Search NASA⌕ Search

SEARCH · Search NASA

Results for “difference in differences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

In situ quantification of fracture slip induced by hydraulic injections in a deep borehole: A comparison of two different borehole techniques

In situ measurements of fracture deformation during fluid injection are rare, yet essential for understanding the mechanical response of fractured rock. In this study, we evaluate the reliability of two methods by comparing their slip vector estimates: high-resolution borehole acoustic televiewer images captured before and after injection tests, and displacement data from a three-component borehole deformation probe recorded during the injections. Acoustic televiewer images capture only final in-plane displacement, whereas three-component borehole deformation measurements provide full 3D, transient fracture movement. Four injection tests in a fractured granitic rock mass along an inclined borehole at the Bedretto Underground Laboratory (Switzerland), beneath more than 1100 m of overburden, were analyzed. The two methods yielded consistent kinematics and comparable slip magnitudes, typically in the range of 0.2 – 0.6 mm. Angular differences between estimated slip directions ranged from 0.2° to 28°. For two test intervals with pre-existing fractures optimally oriented for slip, the measured slip vectors agreed with forward-modeled slip vectors based on the regional in situ stress field, supporting the Wallace–Bott hypothesis. Measurable shear displacement was identified in two test intervals containing fractures oriented nearly perpendicular to the least principal stress, including a newly formed hydraulic fracture. This demonstrates that even fractures unfavorably oriented for slip can undergo shear due to local stress perturbations around an inclined borehole.

Acoustic televiewer↗
DOE OSTI2021

Quantification of Intrafraction and Interfraction Tumor Motion Amplitude and Prediction Error for Different Liver Tumor Trajectories in Cyberknife Synchrony Tracking

To research the fiducial-based, real-time tracking intrafraction (during the fraction [intra-]) and interfraction (between fractions [inter-]) tumor respiration amplitude, motion trajectory, and prediction error and quantify their relationships for different types of motion trajectories during Cyberknife-based stereotactic ablation radiotherapy.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2021

Characterization of Dosimetric Differences in Strut-Adjusted Volume Implant Treatment Plans Calculated With TG-43 Formalism and a Model-Based Dose Calculation Algorithm

To comprehensively characterize dosimetric differences between calculations with a commercial model-based dose calculation algorithm (MBDCA) and the TG-43 formalism in application to accelerated partial breast irradiation (APBI) with the strut-adjusted volume implant (SAVI) applicator.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2021

Lung Cancer and Heart Disease Risks Associated With Low-Dose Pulmonary Radiotherapy to COVID-19 Patients With Different Background Risks

The respiratory disease COVID-19 reached global pandemic status in 2020. Excessive inflammation is believed to result in the most severe symptoms and death from this disease. Because treatment options for patients with severe COVID-19 related pulmonary symptoms remain limited, whole-lung low-dose radiation therapy is being evaluated as an anti-inflammatory modality. However, there is concern about the long-term risks associated with low-dose pulmonary irradiation. To help quantify the benefit-risk balance of low-dose radiation therapy for COVID-19, we estimated radiation-induced lifetime risks of both lung cancer and heart disease (major coronary events) for patients of different sexes, treated at ages 50 to 85, with and without other relevant risk factors (cigarette smoking and baseline heart disease risk).

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2020

The physiochemical alteration of flax fibers structuring components after different scouring and bleaching treatments

