SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Irradiation induced non-equilibrium point defect populations influence mass transport in oxides, which in turn affects their stability and performance in hostile environments. In this study a strong dose rate dependence is observed.
It is widely accepted that micro- and nanoscale inhomogeneities govern the performance of many thin-film solar cell absorbers. These inhomogeneities yield material properties (e.g., composition, structure, and charge collection) that are challenging to correlate across length scales and measurement modalities. The challenge is compounded if a correlation is sought during device operation or in conditions that mimic aging under particular stressors (e.g., heat and electrical bias). Correlative approaches, particularly those based on synchrotron x-ray sources, are powerful since they can access several material properties in different modes (e.g., fluorescence, diffraction, and absorption) with minimal sample preparation. Small-scale laboratory x-ray instruments have begun to offer multi-modality but are typically limited by low x-ray photon flux, low spatial resolution, or specific sample sizes. To overcome these limitations, a characterization stage was developed to enable multi-scale, multi-modal operando measurements of industrially relevant photovoltaic devices. The stage offers compatibility across synchrotron x-ray facilities, enabling correlation between nanoscale x-ray fluorescence microscopy, microscale x-ray diffraction microscopy, and x-ray beam induced current microscopy, among others. Furthermore, the stage can accommodate device sizes up to 25 × 25 mm 2 , offering access to multiple regions of interest and increasing the statistical significance of correlated properties. The stage materials can sustain humid and non-oxidizing atmospheres, and temperature ranges encountered by photovoltaic devices in operational environments (e.g., from 25 to 100 °C). As a case study, we discuss the functionality of the stage by studying Se-alloyed CdTe photovoltaic devices aged in the stage between 25 and 100 °C.
Carbon fiber epoxy composites are increasingly used in systems requiring a material that is both strong and light weight, as in airplanes, cars, and pressure vessels. In fire environments, carbon fiber epoxy composites are a fuel source subject to oxidation. This literature review seeks to provide material properties as well as uncertainty bounds for those properties for computational models of decomposing carbon fiber epoxy composites. The goal is to guide analysts when measurements are lacking and increase credibility of uncertainty quantification ranges.
Artificial intelligence (AI) holds immense promise for revolutionizing microscopy, yet its widespread adoption has been hindered by challenges ranging from user inexperience to limited model transferability and difficulties in operationalizing machine learning. This presentation showcases our approach to developing practical autonomy for materials discovery, aiming to accelerate the integration of AI into everyday microscopy workflows. As shown in Fig. 1, I will focus on three key areas: understanding order-disorder transitions, quantifying point defects, and achieving truly device-scale microscopy. First, I will demonstrate the power of multi-modal knowledge graphs for integrating diverse microscopy data. By combining imaging, spectroscopy, and diffraction data, these graphs provide a holistic view of material behavior, capturing the intricate relationships between different modalities [1,2]. I will present a case study on how these models illuminate the structural and chemical changes associated with irradiation in oxide thin films, revealing critical insights for designing materials for extreme environments like spaceflight and nuclear energy. Specifically, I will show how multi-modal analysis clarifies the evolution of order-disorder transitions under irradiation, a key factor influencing material performance in these applications. Next, I will address the challenge of quantifying point defects in 2D materials. We demonstrate the application of computer vision and transfer learning to accurately identify and classify various defect types, such as vacancies and substitutional atoms, and to quantify their concentrations. This information is crucial for understanding and tailoring the properties of 2D materials for applications in electronics, optoelectronics, and catalysis. For example, I will show how our models can characterize the topological distribution of point defects in MXene transition metal carbides, providing valuable insights for optimizing their performance in energy storage and separation science. Finally, I will discuss our progress toward autonomous device-scale microscopy [3,4]. We are fundamentally redesigning electron microscopes around the principles of machine reasoning, enabling automation beyond basic tasks like sample navigation and data acquisition to include sophisticated experimental design. This approach paves the way for truly reproducible and massively scaled analysis campaigns. I will emphasize the importance of autonomous microscopy platforms for high-throughput materials discovery and characterization, facilitating the rapid screening of materials for a broad range of applications and accelerating the development of next-generation technologies.
