Search NASA⌕ Search

SEARCH · Search NASA

Results for “hardness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

On the Origin of the Hard X-Ray Excess of High-Synchrotron-Peaked BL Lac Object Mrk 421

For the first time, Kataoka and Stawarz reported a clear detection of a hard X-ray excess, above ≳20 keV, in the high-synchrotron-peaked BL Lac object Mrk 421. We find that this feature may not be produced by the low-energy part of the same electron population that produced the Fermi/LAT γ-ray. Because of that, it is required that the power-law electron energy go down to γ{sub min}≈19, which predicts a very strong radio emission (radio flux larger than the observed), even considering the synchrotron self-absorption effect. We investigate the possibility of this excess being produced from the spine/layer jet structure, which has been clearly detected in Mrk 421. We find that (1) similar to one-zone modeling, the spine emissions provide good modeling of the broadband spectral energy distribution, except for the hard X-ray excess; and (2) the hard X-ray excess can be well represented by the synchrotron photons (from the layer) being inverse Compton scattered by the spine electrons.

79 ASTRONOMY AND ASTROPHYSICS↗

X-Ray Timing Analysis of Cyg X-3 Using AstroSat/LAXPC: Detection of Milli-hertz Quasi-periodic Oscillations during the Flaring Hard X-Ray State

We present here results from the X-ray timing and spectral analysis of the X-ray binary Cyg X-3 using observations from the Large Area X-ray proportional Counter on board AstroSat . Consecutive light curves observed over a period of one year show the binary orbital period of 17253.56 ± 0.19 s. Another low-amplitude, slow periodicity of the order of 35.8 ± 1.4 days is observed, which may be due to the orbital precession as suggested earlier by Molteni et al. During the rising binary phase, power density spectra from different observations during the flaring hard X-ray state show quasi-periodic oscillations (QPOs) at ∼5–8 mHz, ∼12–14 mHz, and ∼18–24 mHz frequencies at the minimum confidence of 99%. However, during the consecutive binary decay phase, no QPO is detected up to 2 σ significance. Energy-dependent time-lag spectra show soft lag (soft photons lag hard photons) at the mHz QPO frequency and the fractional rms of the QPO increases with the photon energy. During the binary motion, the observation of mHz QPOs during the rising phase of the flaring hard state may be linked to the increase in the supply of the accreting material in the disk and corona via stellar wind from the companion star. During the decay phase, the compact source moves in the outer wind region causing the decrease in supply of material for accretion. This may cause weakening of the mHz QPOs below the detection limit. This is also consistent with the preliminary analysis of the orbital phase-resolved energy spectra presented in this paper.

79 ASTRONOMY AND ASTROPHYSICS↗

Hard X-Ray Emission from the M87 AGN Detected with NuSTAR

M87 hosts a 3–6 billion solar mass black hole with a remarkable relativistic jet that has been regularly monitored in radio to TeV bands. However, hard X-ray emission ≳10 keV, which would be expected to primarily come from the jet or the accretion flow, had never been detected from its unresolved X-ray core. We report NuSTAR detection up to 40 keV from the the central regions of M87. Together with simultaneous Chandra observations, we have constrained the dominant hard X-ray emission to be from its unresolved X-ray core, presumably in its quiescent state. The core spectrum is well fitted by a power law with photon index Γ=2.11{sub −0.11}{sup +0.15}. The measured flux density at 40 keV is consistent with a jet origin, although emission from the advection-dominated accretion flow cannot be completely ruled out. The detected hard X-ray emission is significantly lower than that predicted by synchrotron self-Compton models introduced to explain emission above a GeV.

79 ASTRONOMY AND ASTROPHYSICS↗

Characterization of Radiation Hard Silicon Materials

Segmented silicon detectors are widely used in modern high-energy physics (HEP) experiments due to their excellent spatial resolution and well-established manufacturing technology. However, in such experiments the detectors are exposed to high fluences of particle radiation, which causes irreversible crystallographic defects in the silicon material. Since 1990's, considerable amount of research has gone into improving the radiation hardness of silicon detectors. One very promising approach is to use magnetic Czochralski silicon (MCz-Si) that has been found to be more radiation hard against charged hadrons than traditional Float Zone silicon material (Fz-Si) used in the current HEP applications. Other approaches include operating the devices at cryogenic temperatures and designing special detector structures such as p-type detectors or semi-3D detectors. In order to demonstrate that the developed technologies are suitable for the HEP experiments, it is necessary to extensively characterize the potentially radiation hard detectors. We have an excellent instrument for this, the Cryogenic Transient Current Technique (C-TCT) measurement setup, which is an effective research tool for studying heavily irradiated silicon detectors. With the C-TCT setup it is possible to extract the full depletion voltage, effective trapping time, electric field distribution and the sign of the space charge in the silicon bulk in the temperature range of 45-300 K. This articles presents a description of this setup and measurement results from detectors processed of MCz-Si.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The Effect of Total Ionizing Dose Degradation of Laptop Hard Disks

