Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Control of Weld Residual Stress in a Thin Steel Plate through Low Transformation Temperature Welding Consumables

Low transformation temperature welding (LTTW) consumables are characterized by a low martensite start temperature and a large fraction of martensite forming in the weld. It can efficiently reduce the tensile residual stress because the volume expansion associated with the martensitic transformation compensates for the thermal contraction during cooling. In this work, a LTTW wire, designated as EH200B, was created for the arc welding of advanced high-strength steel thin plates. In comparison to conventional ER70S-3 wires, this LTTW wire generated an opposite distortion pattern. Neutron diffraction measurements along the center thickness of the welded plates showed the maximum residual stress along the longitudinal direction (LD) in the weld region, and the heat-affected zone (HAZ) immediately adjacent to the weld region was reduced from ~330 MPa to below 240 MPa by using the LTTW wire. A finite element (FE) model was developed to predict the residual stress distributions of the plates welded under these two wires. The simulation results showed reasonable agreement with the volume-average neutron diffraction data. Compressive residual stress in the weld region using the LTTW wire was predicted by the FE method. Electron backscattered diffraction and x-ray diffraction measurements confirmed ~90% martensite was present in the LTTW weld. The fatigue life of DP980 steel lap joint panels using EH200B wire nearly doubled that of ER70S-3 wire. This improvement was attributed to the high strength and low LD residual stress in the weld and HAZ immediately adjacent to the weld.

36 MATERIALS SCIENCE↗

Transmission EBSD (t-EBSD) as Tool to Investigate Nanostructures in Superconductors

The transmission electron backscatter diffraction (t-EBSD) technique has proven to be an indispensable tool for the analysis of microstructures of superconducting samples, both high-T{sub c} samples (YBa{sub 2}Cu{sub 3}O{sub y}, Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8}) as well as MgB{sub 2} or iron-based materials. The knowledge of the grain boundary properties (misorientation, length, width) is essential for the further optimization of sample performance. Any addition of secondary phase(s) to improve the flux pinning properties is required to be of nanometer dimensions, so the higher achievable resolution and the better imaging properties are important to obtain reasonably high image quality to enable automated orientation mapping. The orientation maps reveal not only the location and the shape of the inclusions within the superconducting matrix or at the grain boundaries but also their influence on the surrounding superconducting matrix, which also plays an important role in flux pinning. In the case of sintered MgB{sub 2} bulk samples, the demand for higher critical current densities leads to MgB{sub 2} grains in the 100-nm range, which is already difficult to be studied by means of conventional EBSD. Furthermore, t-EBSD is useful for the analysis of specific microstructures of unconventional superconductors like superconducting foams or superconducting nanowire networks.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An overview of HR-EBSD techniques for mapping local stress and dislocations in crystalline materials at sub-micron resolution

High resolution electron backscatter diffraction (HR-EBSD) is a technique used to map elastic strain, crystallographic orientation and dislocation density in a scanning electron microscope. Here, this review covers the background and mathematics of this technique, contextualizing it within the broader landscape of EBSD techniques and other materials characterization methods. Several case studies are presented showing the application of HR-EBSD to the study of plasticity in metals, failure analysis in microelectronics and defect quantification in thin films. This is intended to be a comprehensive resource for researchers developing this technique as well as an introduction to those wishing to apply it.

Ruggles, Timothy J. [Sandia National Laboratories ↗

Influence of sputter rate and crystal orientation on the distribution of carbon in polycrystalline copper surfaces treated by plasma immersion ion implantation

The sputter rate influences the resulting thickness of the carbon containing layer within a surface that was treated by plasma immersion ion implantation. Choosing a polycrystalline substrate with rather large crystals and a material with an inherent high sputter rate, inhomogeneous distributions of carbon over the substrate area due to different thicknesses of the incorporated carbon can be detected. A correlation of three factors namely the carbon x-ray intensity in electron probe microanalysis, the thickness of the carbon layer, and the sputter rate in depth profiling measurements via secondary ion mass spectrometry can be shown. Essential for these factors is the crystal orientation that is visualized by mapping via electron backscatter diffraction. The differences in carbon content due to the orientation are most likely one of the reasons that the adhesion of diamond-like carbon films on copper does not improve with an interlayer of implanted carbon.

