Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation loops”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Decay of skeins of dislocations in cholesterics: rewiring Conway's tangles into necklaces of bangles

Knotted and linked skeins of vortices and disclinations generated, respectively, by symmetry-breaking normal → superfluid and isotropic → nematic phase transitions are known to untie, by rewiring of their crossings, into independent unknots that finally shrink and collapse until the defect-free ground state is reached. We demonstrate that the decay of skeins of dislocations, generated by the isotropic → cholesteric phase transition within a cylinder/cylinder gap, leads to stable necklace-like states made of numerous minimal loops, called bangles, tethered to kinks of much larger loops called cargo. We analyze the topological decay of skeins of dislocations in terms of the Conway–Kauffman theory of knots, showing that the necklace state results from rewiring of crossings triggered by collisions of tangles with their numerator closure. We point out that, in general, for symmetry reasons, kinks on edge dislocations are chiral. Their handedness, right or left, directly depends on the sign of kinks on which they are localized. In cholesterics with intrinsic chirality, the energy of kinks bearing bangles depends on their handedness. For this reason, within necklaces, all bangles are tethered to kinks of the same sign.

Lee, Jun-Yong [International Institute for Sustain↗

Temperature dependence of deformation mechanisms and tensile strength of a new Ni-Fe-base superalloy

Highlights: • A new Ni-Fe-base superalloy with low cost has been developed. • The new alloy has excellent creep-rupture and tensile properties. • Its yield strength is insensitive to temperature below 700 °C. • The main tensile deformation mechanism of the alloy is APB shearing below 700 °C. - Abstract: After a standard heat treatment, the influence of temperature on the tensile strength and corresponding deformation mechanisms of a new Ni-Fe-base superalloy with a low γ' volume fraction are investigated in the temperature region between room temperature and 800 °C. Experimental results show that the yield strength of the experimental alloy is temperature independent below 700 °C, whereas, above the temperature, its yield strength decreases dramatically with temperature. Analyses of micromechanisms controlling the deformation behavior reveal that plastic deformation is accomplished mainly by anti-phase boundary (APB)-coupled dislocations shearing through γ' precipitates below 700 °C, while, above the temperature, the primary deformation mechanism changes from APB shearing to stacking fault shearing and then to precipitate bypassing via Orowan looping together with cross-slip and local climb of dislocations. Based on the experimental results, it is deemed that the transition in the operative strengthening mechanism with temperature accounts for the variation of the yield strength of the experimental alloy with temperature.

36 MATERIALS SCIENCE↗

A parallel discrete dislocation dynamics/kinetic Monte Carlo method to study non-conservative plastic processes

Non-conservative processes play a fundamental role in plasticity and are behind important macroscopic phenomena such as creep, dynamic strain aging, loop raft formation, etc. In the most general case, vacancy-induced dislocation climb is the operating unit mechanism. While dislocation/vacancy interactions have been modeled in the literature using a variety of methods, the approaches developed rely on continuum descriptions of both the vacancy population and its fluxes. However, there are numerous situations in physics where point defect populations display heterogeneous concentrations and/or non-smooth kinetics. Here, a kinetic Monte Carlo (kMC) approach for modeling vacancy transport in response to arbitrary stress fields is used. Vacancies are treated as point particles and are coupled to the dislocation substructure representing a deformed material via an advection term defined by the local stress gradients. The stress fields and the dislocation substructure are evolved using a discrete dislocation dynamics (DDD) module. To extend the coupled model to the treatment of large systems, we have implemented it in the massively-parallel DDD code ParaDiS. To avoid numerical incompatibilities associated with merging deterministic (DDD) and stochastic (kMC) integration algorithms, we cast the entire elasto-plastic-diffusive problem within a single stochastic framework, taking advantage of a parallel kMC algorithm to evolve the system as a single event-driven process. The large-scale implementation enables the study of the evolution of a variety of dislocation-defect scenarios governed by non-conservative transport kinetics. After carrying out an exhaustive numerical and computational analysis of our parallel algorithm, we show results that emphasize situations where inhomogeneous vacancy dynamics are of relevance, and compare discrete kinetics to continuum solutions for several cases.

