Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Error field measurements and correction on MUSE permanent magnet stellarator

The magnetic field topology and error fields are measured in the MUSE permanent magnet stellarator with an electron beam and fluorescent rod. The effective magnetization of the magnets is determined by measuring rational flux surface locations. Electron magnetic drift effects must be considered self-consistently due to the small magnetic shear on MUSE. Error fields are characterized by flux surface shape deviation and magnetic island chain width and phase. Error fields are then corrected by adjusting the permanent magnet (PM) holders as rigid bodies. Resonant error fields are on the order of or smaller than 3 x 10 -6 of the toroidal field after correction and surface shape matches well with the design. Resonant components of the quasi-symmetry deviation are estimated, using a novel magnetic drift measurement, to be in the 10 −4 range. The PM approach is validated as a low-cost and precise way to build optimized stellarators.

electron beam mapping↗
DOE OSTI2025

Stochastic parametric skeletal dosimetry model for humans: Anatomical-morphological basis and parameter evaluation

Radiation exposure of the hematopoietic system that results in a radiation dose to bone marrow of more than 100 mGy leads to an increase in the risk of leukemia in humans. Excess relative risk of leukemia was observed in cohorts whose members lived in the territories of the Southern Urals that were radioactively contaminated in the 1950s. As part of the dosimetric support of epidemiological studies of these cohorts, an original methodology for stochastic bone dosimetric modeling was developed, termed the Stochastic Parametric Skeletal Dosimetry (SPSD) model. The purpose of this work was to present the anatomical and morphological bases of the SPSD model, which includes an assessment of the parameters of the microstructure of the trabecular bone in the hematopoietic areas of the human skeleton, as well as a description of the macrostructural division (segmentation) of hematopoietic areas into simple bone segments. As a result, an anatomical-morphological basis of the SPSD model was created based on published data. Data collection work included the analysis of original articles, atlases, manuals, monographs and the formation of primary data files. Data on the duration of hematopoiesis in various parts of the skeleton; and data on age-related changes in the microstructure and linear dimensions of human bones and their segments were analyzed. The paper describes the full set of parameters to be used for the dosimetric model for newborns, children aged 1, 5 and 10 years, as well as for adolescents aged 15 years and adults; for the latter, sex differences in bone size were considered. In total, the SPSD model includes 289 unique basic (bone) phantom segments, each of which is described by 7 or more parameters describing the microstructure, thickness of the cortical layer and linear dimensions. Population variability was estimated for each parameter. The approach to SPSD modeling, i.e., the use of simple geometric shapes, was successfully verified using independent datasets on bone masses and volumes.

Science & Technology - Other Topics↗
DOE OSTI2025

Characterization of Neutron Emission Rates of Commercial 252 Cf Sources

Accurate knowledge of 252 Cf neutron emission rates is critical for modeling and fast-neutron experiments, yet commercial sources are often supplied without traceable calibration or uncertainty estimates. This report describes a method to characterize 252 Cf sources using a pulse-shape-discrimination (PSD) scintillator. The scintillator was efficiency-calibrated against a time-tagged 252 Cf fission chamber manufactured at ORNL over 40 years ago. Isotopic evolution of the calibration source was modeled using Bateman equations to account for changes in the effective average neutrons per fission at the time of measurement. The calibrated scintillator was then used to measure absolute emission rates of several commercial 252 Cf sources, revealing deviations of up to 12% from nominal manufacturer values. This methodology provides a practical approach for establishing uncertainty-quantified 252 Cf neutron emission rates, improving fidelity in simulations and supporting the accurate interpretation of measurements.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
NASA NTRS1973

Stellar Bragg crystal X-ray spectrometry on OSO-1

A high sensitivity crystal X-ray spectrometer for use on the Orbiting Solar Observatory (mission 1) satellite is described. This instrument will be used to obtain both solar and stellar spectra in the energy range 2 to 8 keV. In the stellar mode, the shape of the continua, the strength of lines, and the strength of recombination and absorption edge were determined. If lines or edges are detected, such data will provide direct evidence regarding the physical conditions in the emitting and absorbing regions. If only upper bounds are established, the data can be used to constrain theoretical models. In any case, precise continuum shapes will be established for a number of the brighter X-ray sources. Numerical estimates of the sensitivity of the instrument for these various purposes are given.