Current generation light water reactors (LWRs), sodium cooled fast reactors (SFRs), small modular reactors (SMRs), and next generation nuclear plants (NGNPs) produce harsh environments in and near the reactor core that can severely tax material performance and limit component operational life. To address this issue, several Department of Energy Office of Nuclear Energy (DOE-NE) research programs are evaluating the long duration irradiation performance of fuel and structural materials used in existing and new reactors. In order to maximize the amount of information obtained from Material Testing Reactor (MTR) irradiations, DOE is also funding development of enhanced instrumentation that will be able to obtain in-situ, real-time data on key material characteristics and properties, with unprecedented accuracy and resolution. Such data are required to validate new multi-scale, multi-physics modeling tools under development as part of a science-based, engineering driven approach to reactor development. It is not feasible to obtain high resolution/microscale data with the current state of instrumentation technology. However, ultrasound-based sensors offer the ability to obtain such data if it is demonstrated that these sensors and their associated transducers are resistant to high neutron flux, high gamma radiation, and high temperature. To address this need, the Advanced Test Reactor National Scientific User Facility (ATR-NSUF) is funding an irradiation, led by PSU, at the Massachusetts Institute of Technology Research Reactor to test the survivability of ultrasound transducers. As part of this effort, PSU and collaborators have designed, fabricated, and provided piezoelectric and magnetostrictive transducers that are optimized to perform in harsh, high flux, environments. Four piezoelectric transducers were fabricated with either aluminum nitride, zinc oxide, or bismuth titanate as the active element that were coupled to either Kovar or aluminum waveguides and two magnetostrictive transducers were fabricated with Remendur or Galfenol as the active elements. Pulse-echo ultrasonic measurements of these transducers are made in-situ. This paper will present an overview of the test design including selection criteria for candidate materials and optimization of test assembly parameters, data obtained from both out-of-pile and in-pile testing at elevated temperatures, and an assessment based on initial data of the expected performance of ultrasonic devices in irradiation conditions
This study investigates the effectiveness of Cu as a corrosion barrier in supercritical carbon dioxide (s-CO 2 ) by coating 316 stainless steel (316) with various thicknesses of Cu. In this work, 316 exposed to s-CO 2 with 50 ppm CO showed a reduction in oxidation corresponding to the thickness of its Cu barrier coating. Additionally, a continuous Cu layer between the environment and the alloy was found to correlate to an elimination of carburization and corrosion-related mechanical degradation. This Cu coating technique could be applied over a variety of temperatures to improve the corrosion resistance of alloys that are susceptible to carburization.
Developing efficient and low-cost urea oxidation reaction (UOR) catalysts is a promising but still challenging task for environment and energy conversion technologies such as wastewater remediation and urea electrolysis. In this work, NiO nanoparticles that incorporated graphene as the NiO@Graphene composite were constructed to study the UOR process in terms of density functional theory. The single-atom model, which differed from the previous heterojunction model, was employed for the adsorption/desorption of urea and CO 2 in the alkaline media. As demonstrated from the calculated results, NiO@Graphene prefers to adsorb the hydroxyl group than urea in the initial stage due to the stronger adsorption energy of the hydroxyl group. After NiOOH@Graphene was formed in the alkaline electrolyte, it presents excellent desorption energy of CO 2 in the rate-determining step. Electronic density difference and the d band center diagram further confirmed that the Ni(III) species is the most favorable site for urea oxidation while facilitating charge transfer between urea and NiO@Graphene. Moreover, graphene provides a large surface for the incorporation of NiO nanoparticles, enhancing the electron transfer between NiOOH and graphene and promoting the mass transport in the alkaline electrolyte. Notably, this work provides theoretical guidance for the electrochemical urea oxidation work.
