Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Comparison of dislocation characterization by electron channeling contrast imaging and cross-correlation electron backscattered diffraction

In this paper, the relative capabilities and limitations of electron channeling contrast imaging (ECCI) and cross-correlation electron backscattered diffraction (CC-EBSD) have been assessed by studying the dislocation distributions resulting from nanoindentation in body centered cubic Ta. Qualitative comparison reveals very similar dislocation distributions between the CC-EBSD mapped GNDs and the ECC imaged dislocations. Approximate dislocation densities determined from ECC images compare well to those determined by CC-EBSD. Nevertheless, close examination reveals subtle differences in the details of the distributions mapped by these two approaches. Finally, the details of the dislocation Burgers vectors and line directions determined by ECCI have been compared to those determined using CC-EBSD and reveal good agreement.

36 MATERIALS SCIENCE↗

Rafting-Enabled Recovery Avoids Recrystallization in 3D-Printing-Repaired Single-Crystal Superalloys

The repair of damaged Ni-based superalloy single-crystal turbine blades has been a long-standing challenge. Additive manufacturing by an electron beam is promising to this end, but there is a formidable obstacle: either the residual stress and γ/γ' microstructure in the single-crystalline fusion zone after e-beam melting are unacceptable (e.g., prone to cracking), or, after solutionizing heat treatment, recrystallization occurs, bringing forth new grains that degrade the high-temperature creep properties. Here, a post-3D printing recovery protocol is designed that eliminates the driving force for recrystallization, namely, the stored energy associated with the high retained dislocation density, prior to standard solution treatment and aging. The post-electron-beam-melting, pre-solutionizing recovery via sub-solvus annealing is rendered possible by the rafting (i.e., directional coarsening) of γ' particles that facilitates dislocation rearrangement and annihilation. The rafted microstructure is removed in subsequent solution treatment, leaving behind a damage-free and residual-stress-free single crystal with uniform γ' precipitates indistinguishable from the rest of the turbine blade. Finally, this discovery offers a practical means to keep 3D-printed single crystals from cracking due to unrelieved residual stress, or stress-relieved but recrystallizing into a polycrystalline microstructure, paving the way for additive manufacturing to repair, restore, and reshape any superalloy single-crystal product.

36 MATERIALS SCIENCE↗

Influence of High Pulsed Magnetic Field on the Dislocations and Mechanical Properties of Al{sub 2}O{sub 3}/Al Composites

At T6 state, Al–Zn–Mg–Cu aluminum matrix composites reinforced with Al{sub 2}O{sub 3} particles generated in situ were subjected to high pulsed magnetic fields at different magnetic induction intensities (B = 2, 3 and 4 T). The results show that the dislocation densities in the treated samples increased with increasing B, and the magnetoplastic effect was determined to be the primary cause. The effect of the magnetic field is believed to alter the spin state of free electrons between dislocations and obstacles from the singlet state (associated with high bonding energy) to the triplet state (low bonding energy). The maximum ultimate tensile strength of 532 MPa was obtained at B = 4 T with 30 pulses, which was 20.7% higher than that of the initial sample, primarily because of dislocation strengthening. At B = 2 T, the elongation was at its maximum of 9.3%, representing an increase of 12% compared with the initial sample, while the associated ultimate tensile strength (447 MPa) was still higher than that of the untreated sample (440 MPa). The relationship between mechanical properties and microstructure was analyzed, and the improved properties observed in this work are explained by the transition of the electron spin state and the piling up of dislocations.