Landecker, P. B.↗
NASA NTRS1979

The diffuse X-ray background spectrum from 3 to 50keV

The spectrum of the extragalactic diffuse X-ray background was measured with the GSFC cosmic X-ray experiment on HEAO-1 for regions of the sky away from known point sources and more than 20 deg from the galactic plane. A total exposure of 80 sq m-sec-sr is available at present. Free-free emission from an optically thin plasma of 40 plus or minus 5 keV provides an excellent description of the observed spectrum from 3 to 50 keV. This spectral shape is confirmed by measurements from 5 separate layers of three independent detectors. With an estimated absolute precision of about 10 percent, the intensity of the emission at 10 keV is 3.2 keV/keV-sq cm-sec-sr, a value consistent with the average of previously reported spectra. No other spectral features, such as iron line emission, are evident. This spectrum is not typical of known extragalactic objects. A uniform hot intergalactic medium of approximately 36 percent of the closure density of the universe would produce such a flux, although non-uniform models indicating less total matter are probably more realistic.

Marshall, F. E.↗
NASA NTRS1980

The diffuse X-ray background spectrum from 3 to 50 keV

The spectrum of the extragalactic diffuse X-ray background has been measured with the GSFC Cosmic X-ray Experiment on HEAO 1 for regions of the sky away from known point sources and more than 20 deg from the galactic plane. A total exposure of 80 sq m-s-sr is available at present. Free-free emission from an optically thin plasma of 40 plus or minus 5 keV provides an excellent description of the observed spectrum from 3 to 50 keV. This spectral shape is confirmed by measurements from five separate layers of three independent detectors. With an estimated absolute precision of about 10%, the intensity of the emission at 10keV is 3.2 keV/keV/sq cm/s/sr, a value consistent with the average of previously reported spectra. A uniform hot intergalactic medium of approximately 36% of the closure density of the universe would produce such a flux, although nonuniform models indicating less total matter are probably more realistic.

Marshall, F. E.↗
NASA NTRS1983

Radar observations of asteroid 1685 Toro

The present results of 13 cm wavelength radar observations of the asteroid 1685 Toro, conducted at the Arecibo Observatory in July 1980, yield radar spectra which reveal correlated and approximately twofold variations in radar cross section and spectral bandwidth as functions of rotational phase, with two maxima and two minima per rotation cycle. In combination with the photopolarimetric results of Dunlap et al. (1973), the observations presently reported offer constraints on Toro's size, shape, and surface properties. Modeling Toro as a homogeneously scattering ellipsoid yields weighed least squares estimates for the lengths of the equatorial semiaxes and a nearly Lambertian scattering law.

Ostro, S. J.↗
NASA NTRS1983

Model error estimation for distributed systems described by elliptic equations

A function space approach is used to develop a theory for estimation of the errors inherent in an elliptic partial differential equation model for a distributed parameter system. By establishing knowledge of the inevitable deficiencies in the model, the error estimates provide a foundation for updating the model. The function space solution leads to a specification of a method for computation of the model error estimates and development of model error analysis techniques for comparison between actual and estimated errors. The paper summarizes the model error estimation approach as well as an application arising in the area of modeling for static shape determination of large flexible systems.

Rodriguez, G.↗
NASA NTRS1984

Quantitative non-destructive evaluation of composite materials based on ultrasonic wave propagation

The size, shape, and orientation of damage correlates well between the polar backscatter technique and the deply technique. There is good quantitative correlation between the areas of damage indicated by the two techniques. These results suggest that the polar backscatter technique is sensitive to specific orientations of damage. The polar backscatter technique provides a good qualitative image of the size and shape of the largest zone of damage in each of the principal orientations. A quantitative estimate of the extent of these largest damage zones is obtained from the polar backscatter technique. The selective sensitivity of polar backscatter provides a useful tool for further studies of the mechanisms of impact damage in graphite fiber reinforced composite laminates.