36 MATERIALS SCIENCE↗

Thickness-Dependent Defect Structure of Epitaxial Silicon Thin Films Deposited by Hot-Wire Chemical Vapor Deposition

In this work, we study the defect structure of epitaxial film silicon grown by hot-wire chemical vapor deposition (HWCVD) on Si wafers, as a function of film thickness. We used scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) to investigate the distribution, type, and composition of the defects. To investigate the crystallographic structure, we used electron backscattering diffraction (EBSD) on the surface and cross sections of the samples. We observed that, as desired, the films grew epitaxially, and that there was an increase in the density of defects as the film thickness increased. One of the most dominant types of defects grows as long columns, reaching many micrometers in diameter at the surface. EBSD showed that these defects were composed of randomly oriented polycrystalline-silicon grains. To study the electrical nature of the film and defects, we used conductive atomic force microscopy (C-AFM), which provides information on film conductivity with high-spatial resolution. C-AFM showed that the columnar defects have much lower conductivity than the surrounding Si thin film. In this work, we show how the concentration and distribution of the defects change as the film thickness increases, and investigate their electrical properties. Finally, we discuss how the defect structure might impact solar cells made with this material.

14 SOLAR ENERGY↗

Second Annual Progress Report on Correlation Between Microstructure and Mechanical Properties of Neutron-Irradiated Ferritic-Martensitic and Austenitic Steels

Ferritic-martensitic steels G92-2b (an optimized Grade 92 heat), NF616 and T91, and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) and the Advanced Test Reactor (ATR) of Idaho National Laboratory (INL). Selected G92-2b samples were irradiated up to 14.66 dpa in the HFIR at two temperature ranges: 400–496.7°C and 683.3– 720°C. NF616 and T91 were irradiated in the ATR up to 8.16 dpa with the irradiation temperatures ranged from 241°C to 447.5°C. Alloy 800H and 800H-TMP samples were irradiated in both the HFIR and the ATR. Selected 800H and 800H-TMP samples had HFIR irradiation to 1.28 dpa at 580°C and ATR irradiation up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in the Low Activation Materials Design and Analysis (LAMDA) laboratory. Radiation-hardening of G92-2b was observed at the lower doses and lower irradiation temperatures (400- 496.7°C), with GB03 (0.52 dpa at 400°C) and GB04 (7.44 dpa at ~490°C) showing ~12% and ~8% hardening, respectively. Softening by ~14% was observed for GB05 (14.66 dpa at 496.7°C). Radiationsoftening of G92-2b was more prevalent at the higher irradiation temperatures (683.3-~720°C), with GB10 (0.46 dpa at 683.3°C), GB11 (7.44 dpa at ~720°C), and GB12 (14.63 dpa at ~720°C) showing ~8%, ~8%, and ~40% softening, respectively. Radiation-hardening of NF616 and T91 was observed with the hardness increased by ~37% to ~65% depending on the irradiation doses and irradiation temperatures. Within the studied irradiation conditions of NF616 and T91, samples with a higher dose had a larger hardness after irradiation. All the tested alloy 800H and 800H-TMP samples in this work showed radiation-hardening by ~96±7% to ~152±10%. Alloy 800H-TMP tended to have slightly smaller radiation-hardening than alloy 800H. The fractography results of G92-2b sample GB03, GB10, and GB11, together with the previously characterized fractography of GB04, GB05, and GB12, indicated that the ductility of G92-2b was maintained up to 14.66 dpa at the lower irradiation temperatures of 400-496.7°C, while some loss of ductility (less necking) was observed for higher doses at the higher irradiation temperatures of 683.3-720°C. This agrees with the previously reported tensile test results of G92-2b, where the elongation of G92-2b was reduced at higher doses at the higher irradiation temperatures. Dimple sizes increased at higher doses, which are more evident at the higher irradiation temperatures of 683.3-~720°C. The fractography of NF616 sample D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for sample D2, while ductile failure for samples D4 and D6. Fractography of alloy 800H and 800H-TMP samples in various irradiation conditions showed ductile failure with obvious necking. Dimples were observed, with some of them containing large Ti-rich particles, in all the 800H/800H-TMP samples. Electron backscatter diffraction characterization of GB12 indicated the recovery of the lath structure, which was generally replaced by an equiaxed grain structure. Transmission electron microscopy (TEM) characterization showed the presence of frequent M 23 C 6 (M = primarily Cr), MX (M = primarily V), spherical Nb(C,N) precipitates, and occasional Laves phase precipitates in the G92-2b samples. MX precipitates with sizes of 20-30 nm were observed at boundaries of smaller grains, indicating the pinning effect of the V-rich precipitates. The lath structure recovery was more evident at the higher irradiation temperatures (683.3-~720°C), with decreased densities of line dislocations and M23C6 precipitates. The irradiated T91 (TA04) showed the growth of M23C6 precipitates to 101 ± 40 nm from the initial 68 ± 22 nm in the unirradiated condition. Dislocation loops of both {100} and {111} types were present in TA04. TEM characterization was also performed on the irradiated 800H (N4, N5, N6, and AR2) and 800H-TMP (P4, P5, P6, and HG1). Accumulation of M 23 C 6 precipitates at grain boundaries was observed in all the xii 800H/800H-TMP samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in the irradiated 800H-TMP. Some Ti(C,N) precipitates are embedded in the M 23 C 6 precipitates, maintaining specific orientation relationships between the precipitates and between the precipitate and matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all the 800H/800H-TMP samples, with EDS Si maps tending to have a lower contrast in 800H-TMP samples. Atom probe tomography was conducted on the same samples, supported by a Rapid Turnaround Examination project under Nuclear Science User Facilities. The results are being analyzed to be integrated with the TEM results for a confident description of the γ’ precipitates. Dislocation loops also formed in all the 800H/800H-TMP samples. The density and the average size of dislocation loops were quantified to be in the order of 10 22 – 10 23 m -3 and 11.7 – 15.9 nm, respectively, in the ATR-irradiated 800H/800H-TMP samples. The loop densities in irradiated 800H were higher than that in irradiated 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