Scouring and bleaching are essential steps in flax yarn production; however, in many cases, these treatments have relatively low selectivity on non-cellulosic polysaccharides (NCPs) and lignin. Herein, the specific chemical properties of flax fibers through a variety of scouring and/or bleaching procedures are reviewed to understand their correlations with the mechanical and morphological characteristics. The hydrolysis behaviors of hemicellulose and lignin are different from those of cellulose during chlorine-alkali-oxygen (Cl-AO), enzyme-alkali-oxygen (EAO), and alkali-oxygen (AO) treatments, while the structural hemicellulose polysaccharides fractions were not affected by acid pretreatment followed by alkali scouring (AA) treatment. It was found that the unbleached AA treatment improved scouring efficiency to the greatest extent by decreasing 73.3 % of hemicellulose content and 59.8 % of lignin content compared to the untreated flax fibers and obtained the highest tensile strength (6.58 cN/dtex) and elongation (3.73 %). Delignification was more crucial on fiber tenacity and fineness than hemicellulose removal (R 2 = 0.71, 0.79 vs R 2 = 0.46, 0.61). Within the hemicellulose fractions, a corresponding beneficial relationship between the xylan (XYL) composition and flax fiber properties is presented. The correlation of GM and GGM contents in hemicellulose with flax fiber length was significant with R 2 value 0.97 and 0.99, respectively. This work provides insight into the hydrolysis behavior of hemicellulose and a basis for developing scouring and/or bleaching models that can predict fiber properties.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

A high-order finite difference method for moving immersed domain boundaries and material interfaces

Here, we present a high-order sharp treatment of immersed moving domain boundaries and material interfaces, and apply it to the advection-diffusion equation in two and three dimensions. The spatial discretization combines dimension-split finite difference schemes with an immersed boundary treatment based on a weighted least-squares reconstruction of the solution, providing stable discretizations with up to sixth order accuracy for diffusion terms and third order accuracy for advection terms. The temporal discretization relies on a novel strategy for maintaining high-order temporal accuracy in problems with moving boundaries that minimizes implementation complexity and allows arbitrary explicit or diagonally-implicit Runge-Kutta schemes. The approach is broadly compatible with popular PDE-specialized Runge-Kutta time integrators, including low-storage, strong stability preserving, and diagonally implicit schemes. Through numerical experiments we demonstrate that the full discretization maintains high-order spatial and temporal accuracy in the presence of complex 3D geometries and for a range of boundary conditions, including Dirichlet, Neumann, and flux conditions with large jumps in coefficients.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Machine learning models for estimating contamination across different curbside collection strategies

Contaminated recyclables, which are frequently discarded as waste, pose a significant challenge to the implementation of a circular economy. These contaminated recyclables impede the circulation of resources, resulting in higher processing costs at material recovery facilities (MRFs). Over the past few decades, machine learning (ML) models such as linear regression (LR), support vector machine (SVM), and random forest (RF) have evolved to provide new methods for predicting inbound contamination rates in addition to traditional statistical models. In this study, we applied ML models to predict inbound contamination rates using demographic features from 15 counties in the U.S. with different curbside collection strategies. In general, we found that ML models outperformed linear mixed models. Specifically, SVM models had the highest performance (R 2 = 0.75; mean absolute error (MAE) = 0.06), which may be due to their ability to model nonlinear relationships between features and inbound contamination rates. Further, the key predictor was population, with poverty rate being positively correlated and median age negatively correlated with inbound contamination rates. To improve the management of contamination and enhance the implementation of a circular economy, better models are needed to understand and estimate inbound contamination rates as well as identify critical factors in the present and future.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Evaluating three evapotranspiration estimates from model of different complexity over China using the ILAMB benchmarking system

The land surface models range in complexity of terrestrial evapotranspiration, yet it is unknown how model complexity translates to accuracy of modeled evapotranspiration estimates. Here, we use the International Land Model Benchmarking system to assess ET estimates from three models of varying complexity driven by the same forcing datasets: an earth system model, a terrestrial biosphere model, and a stand-alone ET model. The performance assessment includes both temporal and spatial evaluation, and different plant functional types across China. Our results indicate that the most complex model, an earth system model, performed best against the benchmarking datasets and metrics. Terrestrial biosphere model performed best in simulating inter-annual variability of ET, while earth system model performed best in simulating the seasonal cycle. The more complex models (earth system model and terrestrial biosphere model) perform better in forest, shrub and crop ecosystems, while the simpler model (stand-alone ET model) perform better in grass ecosystems. Our study demonstrates the impact of model complexity on ET estimates and highlights directions for future ET model improvements.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Can artificial intelligence and data-driven machine learning models match or even replace process-driven hydrologic models for streamflow simulation?: A case study of four watersheds with different hydro-climatic regions across the CONUS

