Search NASA⌕ Search

SEARCH · Search NASA

Results for “curing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Design guidelines for hybrid microcircuits; organic adhesives for hybrid microcircuits

The properties of organic adhesives were studied to acquire an adequate information base to generate a guideline document for the selection of adhesives for use in high reliability hybrid microcircuits. Specific areas covered include: (1) alternate methods for determining the outgassing of cured adhesives; (2) effects of long term aging at 150C on the electrical properties of conductive adhesives; (3) effects of shelf life age on adhesive characteristics; (4) bond strengths of electrically conductive adhesives on thick film gold metallization, (5) a copper filled adhesive; (6) effects of products outgassed from cured adhesives on device electrical parameters; (7) metal migration from electrically conductive adhesives; and (8) ionic content of electrically insulative adhesives. The tests performed during these investigations are described, and the results obtained are discussed in detail.

Perkins, K. L.↗
NASA NTRS1976

Filament-wound spar shell graphite/epoxy fan blades

The methodology for fabrication of wet filament wound spar shell fan blades is presented. All principal structural elements were filament wound, assembled, formed, bonded and co-cured in a female mold. A pair of blades were fabricated as one integral unit and parted into two after curing.

Yao, S.↗
NASA NTRS1976

Effect of ester impurities in PMR-polyimide resin

Spectral and chomatographic studies were conducted which established the presence of tri- and tetraester impurities in aged monomer solutions employed in fabrication of PMR-polyimide resin composites. The equilibrium constant and apparent rate of the esterification were determined. It was demonstrated, using differential scanning calorimetry, that the ortho-ester moiety of these impurities does not completely react at typical cure conditions. It is concluded that voids formed in composites fabricated with aged monomer solution are due to gaseous decomposition products evolved by ester impurities and/or unreacted amine during elevated temperature post-cure treatment.

Lauver, R. W.↗
NASA NTRS1976

Thermal analysis of PMR-polyimides by dielectrometry

A preliminary study was conducted to determine the dielectric properties of glass fabric reinforced composites as influenced by the reactions occurring during the preparation of crosslinked polyimides by the PMR process. The variables studied included: formulated molecular weight, staging temperature and time; rate of temperature increase to cure temperature; and cure temperature and time. The changes of capacitance and, particularly, of dissipation factor were found to be strongly dependent on each of the variables studied.

Gluyas, R. E.↗
NASA NTRS1976

Prediction of crosslink density of solid propellant binders

A quantitative theory is outlined which allows calculation of crosslink density of solid propellant binders from a small number of predetermined parameters such as the binder composition, the functionality distributions of the ingredients, and the extent of the curing reaction. The parameter which is partly dependent on process conditions is the extent of reaction. The proposed theoretical model is verified by independent measurement of effective chain concentration and sol and gel fractions in simple compositions prepared from model compounds. The model is shown to correlate tensile data with composition in the case of urethane-cured polyether and certain solid propellants. A formula for the branching coefficient is provided according to which if one knows the functionality distributions of the ingredients and the corresponding equivalent weights and can measure or predict the extent of reaction, he can calculate the branching coefficient of such a system for any desired composition.

Marsh, H. E., Jr.↗
NASA NTRS1978

Adhesiveless and grooveless sealing technique

Sealing technique eliminates groove or adhesive bonding and its attendant heating and curing need to finely finish at least one surface to be sealed. Seal could be mounted either inside or outside seal line, and could be installed in final assembly without exposing part to heat and pressure of curing.

Martin, J. W.↗
NASA NTRS1976

Residual stresses in polymer matrix composite laminates

Residual stresses in composites are induced during fabrication and by environmental exposure. The theory formulated can describe the shrinkage commonly observed after a thermal expansion test. Comparison between the analysis and experimental data for laminates of various material systems indicates that the residual stress-free temperature can be lower than the curing temperature, depending on the curing process. Effects of residual stresses on ply failure including the acoustic emission characteristics are discussed.

Hahn, H. T.↗
NASA NTRS1976

Advanced composite rudders for DC-10 aircraft: Design, manufacturing, and ground tests

Design synthesis, tooling and process development, manufacturing, and ground testing of a graphite epoxy rudder for the DC-10 commercial transport are discussed. The composite structure was fabricated using a unique processing method in which the thermal expansion characteristics of rubber tooling mandrels were used to generate curing pressures during an oven cure cycle. The ground test program resulted in certification of the rudder for passenger-carrying flights. Results of the structural and environmental tests are interpreted and detailed development of the rubber tooling and manufacturing process is described. Processing, tooling, and manufacturing problems encountered during fabrication of four development rudders and ten flight-service rudders are discussed and the results of corrective actions are described. Non-recurring and recurring manufacturing labor man-hours are tabulated at the detailed operation level. A weight reduction of 13.58 kg (33 percent) was attained in the composite rudder.

Lehman, G. M.↗
NASA NTRS1975

Investigation of organic adhesives for hybrid microcircuits

The properties of organic adhesives were investigated to acquire information for a guideline document regarding the selection of adhesives for use in high reliability hybrid microcircuits. Specifically, investigations were made of (1) alternate methods for determining the outgassing of cured adhesives, (2) effects of long term aging at 150 C on the electrical properties of conductive adhesives, (3) effects of shelf life age on adhesive characteristics, (4) bond strengths of electrically conductive adhesives on thick film gold metallization, (5) a copper filled adhesive, (6) effects of products outgassed from cured adhesives on device electrical parameters, (7) metal migration from electrically conductive adhesives, and (8) ionic content of electrically insulative adhesives. The tests performed during these investigations are described, and the results obtained are discussed.

