Search NASA⌕ Search

SEARCH · Search NASA

Results for “ionic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Ionic conductivity and the formation of cubic CaH{sub 2} in the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composite

LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites were prepared by ball milling. Their crystal structures and phase composition were investigated using synchrotron X-ray diffraction and Rietveld refinement, and their ionic conductivity was measured using impedance spectroscopy. The materials were found to form a physical mixture. The composites were composed of α-Ca(BH{sub 4}){sub 2}, γ-Ca(BH{sub 4}){sub 2} and orthorhombic LiBH{sub 4}, and the relative phase quantities of the Ca(BH{sub 4}){sub 2} polymorphs varied significantly with LiBH{sub 4} content. The formation of small amounts of orthorhombic CaH{sub 2} and cubic CaH{sub 2} in a CaF{sub 2}-like structure was observed upon heat treatment. Concurrent formation of elemental boron may also occur. The ionic conductivity of the composites was measured using impedance spectroscopy, and was found to be lower than that of ball milled LiBH{sub 4}. Electronic band structure calculations indicate that cubic CaH{sub 2} with hydrogen defects is electronically conducting. Its formation along with the possible precipitation of boron therefore has an effect on the measured conductivity of the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites and may increase the risk of an internal short-circuit in the cells. -- Graphical abstract: An Arrhenius plot of the ionic conductivity of the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites (red, blue, green). The ionic conductivity of ball milled (gray) and non-milled (black) LiBH{sub 4} is shown for comparison. The filled symbols are measured during heating runs and the empty symbols are measured during subsequent cooling runs. The conductivity of the composites is in all cases higher during cooling, most probably due to the formation of an electronically conducting layer containing defect-rich cubic CaH{sub 2}. Such layer formation could eventually lead to a short circuit in the cell and reveals a general issue of chemical stability that should be attended to in the development of solid electrolyte materials. Highlights: • The LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composite forms a physical mixture rather than a solid solution. • The formation of defect-rich, cubic CaH{sub 2} in a CaF{sub 2}-like structure is observed. • A new layer containing cubic CaH{sub 2} is conducting and may lead to a short-circuit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Syntheses, structures, and ionic conductivities of perovskite-structured lithium–strontium–aluminum/gallium–tantalum-oxides

The ionic conductivities of new perovskite-structured lithium–strontium–aluminum/gallium–tantalum oxides were investigated. Solid solutions of the new perovskite oxides, (Li{sub x}Sr{sub 1−x})(Al{sub (1−x)/2}Ta{sub (1+x)/2})O{sub 3} and (Li{sub x}Sr{sub 1−x})(Ga{sub (1−x)/2}Ta{sub (1+x)/2})O{sub 3}, were synthesized using a ball-milled-assisted solid-state method. The partial substitution of the smaller Ga{sup +3} for Ta{sup +5} resulted in new compositions, the structures of which were determined by neutron diffraction measurements using a cubic perovskite structural model with the Pm−3m space group. Vacancies were introduced into the Sr(Li) sites by the formation of solid solutions with compositions (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3}, where the composition range of 0≤y≤0.20 was examined for x=0.2 and 0.25. The highest conductivity, 1.85×10{sup −3} S cm{sup −1} at 250 °C, was obtained for (Li{sub 0.25}Sr{sub 0.625}☐{sub 0.125})(Ga{sub 0.25}Ta{sub 0.75})O{sub 3} (x=0.25, y=0.125). Enhanced ionic conductivities were achieved by the introduction of vacancies at the A-sites. - Graphical abstract: Novel lithium-conducting oxides with the cubic perovskite structure (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3} provide a specific solid-solution region with various x and y values, exhibiting the highest ionic conductivity (1.85 S cm{sup −1} at 250 °C) for (Li{sub 0.25}Sr{sub 0.625}☐{sub 0.125})(Ga{sub 0.25}Ta{sub 0.75})O{sub 3} (x=0.25, y=0.125 in (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3}). The vacancies (☐) introduced into the A-sites contribute to the enhancement of lithium diffusion in the perovskite structure because of the enlargement of the bottleneck size and suppression of the interaction between lithium and oxygen. - Highlights: • The perovskite-structured novel Li–Sr–Al/Ga–Ta oxides were investigated. • The Ga cation offers a larger bottleneck by increasing the B−O bond length. • The greater conductivity was observed upon Ga-containing perovskite. • The ionic conductivity was improved by the introduction of vacancies into A-site.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of temperature and frequency on ionic conductivity of Li{sub 3}PO{sub 4}–Pb{sub 3}(PO{sub 4}){sub 2}–BiPO{sub 4} phosphate glasses

