SEARCH · Search NASA

Results for “parabolic flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS2018

The ISARA Mission – Flight Demonstration of a High Gain Ka-Band Antenna for 100Mbps Telecom

The NASA sponsored ISARA (Integrated Solar Array and Reflectarray Antenna) mission successfully demonstrated a 100 Mbps Ka-band CubeSat communications capability. The enabling technology is a high gain reflectarray antenna integrated into a modified Pumpkin “Turkey Tail” solar array which wraps around the spacecraft body, essentially requiring near zero volume to accommodate. A simple low gain feed is used to distribute RF power to the reflectarray through free space. The 0.5kg ISARA antenna mass is compatible with the requirements of a 3U (10x10x10 cm3) spacecraft. The ISARA mission validated this approach in a flight technology demonstration. A unique on-orbit measurement system provided accurate measurement of the antenna gain from space. This system demonstrated 100Mbps downlink data rate capability using a relatively simple ground station with a 70cm parabolic reflector antenna. The spacecraft also verified ISARA solar panel output power and demonstrated the operational capability to accurately point the antenna to a Ka-band ground station, a key requirement for a telecom system. ISARA achieved a number of technological firsts. It is believed to be the first reflectarray antenna flown in space, first high gain antenna integrated with solar panels, first calibrated reflectarray antenna gain and pattern measurement performed from space and the first 3U CubeSat to demonstrate 100 Mbps using a small, low-cost ground station.

Martin, Jerami M.↗

NASA NTRS2012

Stability Analysis for HIFiRE Experiments

The HIFiRE-1 flight experiment provided a valuable database pertaining to boundary layer transition over a 7-degree half-angle, circular cone model from supersonic to hypersonic Mach numbers, and a range of Reynolds numbers and angles of attack. This paper reports selected findings from the ongoing computational analysis of the measured in-flight transition behavior. Transition during the ascent phase at nearly zero degree angle of attack is dominated by second mode instabilities except in the vicinity of the cone meridian where a roughness element was placed midway along the length of the cone. The growth of first mode instabilities is found to be weak at all trajectory points analyzed from the ascent phase. For times less than approximately 18.5 seconds into the flight, the peak amplification ratio for second mode disturbances is sufficiently small because of the lower Mach numbers at earlier times, so that the transition behavior inferred from the measurements is attributed to an unknown physical mechanism, potentially related to step discontinuities in surface height near the locations of a change in the surface material. Based on the time histories of temperature and/or heat flux at transducer locations within the aft portion of the cone, the onset of transition correlated with a linear N-factor, based on parabolized stability equations, of approximately 13.5. Due to the large angles of attack during the re-entry phase, crossflow instability may play a significant role in transition. Computations also indicate the presence of pronounced crossflow separation over a significant portion of the trajectory segment that is relevant to transition analysis. The transition behavior during this re-entry segment of HIFiRE-1 flight shares some common features with the predicted transition front along the elliptic cone shaped HIFiRE-5 flight article, which was designed to provide hypersonic transition data for a fully 3D geometric configuration. To compare and contrast the crossflow dominated transition over the HIFiRE-1 and HIFiRE-5 configurations, this paper also analyzes boundary layer instabilities over a subscale model of the HIFiRE-5 flight configuration that was tested in the Mach 6 quiet tunnel facility at Purdue University.

Li, Fei↗

NASA NTRS1986

Compact field color schlieren system for use in microgravity materials processing

A compact color schlieren system designed for field measurement of materials processing parameters has been built and tested in a microgravity environment. Improvements in the color filter design and a compact optical arrangement allowed the system described here to retain the traditional advantages of schlieren, such as simplicity, sensitivity, and ease of data interpretation. Testing was accomplished by successfully flying the instrument on a series of parabolic trajectories on the NASA KC-135 microgravity simulation aircraft. A variety of samples of interest in materials processing were examined. Although the present system was designed for aircraft use, the technique is well suited to space flight experimentation. A major goal of this effort was to accommodate the main optical system within a volume approximately equal to that of a Space Shuttle middeck locker. Future plans include the development of an automated space-qualified facility for use on the Shuttle and Space Station.

