. Some compositions, like LiNi0.5Co0.2Mn0.3O2 (NCM523), have already found application in commercial lithium-ion batteries. Pre-test and post-test analyses of these types of cathodes have benefited greatly from the use of Raman spectroscopy. Specifically, Raman spectroscopy can be used to investigate the phonons of the LiMO2 lattice. This is particularly useful for studies of the LiMO2 after it has been formed into the type of polymer-bonded laminate from which typical battery cathodes are cut. One of the problems that occurs in such studies is that the scattering from the LiMO2 phase gets progressively weaker as the nickel content increases. NCM523 poses one example of this behavior owing to the fact that half of the transition metal content is nickel. In this study we show that the intensity of the Raman scattering from the NCM523 phonons can be significantly increased by electroplating clusters of sub-micron gold particles on NCM523-containing laminate structures. The gold appears to plate somewhat selectively on the NCM523 particles in randomly sized clusters. These clusters stimulate the Raman scattering from the NCM523 to varying extents that can reach nearly 100 times the scattering intensity from uncoated pristine laminates.

cathode↗

Integrated rocksalt–polyanion cathodes with excess lithium and stabilized cycling

Co- and Ni-free disordered rocksalt cathodes utilize oxygen redox to increase the energy density of lithium-ion batteries, but it is challenging to achieve good cycle life at high voltages >4.5 V (versus Li/Li + ). Here, in this study, we report a family of Li-excess Mn-rich cathodes that integrates rocksalt- and polyanion-type structures. Following design rules for cation filling and ordering, we demonstrate the bulk incorporation of polyanion groups into the rocksalt lattice. This integration bridges the two primary families of lithium-ion battery cathodes—layered/spinel and phosphate oxides—dramatically enhancing the cycling stability of disordered rocksalt cathodes with 4.8 V upper cut-off voltage. The cathode exhibits high gravimetric energy densities above 1,100 Wh kg -1 and >70% retention over 100 cycles. This study opens up a broad compositional space for developing battery cathodes using earth-abundant elements such as Mn and Fe.

36 MATERIALS SCIENCE↗