36 MATERIALS SCIENCE↗

Scale transition using dislocation dynamics and the nudged elastic band method

Microstructural features such as precipitates or irradiation-induced defects impede dislocation motion and directly influence macroscopic mechanical properties such as yield point and ductility. In dislocation-defect interactions both atomic scale and long range elastic interactions are involved. Thermally assisted dislocation bypass of obstacles occurs when thermal fluctuations and driving stresses contribute sufficient energy to overcome the energy barrier. The Nudged Elastic Band (NEB) method is typically used in the context of atomistic simulations to quantify the activation barriers for a given reaction. In this work, the NEB method is generalized to coarse-grain continuum representations of evolving microstructure states beyond the discrete particle descriptions of first principles and atomistics. The method we employed enables the calculation of activation energies for a View the MathML source glide dislocation bypassing a [001] self-interstitial atom loop of size in the range of 4-10 nm with a spacing larger than 150nm in α-iron for a range of applied stresses and interaction geometries. This study is complemented by a comparison between atomistic and continuum based prediction of barriers.

36 MATERIALS SCIENCE↗

From anti-Arrhenius to Arrhenius behavior in a dislocation-obstacle bypass: Atomistic simulations and theoretical investigation

Dislocations are the primary carriers of plasticity in metallic materials. Understanding the basic mechanisms for dislocation movement is paramount to predicting the material mechanical response. Relying on atomistic simulations, we observe a transition from non-Arrhenius to Arrhenius behavior in the rate of an edge dislocation overcoming the long-range elastic interaction with a prismatic loop in tungsten. Close to the critical resolved shear stress, the process shows a non-Arrhenius behavior at low temperatures. However, as the temperature increases, the activation entropy starts to dominate, leading to a traditional Arrhenius-like behavior. Here, we have computed the activation entropy analytically along the minimum energy path following Schoeck’s method, which captures the cross-over between anti-Arrhenius and Arrhenius domains. Also, the Projected Average Force Integrator (PAFI), another simulation method to compute free energies along an initial transition path, exhibits considerable concurrence with Schoeck’s formalism. We conclude that entropic effects need to be considered to understand processes involving dislocations bypassing elastic barriers close to the critical resolved shear stress. More work needs to be performed to fully understand the discrepancies between Schoeck’s and PAFI compared to molecular dynamics.

36 MATERIALS SCIENCE↗

Fractional Quantum Hall Effect in Weyl Semimetals

Weyl semimetal may be thought of as a gapless topological phase protected by the chiral anomaly, where the symmetries involved in the anomaly are the U(1) charge conservation and the crystal translational symmetry. The absence of a band gap in a weakly interacting Weyl semimetal is mandated by the electronic structure topology and is guaranteed as long as the symmetries and the anomaly are intact. The nontrivial topology also manifests in the Fermi arc surface states and topological response, in particular taking the form of an anomalous Hall effect in magnetic Weyl semimetals, whose magnitude is only determined by the location of the Weyl nodes in the Brillouin zone. In this work, we consider the situation when the interactions are not weak and ask whether it is possible to open a gap in a magnetic Weyl semimetal while preserving its nontrivial electronic structure topology along with the translational and the charge conservation symmetries. Surprisingly, the answer turns out to be yes. The resulting topologically ordered state provides a nontrivial realization of the fractional quantum Hall effect in three spatial dimensions in the absence of an external magnetic field, which cannot be viewed as a stack of two dimensional states. Our state contains loop excitations with nontrivial braiding statistics when linked with lattice dislocations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pre- and post-annealing of mechanical damage in silicon wafers