Poteet, W. M.↗

NASA NTRS2003

The development of inflatable array antennas

The deployable array antenna using an inflatable or thin-membrane structure has been identified as one of the enabling technologies to achieve low-mass, high packaging efficiency, low cost, and reliable deployment for future NASNJPL spacebome high-gain and large aperture antennas. Array antennas, when compared to parabolic reflectors, although suffering from limited bandwidth performance, offer wide-angle beam scanning capability and a more reliable flat “natural” aperture. To demonstrate the feasibility and capability of this low-mass array technology, three antenna concepts using inflatable and thin-membrane structures were initiated in 1997 at JPL and several breadboard units have been successfully developed. These three concepts are (1) the inflatable phased array, (2) the inflatable reflectarray, and (3) frame-supported thin membrane array antenna. All three concepts utilize the printed microstrip antenna technology. Although all three concepts will be briefly presented, this paper will discuss in more detail of the recent development of the second concept. The first concept of inflatable phased arrays that have been constructed are 3 to 5-meter size L-band dual-polarized synthetic aperture radar (SAR) arrays for Earth remote sensing application. They all consist of a rectangular configuration with inflatable cylindrical tubes that support and tension a multi-layer thin-membrane radiating aperture with microstrip patches and microstrip power divider lines. For the second concept, an inflatable reflectarray was developed for future deep-space telecom applications. It is a 3m Ka-band inflatable reflectarray (1.8 kg/m2). This reflectarray uses inflated torus tubes to support and tension a flat-membrane reflectarray surface. The reflectarray surface emulates a curved parabolic reflecting surface. However, because of its flat surface being a “natural surface”, it is much easier to achieve and more reliable to maintain the required surface tolerance than that of a curved parabola during long space flight. For the third concept, an L-band dual polarized SAR array with a 5m x 3m aperture and 2.5 kg/m2 of mass has recently been demonstrated. It consists of seven foldable panels each having a rectangular frame that supports a two-layer thinmembrane microstrip subarray aperture. Each frame is made of light-weight graphite composite material. The chief advantage of this deployable “frame” concept is that each frame is able to rigidly support an appropriate number of T/R modules and phase shifters to achieve the desired power distribution and beam scanning. Several technology challenges, such as the development of rigidizable inflatable tubes, a controlled deployment mechanism, thin-membrane thermal effects, a low-mass inflation system, membrane mounted T/R modules, means to counter surface tolerance issues, etc. are being investigated and will be discussed in the presentation. With foreseeable success in the development of these challenging areas, the inflatable/thin-membrane array antennas could be mature enough in a few years for actual space flight.

Lou, Michael↗

NASA NTRS2022

Stability Analysis of Streaks Induced by Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗

NASA NTRS2022

Stability Analysis of Streaks Induced By Optimized Vortex Generators

Boundary layer transition↗

NASA NTRS1999

Numerical Investigation of the ARMSEF Arc-Jet

The NASA/JSC 10 MW Atmospheric Reentry Materials and Structures Evaluation Facility (ARMSEF) is used for the development and evaluation of thermal protection systems for manned reentry vehicles. In an effort at better understanding the flow characteristics of an arc-jet wind tunnel and hence the correlation between simulation and actual flight conditions, preliminary numerical analyses have been made. Difficulties in defining inlet boundary conditions to the plenum chamber, where there is very little usable experimental data, are discussed. Two different boundary conditions for the plenum, a straight profile and parabolic profile, are employed to describe the conditions in this very important flow defining region. Comparisons are made to experimental data with the results showing that some type of parabolic or step profile is needed to adequately resolve the strong core flow that is present in the nozzle and plume region. Recommendations are made regarding future efforts in analyzing this challenging flow field.