Abstract Atomic precision advanced manufacturing (APAM) leverages the highly reactive nature of Si dangling bonds relative to H- or Cl-passivated Si to selectively adsorb precursor molecules into lithographically defined areas with sub-nanometer resolution. Due to the high reactivity of dangling bonds, this process is confined to ultra-high vacuum (UHV) environments, which currently limits its commercialization and broad-based appeal. In this work, we explore the use of halogen adatoms to preserve APAM-derived lithographic patterns outside of UHV to enable facile transfer into real-world commercial processes. Specifically, we examine the stability of H-, Cl-, Br-, and I-passivated Si(100) in inert N 2 and ambient environments. Characterization with scanning tunneling microscopy and x-ray photoelectron spectroscopy (XPS) confirmed that each of the fully passivated surfaces were resistant to oxidation in 1 atm of N 2 for up to 44 h. Varying levels of surface degradation and contamination were observed upon exposure to the laboratory ambient environment. Characterization by ex situ XPS after ambient exposures ranging from 15 min to 8 h indicated the Br– and I–passivated Si surfaces were highly resistant to degradation, while Cl–passivated Si showed signs of oxidation within minutes of ambient exposure. As a proof-of-principle demonstration of pattern preservation, a H–passivated Si sample patterned and passivated with independent Cl, Br, I, and bare Si regions was shown to maintain its integrity in all but the bare Si region post-exposure to an N 2 environment. The successful demonstration of the preservation of APAM patterns outside of UHV environments opens new possibilities for transporting atomically-precise devices outside of UHV for integrating with non-UHV processes, such as other chemistries and commercial semiconductor device processes.
Probing and understanding the local chemical environment of an active site is essential for designing high-performance single-atom catalysts (SACs). Density functional theory (DFT) calculations were performed to investigate the ligand configuration and site geometry of MgAl 2 O 4 -supported iridium single atoms (Ir-1) toward catalytic carbon monoxide (CO) oxidation. We employed MgAl 2 O 4 (111) and MgAl 2 O 4 (211) as the model substrates with adsorbed Ir single atoms of different site geometries. DFT calculations revealed that the Mg-site on MgAl 2 O 4 (111) and the step site on MgAl 2 O 4 (211) are the most stable adsorption sites for Ir single atoms. Irrespective of site choices, CO oxidation on supported Ir single atoms follows the Eley-Rideal (E-R) mechanism, in which the surface oxygen vacancies close to the Ir single atoms activate molecular O 2 with a negligible barrier and the rate-limiting step is the gas-phase CO directly attacking the O-Ir species that is modulated by a CO ligand. Furthermore, first-principles X-ray absorption near-edge spectra of reaction intermediates along with in situ/operando X-ray absorption spectroscopy (XAS) suggest that Ir single atoms adsorb primarily on the step sites of MgAl 2 O 4 . However, microkinetic modeling predicts that a higher activity can be attained on the equally stable Mg-site, maximizing the population of which in catalyst synthesis might prove fruitful in future studies. Electronic structure analysis indicates that the CO ligand increases the reactivity of adsorbed oxygen atoms bound to Ir single atoms by increasing the antibonding nature of the O-Ir bond.
Understanding how protective coatings respond to the harsh low-Earth orbit (LEO) environment is essential for ensuring the safety, longevity, and cost-effectiveness of spacecraft. In particular, identifying environmentally friendly, non-chromate alternatives that can maintain performance under such conditions has both technological and regulatory significance. This study investigates the environmental stability of zirconium-based hybrid conversion coatings with Cu additives (Cu10 and Cu20) applied to cold-rolled steel, tested in the Materials International Space Station Experiment (MISSE) outside the International Space Station (ISS). Chemical and morphological analyses were carried out using a combination of electron microscopy and X-ray spectroscopy techniques, including scanning electron microscopy (SEM), scanning transmission electron microscopy with energy-dispersive X-ray spectroscopy (STEM-EDS), X-ray photoelectron spectroscopy (XPS), and X-ray absorption near-edge structure (XANES) spectroscopy. After exposure outside the ISS, all coatings remained structurally intact, with all exhibiting a uniform Zr-rich matrix and embedded Cu-rich clusters, while a thin Si-rich surface layer developed from interaction with space environments. Depth-resolved XPS showed a layered structure with CuO on the surface, Cu 2 O, and partial Zr(IV) reduction near Cu-rich sites, evidence of Atomic Oxygen (AO)-driven surface oxidation. These results demonstrate that Cu–Zr coatings maintain their chemical integrity and microstructure in harsh space environments, offering a non-chromate alternative for long-term aerospace protection. These insights provide valuable guidance for developing next-generation protective coatings that combine environmental sustainability with the reliability required for future aerospace and orbital applications.