Basic properties of mechanical damage in silicon consisting of cracks and abrasion were studied using transmission electron microscopy. The crystallographic structure of mechanical damage was determined before and after high temperature annealing. The main findings include that stresses in silicon around crack tips are not plastically relieved at room temperature and that abrasion at room temperature introduces shear loops into the silicon. It was also found that cracks of micron size can be annealed out, specifically, if cleavage occurs on 111 planes. The healing products of such cracks are 60 deg and 90 deg dislocations. Submicron cracks transform into stacking faults during annealing. Likewise high concentrations of shear loops due abrasion were found to anneal into stacking faults. A one to one correlation between surface areas containing small cracks and stacking faults was made. Measurements of damage removal on silicon surfaces through chemical-mechanical etching techniques are presented. It is shown that silicon dioxide repolishes damaged silicon surfaces most effectively.

Schwottke, G. H.↗

Interaction of Glide Dislocations with Extended Precipitates in Mg-Nd alloys

The unit processes of precipitate-dislocation interaction in dilute Mg-Nd alloys are elucidated through in situ indentation experiments in TEM. Results suggest that pinned dislocations can glide along the broad facets of extended β1 precipitates, a common strengthening phase in Mg- rare earth (RE) alloys. A dislocation-theory based analysis suggests that the shape, spacing and orientation (with respect to the glide plane) of β1 precipitates may favor glide of pinned dislocations along interfaces as opposed to the classical mechanism of bowing and looping around the precipitate.

36 MATERIALS SCIENCE↗

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗

Nano-cavities observed in a 316SS PWR Flux Thimble Tube Irradiated to 33 and 70 dpa

The radiation-induced microstructure of a cold-worked 316SS flux thimble tube from an operating pressurized water reactor (PWR) was examined. Two irradiated conditions, 33 dpa at 290ºC and 70 dpa at 315ºC were examined by transmission electron microscopy. The original dislocation network had completely disappeared and was replaced by fine dispersions of Frank loops and small nano-cavities at high densities. The latter appear to be bubbles containing high levels of helium and hydrogen. An enhanced distribution of these nano-cavities was found at grain boundaries and may play a role in the increased susceptibility of the irradiated 316SS to intergranular failure of specimens from this tube during post-irradiation slow strain rate testing in PWR water conditions.

Edwards, Danny J↗

A discrete dislocation dynamics study of precipitate bypass mechanisms in nickel-based superalloys

Order strengthening in nickel-based superalloys is associated with the extra stress required for dislocations to bypass the $\gamma'$ precipitates distributed in the $\gamma$ matrix. Depending on the operating conditions and microstructure, a rich variety of bypass mechanism has been identified, with various shearing and Orowan looping processes gradually giving way to climb bypass as the operating conditions change from the low/intermediate temperatures and high stress regime, to the high temperature and low stress regime. When anti phase boundary (APB) shearing and Orowan looping mechanisms operate, the classical picture is that, at for a given volume fraction, the bypass mechanism changes from shearing to looping with increased particle size and within a broad coexistence size window. Another possibility, which is supported by indirect experimental evidence, is that a third “hybrid” transition mechanism may operate. Here, in this paper we use discrete dislocation dynamics (DDD) simulations to study dislocation bypass mechanisms in Ni-based superalloys. We develop a new method to compute generalized stacking fault forces in DDD simulations, based on a concept borrowed from complex analysis and known as the winding number of a closed curve about a point. We use this method to study the mechanisms of bypass of a square lattice of spherical $\gamma'$ precipitates by $a/2\langle110\rangle$ {111} edge dislocations, as a function of the precipitates volume fraction and size. We show that not only the hybrid mechanism is possible, but also that it operates as the transition mechanism between the shearing and looping regimes over a wide range of precipitates volume fraction and radii. Based on our simulation results, we propose a simple model for the strength of this mechanism. We also consider the effects of a $\gamma$/$\gamma'$ lattice misfit on the bypass mechanisms, which we approximate by an additional precipitate stress computed according to Eshelby’s inclusion theory. We show that in the shearing and hybrid looping-shearing regimes, a lattice misfit generally results in an increased bypass stress. For sufficiently high lattice misfit, the critical bypass configuration in attractive dislocation-precipitates interactions changes dramatically, and the bypass stress is controlled by the pinning of the trailing dislocation on the exit side of the precipitates, similar to what has been reported in the high-temperature creep literature.