Statistics of High Purity Nickel Microstructure From High Energy X-ray Diffraction Microscopy

We have measured and reconstructed via forward modeling a small volume of microstructure of high purity, well annealed nickel using high energy x-ray diffraction microscopy (HEDM). Statistical distributions characterizing grain orientations, intra-granular misorientations, and nearest neighbor grain misorientations are extracted. Results are consistent with recent electron backscatter diffraction measurements. Peaks in the grain neighbor misorientation angle distribution at 60 degrees ({Sigma}3) and 39 degrees ({Sigma}9) have resolution limited widths of {approx} 0.14 degree FWHM. The analysis demonstrates that HEDM can recover grain and grain boundary statistics comparable to OIM volume measurements; more extensive data sets will lead to full, five parameter grain boundary character distributions. Due to its non-destructive nature, HEDM can then watch, both statistically and through tracking of individual grains and boundaries, the evolution of such distributions with processing of the sample.

43 PARTICLE ACCELERATORS↗

Quantification of retained austenite by X-ray diffraction and saturation magnetization in a supermartensitic stainless steel

The good performance of supermartensitic stainless steels is strongly dependent on the volume fraction of retained austenite at room temperature. The present work investigates the effect of secondary tempering temperatures on this phase transformation and quantifies the amount of retained austenite by X-ray diffraction and saturation magnetization. The steel samples were tempered for 1 h within a temperature range of 600–800 °C. The microstructure was characterized using scanning electron microscopy and electron backscatter diffraction. Results show that the amount of retained austenite decreased with increasing secondary tempering temperature in both quantification methods. - Highlights: • The phase transformation during secondary tempering temperatures was observed. • Phases were quantified by X-ray diffraction and DC-saturation magnetization. • More retained austenite forms with increasing secondary tempering temperature. • The retained austenite is mainly located at the grain and lath boundaries.

36 MATERIALS SCIENCE↗

Microstructural characterization of nitrided beta Ti-Mo alloys at 1400 deg. C

In this work, the two Ti{sub 92}Mo{sub 8} and Ti{sub 84}Mo{sub 16} alloy compositions were gas nitrided at 1400 deg. C. The microstructure and the chemical composition of the gas nitrided surfaces were investigated by scanning electron microscopy and by electron probe microanalysis. Two internal needle-like nitride precipitates, {alpha}-(Ti,N) and {delta}-TiN{sub 0.3}, were observed. Their crystallographic orientation relationships in the {beta} matrix were determined by electron backscattering diffraction.