Structural materials such as Ni-based superalloys used in high-temperature power cycles are routinely exposed to toxic environments including high temperature and pressure, aqueous and gas corrosion, etc. Here, we present a physics-informed machine learning approach to predict the oxidation response of diverse Ni-superalloys. First, a high-fidelity experimental dataset is curated from typical oxidation mass-change experiments in air, covering 25+ elements and different physical behavior such as parabolic growth, non-parabolic growth, and oxide spallation. Second, the dataset is featurized using thermophysical, chemical, and mechanical properties obtained from high-throughput CALPHAD calculations. Third, several machine learning models are developed to identify key features related to mass-change characteristics and model the mass-change curve for various alloys. Finally, the model is deployed to rapidly screen over a new composition space and down-select candidate alloys with high oxidation resistance for experimental validation.
The ability to controllably chlorinate metal-oxide surfaces can provide opportunities for designing selective oxidation catalysts. In the present study, we investigated the surface chlorination of IrO2(110) by HCl using temperature programmed reaction spectroscopy (TPRS), x-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. We find that exposing IrO2(110) to HCl, followed by heating to 650 K in ultrahigh vacuum, produces nearly equal quantities of on-top and bridging Cl atoms on the surface, Clt and Clbr, where the Clbr atoms replace O-atoms that are removed from the surface by H2O formation. After HCl adsorption at 85 K, only H2O desorbs at low Cl coverages during TPRS, but HCl begins to desorb in increasing yields as the Cl coverage is increased above about 0.5 monolayer (ML). The desorption of Cl2 was not observed under any conditions, in good agreement with the high barrier for this reaction predicted by DFT. A maximum Cl coverage of 1 ML, with nearly equal coverages of Clt and Clbr atoms, could be generated by reacting HCl with IrO2(110) in UHV. Our results suggest that a kinetic competition between recombinative HCl and H2O desorption under the conditions studied limits the saturation Cl coverage to a value less than the 2 ML maximum predicted by thermodynamics. XPS further shows that the partitioning of Cl between the Clt and Clbr states can be altered by subjecting partially chlorinated IrO2(110) to reductive or oxidative treatments, demonstrating that the Cl site population can change dynamically in response to the gas environment. Our results provide insights for understanding the chlorination of IrO2(110) by HCl and can enable future experimental studies to determine how Cl-modification alters the surface chemical reactivity of IrO2(110) and potentially enhances selectivity toward partial oxidation chemistry.
Presentation slides for 2025 MRS Fall Meeting & Exhibit. Reliable oxygen sensors are vital for high temperature applications including combustion engines, steel production, and petrochemical refining, yet identifying stable, high-performance materials for such environments remain challenge. We apply machine learning (ML) to predict the atmospheric oxygen partial pressure–dependent conductivity of perovskite oxides, combining data from the Materials Project and published datasets.