Perkins, K. L.↗
NASA NTRS1977

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 2

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacturer of larger helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D, was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR R-49/epoxy skin and graphite/epoxy frames and stringers. The single cure concept is made possible by the utilization of pre-molded foam cores, over which the graphite/epoxy pre-impregnated frame and stringer reinforcements are positioned. Bolted composite channel sections were selected as the optimum joint construction. The applicability of the single cure concept to larger realistic curved airframe sections, and the durability of the composite structure in a realistic spectrum fatigue environment, was described.

Adams, K. M.↗
NASA NTRS1976

Fabrication of PDA/HTS prototype components

A process was developed for autoclave molding structural poly-(Diels-Alder) polyimide (PDA) resin/HTS graphite composites for short-term 600 F service. The autoclave molding process used to fabricate these composites required a maximum cure temperature of 427 K (400 F) and a maximum molding pressure of 0.7 MN/sq m (100 psig). This process then was adapted to the fabrication of co-cured polyimide sandwich panels consisting of PDA/HTS skins, PDA syntactic foam and polyimide/glass honeycomb core. Fabrication ease was demonstrated by manufacturing five three-quarter scale YF-12 wing panels using the PDA resin. It was concluded from successful evaluation of these prototype units that the PDA resin is suitable for fabrication of components using commercial equipment.

Sheppard, C. H.↗
NASA NTRS1977

Thermal expansion of an epoxy-glass microsphere composite

The thermal expansion of a composite of epoxy (diglycidyl ether of bisphenol A) and solid glass microspheres was investigated. The microspheres had surfaces which were either untreated or treated with a silicone release agent, an epoxy coupling agent, or a general purpose silane coupling agent. Both room temperature (about 300 K) and elevated temperature (about 475 K) cures were used for the epoxy. Two microsphere size ranges were used, about 50 microns, which is applicable in filled moldings, and about 125 microns, which is applicable as bond line spacers. The thermal expansion of the composites was measured from 300 to 350 K or from 300 to 500 K, depending on the epoxy cure temperature. Measurements were made on composites containing up to .6 volume fraction microspheres. Two predictive models, which required only the values of thermal expansion of the polymer and glass and their specific gravities, were tested against the experimental data. A finite element analysis was made of the thermal strain of a composite cell containing a single microsphere surrounded by a finite-thickness interface.

Price, H. L.↗
NASA NTRS1979

Low-cost graphite/epoxy structural panels

Manufacturing process precures components of composite panels prior to assembly. Process separately cures the graphite/epoxy skin, stiffener ribs, and stiffener grid. After curing, panels are assembled using special adhesive. With implementation of cost effective manufacturing techniques, uses of graphite-epoxy laminate panels may be found in other areas such as auto industry.

Lager, J. R.↗
NASA NTRS1976

Silver-Teflon coating improvement

Approximately forty adhesives were subjected to laboratory screening. Seven candidate adhesives were selected from the screening tests and evaluated in a thermal vacuum test on radiator panels similar to the anticipated flight hardware configuration. Several classes of adhesives based on epoxide, polyester, silicone, and urethane resin systems were tested. These included contact adhesives, heat cured adhesives, heat and pressure cured adhesives, pressure sensitive adhesives, and two part paint-on or spray-on adhesives. The panels were tested in a space environmental simulation laboratory chamber during the July 9-20, 1973 time span.

Reed, M. W.↗
NASA NTRS1977

Composite lamination method

A process was developed for preparing relatively thick composite laminate structure wherein thin layers of prepreg tapes are assembled, these thin layers are cut into strips that are partially cured, and stacked into the desired thickness with uncured prepreg disposed between each layer of strips. The formed laminate is finally cured and thereafter machined to the desired final dimensions.

Dickerson, G. E.↗
NASA NTRS1978

Solid propellant motor

A case bonded end burning solid propellant rocket motor is described. A propellant with sufficiently low modulus to avoid chamber buckling on cooling from cure and sufficiently high elongation to sustain the stresses induced without cracking is used. The propellant is zone cured within the motor case at high pressures equal to or approaching the pressure at which the motor will operate during combustion. A solid propellant motor with a burning time long enough that its spacecraft would be limited to a maximum acceleration of less than 1 g is provided by one version of the case bonded end burning solid propellant motor of the invention.

Shafer, J. I.↗
NASA NTRS1977

Lamination residual strains and stresses in hybrid laminates

An investigation is conducted of the effects of hybridization on the magnitude of lamination residual stresses. Eight-ply graphite/Kevlar 49/epoxy and graphite/S-glass/epoxy laminates were studied. The same matrix resin was selected for all basic materials to ensure compatibility and uniform curing of the various plies. The specimens, with inserted strain gages and thermocouples, were subjected to curing and postcuring cycles in an autoclave. Subsequently, the specimens were subjected to a thermal cycle from room temperature to 444 K and down to room temperature. It was found that hydridizing reduces apparently residual strains and stresses in the graphite plies. However, these strains were not affected much by the type and degree of hybridization.

Daniel, I. M.↗
NASA NTRS1978

Kalman filter divergence and aircraft motion estimators

Kalman filters designed for many aerospace systems turn out to be unsatisfactory. The estimate errors become large compared to the errors predicted by the theory ('divergence'). One of the principal causes of this failure is that the system model contains states or modes that are undisturbed by the modeled process noise, and are neutrally stable (NS). One cure for such problems is periodic restarting of a time-varying Kalman filter. Other cures include minimum variance observers with eigenvalue constraints, added noise, pole-shifting, and destabilization. Several examples are given, including effective time-invariant estimators for the longitudinal and lateral motions of an airplane where several NS modes are undisturbed by wind gusts. An interpretation of these estimators as a 'strapdown IMU' without accelerometers, gimbaled gyros, or servos is given.

Bryson, A. E., Jr.↗