36 MATERIALS SCIENCE↗

Transition of dislocation glide to shear transformation in shocked tantalum

A TEM study of pure tantalum and tantalum-tungsten alloys explosively shocked at a peak pressure of 30 GPa (strain rate: ~1 x 10 4 sec -1 ) is presented. While no ω (hexagonal) phase was found in shock-recovered pure Ta and Ta-5W that contain mainly a low-energy cellular dislocation structure, shock-induced ω phase was found to form in Ta-10W that contains evenly distributed dislocations with a stored dislocation density higher than 1 x 10 12 cm -2 . The TEM results clearly reveal that shock-induced α (bcc) → ω (hexagonal) shear transformation occurs when dynamic recovery reactions which lead the formation low-energy cellular dislocation structure become largely suppressed in Ta-10W shocked under dynamic (i.e., high strain-rate and high-pressure) conditions. A novel dislocation-based mechanism is proposed to rationalize the transition of dislocation glide to twinning and/or shear transformation in shock-deformed tantalum. Lastly, twinning and/or shear transformation take place as an alternative deformation mechanism to accommodate high-strain-rate straining when the shear stress required for dislocation multiplication exceeds the threshold shear stresses for twinning and/or shear transformation.

36 MATERIALS SCIENCE↗

Formation of periodic interfacial misfit dislocation array at the InSb/GaAs interface via surface anion exchange

The relationship between growth temperature and the formation of periodic interfacial misfit (IMF) dislocations via the anion exchange process in InSb/GaAs heteroepitaxy was systematically investigated. The microstructural and electrical properties of the epitaxial layer were characterized using atomic force microscope, high-resolution x-ray diffraction, transmission electron microscopy, and Hall resistance measurement. The formation of interfacial misfit (IMF) dislocation arrays depended on growth temperature. A uniformly distributed IMF array was found in a sample grown at 310 °C, which also exhibited the lowest threading dislocation density. The analysis suggested that an incomplete As-for-Sb anion exchange process impeded the formation of IMF on sample grown above 310 °C. At growth temperature below 310 °C, island coalescence led to the formation of 60° dislocations and the disruption of periodic IMF array. All samples showed higher electron mobility at 300 K than at 77 K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Mechanical and Corrosion Properties of Additively Manufactured CoCrFeMnNi High Entropy Alloy

Here, this study investigates the mechanical and corrosion properties of as-built and annealed equiatomic CoCrFeMnNi alloy produced by laser-based directed energy deposition (DED) Additive Manufacturing (AM). The high cooling rates of DED produced a single-phase, cellular microstructure with cells on the order of 4 μm in diameter and inter-cellular regions that were enriched in Mn and Ni. Annealing created a chemically homogeneous recrystallized microstructure with a high density of annealing twins. The average yield strength of the as-built condition was 424 MPa and exceeded the annealed condition (232 MPa), however; the strain hardening rate was lower for the as-built material stemming from higher dislocation density associated with DED parts and the fine cell size. In general, the yield strength, ultimate tensile strength, and elongation-to-failure for the as-built material exceeded values from previous studies that explored other AM techniques to produce the CoCrFeMnNi alloy. Ductile fracture occurred for all specimens with dimple initiation associated with nanoscale oxide inclusions. The breakdown potential (onset of pitting corrosion) was similar for the as-built and annealed conditions at 0.40 V Ag/AgCl when immersed in 0.6 M NaCl. Pit morphology/propagation for the as-built condition exhibited preferential corrosion of inter-cellular Ni/Mn regions leading to a tortuous pit bottom and cover, while the annealed conditions pits resembled lacy pits similar to 304 L steel. Lastly, a passive oxide film depleted in Cr cations with substantial incorporation of Mn cations is proposed as the primary mechanism for local corrosion susceptibility of the CoCrFeMnNi alloy.