With recent developments in computational techniques, Data-driven Machine Learning Models (DMLs) have shown great potential in simulating streamflow and capturing the rainfall-runoff relationship in given watersheds, which are traditionally fulfilled by Process-based Hydrologic Models (PHMs). There are debates on whether the DMLs can outperform and possibly replace the classical PHMs for streamflow simulation and river forecasting, but no clear conclusions have been made. This study aims to investigate whether the newer DMLs have any potential in further improving the simulation accuracy of classical PHMs, and vice versa. To do this, we compared a few popular PHMs and DMLs over four watersheds across the Continental US (CONUS) that are associated with different input, climate, and regional conditions. A total of five hydrologic models were chosen, including (1) two classical lumped models, i.e., the Sacramento Soil Moisture Accounting (SAC-SMA) and Xinanjiang (XAJ); (2) one modern distributed model, termed Coupled Routing and Excess Storage (CREST); (3) and two DMLs including an Artificial Neural Networks (ANN) and a deep learning model, termed Long Short Term Memory (LSTM). Our results demonstrated that the DMLs still significantly biased when using the baseline input scenario with the PHMs. However, the DMLs fed with delayed input scenarios had great potential and can reach high simulation accuracy. The DMLs, especially the ANN, outperformed other employed models under the rainfall-runoff relationship in which rainfall dominantly drives. Furthermore, the DMLs also showed better performance in the high-flow regime, while the PHMs had a better performance for the low-flow regime, implying both PHMs and DMLs have their own merits and are worthy of joint development. In general, our study indicated a great potential of using DMLs to simulate streamflow, but further studies are still needed to verify the transferability and scalability of DMLs in large-scale experiments, such as the Distributed Model Intercomparison Projects 1&2 conducted by National Weather Services but to compare modern DMLs and PHMs.

58 GEOSCIENCES↗
DOE OSTI2021

In-situ ion irradiation study of alloy 709 stainless steels with different processing histories

Alloy 709 stainless steel (A709 SS) has gained an increased interest in nuclear applications due to its advanced properties at high temperatures over the widely used Type 316 SS. However, how this alloy behaves under irradiation with concurrent environmental factors, such as mechanical deformation and/or thermal annealing, has not been studied. In this work, we used in-situ ion irradiation inside a transmission electron microscope (TEM) to investigate the effects of irradiation on the microstructures of A709 SS samples with different prior processing histories, including as-received, annealed, and creep-deformed. It was found that, compared to room temperature irradiation, 600 degrees C irradiation led to larger dislocation loop sizes and lower loop densities. Furthermore, with 600 degrees C irradiation, the creep-deformed sample, which had the highest precipitate density and the highest dislocation density, had the smallest loop size and the lowest loop density compared to others. This observation has been rationalized with quantitative evaluation of the sink strength factors in each sample. This study shows that in-service deformation can significantly affect the irradiation performance in structural materials at reactor operating conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding of three different polyvinylpyrrolidone (PVP) based battery binders blends on graphene surfaces from first principles via DFT simulations