A series of total ionizing dose (TID) measurements were performed on commercial hard drives to explore the possible uses of the devices for the high radiation mission, and to help the understanding of the reliability of current hard drive technology. Three different models from three major manufacturers were tested with the aid of a commercial hard drive test system.

laptop computers↗

The Effect of Various Quenchants on the Hardness and Microstructure of 60-NITINOL

The effect of various quenching media on the hardness and microstructure of 60 NITINOL (60 NiTi) were evaluated. Specimens of 60 NiTi were heat treated in air at 1000 degC for 30 min or 2 hr, then quench cooled by one of seven different methods. The microstructure and hardness of this material was examined post heat treatment. The results indicated that the quench method had little effect on the resulting hardness and microstructure of 60 NiTi.

Quench↗

Hardness and Second Phase Percentage of Ni-Ti-Hf Compounds After Heat Treatment at 700C

The Vickers hardness and second phase precipitation of three ternary intermetallic Ni-Ti-Hf compounds containing either 1, 3 or 5 at.% Hf were compared to 60-Nitinol (55 at.% Ni - 45 at.% Ti). Heat treatment either at 700 C or with a subsequent aging step, hardened the 3 and 5 at.% Hf-containing ternaries to approximately 620 HV (56 HRC). Heat treatment increased the hardness of the 1 at.% Hf compound by more than 25 percent. Average hardness of the 3 and 5 at.% Hf ternaries, though higher than that of the binary Ni-Ti or the Ni-Ti-Hf compound containing 1 at.% Hf, appeared to be fairly insensitive to the different heat treatments. There was a drastic reduction of fatigue-enhancing second phase precipitates for the 5 at.% Hf ternaries compared to the other compounds. These results should guide materials selection for development of aerospace componentry.

intermetallics↗

Influence of Feed Rate on Microstructure and Hardness of Conventionally Spun-formed Al 6061-O Plate

The effect of feed rate on the hardness and microstructure of a 7.35-mm-thick section from a spin-formed Al 6061 cylinder is investigated via microhardness mapping and electron backscatter diffraction (EBSD) analysis. The through-thickness hardness and microtexture profiles, corresponding to a true thickness strain of ≈ 0.3, are utilized to evaluate microstructural variations that could influence mechanical anisotropy and spin formability. The microhardness data reveal distinct gradients from the outer to the inner mold line that vary with feed rate and may be a function of the level of forming strain in the material. The microtextural mapping data expose a minor influence from feed rate, but contain trends through the material cross-section that suggest variations in the location-dependent stress states. The results demonstrate for the first time that the relationship between spin forming deformation and hardness or texture variations can be exploited to optimize processing parameters and mechanical response.

Spin forming↗

SUPER HARD SURFACED POLYMERS

High energy ion beam surface treatments were applied to a selected group of polymers. Of the six materials in the present study, four were thermoplastics (polycarbonate, polyethylene, polyethylene terephthalate, and polystyrene) and two were thermosets (epoxy and polyimide). The particular epoxy evaluated in this work is one of the resins used in formulating fiber reinforced composites for military helicopter blades. Measures of mechanical properties of the near surface regions were obtained by nanoindentation hardness and pin on disk wear. Attempts were also made to measure erosion resistance by particle impact. All materials were hardness tested. Pristine materials were very soft, having values in the range of approximately 0.1 to 0.5 GPa. Ion beam treatment increased hardness by up to 50 times compared to untreated materials. For reference, all materials were hardened to values higher than those typical of stainless steels. Wear tests were carried out on three of the materials, PET, PI and epoxy. On the ion beam treated epoxy no wear could be detected, whereas the untreated material showed significant wear.