ABSTRACT Leptothrix ochracea creates distinctive iron-mineralized mats that carpet streams and wetlands. Easily recognized by its iron-mineralized sheaths, L. ochracea was one of the first microorganisms described in the 1800s. Yet it has never been isolated and does not have a complete genome sequence available, so key questions about its physiology remain unresolved. It is debated whether iron oxidation can be used for energy or growth and if L. ochracea is an autotroph, heterotroph, or mixotroph. To address these issues, we sampled L. ochracea -rich mats from three of its typical environments (a stream, wetlands, and a drainage channel) and reconstructed nine high-quality genomes of L. ochracea from metagenomes. These genomes contain iron oxidase genes cyc2 and mtoA, showing that L. ochracea has the potential to conserve energy from iron oxidation. Sox genes confer potential to oxidize sulfur for energy. There are genes for both carbon fixation (RuBisCO) and utilization of sugars and organic acids (acetate, lactate, and formate). In silico stoichiometric metabolic models further demonstrated the potential for growth using sugars and organic acids. Metatranscriptomes showed a high expression of genes for iron oxidation; aerobic respiration; and utilization of lactate, acetate, and sugars, as well as RuBisCO, supporting mixotrophic growth in the environment. In summary, our results suggest that L. ochracea has substantial metabolic flexibility. It is adapted to iron-rich, organic carbon-containing wetland niches, where it can thrive as a mixotrophic iron oxidizer by utilizing both iron oxidation and organics for energy generation and both inorganic and organic carbon for cell and sheath production. IMPORTANCE Winogradsky's observations of L. ochracea led him to propose autotrophic iron oxidation as a new microbial metabolism, following his work on autotrophic sulfur-oxidizers. While much culture-based research has ensued, isolation proved elusive, so most work on L. ochracea has been based in the environment and in microcosms. Meanwhile, the autotrophic Gallionella became the model for freshwater microbial iron oxidation, while heterotrophic and mixotrophic iron oxidation is not well-studied. Ecological studies have shown that Leptothrix overtakes Gallionella when dissolved organic carbon content increases, demonstrating distinct niches. This study presents the first near-complete genomes of L. ochracea , which share some features with autotrophic iron oxidizers, while also incorporating heterotrophic metabolisms. These genome, metabolic modeling, and transcriptome results give us a detailed metabolic picture of how the organism may combine lithoautotrophy with organoheterotrophy to promote Fe oxidation and C cycling and drive many biogeochemical processes resulting from microbial growth and iron oxyhydroxide formation in wetlands.
The dynamical nature of single-site catalysts under non-equilibrium conditions poses significant challenges in the full characterization of their active sites. The “29” oxide is a thin Cu x O film grown on Cu(111) which provides a well-defined surface on which to study the structure and chemistry of atomically dispersed precious metals. A combination of experimental and first-principles approaches is used to investigate the factors that influence the mobility of metal adatoms and their clustering tendencies. Our work elucidates how a homogenous coordination environment of neutral single-atoms can be obtained when its tendency to break oxide bonds within its vicinity is low. Herein we demonstrate that this in turn affects the chemical atomically dispersed species on thin-film oxides, as defects on the oxide would in fact allow such species to be more accessible to CO. We thus highlight the importance of understanding the relationship between defects and atomically dispersed active sites upon designing single-site catalysts.
The supercritical carbon dioxide (sCO2) Allam-Fetvedt cycle employs high-temperature oxy-combustion using sCO2 as the working fluid, leading to a unique and challenging environment for materials. In this cycle, pressurized gaseous fuel is combusted in the presence of a hot oxidant flow containing a mixture of CO2 and oxygen and a hot CO2 diluent recycle stream at approximately 300 bar under lean combustion conditions. We present high-fidelity reacting simulations of this oxy-combustor environment and compare the results when performing simulations with ideal and non-ideal equations of state. By doing so, we identify if the combustor behavior at the regime of interest is sensitive enough to the equation of state to justify the added computational cost incurred with a non-ideal equation of state.