36 MATERIALS SCIENCE↗

A tantalum strength model using a multiscale approach: version 2

A continuum strength model for tantalum was developed in 2007 using a multiscale approach. This was our first attempt at connecting simulation results from atomistic to continuum length scales, and much was learned that we were not able to incorporate into the model at that time. The tantalum model described in this report represents a second cut at pulling together multiscale simulation results into a continuum model. Insight gained in creating previous multiscale models for tantalum and vanadium was used to guide the model construction and functional relations for the present model. While the basic approach follows that of the vanadium model, there are significant departures. Some of the recommendations from the vanadium report were followed, but not all. Results from several new analysis techniques have not yet been incorporated due to technical difficulties. Molecular dynamics simulations of single dislocation motion at several temperatures suggested that the thermal activation barrier was temperature dependent. This dependency required additional temperature functions be included within the assumed Arrhenius relation. The combination of temperature dependent functions created a complex model with a non unique parameterization and extra model constants. The added complexity had no tangible benefits. The recommendation was to abandon the strict Arrhenius form and create a simpler curve fit to the molecular dynamics data for shear stress versus dislocation velocity. Functions relating dislocation velocity and applied shear stress were constructed vor vanadium for both edge and screw dislocations. However, an attempt to formulate a robust continuum constitutive model for vanadium using both dislocation populations was unsuccessful; the level of coupling achieved was inadequate to constrain the dislocation evolution properly. Since the behavior of BCC materials is typically assumed to be dominated by screw dislocations, the constitutive relations were ultimately built using only the screw relations. In light of this, the screw dislocation mobility relation is chosen as the starting point for the present tantalum model. Edge dislocations are not included explicitly in the current model. A significant change from the previous models is in the functional dependence of the dislocation evolution equations. The prior multiscale models assumed that the dislocation evolution rate depended on stress as well dislocation velocity. This crated an implicit dependence on the kinetic relation and required an iterative solution for the dislocation density. In the present model the integration scheme is simplified by casting the dislocation evolution terms of strain rate and current dislocation density. The final notable change was in the transition relation from the thermally activated regime to phonon drag. Historically, and in the prior models, this transition had been through a harmonic average on the strain rates making it impossible to determine the stress directly when given the plastic strain rate. After considering alternative transition relations, it was determined that an equally suitable fit to the molecular dynamics simulation data in the transition region could be constructed by averaging stresses rather than strain rates. The end result of these enhancements is a simpler (fewer parameters) and more straight forward model formulation where the material strength can be evaluated directly when given the plastic strain rate, temperature, pressure and the dislocation density at the beginning of the time step. This greatly improves the computational efficiency and robustness over the prior models where additional iteration loops were required.

36 MATERIALS SCIENCE↗

Interpretation of Ion Irradiation and Neutron Irradiation Damage in Additively Manufactured 316 Stainless Steel using Multiscale Modeling