Highlights: • Results of ionic conductivities of Li{sub 3}PO{sub 4}–Pb{sub 3}(PO{sub 4}){sub 2}–BiPO{sub 4} phosphate glasses. • Determination of glass transition temperature using DSC method. • Study of temperature and frequency on ionic conductivity of Li{sub 3}PO{sub 4}–Pb{sub 3}(PO{sub 4}){sub 2}–BiPO{sub 4} phosphate glasses. - Abstract: Lithium–Lead–Bismuth phosphates glasses having, a composition 30Li{sub 3}PO{sub 4}–(70 − x)Pb{sub 3}(PO{sub 4}){sub 2}–xBiPO{sub 4} (45 ≤ x ≤ 60 mol%) were prepared by using the melt quenching method 1000 °C. The thermal stability of theses glasses increases with the substitution of Bi{sub 2}O{sub 3} with PbO. The ionic conductivity of all compositions have been measured over a wide temperature (200–500 °C) and frequency range (1–106 Hz). The ionic conductivity data below and above T{sub g} follows Arrhenius and Vogel–Tamman–Fulcher (VTF) relationship, respectively. The activation energies are estimated and discussed. The dependence in frequency of AC conductivity is found to obey Jonscher’s relation.

36 MATERIALS SCIENCE↗

Anisotropic ionic transportation performances of (100) and (112) planes in MAPbI3 single crystal

Highlights: • Anisotropic ion transportations of MAPbI{sub 3} are studied. • Photon excited ion transportation is investigated. • Linear increase trends with incident light power of ion transportation are observed. • Enhanced electron and ion transportations have been observed on (112) plane of MAPbI{sub 3}. • (112) plane of MAPbI{sub 3} shows more active transportation properties than (100). - Abstract: Organic–Inorganic hybrid perovskites attract intensive attentions due to significant optoelectronic performances. However, abnormal phenomena such as photocurrent hysteresis and slow photoconductivity response caused by ion migration made ionic transportation properties to be a hot topic in this area. Thinking of serious influences such as efficiency decay of excited carrier separation and poor reliability are caused by ion migration, systematical research on this topic is still highly demanded. Here, anisotropic ionic transportation performances of (100) and (112) planes in MAPbI{sub 3} single crystal have been investigated with various photon excitation conditions. Enhanced ionic conductance had been extracted on (112) plane both with and without illuminations. Comparing to exponential saturation revealed by the electrons, the ionic conductance exhibits a linear increase trends with incident light power in MAPbI{sub 3}.

36 MATERIALS SCIENCE↗

Effect of aqueous hydrochloric acid and zwitterionic betaine on the mutual solubility between a protic betainium-based ionic liquid and water

The solubility of hydrophobic betainium bis(trifluoromethylsulfonyl)imide ionic liquid in an aqueous phase with controlled acidity has been investigated by a standard liquid–liquid extraction technique. The effect of zwitterionic betaine added into the aqueous phase has also been studied. Quantitative NMR was employed to characterize the distribution behavior of the ionic liquid constituents between the two phases. A mathematical model to describe the ionic liquid solubility in the aqueous phase was developed. Here, this approach was utilized to estimate the conditional solubility product constant of the ionic liquid. The possibility of the transfer of some dissociation products back into the organic phase was investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of hydrophobic ionic liquids aqueous solubility on metal extraction from hydrochloric acid media: Mathematical modelling and trivalent thallium behavior

