Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample minimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Rapid determination of 226Ra in environmental samples

A new rapid method for the determination of {sup 228}Ra in natural water samples has been developed at the SRNL/EBL (Savannah River National Lab/ Environmental Bioassay Laboratory) that can be used for emergency response or routine samples. While gamma spectrometry can be employed with sufficient detection limits to determine {sup 228}Ra in solid samples (via {sup 228}Ac) , radiochemical methods that employ gas flow proportional counting techniques typically provide lower MDA (Minimal Detectable Activity) levels for the determination of {sup 228}Ra in water samples. Most radiochemical methods for {sup 228}Ra collect and purify {sup 228}Ra and allow for {sup 228}Ac daughter ingrowth for ~36 hours. In this new SRNL/EBL approach, {sup 228}Ac is collected and purified from the water sample without waiting to eliminate this delay. The sample preparation requires only about 4 hours so that {sup 228}Ra assay results on water samples can be achieved in < 6 hours. The method uses a rapid calcium carbonate precipitation enhanced with a small amount of phosphate added to enhance chemical yields (typically >90%), followed by rapid cation exchange removal of calcium. Lead, bismuth, uranium, thorium and protactinium isotopes are also removed by the cation exchange separation. {sup 228}Ac is eluted from the cation resin directly onto a DGA Resin cartridge attached to the bottom of the cation column to purify {sup 228}Ac. DGA Resin also removes lead and bismuth isotopes, along with Sr isotopes and {sup 90}Y. La is used to determine {sup 228}Ac chemical yield via ICP-MS, but {sup 133}Ba can also be used instead if ICP-MS assay is not available. Unlike some older methods, no lead or strontium holdback carriers or continual readjustment of sample pH is required.

54 ENVIRONMENTAL SCIENCES↗

Simulated Irradiation of Samples in HFIR for use as Possible Test Materials in the MPEX (Material Plasma Exposure Experiment) Facility

The importance of Plasma Material Interaction (PMI) is a major concern in fusion reactor design and analysis. The Material-Plasma Exposure eXperiment (MPEX) facility will explore PMI under fusion reactor plasma conditions. Samples with accumulated displacements per atom (DPA) damage produced by irradiations in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) will be studied in the MPEX facility. The project presented in this paper involved performing assessments of the induced radioactivity and resulting radiation fields of a variety of potential fusion reactor materials. The scientific code packages MCNP and SCALE were used to simulate irradiation of the samples in HFIR; generation and depletion of nuclides in the material and the subsequent composition, activity levels, gamma radiation fields, and resultant dose rates as a function of cooling time. These state-of-the-art simulation methods were used in addressing the challenge of the MPEX project to minimize the radioactive inventory in the preparation of the samples for inclusion in the MPEX facility.

Ellis, Ronald James↗

Manufacturing Dissolvable Alloy Components using ShAPE: A Study on Solid Phase Processing of Mg-W Composites and WJ11 Alloys

Dissolvable alloys and composites are an emerging class of materials that demonstrate tailored sorptivity in corrosive environments. This work explored the viability of solid phase processing (SPP) techniques, namely the shear assisted processing and extrusion (ShAPETM) method, to manufacture dissolvable magnesium composites and alloys components such as rods and tubes. The study also determined the effects of material composition and manufacturing process conditions on material microstructures developed during SPP and the resulting performance of the components. Explicit properties of interest included ultimate tensile strength, ultimate compressive strength, and yield strength. The application fields of interest for dissolvable alloys were identified as oil-and-gas operations and biomedical implants. Accordingly, PNNL collaborated with industrial and academia partners, Fortek Industries, Houston and University of Pittsburgh, during the course of this project for material and ShAPE process development. PNNL determined the viability of the using ShAPE to process the custom-designed materials provided by the project partners. This was done by identifying process parameters such as tool rotation rate, tool plunge rate, and process cooling optimal for manufacturing components with consolidated microstructures. Subsequently, PNNL also performed microstructural characterization on unprocessed and processed samples and mechanical property testing. One of the major findings from this work is that ShAPE was able to manufacture dissolvable magnesium composite and alloy rods and tubes with consolidated homogeneous microstructures and minimal macroscale defects on component surfaces. It was observed that samples processed via ShAPE demonstrated an average grain size < 2 - 5 µm, which was markedly lower than that of the precursors with 8 – 13 µm grains. Results showed that the ShAPE synthesized dissolvable magnesium composite and alloy strength was on par with or better than those components that were manufactured using traditional manufacturing processes such as forging and extrusion. It is noteworthy that the ShAPE samples were made with considerably lower number of process steps.