Cox, Carey F.↗

NASA NTRS1989

An approximate viscous shock layer method for calculating the hypersonic flow over blunt-nosed bodies

The approximate axisymmetric method presented for accurately calculating the surface and flowfield properties of fully viscous hypersonic flow over blunt-nosed bodies incorporates the turbulence model of Cebeci-Smith (1970) and the equilibrium air tables of Hansen (1959). The method is faster than the parabolized Navier-Stokes or viscous shock layer solvers that it could replace for preliminary design determinations. Surface heat transfer and pressure predictions for the present method are comparable with the more accurate viscous shock layer method as well as flight test and wind tunnel data. A starting solution is not required.

Grantz, A. C.↗

NASA NTRS1961

Atmosphere Entries with Vehicle Lift-Drag Ratio Modulated to Limit Deceleration and Rate of Deceleration: Vehicles with Maximum Lift-Drag Ratio of 0.5

An analysis has been made of atmosphere entries for which the vehicle lift-drag ratio was modulated to maintain specified maximum decelerations and/or maximum deceleration rates. The part of the vehicle drag polar used during modulation was from maximum lift coefficient to minimum drag coefficient. The entries were at parabolic velocity and the vehicle maximum lift-drag ratio was 0.5. Two-dimensional trajectory calculations were made for a nonrotating, spherical earth with an exponential atmosphere. The results of the analysis indicate that for a given initial flight-path angle, modulation generally resulted in a reduction of the maximum deceleration to 60 percent of the unmodulated value or a reduction of maximum deceleration rate to less than 50 percent of the unmodulated rate. These results were equivalent, for a maximum deceleration of 10 g, to lowering the undershoot boundary 24 miles with a resulting decrease in total convective heating to the stagnation point of 22 percent. However, the maximum convective heating rate was increased 18 percent; the maximum radiative heating rate and total radiative heating were each increased about 10 percent.

Katzen, Elliott D.↗

NASA NTRSDate not supplied

Comparison of Inlet Broadband Acoustic Liner Predictions to Quiet Technology Demonstrator 3 Flight Data

Companion acoustic liner attenuation predictions and flight data representative of certification conditions are analyzed to determine the validation quality and gain an understanding of current prediction shortcomings. These comparisons are limited to the inlet broadband component of fan noise. Two prediction methods are assessed: a traditional, semiempirical model, and a computational approach with a parabolic duct propagation code coupled with a Ffowcs Williams-Hawkings solver for free-field propagation. The semiempirical method is widely used for aircraft system noise predictions, but does not explicitly account for several physical parameters important for sound attenuation. The computational approach includes these effects, but requires a significant increase in cycle time. For the three-degree-of-freedom (3DOF) liner tested, both methods have a bias error less than 0.5 dB for cutback and takeoff power settings, and a much larger 3–4 dB bias for approach power setting. The standard deviation of each method varies between 1–2 dB for different conditions. The similar performance of both approaches illustrates that, in this instance, the additional complexity of the computational approach does not provide a clear improvement over the semiempirical method. Planned improvements to the numerical grid and source assumptions may result in reevaluation of this conclusion in later work.

aircraft system noise↗

NASA NTRS1981

Gas-laser behavior in a low-gravity environment

In connection with several experiments proposed for flight on the Space Shuttle, which involve the use of gas lasers, the behavior of a He-Ne laser in a low-gravity environment has been studied theoretically and experimentally in a series of flight tests using a low-gravity-simulation aircraft. No fluctuation in laser output above the noise level of the meter (1 part in 1000 for 1 hr) was observed during the low-gravity portion of the flight tests. The laser output gradually increased by 1.4% during a 1.5-hr test; at no time were rapid variations observed in the laser output. A maximum laser instability of 1 part in 100 was observed during forty low-gravity parabolic maneuvers. The beam remained Gaussian throughout the tests and no lobe patterns were observed.