A mathematical model to explain cations’ solubility of both protic and aprotic ionic liquids in a wide range of hydrochloric acid solutions has been developed. The concept of this model is based on an assumption of the mineral acid extraction into the organic phase, formation of a salt there between an ionic liquid cation and chloride-anion due to ions recombination and partial salt back-extraction. The proposed approach allows estimating corresponding extraction constants. Comparison of calculated and experimentally measured solubility product constants shows that they are in good agreement. It has been determined also that the more the hydrophilicity of the ionic liquids’ cation the more hydrochloric acid is extracted. Furthermore, this model has been utilized to facilitate analysis of thallium transfer into hydrophobic ionic liquids providing insights into the mechanism of metal extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Behavior of astatine and bismuth in non-conventional solvents: Extraction into imidazolium-based ionic liquid and methyl anthranilate with active pharmaceuticals binary mixtures from nitric acid media

Astatine is one of the least chemically studied elements and its behavior in the presence of non- conventional solvents has not been investigated before. This work considers both hydrophobic ionic liquids and binary mixtures as alternatives to conventional solvents. The study is based on the extraction of astatine and bismuth (target material required to produce astatine) into imidazolium-based ionic liquid, and binary mixtures formed by active pharmaceuticals (ibuprofen, lidocaine) and a food grade ingredient (methyl anthranilate). It is shown that both the ionic liquid and binary mixtures can successfully extract At from nitric acid media, but extraction of Bi into the ionic liquid is very inefficient, resulting in a good separation factor for these two elements in the entire studied acidity range. Extraction of At into binary mixtures is very efficient, having distribution ratio values as high as 1000, while the behavior of Bi under these conditions depends on the composition of the mixture. Furthermore, a mathematical model has been developed to fit both At and Bi experimental data and applied to determine corresponding thermodynamic extraction constants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Environmental life cycle assessment methods applied to amine-ionic liquid hybrid CO 2 absorbents

A hybrid solvent mixture of triethyl(octyl)phosphonium cyanopyrrolide [P2228][2-CNPyr] and aqueous monoethanolamine (MEA) has the potential for absorbing CO 2 from post combustion flue gas. However, previous studies have found that the production of phosphonium based ionic liquids (IL) had significantly higher potential environmental impacts compared to MEA. Literature attributes these higher environmental impacts to the phosphine and phosgene-based intermediates required to produce the phosphonium ion of the ionic liquid. This study proposes a novel synthesis pathway that eliminates the need for phosphine and phosgene intermediates in the production of [P2228][2-CNPyr]. The environmental impacts of producing 1kg of the ionic liquid through this novel synthesis route was evaluated using the TRACI 2.1 methodology within the life cycle assessment (LCA) framework. Additionally, the environmental impacts for the production of 1kg of a hybrid solvent was also evaluated and compared against MEA. The life cycle inventory for the production of the IL and its hybrid solvent were calculated based on the stoichiometry and then scaled up. This study found that the IL and its hybrid solvents had higher environmental impacts among 9 of the 10 environmental impact categories calculated by the TRACI 2.1 methodology, except for the ecotoxicity potential. A sensitivity analysis indicated that these solvents were more sensitive to the assumptions of the material requirements of the phosphonium cation than the overall energy or transportation requirements. Despite this sensitivity, both the solvents demonstrated a lower Ecotoxicity Potential compared to MEA, the rest of the environmental impacts were still found to be higher than that of MEA, thereby underscoring the need to investigate novel synthesis routes for the production of phosphonium cation. The uncertainty analysis performed confirmed the findings that the IL has a higher environmental impact potentials across all categories except ecotoxicity potential. The uncertainty analysis also confirms that the phosphonium cation is a major hotspot in production route of these solvents and a source of uncertainty in the model compared to the anion. Altogether, this study underscores the need for investigating novel green chemistry pathway for the synthesis of phosphonium based ionic liquids, such as [P2228][2-CNPyr], to ensure that the these ILs can be a truly green alternative to MEA by not only offering superior CO₂ capture capacity compared to MEA but also being sustainably produced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Pressure Vapor-Liquid Equilibria of 1-Alkyl-1-Methylpyrrolidinium Bis(trifluoromethylsulfonyl)imide Ionic Liquids and CO 2