36 MATERIALS SCIENCE↗

Distribution of Pb-210 in Spanish Soils: Study of the Atmospheric Contribution

The vertical distribution of activity and inventories of atmospheric Pb-210 is being studied in Spanish soils, aiming to establish the reference levels in the zone, based on the type of soil and the annual rainfall. A homogeneous distribution grid (approx. 150x150 km each cell) has been established covering the peninsular land, trying to combine the varying soil types (remaining undisturbed for the last 50 years) and the closeness to meteorological stations. Sampling has been performed by extracting undisturbed soil cylinders of 6 cm diameter and 120 cm length, with an impact penetrometer, and the soil cores have been sectioned in slices of 3 cm thick. The analysis of Pb-210 has been performed using a gamma spectrometry system with coaxial HPGe detector sensitive at low energies (46.5 keV emission). The geometry of measured samples is thin enough (approx. 2 cm) to minimize self-absorption corrections. The work presents the results obtained so far. The Pb-210 activity profiles exhibit the characteristic decreasing shape with depth, showing maximum levels at the surface, and reaching the equilibrium activity with Ra-226 at a maximum depth depending on different environmental conditions. The unsupported Pb-210 inventory values are in the usual range (1000-5000 Bq/m{sup 2}), showing a positive correlation with the averaged annual rainfall. These reference levels could be used in posterior studies of anthropogenic alteration of soils, evaluation of erosion and desertification processes.

54 ENVIRONMENTAL SCIENCES↗

Deuterium plasma induced preferential erosion in ultra-high temperature ceramics TiB 2 and ZrB 2 *

Abstract Steady-state deuterium plasma exposures were performed on ultra-high temperature ceramics titanium diboride (TiB 2 ) and zirconium diboride (ZrB 2 ) using the PISCES-RF linear plasma device (LPD) as early screening for first wall, plasma-facing applications. Deuterium plasma exposures were performed using 40 eV ion energies at 240, 525, and 800 °C sample temperatures and 90 eV ion energies at 240 °C sample temperatures to analyze TiB 2 and ZrB 2 surface morphology and chemistry evolution behavior. Post-plasma exposure chemistry characterization of the near surface ( < 50 nm) region of the samples all show transition metal enrichment, indicating boron preferential erosion. Transition metal to boron fractions vary with plasma exposure temperature under the 40 eV ion energy; metal enrichment is maximized at 800 °C and then minimized at 525 °C. SEM micrographs of all plasma exposed sample surfaces show no significant or noticeable plasma induced damage from cracking or blistering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Serial crystallography using automated drop dispensing

Automated, pulsed liquid-phase sample delivery has the potential to greatly improve the efficiency of both sample and photon use at pulsed X-ray facilities. In this work, an automated drop on demand (DOD) system that accelerates sample exchange for serial femtosecond crystallography (SFX) is demonstrated. Four different protein crystal slurries were tested, and this technique is further improved here with an automatic sample-cycling system whose effectiveness was verified by the indexing results. Here, high-throughput SFX screening is shown to be possible at free-electron laser facilities with very low risk of cross contamination and minimal downtime. The development of this technique will significantly reduce sample consumption and enable structure determination of proteins that are difficult to crystallize in large quantities. This work also lays the foundation for automating sample delivery.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Countering sensor drift in x-ray micrscopy with fast and robust optimal control

In X-ray microscopy it is imperative that the relative position between the optics stage, that carries the X-ray focusing optics, and the sample stage follow a certain trajectory while either the optics or sample stage is being scanned. Main challenges in achieving this requirement include - open loop drift, environmental disturbance, measurement noise, sensor drift, and control hardware limit. The state-of-the-art in X-ray microscopy at Advanced Photon Source (APS) at Argonne National Laboratory (ANL) features an H ∞ control architecture applied to only the optics stage or both the optics and sample stage, achieving the objectives of large tracking bandwidth over 200 Hz, good positioning resolution on the order of nanometers, rejection of environmental disturbance, attenuation of measurement noise, good Xray diffraction image resolution and increased imaging bandwidth. However, an unaddressed issue in our existing robust control design is that the sensors and the fixtures that hold the sensors drift with time due to changing air temperature in the APS beamline. Since the drift of sensor itself is not measured, it affects the relative position between the focusing optics and sample resulting into imaging artifacts and reduced image resolution. In this article, we demonstrate the rejection of the sensor drift by directly measuring the displacement of the sensor with respect to the global reference frame. Both the measured sensor displacement (i.e. sensor drift) and optics stage displacement are incorporated in the H ∞ control architecture to achieve the above mentioned objectives in addition to minimal relative displacement between the optics stage and the sample stage. This will improve the Xray image resolution and reduce image artifacts.