36 MATERIALS SCIENCE↗

Generalizable Image Segmentation for Microstructure Characterization Through Integrated SEM and EBSD Analysis

We demonstrate generalizable semantic segmentation using minimal ground truth data. Correlated scanning electron microscopy (SEM) images and electron backscatter diffraction (EBSD) measurements of frictionstir processed 316L stainless steel plates were used to train deep learning models for grain boundary segmentation. Secondary electron (SE) imaging taken at an accelerating voltage of 10 keV correlated to EBSD-derived grain boundaries produced the best performing model. Notably, an ensemble of three models trained on a single SE image produced accurate segmentation over a series of BSE images of samples manufactured under different processing parameters, with a resultant mean absolute error in grain size of 0.34 µm. The striking generalizability of the models likely results from the similar escape depths of the SE training input and the EBSD training output and the reduced probability of dislocation artifacts appearing in the image. This finding highlights the importance of considering the physical principles behind imaging in the development of robust segmentation models for microstructure characterization.

Taufique, Mohammad Fuad Nur↗

Effect of carbon content on solidification behaviors and morphological characteristics of the constituent phases in Cr-Fe-C alloys

A combination of transmission electron microscopy, electron backscatter diffraction and wavelength dispersive spectrum has been used to identify crystal structure, grain boundary characteristic and chemical composition of the constituent phases in Cr-Fe-C alloys with three different carbon concentrations. Depending on the three different carbon concentrations, the solidification structures are found to consist of primary {alpha}-phase and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-18.4Fe-2.3 C alloy; primary (Cr,Fe){sub 23} C{sub 6} and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-24.5Fe-3.8 C alloy and primary (Cr,Fe){sub 7} C{sub 3} and [{alpha} + (Cr,Fe){sub 7} C{sub 3}] eutectic in Cr-21.1Fe-5.9 C alloy, respectively. The grain boundary analysis is useful to understand growth mechanism of the primary phase. The morphologies of primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides are faceted structures with polygonal shapes, different from primary {alpha}-phase with dendritic shape. The primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides with strong texture exist a single crystal structure and contain a slight low angle boundary, resulting in the polygonal growth mechanism. Nevertheless, the primary {alpha}-phase with relative random orientation exhibits a polycrystalline structure and comprises a massive high-angle boundary, caused by the dendritic growth mechanism. - Highlights: Black-Right-Pointing-Pointer Microstructures of the as-clad Cr-based alloys are characterized by TEM. Black-Right-Pointing-Pointer EBSD technique has been use to characterize the grain boundary of primary phases. Black-Right-Pointing-Pointer We examine transitions in morphology about the primary phases. Black-Right-Pointing-Pointer Morphologies of primary carbides are polygonal different from primary {alpha}-phase. Black-Right-Pointing-Pointer Solidification structures rely on C concentrations in Cr-Fe-C alloy.

36 MATERIALS SCIENCE↗

Directly Linking Low-Angle Grain Boundary Misorientation to Device Functionality for GaAs Grown on Flexible Metal Substrates

A new growth method to make highly oriented GaAs thin films on flexible metal substrates has been developed, enabling roll-to-roll manufacturing of flexible semiconductor devices. The grains are oriented in the <001> direction with <1 degree misorientations between them, and they have a comparable mobility to single-crystalline GaAs at high doping concentrations. At the moment, the role of low-angle grain boundaries (LAGBs) on device performance is unknown. A series of electron backscatter diffraction (EBSD) and cathodoluminesence (CL) studies reveal that increased doping concentrations decrease the grain size and increase the LAGB misorientation. Cross-sectional scanning transmission electron microscopy (STEM) reveals the complex dislocation structures within LAGBs. Most importantly, a correlative EBSD/electron beam-induced current (EBIC) experiment reveals that LAGBs are carrier recombination centers and that the magnitude of recombination is dependent on the degree of misorientation. The presented results directly link increased LAGB misorientation to degraded device performance, and therefore, strategies to reduce LAGB misorientations and densities would improve highly oriented semiconductor devices.