The high-pressure vapor-liquid equilibrium for the binary systems of carbon dioxide (CO 2 ) and a series of 1-alkyl-1-methyl pyrrolidinium bis(trifluoromethylsulfonyl)amide ionic liquids ([C n C 1 pyr][NTf 2 ] ( n = 3,4,6)) are reported at 298.15, 318.15 and 338.15 K and at pressures up to 20 MPa. Experiments were conducted using gravimetric (IGA and XEMIS microbalances) and a volumetric method (high-pressure view cell). The solubility of CO 2 in pyrrolidinium ionic liquids increases with decreasing temperature and increasing pressure. The CO 2 solubility also slightly increases with increase in alkyl chain length on the pyrrolidinium cation. Molar volume and volume expansion of CO 2 + IL mixtures are also reported. The Fickian diffusion of CO 2 in pyrrolidinium based ionic liquids (~10 -10 m 2 ·s -1 ) was calculated at pressures of up to 2 MPa and found to be at the same order of magnitude but slightly lower than the diffusivity of CO 2 in imidazolium based ionic liquid with the [NTf 2 ] anion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Viscosity of 1-Alkyl-1-methylpyrrolidinium Bis(trifluoromethylsulfonyl)imide Ionic Liquids Saturated with Compressed CO 2

The viscosity of mixtures of pyrrolidinium-based ionic liquids saturated with compressed CO 2 was measured using a high-pressure viscometer at three different temperatures (298.15, 318.15 and 338.15 K). The high-pressure viscosity of 1-propyl-1-methyl-pyrrolidinium ([C 3 C 1 pyr]), 1-butyl-1-methyl-pyrrolidinium ([C 4 C 1 pyr]), and 1-hexyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)amide ([C 6 C 1 pyr]) cations with common anion, bis(trifluoromethylsulfonyl)amide ([NTf 2 ]), was measured up to a maximum CO 2 pressure of 25 MPa. In the temperature range investigated, the viscosity of the ionic liquid/ CO 2 mixture dramatically decreases with increasing of CO 2 pressure up to approximately 7 MPa but the viscosity decrease becomes less significant at higher CO 2 pressures (from 7 to 25 MPa) because the CO 2 composition in ILs slightly increases with pressure. At lower CO 2 pressures (compositions), temperature has a higher impact on the CO 2 solubility in IL, thus the viscosity drops significantly for lower temperatures (e.g. 298.15 K). The effect of alkyl chain length of the cation on the viscosity of ionic liquid/ CO 2 mixture was also measured. Though the pure [C n C 1 pyr][NTf 2 ] viscosity increases significantly with the increasing alkyl chain length of the cation, the viscosity of every ionic liquid/ CO 2 mixture tested herein become quite similar at higher CO 2 pressures, for a fixed temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solid-State Ionic Rectification in Perovskite Nanowire Heterostructures

Halide perovskites have attracted increasing research attention with regard to their potential for optoelectronic applications. Because of its low activation energy, ion migration is implicated in the long-term stability and many unusual transport behaviors of halide perovskite devices. However, direct observation and precise control of the ionic transport in halide perovskite crystals remain challenging. Here, we have designed an axial CsPbBr 3 -CsPbCl 3 nanowire heterostructure, in which electric-field-induced halide ion migration was clearly visualized and quantified. We demonstrated that halide ion migration is dependent on the applied electric field and exhibits ionic rectification in this solid-state system, which is due to the nonuniform distribution of the ionic vacancies in the nanowire that results from a competition between electrical screening and their creation/destruction at the electrodes' interfaces. Furthermore, the asymmetric heterostructure characteristics add an additional knob to control the ion movement in the design of advanced ionic circuits with halide perovskites as building blocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vertically Aligned and Continuous Nanoscale Ceramic–Polymer Interfaces in Composite Solid Polymer Electrolytes for Enhanced Ionic Conductivity