Robust Control↗

Atom Probe Tomography for understanding microstructural and chemical changes in nuclear materials

Atom Probe Tomography (APT) is routinely employed to determine 3D microstructure and chemistry changes in structural materials used in reactor to understand irradiation effect. These findings help to correlate changes to mechanical and physical properties of nuclear materials which are subjected to extreme reactor conditions. With safety and economics of a reactor in mind, it is essential to be able to predict the changes in the fuel composition and microstructure as a function of burnup. Also, there is current need to develop advanced fuels with improved properties and performance which requires the experimental data on changes in microstructure, physical and chemical properties after irradiation for feedback process. A novel approach is presented to determine the local burnup in irradiated fuels using isotopic quantification obtained by Atom Probe Tomography (APT). Considering the volume of sample used (<100?µm3) for APT experiments using the lift-out process in a scanning electron microscope equipped with a Focused Ion Beam (FIB), the presented method determines the local burnup from a nuclear fuel, where a minimal amount of waste is produced. In this work, three samples were analyzed with different burnup conditions to quantify the isotopes of 235U, 236U, and 238U for burnup calculation in the irradiated metallic U–7Mo dispersion fuel. The calculated values were found in excellent agreement with MCNP calculations. With regard to structural materials, one of the primary factors limiting the utilization of fuel rods of Zr alloys is hydrogen pick up during oxidation. Past experimental studies have shown that the hydrogen pickup in Zirconium alloys is influenced by the alloy composition as well by irradiation temperature and neutron dose. Oftentimes, it is not feasible to carry out comprehensive studies on understanding the microstructural evolution in neutron irradiated materials since in reactor irradiation programs are extremely costly, lengthy and logistically complicated. The use of ion irradiation as a substitute has grown in recent years for several reasons including less radioactivity, faster irradiations and lower costs. In the framework of the MUZIC 3 project, samples of Zircaloy-4 have been proton and Zr2+ irradiated at the Michigan Ion Beam Lab (MIBL) facility with aim to create a microstructure that is similar to that observed after in-reactor service. The temperature of the environment is adjusted to compensate for the higher dose rate, as has been done previously. As a first step in this project the irradiated microstructures have been characterized using Transmission Electron Microscopy and Atom Probe Tomography to elucidate the microstructural changes, including precipitate amorphization and dissolution and the formation of dislocation loops. This presentation plans to highlight initial finding of this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An environmental sample chamber for reliable scanning transmission x-ray microscopy measurements under water vapor

We have designed, fabricated, and tested a compact gas-phase reactor for performing in situ soft x-ray scanning transmission x-ray microscopy (STXM) measurements. The reactor accommodates many gas atmospheres, including reactive or corrosive gasses, but was designed specically to address the needs of measurements under water vapor. An on-board sensor measures the relative humidity and temperature inside the reactor, minimizing uncertainties associated with measuring these quantities outside the instrument. The reactor mounts directly to the existing sample holder used in the majority of STXM instruments around the world and installs with minimal instrument reconguration. Using the reactor contributes over 85% less additional absorption compared to lling the STXM chamber with process gas, and results in much more stable imaging conditions. The reactor is in use at the STXM instruments at beamlines 11.0.2 and 5.3.2.2 at the Advanced Light Source.

Environmental Molecular Sciences Laboratory↗

A novel approach to determine the local burnup in irradiated fuels using Atom Probe Tomography (APT)

A novel approach is presented to determine the local burnup in irradiated fuels using isotopic quantification obtained by Atom Probe Tomography (APT). Considering the volume of sample used (<100 μm 3 ) for APT experiments using the lift-out process in a scanning electron microscope equipped with a Focused Ion Beam (FIB), the presented method determines the local burnup from a nuclear fuel, where a minimal amount of waste is produced. In this work, three samples were analyzed with different burnup conditions: as received low enriched 19.8% U-235, intermediate burnup (~52% U-235 fissioned) and high burnup (~69% U-235 fissioned) U–Mo fuel. APT is used to quantify the isotopes of 235 U, 236 U, 238 U, 239 Pu and 237 Np for burnup calculation in the irradiated metallic U–7Mo dispersion fuel. The equation used to estimate the burnup of fuels is derived by considering that the initial counts of U is equal to the sum of remaining atoms of U isotopes and all the U reactions undergone during irradiation. Here, this method provides U enrichment and local burnup with an unprecedented high spatial resolution based on quantification of isotopic ratios of U.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