The accelerated adoption of nuclear energy necessitates advanced manufacturing technologies, such as additive manufacturing, to meet heightened supply chain requirements and support innovative reactor technologies. Due to the unique microstructural characteristics of additively manufactured materials under distinct solidification conditions, comprehensive evaluation of their performance in reactor environments is essential. The Advanced Materials and Manufacturing Technologies program under the Department of Energy's Office of Nuclear Energy focuses on understanding the irradiation performance and damage evolution of laser powder bed fusion 316 stainless steel, with an emphasis on integrating ion and neutron irradiation data to accelerate the development and qualification of materials for advanced nuclear reactor applications. While ion irradiation is a cost- and time-effective method, modeling and simulation are required to interpret the data for the broader range of irradiation conditions encountered in advanced reactors. In fiscal year 2025, integrated multiscale modeling and simulations were conducted to assess irradiation damage in additively manufactured 316 stainless steel. Key outcomes include predictions of chromium enrichment at grain boundaries, nickel enrichment at dislocation cell walls and void surfaces, and heterogeneous void evolution under ion and neutron irradiation conditions. Cluster dynamics simulations revealed the coarsening of voids at high irradiation temperatures and the suppression of void growth by high network dislocation density, while also demonstrating significant growth and coarsening of voids and self-interstitial atom loops at low dose rates. Machine learning-accelerated atomistic simulations highlighted the impact of the local environment and chromium concentration on vacancy diffusivity, providing key insights on the influence of composition on void swelling and radiation-induced segregation. Additionally, molecular dynamics simulations demonstrated the presence of defect production bias and a significant effect of carbon content on defect cluster behavior. These combined efforts aim to predict the performance of additively manufactured materials under various reactor conditions, supporting their qualification for nuclear reactor applications by interpreting ion irradiation data. This report underscores the potential of integrated multiscale modeling to analyze ion irradiation data in the effort to accelerate the qualification of additively manufactured materials for nuclear reactor components.

316 stainless steel↗

Microstructural Analysis of an HT9 Fuel Assembly Duct Irradiated in FFTF to 155 Dpa at 443ºC

The majority of published data on the irradiation response of ferritic/martensitic steels has been derived from simple free-standing specimens irradiated in experimental assemblies under well-defined and near-constant conditions, while components of long-lived fuel assemblies are more complex in shape and will experience progressive changes in environmental conditions. To insure that the resistance of HT9 to void swelling is maintained under more realistic operating conditions, this study addresses the radiation-induced microstructure of an HT9 ferritic/martensitic (F/M) steel hexagon duct that was examined following a six-year irradiation campaign of a fuel assembly in the Fast Flux Test Reactor Facility (FFTF). The calculated irradiation exposure and operating temperature of the duct location examined were ~155 dpa at ~443ºC. It was found that dislocation networks were contained predominantly a/2<111> Burgers vector. Surprisingly, for such a large irradiation dose, type a<100> interstitial loops were observed at relatively high density. Additionally, a high density of precipitation was observed. These two microstructural characteristics may have contributed to the rather low swelling level of 0.3%. It appears that the inherent swelling resistance of this alloy observed in specimens irradiated under non-varying experimental conditions is not significantly degraded compared to time-dependent variations in neutron flux-spectra, temperature and stress state that are characteristic of actual reactor components.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Unraveling cyclic deformation mechanisms of a rolled magnesium alloy using in situ neutron diffraction

In the current study, the deformation mechanisms of a rolled magnesium alloy were investigated under cyclic loading using real-time in situ neutron diffraction under a continuous-loading condition. The relationship between the macroscopic cyclic deformation behavior and the microscopic response at the grain level was established. The neutron diffraction results indicate that more and more grains are involved in the twinning and detwinning deformation process with the increase of fatigue cycles. The residual twins appear in the early fatigue life, which is responsible for the cyclic hardening behavior. The asymmetric shape of the hysteresis loop is attributed to the early exhaustion of the detwinning process during compression, which leads to the activation of dislocation slips and rapid strain-hardening. The critical resolved shear stress for the activation of tensile twinning closely depends on the residual strain developed during cyclic loading. In the cycle before the sample fractured, the dislocation slips became active in tension, although the sample was not fully twinned. The increased dislocation density leads to the rise of the stress concentration at weak spots, which is believed to be the main reason for the fatigue failure. Furthermore, the deformation history greatly influences the deformation mechanisms of hexagonal-close-packed-structured magnesium alloy during cyclic loading.

36 MATERIALS SCIENCE↗