36 MATERIALS SCIENCE↗

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗

Multijunction Solar Cells With Graded Buffer Bragg Reflectors

Metamorphic solar cells can have optimal bandgap combinations through the use of compositionally graded buffers, where the lattice constant is slowly varied over several microns of growth. Bragg reflectors consist of several microns of alternating layers with refractive index contrast and provide a useful internal reflection to multijunction solar cells with optically thin subcells. In this work, we implement distributed Bragg reflectors within the compositionally graded buffers of inverted metamorphic solar cells to add functionality to the buffer. The reflectance of this AlGaInAs 'graded buffer Bragg reflector' is very similar to the reflectance of a similar AlGaAs Bragg reflector external to a buffer as well as the reflectance predicted by the transfer matrix model, indicating that the roughness of the buffer does not drastically reduce the reflection. Reflectance of 72%, 91%, and 98% is achieved in 2, 4, and 8 um buffers using AlGaInAs layers that alternate between 30% and 70% aluminum content. Using a 2 um graded buffer Bragg reflector, the 1.0-eV mismatched subcell of a GaAs/GaInAs tandem has a minor increase in threading dislocation density compared to a standard graded buffer and a small, 20 mV, loss in voltage. As the buffer is thickened, the voltage loss is recuperated and excellent subcell voltages are achieved, indicating that the Bragg reflector is not severely hindering dislocation glide. We demonstrate that the benefits of the graded buffer Bragg reflector for optically thin subcells and subcells containing quantum wells, and conclude that Bragg reflectors can effectively be implemented within graded buffers, adding functionality without adding cost.

14 SOLAR ENERGY↗

Characterization of high-temperature mechanical properties of plasma-cladded coatings with thermo-mechanical coupling

High temperature mechanical properties was detected here to study the failure and strengthening mechanism of the coating-substrate (cobalt-based coatings were fabricated on FV520B substrate) integral structure with thermo-mechanical coupling effects. Microstructure, phase composition, element distribution of the coatings was characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscope (TEM), electron back scattering diffraction (EBSD), X-ray diffraction (XRD), electron probe microanalysis (EPMA) and energy dispersive X-ray analysis (EDS). Results elucidate that fracture occurs in the coating for Co50 coating-substrate structure from 300 °C to 700 °C, but failure position transfer to substrate from coating at elevated temperatures with the addition of niobium and cerium oxide. Throughout, there is no crack originated from the interface. Fracture mechanism: the dislocation pile-up causes great stress concentration in the grain boundary, which results in the nucleation of the crack, and then the crack extends along the hard brittle Fe-Cr phase until the material fails. HRTEM shows the high density dislocation and the severe lattice distortion was formed during tensile deformation. On the macro level, the fracture tends to occur in the coarse dendrites region.

36 MATERIALS SCIENCE↗

Modeling of grain size strengthening in tantalum at high pressures and strain rates

Laser-driven ramp wave compression experiments have been used to investigate the strength (flow stress) of tantalum and other metals at high pressures and high strain rates. Recently this kind of experiment has been used to assess the dependence of the strength on the average grain size of the material, finding no detectable variation with grain size. The insensitivity to grain size has been understood theoretically to result from the dominant effect of the high dislocation density generated at the extremely high strain rates of the experiment. Here we review the experiments and describe in detail the multiscale strength model used to simulate them. The multiscale strength model has been extended to include the effect of geometrically necessary dislocations generated at the grain boundaries during compatible plastic flow in the polycrystalline metal. Lastly, we use the extended model to make predictions of the threshold strain rates and grain sizes below which grain size strengthening would be observed in the laser-driven Rayleigh-Taylor experiments.

36 MATERIALS SCIENCE↗

Slip-free multiplication and complexity of dislocation networks in FCC metals

Abstract During plastic deformation of crystalline solids, intricate networks of dislocation lines form and evolve. To capture dislocation density evolution, prominent theories of crystal plasticity assume that 1) multiplication is driven by slip in active slip systems and 2) pair-wise slip system interactions dominate network evolution. In this work, we analyze a massive database of over 100 discrete dislocation dynamics simulations (with cross-slip suppressed), and our findings bring both of these assumptions into question. We demonstrate that dislocation multiplication is commonly observed on slip systems with no applied stress and no plastic strain rate, a phenomenon we refer to as slip-free multiplication. We show that while the formation of glissile junctions provides one mechanism for slip-free multiplication, additional mechanisms which account for the influence of coplanar interactions are needed to fully explain the observations. Unlike glissile junction formation which results from a binary reaction between a pair of slip systems, these new multiplication mechanisms require higher order reactions that lead to complex network configurations. While these complex configurations have not been given much attention previously, they account for about 50% of the line intersections in our database.