Lighting application efficiency (LAE) describes the efficient delivery of light from the light source to the lighted task and is viewed as a new frontier—increasing energy savings with solid-state lighting (SSL) technologies. The framework for LAE that is proposed by the U.S. Department of Energy (DOE) consists of four major elements: light source efficiency, optical delivery efficiency, spectral efficiency, and intensity effectiveness. This report focuses on a sampling of the available SSL products that can be broadly defined as having modified spectral output because the method of spectra modification has a significant impact on light source efficiency and long-term optical delivery and spectral efficiencies. This report focused on the changes in light source, optical delivery, and spectral efficiencies that occur during aging of SSL devices. An accelerated stress test (AST) regiment was developed for the devices under test (DUTs) examined in this report to provide insights into how the performance of SSL devices change with aging. The AST protocols demonstrate that the SSL products discussed in this report often reduce light source efficiency to achieve different spectral characteristics. In addition, aging of the optical components (e.g., lenses, solder masks) in SSL devices can produce increased light absorption, which negatively impacts optical delivery efficiency and light source efficiency. The modified spectral outputs of the selected SSL products discussed in this report come in a variety of form factors and achieve enhanced optical performance by using a variety of methods. All of the products examined in this study use mid-power light-emitting diodes (MP-LEDs), although the number, configuration, phosphor content, and light-emitting diode (LED) pump of the MP-LEDs differ. Product MS-1 is a 60-watt (W) replacement A19 lamp with a hermetically sealed glass globe, which contains an embedded optical filter to absorb green and yellow emissions, thereby creating a “sunlike” modified spectrum. Product MS-2 is a 60-W replacement A19 lamp with 30 MP-LEDs, and it uses a violet LED pump, along with green and red phosphor emissions, to produce a “healthy” spectrum. This spectrum omits blue emissions in an effort to reduce melanopic lux. Product MS-3 is an LED module consisting of 21 MP-LEDs that use a violet LED pump, along with blue, green, and red phosphors, to produce a “sunlike” spectrum. Products MS-4 and MS-5 are both 6-inch (in) downlights that use a manual switching mechanism so that users can select application-specific correlated color temperatures before installation. Products MS-4 and MS-5 both contain two LED primaries (2,700 Kelvin [K] and 5,000 K) for spectral tuning. Product MS-4 contains 12 MP-LEDs for each LED primary, and Product MS-5 contains 10 MP-LEDs for each LED primary. This report summarizes the overall findings from up to 8,000 hours (hrs) of AST on the lamp DUTs (Products MS-1 and MS-2); up to 5,000 hrs of AST on the LED light engine DUTs (Product MS-3); and up to 7,000 hrs of AST on the downlight DUTs (Products MS-4 and MS-5). The AST procedures used in this study included a room temperature operational life (RTOL) test, an operational life test conducted at 45 degrees Celsius (°C; 45OL) test, an operational life test conducted at 75°C (75OL), a wet high-temperature operational life test performed at 65°C and 90% relative humidity (6590), and a wet high-temperature operational life test performed at 75°C and 75% relative humidity (7575). The AST procedures used for Products MS-1 and MS-2 were RTOL, 45OL, and 6590. The AST procedures used for Products MS-3, MS-4, and MS-5 were RTOL, 75OL, and 7575. During the ASTs described herein, separate populations of each product (three DUTs in each population for Products MS-1, MS-2, MS-4, and MS-5; four DUTs in each population for Product MS-3) were subjected to power cycling of 1 hr on and 1 hr off. The key findings from this study include the following. Enhanced optical performance came at the cost of reduced light source efficiency for the lamps and light engines examined in this study. The optical filter used to produce a “sunlike” spectrum for Product MS-1 reduced light source efficiency by 26%, from 113 lumens per watt (lm/W) to 85 lm/W. Products MS-2 and MS-3 that used a violet-pumped LED to achieve “healthy” and “sunlike” enhanced optical performance, respectively, suffered the largest reduction in initial light source efficiency (49 lm/W for Product MS-2 and 68 lm/W for Products MS-3) perhaps because of the use of violet LED as the optical pump. Product MS-2 also had the poorest color fidelity because of undersaturation of blues and oversaturation of greens and yellows. Chromaticity maintenance of the products in this study was generally good, with parametric failure only occurring for one product at one AST condition (i.e., Product MS-3 at 7575). The chromaticity shift for Product