36 MATERIALS SCIENCE↗

STRAIN CORRELATIONS IN ALLOY 690 MATERIALS USING ELECTRON BACKSCATTER DIFFRACTION AND VICKERS HARDNESS

High chromium, nickel-base Alloy 690 exhibits an increased resistance to stress corrosion cracking (SCC) in pressurized water reactor (PWR) primary water environments over lower chromium alloy 600. As a result, Alloy 690 has been used to replace Alloy 600 for steam generator tubing, reactor pressure vessel nozzles and other pressure boundary components. However, recent laboratory crack-growth testing has revealed that heavily cold-worked Alloy 690 materials can become susceptible to SCC. To evaluate reasons for this increased SCC susceptibility, detailed characterizations have been performed on as-received and cold-worked Alloy 690 materials using electron backscatter diffraction (EBSD) and Vickers hardness measurements. Examinations were performed on cross sections of compact tension specimens that were used for SCC crack growth rate testing in simulated PWR primary water. Hardness and the EBSD integrated misorientation density could both be related to the degree of cold work for materials of similar grain size. However, a microstructural dependence was observed for strain correlations using EBSD and hardness which should be considered if this technique is to be used for gaining insight on SCC growth rates

Alloy 690↗

Design and Implementation of a Hall Effect Sensor Array Applied to Recycling Hard Drive Magnets

Rare earths are an important resource for many electronic components and technologies. Examples abound including Neodymium magnets used in mobile devices and computer hard drives (HDDs), and a variety of renewable energy technologies (e.g., wind turbines). Approximately 21,000 metric tons of Neodymium is processed annually with less than 1% being recycled. An economic system to assist in the recycling of magnet material from post-consumer goods, such as Neodymium Iron Boron magnets commonly found in hard drives is presented. A central component of this recycling measurement system uses an array of 128 Hall Effect sensors arranged in two columns to detect the magnetic flux lines orthogonal to the HDD. Results of using the system to scan planar shaped objects such as hard drives to identify and spatially locate rare-earth magnets for removal and recycling from HDDs are presented. Applications of the sensor array in other identification and localization of magnetic components and assemblies will be presented.

Hall Effect sensors↗

The Role of Titania Surface Coating by Atomic Layer Deposition in Improving Osteogenic Differentiation and Hard Tissue Formation of Dental Pulp Stem Cells

Recent studies have focused on modifying implant surface properties to improve bone regeneration and osseointegration. Herein, the role of titania surface coating in enabling dental pulp stem cells (DPSCs) differentiation and hard tissue formation is studied. Atomic layer deposition is applied at lower temperature to coat a nanolayer of titania onto hard and soft polybutadiene substrates without altering their moduli, to probe the effects of surface chemistry and substrate modulus. In the absence of titania, DPSCs prefer to attach and proliferate on the hard substrate, where particle-like biomineralization is present after 28 days in culture, whereas no biomineralization is observed on the soft substrate. Applying titania surface coating results in the improvement of adhesion and proliferation, regardless of substrate modulus, whereas cell and substrate moduli remain the same as control without titania coating. Furthermore, templated biomineralization is observed given the bone-like tissue composition by Raman analysis, in consistent with real time-polymerase chain reaction (RT-PCR) results showing upregulation of osteopontin (OPN) and bone sialoprotein (BSP), representing osteogenic differentiation. Furthermore, the results indicate that titania surface coating improved the ability to nucleate banded collagen fibers which in turn templated mineral deposits, and further induced the osteogenesis of DPSCs, regardless of its substrate modulus.

36 MATERIALS SCIENCE↗

The Multiphasic Teeth of Chiton Articulatus , an Abrasion‐Resistant and Self‐Sharpening Tool for Hard Algae Collection

Abstract Chiton articulatus is a species of mollusk living in the tropical Pacific intertidal rocky shores of Mexico. This species feeds on solid waste organic sources, including hard crustose algae that grow on rocky substrates, by grazing on them with its radula, a flexible chitinous membrane lined with mineralized major lateral teeth. In this study, the composition, morphology, and resulting mechanics of the mature teeth of this species, which have yet to be examined, are revealed. The results show the presence of multiphasic mature teeth, each consisting of aligned hard magnetite nanoparticles on the leading edge of the tooth underneath which are magnetite lamellae, followed by goethite, lepidocrocite, and eventually hydroxyapatite near the trailing edge. This multiregional structure demonstrates a gradation in hardness as well as different microstructural features integrated with tough interfaces. The combination of these microstructural and phase arrangements results in an abrasion‐resistant tough structure with a self‐sharpening ability. The results of this work will help contribute to developing new bioinspired designs while also helping to understand the evolution and feeding habits of these intriguing invertebrates.