36 MATERIALS SCIENCE↗

Investigation of the accuracy of modeling the orientation distribution function of polycrystalline materials from individual orientations

The accuracy of reconstructing the orientation distribution function of grains in polycrystalline materials by the kernel method from a set of individual orientations has been studied. In particular, the influence of choosing the smoothing kernel in the kernel method and the influence of the dependence on the resulting distribution are taken into account. The rotations obeying the normal distribution on the group SO(3) and obtained by the statistical test method are used as an orientation set. Some aspects of electron backscattering diffraction measurements are considered. This problem is urgent in view of the expanding potential of the experimental study of the texture of polycrystalline materials, especially for electron microscopy, which makes it possible to measure the orientations of individual grains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Texture of Cobalt Germanides on Ge(100) and Ge(111) and Its Influence on the Formation Temperature

The phase formation of cobalt germanides on Ge(100) and Ge(111) substrates was investigated using in situ X-ray diffraction, starting from room-temperature sputter-deposited Co films. The formation temperature of the CoGe{sub 2} phase was dependent on the substrate orientation. X-ray pole figures and electron backscatter diffraction measurements were used to identify the texture and microstructure of the CoGe{sub 2} and the preceding Co{sub 5}Ge{sub 7} films. A significant difference in preferential orientation was found in the Co{sub 5}Ge{sub 7} films, depending on the substrate orientation. This influences the formation temperature of the CoGe{sub 2} and results in the coexistence of Co{sub 5}Ge{sub 7} and CoGe{sub 2} on Ge(111) in a large temperature window.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ deformation of antigorite-olivine two-phase mixtures: Implications for dynamics and seismic anisotropy in the mantle wedge

Water released from hydrous minerals in subducting slabs reacts with the overlying plate, resulting in widespread serpentinization in the mantle wedge. Deformation of serpentinized peridotites has been invoked to explain forearc seismic anisotropy, yet studies of the mechanical properties and deformation behaviors of serpentine-bearing multiphase aggregates remain limited. Here we deformed olivine-antigorite mixtures containing 70, 50, and 20 vol.% of antigorite at 2.5 – 7.6 GPa, 673 K and strain rates of ∼10 –5 –10 –4 s –1 . Elasto-viscoplastic self-consistent simulations, constrained by synchrotron X-ray diffraction (XRD) data, were used to estimate lattice strain, stress–strain partitioning, crystallographic preferred orientations (CPO) development, and aggregate strength. Selected run products were also analyzed by electron backscatter diffraction for comparison with the CPO results obtained from XRD experiments. We found olivine transitions from A- or B-type to C-type when antigorite fraction drops to 20 vol.%, coinciding with a microstructural change from interconnected weak layers to a load-bearing framework (LBF). An additional run on a sample Atg50/Ol50 with preexisting microstructures suggested the formation of LBF was promoted by these microstructures, although the preexisting antigorite CPO has been overprinted at 20.8 % strain and could be erased completely by subsequent deformation in nature. Estimated viscosity of the two-phase mixtures suggests that low-degree serpentinization (≤20 %) in the mantle wedge may increase the strength of olivine-rich peridotite and hinder slab-mantle decoupling, whereas high-degree serpentinization (≥50–70 %) weakens the peridotite and favors decoupling if sufficient viscosity contrast (>10) develops. Seismic anisotropy shows a nonlinear dependence on antigorite fraction: antigorite CPO governs the anisotropy of the mixtures with ≥50 vol.% antigorite, whereas olivine CPO dominates at low fractions (∼20 vol.%). The presence of pre-existing microstructures reduces seismic anisotropy of the deformed mixtures, however the persistence of pre-existing CPO in actively subducting slabs remains uncertain, making their significance over geological timescales questionable.

Crystallographic preferred orientation↗

Effects of Sn microalloying on cold rolling and recrystallization textures and microstructure of a ferritic stainless steel