36 MATERIALS SCIENCE↗

Microstructure and high temperature properties of tungsten processed via electron beam melting additive manufacturing

There is considerable interest in the adoption of additive manufacturing for processing refractory metals. The layer-wise fabrication approach enables opportunities for producing complex geometries which cannot be otherwise be achieved via powder metallurgy. However, the processing science is still in its nascent stages and structure–property relations are relatively unexplored. Fundamental research is needed to further develop the technology and enable the fabrication of refractory metals for high temperature applications. Here we focus on the processing of pure tungsten using electron beam melting additive manufacturing. Experimentally we develop a suitable processing window for achieving high density crack free material. Microstructural analysis reveals that the microstructure generally consists of a columnar structure with a (111) build direction fiber preference, although, fiber switching was observed. Process induced deformation is believed to drive the formation of subgrains whose boundaries exhibit a high dislocation density. Additionally, high temperature tensile testing reveals that the material exhibits excellent properties closer to that of annealed tungsten. Significant mechanical anisotropy was observed to be present which is likely driven by strong crystallographic texture.

36 MATERIALS SCIENCE↗

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). Creep specimens were fabricated from rods printed by a laser powder bed fusion process. Six different heat treatments, namely 650 °C/1 h, 700 °C/1 h, 750 °C/1 h, 800 °C/1 h, 900 °C/1 h and 1050 °C/1 h were applied to the creep specimens. The heat-treated specimens were creep-tested under the same condition, 550 °C/275 MPa to evaluate the effect of post-build heat treatment on the creep behavior of AM 316L SS. In the temperature range of 650-750 °C, dislocation density within cells, and cell size and wall thickness were affected by the heat treatment, while elemental segregation at boundaries remained unchanged and Mn-enriched Si oxide particles remained stable. In the temperature range of 750-900 °C, concurrent changes were observed in dislocation cell structures, elemental segregation and oxide particles. The 1050 °C-heat treatment removed cell structures and boundary solute segregations, leading to formation of equiaxed grains; Mn-enriched Si oxide particles in the as-built specimen were replaced by more stable Mn-enriched Cr oxides. The creep life of AM 316L SS increased after the heat treatment at 650 °C and then decreased with increasing temperature up to 900 °C where cell/subgrain structures still existed. The creep rate and creep elongation followed an opposite trend. The creep rate can be correlated with the structural parameters of cell/subgrain size and cell wall/boundary thickness and can be rationalized by different strengthening mechanisms of dislocation cells and subgrains. The heat treatment affected strongly the primary and secondary creep but had a minimal effect on the tertiary creep of AM 316L SS.

316L stainless steel↗

Formation of dislocations via misfit strain across interfaces in epitaxial BaTiO 3 and SrIrO 3 heterostructures

Abstract Dislocations often occur in thin films with large misfit strain as a result of strain energy accumulation and can drastically change the film properties. Here the structure and dislocations in oxide heterostructures with large misfit strain are investigated on atomic scale. When grown on SrTiO 3 (001), the dislocations in both the monolithic BaTiO 3 thin film and its superlattices with SrIrO 3 appear above a critical thickness around 6 nm. The edge component of the dislocations is seen in both cases with the Burgers vector of a ⟨100⟩. However, compared to monolithic BaTiO 3 , the dislocation density is slightly lower in BaTiO 3 /SrIrO 3 superlattices. In the superlattice, when considering the SrTiO 3 lattice constant as the reference, BaTiO 3 has a larger misfit strain comparing with SrIrO 3 . It is found that in both cases, the formation of dislocation is only affected by the critical thickness of the film with larger lattice misfit (BaTiO 3 ), regardless of the existence of a strong octahedral tilt/rotation mismatch at BaTiO 3 /SrIrO 3 interface. Our findings suggest that it is possible to control the position of dislocations, an important step toward defect engineering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High Strength, Utilizable Ductility and Electrical Conductivity in Cold Rolled Sheets of Cu-Cr-Zr-Ti Alloy