MS-3 in 7575 test conditions resulted from reduced emissions of the broad green and red phosphors used to mimic sunlight in the 500–750 nanometer (nm) range. As a result of these phosphor emission losses, chromaticity shifted toward the more stable violet-pumped LED and blue phosphor. Although chromaticity maintenance was acceptable for most products tested, different chromaticity shift mechanisms were observed for temperature and humidity tests compared with temperature alone for Products MS-1, MS-2, and MS-3. For Product MS-1, a relative increase in green emissions was observed with humidity, which may indicate humidity-accelerated degradation of the optical filter at green wavelengths (optical delivery efficiency reduction) or degradation of the emitters in the red region (spectral efficiency reduction). The violet-pumped products (i.e., MS-2 and MS-3) exhibited different chromaticity shift behavior in the temperature-humidity environments, with Product MS-2 shifting generally yellow because of photo-induced oxidation of the plastic globe (i.e., a reduction of optical delivery efficiency) and Product MS-3 shifting toward violet and blue emitters because of faster loss of emission from green and red phosphors (i.e., a reduction in spectral efficiency). Because of an initial drop in power consumption, the light source efficiency of downlights (Products MS-4 and MS-5) increased at RTOL throughout the test duration. The light source efficiency initially increased during 75OL until a decay in luminous flux maintenance (LFM) dominated light source efficiency, whereas the light source efficiency decreased for the entire 7575 test duration. It was found that increasing the ambient environment of an SSL device from 25°C to 75°C decreases the LFM by 2.7 to 5.5, depending on design of the SSL device. Adding humidity to the system (75OL to 7575) was found to decrease LFM by another factor of approximately 3.0. A common location of failure was identified for the downlights (Products MS-4 and MS-5) operated in the 7575 environment. This failure abruptly occurred between 3,000 to 5,000 hrs of testing on the film capacitor of the electromagnetic interference (EMI) filter near the diode bridge for 11 of the 12 downlights. It is likely that this failure was caused by a combination of the high electrical voltage across the capacitor, the location of the capacitor near the heat sources (e.g., transformers, diode bridges, power resistors), and the high stress environment of 7575. Longer test times are needed to fully understand the LFM, luminous efficacy changes, and chromaticity shifts for some of the products. Because of the high reliability, light source efficiency, and spectral tuning capabilities of LEDs, the expectations of LAE for SSL products are greatly increased over traditional lighting products. The data gathered in this report begin to provide an understanding of the tradeoffs that current SSL products undergo when optimizing the different efficiency elements of LAE. As discussed in this report, the findings from the tests conducted show that the optimization of spectral efficiency can come at the cost of initial light source efficiency. Furthermore, the introduction of violet LEDs can promote long-term optical delivery efficiency degradation, and the introduction of optical filters or new phosphors can lead to unwanted spectral efficiency changes because the ratio of phosphor emitters changes with aging. The data presented in this report also identified a common failure location in 6-in downlights. The results regarding long-term behavior of the modified spectra devices studied provide valuable information about changes to the light source, spectral, and optical delivery efficiencies as the devices age. This information can be used to improve future SSL designs.
Nanoparticles decorated electrodes (NDEs) are useful in fuel cells, electrolyzers, water treatment, and chemical synthesis. Here, in this study, we show that by rapidly bringing a mixed ionic-electronic conductor outside its electrochemical stability window, one can achieve uniform dispersion of metallic nanoparticles inside its bulk and at the surface and improve its electrocatalytic performance when back under normal functional conditions. Surprisingly, this can happen under anodic as well as cathodic current/voltage shocks in an ABO 3 perovskite oxide, La 0.4 Ca 0.4 Ti 0.88 Fe 0.06 Ni 0.06 O 3-δ (LCTFN), across a wide range of H 2 /O 2 gas environments at 800 °C. One possible mechanism for bulk Fe 0 /Ni 0 precipitation under anodic shock condition is the incomplete oxygen oxidation (O 2 – → O α– , 0 < α < 2), migration and escape of oxygen to interfaces, and “whiplash” transition-metal reduction due to low electronic conductivity. We show that both cathodic and anodic shocks can produce NDEs to enhance electrocatalytic performance, potentially improving the flexibility of this approach in practical devices.