Highlights: • Sn microalloying contributes to the enhancement in cold rolling texture intensity and the acceleration in cold rolling texture transformation. • Sn microalloying promotes the recrystallization process, and recrystallization occurs preferentially in steel with Sn compared with Sn-free steel. • Sn microalloying inhibits the growth of recrystallized grains, and the finer grains are obtained in steel with Sn. - Abstract: We investigated the effects of Sn microalloying on cold rolling and recrystallization textures and microstructure of a ferritic stainless steel. The as-received hot rolled sheets were cold rolled at 10%–90% reductions; the sheets cold rolled up to an 80% reduction were annealed at 740–880 °C for 5 min. For comparison, the cold rolling and recrystallization textures of the steel sheets with and without Sn were determined with the conventional X-ray diffraction method. The cold rolling and recrystallization metallographic microstructures were measured by scanning electron microscope and optical microscope, and the crystal orientation maps of the cold rolled and annealed samples were observed by electron backscattered diffraction. The micro-hardness was determined using a digital micro-hardness tester. Our results show that Sn microalloying in a medium chromium ferritic stainless steel plays multiple roles in the cold rolling and recrystallization processes. Sn micrcoalloying contributes to the enhancement in cold rolling texture intensity and the acceleration in cold rolling texture transformation. Sn microalloying is beneficial in promoting the recrystallization process. Recrystallization occurs preferentially in the ferritic stainless steel with Sn. Sn microalloying plays an important role in inhibiting the growth of recrystallized grains. The finer grains are obtained in ferritic stainless steel with Sn when annealing at high temperatures.

36 MATERIALS SCIENCE↗

Retaining Geochemical Signatures during Aragonite-Calcite Transformation at Hydrothermal Conditions

Transformation of aragonite, a mineral phase metastable at Earth’s surface, to calcite widely occurs in both sedimentary and metamorphic systems with the presence of an aqueous phase. The transformation process can affect geochemical signatures of aragonite (a protolith). This study focused on quantification of the retention of Mg/Ca and Sr/Ca ratios, and δ18O during the transformation process as well as evaluation of the transformation rate. To investigate the effect of transformation from aragonite to calcite on elemental and stable isotope ratios, we conducted a series of experiments in NaCl solutions at temperatures between 120 and 184 °C. Two additional experiments at 250 °C were conducted to estimate the transformation rate of aragonite to calcite. Protolith materials consist of (1) synthetic (Mg; Sr-bearing or non-Mg; Sr bearing) needle-shaped microcrystals of aragonite (<5 µm in size) and (2) larger chips (>100 µm in size) of natural aragonite. X-ray diffraction (XRD) showed that microcrystals successfully transformed to calcite within 30 h and scanning electron microscopy (SEM) yielded a change in the crystal size to >10 µm in rhombohedral shape. Electron backscatter diffraction (EBSD) of the larger aragonite chips showed that transformation to randomly oriented calcite occurred at the rims and along the cracks while the core retained an aragonite crystal structure. Isotope-ratio mass spectrometry (IRMS) analyses showed that calcite δ18O was controlled by temperature and δ18O of the solution. The obtained calibration curve of isotope fractionation factor versus temperature is consistent with other studies. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses showed that calcite partially or completely retained Mg/Ca and Sr/Ca ratios through the transformation.

58 GEOSCIENCES↗

Elucidating the corrosion mechanism of Ni-based superalloys in the presence of uranium-containing chloride molten salt

The United States Department of Energy (DOE) is committed to the advancement of nuclear reactor technology through initiatives such as the Advanced Reactor Development Program (ARDP), in an effort to diversify the United States energy portfolio towards more sustainable energy options. The ARDP includes demonstration by industry partners of molten chloride fast reactors (MCFRs). Construction of MCFRs requires qualified nuclear structural materials. Unfortunately, there are no current materials that are fully qualified by the Nuclear Regulatory Commission for the construction of molten salt reactors, including MCFRs. Adapting current structural material qualifications requires expansion of our current knowledgebase on the property-performance relationships regarding corrosion performance. In this investigation, we assess microstructural changes in a Ni-based superalloy after exposure to a UCl3¬-containing chloride salt eutectic mixture through a correlated multi-modal approach combining several advanced characterization techniques, including scanning electron microscopy/focused ion beam (SEM/FIB) and transmission electron microscopy (TEM). SEM/FIB analysis will illustrate changes in elemental composition, microstructure, and isotopic information acquired from energy x-ray dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), and secondary ion mass spectroscopy (SIMS), respectively. This information will then aid in identifying localized regions to elucidate the corrosion mechanism with TEM through a combination of electron diffraction, electron energy loss spectroscopy (EELS), and additional EDS. The findings from this investigation will further expand our assessment of the corrosion performance of structural materials in molten salt chloride systems, aiding to developing fully qualified materials for construction of MCFRs.

36 MATERIALS SCIENCE↗