36 MATERIALS SCIENCE↗

The Hard Ferromagnetism in FePS 3 Induced by Non‐Magnetic Molecular Intercalation

Abstract Manipulating the magnetic ground states of 2D magnets is a focal point of recent research efforts. Various methods have demonstrated efficacy in modulating the magnetic properties inherent to van der Waals (vdW) magnetic systems. Herein, the emergence of robust anisotropic ferromagnetism within antiferromagnetic FePS 3 is unveiled via intercalation with non‐magnetic pyridinium ions. A one‐step ion exchange reaction facilitates the formation of energetically favorable B‐phase and metastable P‐phase. Notably, both B‐ and P‐phases manifest hard ferromagnetic behavior, featuring substantial unsaturated coercive fields (>7 T) and high Curie temperatures (72–87 K). First‐principles calculations elucidate the pivotal role of electron transfer from pyridinium ions to FePS 3 in engineering magnetic exchange interactions. Calculated effective spin Hamiltonian corroborates the observed hard ferromagnetism in intercalated FePS 3 . This study offers crucial insights into hard magnetism in intercalated vdW materials, thereby presenting promising avenues for 2D vdW magnet‐based magnetic devices.

Ou, Yunbo↗

On Maximal Hard-Core Thinnings of Stationary Particle Processes

The present paper studies existence and distributional uniqueness of subclasses of stationary hard-core particle systems arising as thinnings of stationary particle processes. These subclasses are defined by natural maximality criteria. We investigate two specific criteria, one related to the intensity of the hard-core particle process, the other one being a local optimality criterion on the level of realizations. In fact, the criteria are equivalent under suitable moment conditions. We show that stationary hard-core thinnings satisfying such criteria exist and are frequently distributionally unique. More precisely, distributional uniqueness holds in subcritical and barely supercritical regimes of continuum percolation. Additionally, based on the analysis of a specific example, we argue that fluctuations in grain sizes can play an important role for establishing distributional uniqueness at high intensities. Finally, we provide a family of algorithmically constructible approximations whose volume fractions are arbitrarily close to the maximum.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Deposition Pressure, Nitrogen Content and Substrate Temperature on Optical and Mechanical Behavior of Nanocomposite Al-Si-N Hard Coatings for Solar Thermal Applications

Hard and optically transparent nanocomposite Al-Si-N thin films were deposited using DC magnetron sputtering at different process parameters. There was a significant effect of these parameters on the film properties affecting its mechanical and optical behavior. The nitrogen content or pressure, deposition pressure and substrate temperature strongly influence the phase formation which governs the hardness and optical transparency of the coating. Hardness was measured between 18 and 30 GPa. The band gap could be varied in the range of 3.8-4.2 eV by varying nitrogen pressures in the chamber during deposition. The films showed (0-80)% transparency in UV and visible region depending on the sputtering conditions.

36 MATERIALS SCIENCE↗

Modeling of Martensite Transformation in White Layer under Thermo-mechanical Coupling in Hard-Cutting Process

Martensite volume fraction determines the hardness and wear resistance of workpiece, predicting the martensite volume fraction of the white layer is of great significance for improving the surface quality of the workpiece. Accordingly, a theoretical model on the martensite volume fraction was developed in combination with the martensite transformation temperature model and the hard-cutting FE model. A finite element (FE) model of the hard-cutting was established to obtain the stress distribution of the workpieces. A calculation model of martensite phase transformation temperature M{sub S} under the influence of the cooling rate and stress was deduced based on the change of Gibbs free energy. A theoretical model of martensite volume fraction f{sub M} of the white layer was developed based on the M{sub S} and the FE simulations. The f{sub M} calculated by the theoretical model is in accordance with the experimental result. The effects of cutting speed, feed rate, flank wear and tool rake angle on the f{sub M} in the white layers were predicted and analyzed; the results show that the f{sub M} decreases first and then increases with the cutting speed, decreases with the feed rate and the flank wear, and increases with the tool rake angle.

36 MATERIALS SCIENCE↗

Experiments and modeling to characterize microstructure and hardness in 304L

Drawn 304L stainless steel tubing was subjected to 42 different annealing heat treatments with the goal of initializing a microstructural model to select a heat treatment to soften the tubing from a hardness of 305 Knoop to 225–275 Knoop. The amount of recrystallization and grain size caused by 18 heat treatments were analyzed via optical microscopy and image analysis, revealing the full range of recrystallization from 0 to 100%. The formation of carbides during the longer duration and higher-temperature heat treatments was monitored via transmission electron microscope evaluation. The experimental results informed a model which includes recovery, recrystallization, and grain growth to predict microstructure and hardness. After initialization of the model, it was able to predict hardness with a R 2 value of 0.95 and recrystallization with an R 2 value of 0.99. As a result, the model was then utilized in the design and testing of a heat treatment to soften the tubing.

36 MATERIALS SCIENCE↗