A high pressure cell for supercritical CO{sub 2} on-line chemical reactions studied with x-ray techniques

A versatile high pressure X-ray sample cell has been developed for conducting in situ time-resolved X-ray scattering experiments in the pressure and temperature regime required (pressures up to 210 bars and temperatures up to 120 °C) for chemical reactions in supercritical fluids. The large exit opening angle of the cell allows simultaneous performance of SAXS-WAXS experiments. Diamond windows are used in order to benefit from the combination of maximum strength, minimal X-ray absorption and chemical inertia. The sample cell can also be utilised for X-ray spectroscopy experiments over a wide range of photon energies. Results of the online synthesis of a block copolymer, poly(methyl methacrylate-block-poly(benzyl methacrylate), by Reversible Addition-Fragmentation Chain Transfer (RAFT) in a supercritical CO{sub 2} dispersion polymerisation will be discussed. The contribution of the density fluctuations, as function of temperature, to the X-ray scattering signal has been quantified in order to allow appropriate background subtractions.

36 MATERIALS SCIENCE↗

Development of field-based separations for the rapid identification of uranium and plutonium

The development of rapid, radioanalytical techniques to separate uranium and plutonium from complex, field samples are needed for the timely and accurate determination of nuclear material origin, and processing activities. Widespread use of nuclear power and technology in the world has increased demands on analytical laboratories from the monitoring of numerous low-level, environmental samples with variable compositions. Environmental sampling has proven to be one of the strongest technical measures for detecting nuclear material and activities. With the increase in sampling demands, new technologies must offer improvements such as automation, high throughput, reproducible chemical separations, short analysis times, and reduced costs to be effective. We have been developing a portable, separations system for uranium (U) and plutonium (Pu) separations based upon selective extraction of target elements using an extraction chromatographic resin which would allow for simple and fast identifcation when coupled with the appropriate sample digestor and detection systems. The microfluidic design minimizes elution volumes and concentrates the elements of interest in a purified stream. Flowsheet development and testing was demonstrated on a single, micro-column system with an acidified, iron, uranium, and plutonium nitrate stream. The recovery of Pu was optimized by examining various reducing agents at different concentrations for rapid, quantitative recovery from the flow-through design. Quantitative recovery and high selectivity of U and Pu was achieved in the appropriate stripping stages and provided purified and concentrated U and Pu streams. The microfluidic system suggests automation in a small, footprint unit while exploiting the in-line processing of extraction chromatographic resins as the primary means of concentrating the radionuclides from the raw acidic feed and separating the elements into purified streams.

Extraction Chromatography↗

Coherent J/ψ photoproduction at forward rapidity in ultra-peripheral Pb–Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV

The ALICE collaboration performed the first rapidity-differential measurement of coherent J/ψ photoproduction in ultra-peripheral Pb–Pb collisions at a center-of-mass energy $ \sqrt{s_{NN}}$=5.02 TeV. The J/ψ is detected via its dimuon decay in the forward rapidity region (-4.0 < γ < -2.5) for events where the hadronic activity is required to be minimal. The analysis is based on an event sample corresponding to an integrated luminosity of about 750 μb -1 . The cross section for coherent J/ψ production is presented in six rapidity bins. The results are compared with theoretical models for coherent J/ψ photoproduction. These comparisons indicate that gluon shadowing effects play a role in the photoproduction process. The ratio of ψ' to J/ψ coherent photoproduction cross sections was measured and found to be consistent with that measured for photoproduction off protons.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Basic properties of eutectic chloride salts NaCl-KCl-ZnCl 2 and NaCl-KCl-MgCl 2 as HTFs and thermal storage media measured using simultaneous DSC-TGA

Concentrated solar power (CSP) technologies tend to work at high temperatures for better energy efficiency, which need high temperature heat transfer fluids (HTF) and thermal storage. A good HTF should have low melting point and be thermally stable at high temperatures. A thermal storage medium needs a high heat capacity in order to store more energy in per unit of mass or volume. The objective of this work is to study the basic thermophysical properties of several eutectic molten salts for HTF and thermal storage media, which can work at upper limit temperatures of 850 °C. The eutectic salts are mixtures by NaCl-KCl-ZnCl 2 , and by NaCl-KCl-MgCl 2 , respectively. The heat capacity, melting point, and heat of fusion of the eutectic salts at different temperatures were measured using Differential Scanning Calorimetry (DSC) and Thermal Gravimetric Analysis (TGA) simultaneously. Details of the measurements and obtained experience of operating the equipment are provided in the work. For each of the eutectic salts multiple samples were tested to check repeatability and to minimize random errors. Finally, in theoretical analysis, mixing rules from literature was used to estimate the heat capacity of the new HTFs, which showed good agreement with experimental data.