The microstructure and properties of Cu-0.5Cr-0.03Zr-0.04Ti (wt.%) alloy subjected to cold rolling and aging were investigated using hardness and electrical conductivity measurement, tensile testing, and transmission electron microscopy. Plates subjected to 85% reduction in thickness showed significant improvement in the strength compared to solution treated and aged condition. By proper selection of aging temperature, ductility could be significantly improved without reduction in the strength. Aging of the cold rolled sheet at 420 °C for 1 h yielded an ultimate tensile strength and yield strength of 540 and 460 MPa, respectively. On the other hand, total and uniform elongation was 16 and 12%, respectively, with an electrical conductivity of 65 %IACS. The combination of properties achieved after cold rolling and aging is attributed to the higher dislocation density, ultrafine grains and nano-sized chromium precipitates.

36 MATERIALS SCIENCE↗

Transient solute drag and strain aging of dislocations

The transient drag force exerted by mobile solutes on a moving dislocation is computed using continuum theory. These mobile solutes form so-called Cottrell atmospheres around dislocations during static and dynamic strain aging. We evaluate the evolution of the drag force exerted by the atmosphere under two velocity time-histories: impulsive acceleration to a chosen velocity and a constant acceleration rate. A particular focus is on the conditions under which the stationary limit assumed by theories of dynamic strain aging is obeyed. According to our results, two conditions—one on the dislocation velocity and one on the acceleration rate—must be satisfied for the stationary limit to hold. Using the Orowan relation and a line tension model, we obtain estimates for the temperature, stress, strain rate, and dislocation density regimes where the stationary limit is valid, and compare these results with experiments for a few material systems.

36 MATERIALS SCIENCE↗

Atomic-scale studies on the effect of boundary coherency on stability in twinned Cu

The stored energy and hardness of nanotwinned (NT) Cu are related to interaction between dislocations and (111)-twin boundaries (TBs) studied at atomic scales by high-angle annular dark-field scanning transmission electron microscope. Lack of mobile dislocations at coherent TBs (CTBs) provides as-deposited NT Cu a rare combination of stability and hardness. The introduction of numerous incoherent TBs (ITBs) reduces both the stability and hardness. While storing more energy in their ITBs than in the CTBs, deformed NT Cu also exhibits high dislocation density and TB mobility and therefore has increased the driving force for recovery, coarsening, and recrystallization.

36 MATERIALS SCIENCE↗

Nugget Structure Evolution with Rotation Speed for High-Rotation-Speed Friction-Stir-Welded 6061 Aluminum Alloy

High-rotation-speed friction stir welding (HRS-FSW) is a promising technique to reduce the welding loads during FSW and thus facilitates the application of FSW for in situ fabrication and repair. In this study, 6061 aluminum alloy was friction stir welded at high-rotation speeds ranging from 3000 to 7000 rpm at a fixed welding speed of 50 mm/min, and the effects of rotation speed on the nugget zone macro- and microstructures were investigated in detail in order to illuminate the process features. Temperature measurements during HRS-FSW indicated that the peak temperature did not increase consistently with rotation speed; instead, it dropped remarkably at 5000 rpm because of the lowering of material shear stress. The nugget size first increased with rotation speed until 5000 rpm and then decreased due to the change of the dominant tool/workpiece contact condition from sticking to sliding. At the rotation speed of 5000 rpm, where the weld material experienced weaker thermal effect and higher-strain-rate plastic deformation, the nugget exhibited relatively small grain size, large textural intensity, and high dislocation density. Consequently, the joint showed superior nugget hardness and simultaneously a slightly low tensile ductility.

36 MATERIALS SCIENCE↗