Owen, R. B.↗

NASA NTRS2010

Scanning Mechanism of the FY-3 Microwave Humidity Sounder

Astrium GmbH Germany, developed the scanning equipment for the instrument package of the MicroWave Humidity Sounder (MWHS) flying on the FY-3 meteorological satellite (FY means Feng Yun, Wind and Cloud) in a sun-synchronized orbit of 850-km altitude and at an inclination of 98.8 . The scanning mechanism rotates at variable velocity comprising several acceleration / deceleration phases during each revolution. The Scanning Mechanism contains two output shafts, each rotating a parabolic offset Antenna Reflector. The mechanism is operated in closed loop by means of redundant control electronics. MWHS is a sounding radiometer for measurement of global atmospheric water vapour profiles. An Engineering Qualification Model was developed and qualified and a first Flight Model was launched early 2008. The system is now working for more than two years successful in orbit. A second Flight Model of the Antenna Scanning Mechanism and of its associated control electronics was built and delivered to the customer for application on the follow-on spacecraft that will be launched by the end of 2010.

Schmid, Manfred↗

NASA NTRS2018

Lessons Learned from a Deployment Mechanism for a Ka-band Deployable Antenna for CubeSats

The Ka-band parabolic deployable antenna (KaPDA) is a 0.5 meter diameter antenna which fits in a tiny, CubeSat compatible 10 cm by 10 cm by 16 cm volume. The design evolved from a rough concept in an R&D proposal to a fully flight qualified design, scheduled for launch in May of 2018, in a timeframe of just 4 years. This paper focuses on key lessons learned on maintaining precision through structural depth, use of fixtures and additive manufacturing for fabrication, the design of robust, deterministic mechanisms, and the dangers of friction and press fits

Thomson, Mark↗

NASA NTRS2015

Development of Flight Slit-Jaw Optics for Chromospheric Lyman-Alpha SpectroPolarimeter

In sounding rocket experiment CLASP, I have placed a slit a mirror‐finished around the focal point of the telescope. The light reflected by the mirror surface surrounding the slit is then imaged in Slit‐jaw optical system, to obtain the alpha‐ray Lyman secondary image. This image, not only to use the real‐time image in rocket flight rocket oriented direction selection, and also used as a scientific data showing the spatial structure of the Lyman alpha emission line intensity distribution and solar chromosphere around the observation area of the polarimetric spectroscope. Slit‐jaw optical system is a two off‐axis mirror unit part including a parabolic mirror and folding mirror, Lyman alpha transmission filter, the optical system magnification 1x consisting camera. The camera is supplied from the United States, and the other was carried out fabrication and testing in all the Japanese side. Slit‐jaw optical system, it is difficult to access the structure, it is necessary to install the low place clearance. Therefore, influence the optical performance, the fine adjustment is necessary optical elements are collectively in the form of the mirror unit. On the other hand, due to the alignment of the solar sensor in the US launch site, must be removed once the Lyman alpha transmission filter holder including a filter has a different part from the mirror unit. In order to make the structure simple, stray light measures Aru to concentrate around Lyman alpha transmission filter. To overcome the difficulties of performing optical alignment in Lyman alpha wavelength absorbed by the atmosphere, it was planned following four steps in order to reduce standing time alignment me. 1: is measured in advance refractive index at Lyman alpha wavelength of Lyman alpha transmission filter (121.567nm), to prepare a visible light Firuwo having the same optical path length in the visible light (630nm). 2: The mirror structure CLASP before mounting unit standing, dummy slit and camera standing prescribed position in leading frame is, to complete the internal alignment adjustment. 3: CLASP structure F mirror unit and by attaching the visible light filter, as will plague the focus is carried out in standing position adjustment visible flight products camera. 4: Replace the Lyman alpha transmission filter, it is confirmed by Lyman alpha wavelength (under vacuum) the requested optical performance have come. Currently, up to 3 of the steps completed, it was confirmed in the visible light optical performance that satisfies the required value sufficiently extended. Also, put in Slit‐jaw optical system the sunlight through the telescope of CLASP, it is also confirmed that and that stray light rejection no vignetting is in the field of view meets request standing.

Kubo, Masahito↗

NASA NTRS2001

Follow-on Research Activities for the Rensselaer Isothermal Dendritic Growth Experiment (RIDGE)

The RIDGE effort continues the aegis of the earlier, NASA-sponsored, Isothermal Dendritic Growth Experiment (IDGE) series of experiments through the continued analysis of microgravity data acquired during these earlier space flights. The preliminary observations presented here demonstrate that there are significant differences between SCN and the more anisotropic PVA dendrites. The side branch structure becomes amplified only further behind the tip, and the interface shape is generally wider (i.e. more hyperbolic than parabolic) in PVA than in SCN. These characteristics are seen to affect the process of heat transport. Additionally, the dendrites grown during the fourth United States Microgravity Payload (USMP-4) exhibit time-dependent growth characteristics and may not always have reached steady-state growth during the experiment.