Binders play a crucial role in binding electrodes, current collectors, and conductive agents during battery manufacturing. The selection of the binders and their blends considerably affect various properties such as mechanical durability, adhesion performance, ionic/electronic conductivities, and solid electrolyte interface stability for lithium-ion batteries. In this work, polyvinylidene di-fluoride (PVDF), polyacrylic acid (PAA), polyvinylpyrrolidone (PVP), and lithiated polyacrylic acid (Li-PAA) were selected as the model binders, and their blends were studied on graphene surfaces. Further, among them, PVDF is hardly soluble in water unlike the other binders, so in practice, the blend of PVP:PVDF is not thought to be a proper combination. However, the PVP:PVDF binder has also been included because the purpose of this work is to calculate several electronic properties such as binding energies, intermolecular interaction energies, bond critical points, electron density, and the Laplacian of electron density at critical bonding regions of all these blends at the molecular level via density functional theory (DFT) simulations in order to evaluate and compare how is the interaction strength and bonding type of three different lithium-ion batteries (LIBs) binder blends on graphene surfaces. Most stable binder pairs and their binding mechanisms on graphene surfaces were studied. The delocalization of lithium in Li-PAA was studied with the presence of water.

25 ENERGY STORAGE↗
DOE OSTI2021

Strain rate effects on the mechanical behavior of porous titanium with different pore sizes

High strain-rate (up to 6600 s –1 ) and quasi-static compression tests are conducted on a powder-sintered porous titanium with different pore sizes (mean: 30 μm and 120 μm). In situ X-ray imaging is implemented to characterize the pores-scale deformation dynamics. The yield strength as a function of strain rate exhibits two stages of rate sensitivity, and the transition occurs at 1600 s –1 . X-ray images show that pore compaction and strain localizations occur preferentially at pores oriented perpendicular to the loading direction under quasi-static loading, but become more random under high strain-rate loading as a result of higher driving force and plastic deformation nucleation rate. Here, the more homogeneous nucleation of plastic deformation contributes to the increased rate sensitivity beyond 1600 s –1 . At the same strain rate, the yield strength of porous Ti as well as strain field homogeneity decreases significantly with increasing pore size. The small pore spacing in fine-pored Ti reduces the degree of stress concentrations around pores. Therefore, the higher stress concentrations in coarse-pored Ti lead to an earlier yield of matrix around pores and thus a lower bulk yield strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synthesis and Characterization of Lignin-grafted-poly(ε-caprolactone) from Different Biomass Sources

Modification of lignin with poly(ε-caprolactone) is a promising approach to valorize industrial low-value lignins and to advance the bioeconomy. We have synthesized lignin grafted poly(ε-caprolactone) (lignin-g-PCL) copolymers via ring-opening polymerization of ε-caprolactone with different types of lignins of varying botanical sources (G-type pine lignin, S/G-type poplar lignin, and C-type Vanilla seeds lignin) and lignin extraction methods (Kraft and ethanol organosolv pulping). The lignin-g-PCL copolymer showed remarkably improved compatibility and dispersion in acetone, chloroform, and toluene in comparison to non-modified lignins. The structure and thermal properties of the lignin-g-PCL were investigated using Fourier-transform infrared spectroscopy (FTIR), 31 P nuclear magnetic resonance (NMR), 2D heteronuclear single quantum correlation (HSQC) NMR, gel permeation chromatography (GPC), and differential scanning calorimetry (DSC). Furthermore, we have found that all the technical lignins were reactive to the copolymerization reaction regardless of their plant source and isolation methods. The molecular weights of the synthesized lignin-g-PCL copolymers were positively correlated with the content of aliphatic lignin hydroxyls, suggesting that the copolymerization reaction tends to occur preferentially at the aliphatic hydroxyls rather than the phenolic hydroxyls of lignin. Thermal analyses of the lignin-g-PCL copolymers were studied, and in general, a reduction of melting temperature and crystallinity percentage in comparison to the neat PCL was observed. However, the thermal behavior of lignin-g-PCL copolymers varied depending on the lignin feedstocks employed in the copolymerization reaction.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Differences in the response of two light guide technologies and two readout technologies after an exchange of liquid argon in the dewar