Among all solid electrolytes, composite solid polymer electrolytes, comprised of polymer matrix and ceramic fillers, garner great interest due to the enhancement of ionic conductivity and mechanical properties derived from ceramic–polymer interactions. Here, we report a composite electrolyte with densely packed, vertically aligned, and continuous nanoscale ceramic–polymer interfaces, using surface-modified anodized aluminum oxide as the ceramic scaffold and poly(ethylene oxide) as the polymer matrix. The fast Li + transport along the ceramic–polymer interfaces was proven experimentally for the first time, and an interfacial ionic conductivity higher than 10 –3 S/cm at 0 °C was predicted. The presented composite solid electrolyte achieved an ionic conductivity as high as 5.82 × 10 –4 S/cm at the electrode level. In conclusion, the vertically aligned interfacial structure in the composite electrolytes enables the viable application of the composite solid electrolyte with superior ionic conductivity and high hardness, allowing Li–Li cells to be cycled at a small polarization without Li dendrite penetration.

36 MATERIALS SCIENCE↗

Facile Strategy to Prepare Poly(ionic liquid)-Coated Solid Polymer Electrolytes through Layer-by-Layer Assembly

The inability of solid polymer electrolytes to preserve strong mechanical strength with high ionic conductivity hinders the commercialization of lithium metal batteries (LMBs). The success of fabricating layer-by-layer (LbL)-assembled electrolytes has realized the application of flexible solid polymer electrolytes in electrochemical devices. Here, we demonstrate a rational strategy to construct solid electrolytes coated with multiple ultrathin layers of polyanions (poly(sodium 4-styrenesulfonate)) and polycations (linear poly(1-butyl-3-(4-vinylbenzyl)-1H-imidazolium chloride) (BVIC)/linear poly(PEG 4 -VIC)/SiO 2 -g-poly(PEG 4 -VIC)) using an LbL assembly method. Poly(ionic liquid) backbones and PEG side groups are employed to facilitate the transport of lithium ions via the segmental motion of the macromolecular matrix. The fabricated free-standing membranes exhibited good ionic conductivities of 9.03–10 × 10 –4 S cm –1 . Furthermore, a Li/LiFePO 4 cell assembled with the LbL-membrane electrolytes exhibits an initial high discharge capacity of 143–158 mAhg –1 at 60 °C with high columbic efficiency. In conclusion, this approach, which combines polymer synthesis and LbL self-assembly, is an effective and facile route to fabricate solid polymer electrolyte membranes with superior ionic conductivity and mechanical robustness, which are useful for electrochemical devices and high-voltage battery applications.

25 ENERGY STORAGE↗

Role of Electrical Double Layer Structure in Ionic Liquid Gated Devices

Ionic liquid gating of transition metal oxides has enabled new states (magnetic, electronic, metal–insulator), providing fundamental insights into the physics of strongly correlated oxides. However, despite much research activity, little is known about the correlation of the structure of the liquids in contact with the transition metal oxide surface, its evolution with the applied electric potential, and its correlation with the measured electronic properties of the oxide. Here, we investigate the structure of an ionic liquid at a semiconducting oxide interface during the operation of a thin film transistor where the electrical double layer gates the device using experiment and theory. We show that the transition between the ON and OFF states of the amorphous indium gallium zinc oxide transistor is accompanied by a densification and preferential spatial orientation of counterions at the oxide channel surface. This process occurs in three distinct steps, corresponding to ion orientations, and consequently, regimes of different electrical conductivity. The reason for this can be found in the surface charge densities on the oxide surface when different ion arrangements are present. Overall, the field-effect gating process is elucidated in terms of the interfacial ionic liquid structure, and this provides unprecedented insight into the working of a liquid gated transistor linking the nanoscopic structure to the functional properties. This knowledge will enable both new ionic liquid design as well as advanced device concepts.