14 SOLAR ENERGY↗

Electrochemical properties of poly(ethylene oxide) electrolytes above the entanglement threshold

The ion transport in electrolytes depends on three transport coefficients, conductivity (κ), salt diffusion coefficient (D), and the cation transference number with respect to the solvent velocity ($t_+^0$), and the thermodynamic factor ($T_f$). Current methods for determining these parameters involve four separate experiments, and the coupled nature of the equations used to determine them generally results in large experimental uncertainty. We present data obtained from 64 independent polymer electrolytes comprising poly(ethylene oxide) (PEO) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. The molecular weights of PEO ranged from 5 to 275 kg mol -1 ; these samples are all above the entanglement threshold. We minimize the experimental uncertainty in transport and thermodynamic measurements by exploiting the fact that ion transport in entangled polymer electrolytes should be independent of molecular weight. The dependence of $κ, D, t_+^0$, and $T_f$ as a function of salt concentration in the range 0.035 ≤ r ≤ 0.30 are presented with a 95% confidence interval, where r is the molar ratio of lithium ions to ethylene oxide monomer units. While κ, D, and $T_f$ are all positive as required by thermodynamic constraints, there is no constraint on the sign of $t_+^0$. We find that $t_+^0$ is negative in the salt concentration range of 0.093 ≤ r ≤ 0.189.

25 ENERGY STORAGE↗

Effect of Al 2 O 3 coating on fretting wear performance of Zr alloy

Fretting wear caused by flow-induced vibration (FIV) is one of the predominant tribological failure modes in nuclear power plants and industry. This paper presents an experimental study of the effect on fretting performance of alumina (Al 2 O 3 ) coatings produced by atomic layer deposition (ALD) on Zirlo (a Zr alloy), a common nuclear fuel cladding alloy. A coating with uniform thickness of about 750 nm was deposited onto a Zirlo flat. Because the typical thickness of fuel cladding is 1 mm, an ultra-thin coating is required. The hardness and elastic modulus of the ALD coating were measured by nano-indentation techniques. With a pin-on-flat contact configuration in low-amplitude reciprocating contact, fretting performance was measured for uncoated Zirlo, Al2O 3 -coated Zirlo, and Al 2 O 3 -coated Zirlo followed by heat treatment. Results showed that the as-deposited Al 2 O 3 coating provided slight improvement in fretting wear performance. However, the heat-treated coating showed two orders of magnitude reduction in fretting wear of the Zr alloy. Wear in the uncoated material involves some local plastic deformation and debris accumulation at the contact interface. In the Al 2 O 3 -coated material, wear occurred by transfer of transparent Al 2 O 3 oxide into the steel pin counterface. Localized removal of coating from the Zirlo alloy flat resulted in a “shark whale” pattern in a scanning electron microscopy image. There was minimal debris accumulation with the heat-treated sample.

36 MATERIALS SCIENCE↗

A shock tube with a high-repetition-rate time-of-flight mass spectrometer for investigations of complex reaction systems

A conventional membrane-type stainless steel shock tube has been coupled to a high-repetition-rate time-of-flight mass spectrometer (HRR-TOF-MS) to be used to study complex reaction systems such as the formation of pollutants in combustion processes or formation of nanoparticles from metal containing organic compounds. Opposed to other TOF-MS shock tubes, our instrument is equipped with a modular sampling unit that allows to sample with or without a skimmer. The skimmer unit can be mounted or removed in less than 10 min. Thus, it is possible to adjust the sampling procedure, namely, the mass flux into the ionization chamber of the HRR-TOF-MS, to the experimental situation imposed by species-specific ionization cross sections and vapor pressures. The whole sampling section was optimized with respect to a minimal distance between the nozzle tip inside the shock tube and the ion source inside the TOF-MS. The design of the apparatus is presented and the influence of the skimmer on the measured spectra is demonstrated by comparing data from both operation modes for conditions typical for chemical kinetics experiments. The well-studied thermal decomposition of acetylene has been used as a test system to validate the new setup against kinetics mechanisms reported in literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