In this investigation the response to the scintillation light generated by through-going cosmic muons in liquid argon (LAr) was measured by two light guide technologies and two readout technologies after five weeks of running in the TallBo dewar at Fermilab. The response was remeasured after the dewar was drained of LAr, refilled, and then run again for an additional four weeks. After the dewar was refilled, there was clear evidence that the scintillation signal had dropped significantly. The two light guide technologies were developed at Indiana University and MIT/Fermilab. The two readout technologies were boards that passively or actively ganged 12 Hamamatsu MPPCs. Two possible explanations were identified for the degraded signal: the response of the two light guide technologies degraded due to damage caused by thermal cycling, and/or unknown differences in the trace residual Xe contamination in the fills of LAr led to the observed drop in scintillation light. Neither absorption nor quenching by N 2 , O 2 , and H 2 O contamination can account for the degradation. Neither the individual Hamamatsu MPPCs nor the passive/active ganging boards appear to have been affected by the thermal cycling. The path length distributions of the cosmics traversing the dewar appear quite similar in both event samples.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Comparative assessment of different aluminum alloys for neutron beam window applications

The choice of an aluminum alloy window along a neutron beam requires careful consideration depending on the requirements of the instrument end station. The windows should generally be thin to minimize loss of neutrons from the beam due to scattering and absorption but still thick enough to be structurally sound for safety requirements. Further, the microstructure of the material is dependent on the alloy and the preparation method and may introduce scattering artifacts or smearing of the instrument resolution that are not desirable. In this manuscript, SANS and total cross section measurements of several different aluminum alloys will be presented and compared in order to provide some useful insight to engineers working on future neutron instrument design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Grain subdivision and structural modifications by high-energy heavy ions in UO 2 with different initial grain size

Irradiation with 84 MeV Xe ions at peak fluence above 7 × 10 17 ions/cm 2 has been carried out on two UO 2 samples with different initial grain sizes at 300 °C and 500 °C. Characterization of both grain structure and bubble morphology has been performed using transmission electron microscopy, image analysis and precession electron diffraction. The bubble size in the large-grained sample was smaller than that in the standard-grain sample, confirming fission gas precipitation resistance in the former. The ion irradiation in the high electronic energy deposition range has caused formation of a large density of dislocations which resulted in grain polygonization for the sample with standard grain size, which was observed in multiple lamellas extracted next to each other at peak dose. The sample with large grains showed inconsistent behavior. In one case, dislocation pile-up occurred, but no sub-grain formation was observed. An adjacent location showed sub-grain formation, even if to less extent compared to the standard grain-size sample. Furthermore, these findings suggest a limited polygonization resistance in large-grained UO 2 compared to standard-grain UO 2 . Recrystallization of both sample surfaces was present, leaving unclear if this is a surface effect or a consequence of the highest energy deposition rate in this area.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Optical properties of differing nanolayered structures of divalent europium doped barium fluoride thin films synthesized by pulsed laser deposition

Optically-active thin films are employed in a variety of applications, such as LEDs and photovoltaics, due to their ability to act as up- or down-photon energy converters. Their performance depends critically on their composition and structure; thus, the use of novel synthesis techniques that allow for their control at the nanoscale level can result in improved efficiency and practicality. Here, layered thin films consisting of Eu 2+ - doped BaF 2 nanocrystalline layers separated by amorphous Al 2 O 3 were synthesized via sequential pulsed laser deposition using three separate targets for the different components; this synthesis technique provides precise control of layer thickness at the nanoscale along with dopant distribution within the film. Cross-sectional transmission electron microscopy analysis verified the desired nano-layering. Post-deposition heat treatments in a nitrogen atmosphere resulted in samples exhibiting steady emission with a broad peak ranging from 400 to 600 nm and a shoulder at 410 nm. The CIE 1931 chromaticity coordinates are x = 0.26-0.29 and y = 0.32-0.35 and vary as a function of the sample configuration. Because the chromaticity coordinates are close to those of a pure white light (x = 0.33, y = 0.33), these films demonstrate advantageous properties for applications with UV-pumped white light LEDs.

36 MATERIALS SCIENCE↗