LaCombe, J. C.↗

NASA NTRS2015

Development of Flight Slit-Jaw Optics for Chromospheric Lyman-Alpha SpectroPolarimeter

In sounding rocket experiment CLASP, I have placed a slit a mirror-finished around the focal point of the telescope. The light reflected by the mirror surface surrounding the slit is then imaged in Slit-jaw optical system, to obtain the a-ray Lyman secondary image. This image, not only to use the real-time image in rocket flight rocket oriented direction selection, and also used as a scientific data showing the spatial structure of the Lyman alpha emission line intensity distribution and solar chromosphere around the observation area of the polarimetric spectroscope. Slit-jaw optical system is a two off-axis mirror unit part including a parabolic mirror and folding mirror, Lyman alpha transmission filter, the optical system magnification 1x consisting camera. The camera is supplied from the United States, and the other was carried out fabrication and testing in all the Japanese side. Slit-jaw optical system, it is difficult to access the structure, it is necessary to install the low place clearance. Therefore, influence the optical performance, the fine adjustment is necessary optical elements are collectively in the form of the mirror unit. On the other hand, due to the alignment of the solar sensor in the US launch site, must be removed once the Lyman alpha transmission filter holder including a filter has a different part from the mirror unit. In order to make the structure simple, stray light measures Aru to concentrate around Lyman alpha transmission filter. To overcome the difficulties of performing optical alignment in Lyman alpha wavelength absorbed by the atmosphere, it was planned 'following four steps in order to reduce standing time alignment me. 1. is measured in advance refractive index at Lyman alpha wavelength of Lyman alpha transmission filter (121.567nm), to prepare a visible light Firuwo having the same optical path length in the visible light (630nm).2. The mirror structure CLASP before mounting unit standing, dummy slit and camera standing prescribed position in leading frame is, to complete the internal alignment adjustment. 3. CLASP structure F mirror unit and by attaching the visible light filter, as will plague the focus is carried out in standing position adjustment visible flight products camera. 4. Replace the Lyman alpha transmission filter, it is confirmed by Lyman alpha wavelength (under vacuum) the requested optical performance have come. Currently, up to 3 of the steps completed, it was confirmed in the visible light optical performance that satisfies the required value sufficiently extended. Also, put in Slit-jaw optical system the sunlight through the telescope of CLASP, it is also confirmed that and that stray light rejection no vignetting is in the field of view meets request standing.

chromospheric↗

NASA NTRS1993

Materials science on parabolic aircraft: The FY 1987-1989 KC-135 microgravity test program

This document covers research results from the KC-135 Materials Science Program managed by MSFC for the period FY87 through FY89. It follows the previous NASA Technical Memorandum for FY84-86 published in August 1988. This volume contains over 30 reports grouped into eight subject areas covering acceleration levels, space flight hardware, transport and interfacial studies, thermodynamics, containerless processing, welding, melt/crucible interactions, and directional solidification. The KC-135 materials science experiments during FY87-89 accomplished direct science, preparation for space flight experiments, and justification for new experiments in orbit.

Curreri, Peter A.↗

NASA NTRS1987

Research in materials processing using a low gravity simulation aircraft

The feasibility of performing materials experiments aboard the NASA KC-135 low gravity simulation aircraft is demonstrated. The vehicle serves as a research platform which flies parabolic maneuvers. Experiments which have been conducted on board the aircraft are outlined and particular attention is given to tests utilizing optical measurement techniques such as interferometry, schlieren, and holography. It is noted that the KC-135 can be used for crew training, flight hardware checkout, conceptual development, self-sufficient experiments, and research in support of and leading to space flight experiments.

Owen, Robert B.↗