36 MATERIALS SCIENCE↗

Ion Migration Studies in Exfoliated 2D Molybdenum Oxide via Ionic Liquid Gating for Neuromorphic Device Applications

The formation of an electric double layer in ionic liquid (IL) can electrostatically induce charge carriers and/or intercalate ions in and out of the lattice which can trigger a large change of the electronic, optical, and magnetic properties of materials and even modify the crystal structure. Here, we present a systematic study of ionic liquid gating of exfoliated 2D molybdenum trioxide (MoO 3 ) devices and correlate the resultant electrical properties to the electrochemical doping via ion migration during the IL biasing process. A nearly 9 orders of magnitude modulation of the MoO 3 conductivity is obtained for the two types of ionic liquids that are investigated. In addition, notably rapid on/off switching was realized through a lithium-containing ionic liquid whereas much slower modulation was induced via oxygen extraction/intercalation. Time of flight–secondary ion mass spectrometry confirms the Li intercalation. Density functional theory (DFT) calculations have been carried out to examine the underlying metallization mechanism. Results of short-pulse tests show the potential of these MoO 3 devices as neuromorphic computing elements due to their synaptic plasticity.

2D materials↗

Separation of carbon dioxide and sulfur dioxide gases using room-temperature ionic liquid (hmim)(Tf2N)

To understand capturing and/or enhanced gaseous selectivity of industrial flue gases containing CO{sub 2} and SO{sub 2} using room-temperature ionic liquids, we have developed a ternary equation of state (EOS) model for a CO{sub 2}/SO{sub 2}/1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ((hmim)(Tf2N)) system. The present model is based on a generic RK (Redlich-Kwong) EOS, with empirical binary interaction parameters of each binary system. These interaction parameters have been determined using our measured VLE (vapor-liquid-equilibrium) data for SO{sub 2}/(hmim)(Tf2N) and CO{sub 2}/(hmim)(Tf2N) and literature data for CO{sub 2}/SO{sub 2}. The validity of the present EOS has been checked by conducting ternary VLE experiments for the present system. With this EOS, isothermal ternary phase diagrams and solubility (VLE) behaviors have been calculated for various (T, P, and feed compositions) conditions. For large and equimolar CO{sub 2}/SO{sub 2} mole ratios, the gaseous selectivity is nearly independent of the amount of the ionic liquid addition. However, for small CO{sub 2}/SO{sub 2} mole ratios the addition of the ionic liquid significantly increases the selectivity. The strong absorption of CO{sub 2} and SO{sub 2} in this ionic liquid may be practical for the simultaneous capture of these acid gases. 39 refs., 8 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Ionic Liquids and Ionizing Radiation: Reactivity of Highly Energetic Species

Due to their unique properties, ionic liquids present many opportunities for basic research on the interactions of radiation with materials under conditions not previously available. At the same time, there are practical applied reasons for characterizing, understanding, and being able to predict how ionic-liquid-based devices and industrial-scale systems will perform under conditions of extreme reactivity, including radiation. This perspective discusses current issues in ionic liquid physical chemistry, provides a brief introduction to radiation chemistry, draws attention to some key findings in ionic liquid radiation chemistry, and identifies some current hot topics and new opportunities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ion beam irradiation as a tool to improve the ionic conductivity in solid polymer electrolyte systems

Solid polymer electrolytes (SPEs) have potential applications in solid state electronic and energy devices. The optimum conductivity of SPEs required for such applications is about 10{sup −1} – 10{sup −3} Scm{sup −1}, which is hard to achieve in these systems. It is observed that ionic conductivity of SPEs continuously increase with increasing concentration of inorganic salt in the host polymer. However, there is a critical concentration of the salt beyond which the conductivity of SPEs decreases due to the formation of ion pairs. In the present study, solid polymer thin films based on poly (ethylene oxide) (PEO) complexed with NaBr salt with different concentrations have been prepared and the concentration at which ion pair formation occurs in PEO{sub x}NaBr is identified. The microstructure of the SPE with highest ionic conductivity is modified by irradiating it with low energy O{sup +1} ion (100 keV) of different fluencies. It is observed that the ionic conductivity of irradiated SPEs increases by one order in magnitude. The increase in ionic conductivity may be attributed to the enhanced segmental motion of the polymer chains due to radiation induced micro structural modification.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