Miller, J. G.↗
NASA NTRS1986

Correlation of Ultrasonic Polar Backscatter with the Deply Technique for Assessment of Impact Damage in Composite Laminates

Ultrasonic polar backscatter, a quantitative NDE technique introduced by O'Donnell and Miller (1981), was used to characterize impact damages in a 16-ply graphite-epoxy laminate. The results were correlated with the results obtained by the destructive deply technique of Freeman (1984). The size, shape, and orientation of damage correlated well between the polar backscatter technique and the deply technique. There was good quantitative correlation between the areas of damage indicated by the two techniques, suggesting that the polar backscatter technique is sensitive to specific orientations of damage. The polar backscatter technique provides a good qualitative image of the size and shape of the largest zone of damage in each of the principal orientations; a quantitative estimate of the extent of these largest damage zones can then be obtained.

Blodgett, E. D.↗
NASA NTRS1987

Absorption of isotropic radiation

Estimates of the absorption of isotropic radiation are given for an absorbing medium whose geometrical shape is either a plane-parallel sided slab or a cylinder. By including the directional variation of absorption path length, the results show appreciable differences to the 'unidirectional radiation' formulas.

Harries, Wynford L.↗
NASA NTRS1987

A new radar technique for satellite rainfall algorithm development

A potential new radar parameter was investigated for measuring rainfall, namely the summation of the phase shifts at horizontal and vertical polarizations due to propagation through precipitation. The proposed radar technique has several potential advantages over other approaches because it is insensitive to the drop size distribution and to the shapes of the raindrops. Such a parameter could greatly assist the development of satellite rainfall estimation algorithms by providing comparative measurements near the ground. It could also provide hydrologically useful information for such practical applications as urban hydrology. Results of the investigation showed that the parameters can not be measured by radar. However, a closely related radar parameter, propagation differential phase shift, can be readily measured using a polarization diversity radar. It is recommended that propagation differential phase shift be further investigated and developed for radar monitoring of rainfall using a polarization agile radar. It is also recommended that a prototype multiple frequency microwave link be constructed for attenuation measurements not possible by existing radar systems.

Jameson, Arthur R.↗
NASA NTRS1991

On the anomalies in single-jet hover suckdown data

The data from nine different investigations of the suckdown induced in ground effect by a single jet issuing from plates of various sizes and shapes have been examined and compared. The results show that the generally accepted method for estimating suckdown significantly underestimated the suckdown for most of the configurations. The study identified several factors that could contribute to the differences. These include ground board size, plate edge effects, jet flow quality, jet impingement angle, the size of the chamber in which the tests were run, and obstructions in the region above the model. Most of these factors have not been investigated and in many cases items such as the size of the test chamber, jet flow quality, ground board size, etc., have not even been shown in the documents reporting the investigation. A program to investigate the effects of these factors is recommended.

Kuhn, Richard E.↗
NASA NTRS1999

Directional Solidification of Pure Succinonitrile and a Succinonitrile-Acetone Alloy

An experimental study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol.% acetone alloy (SCN-1.0 mol.% ACE) has been performed. Experiments involving both a stationary thermal field (no-growth case) and a translating thermal field (growth case) were conducted. Growth rates of 2 and 40 micrometers/s were investigated. For the pure SCN experiments, the velocity field in the melt was estimated using video images of seed particles in the melt. Observations of the seed particles indicate that a primary longitudinal convective cell is formed. The maximum velocity of two different particles which traveled along similar paths was the same and equal to 1.49 +/- 0.01 mm/s. The general accuracy of velocity measurements is estimated to be +/- 0.08 mm/s, though the data shows consistency to within +/- 0.02 mm/s. The shape of the solid/liquid interface was also quantitatively determined. The solid/liquid interface was stable (non-dendritic and non-cellular) but not flat; rather it was significantly distorted by the influence of convection in (he melt and, for the growth case, by the moving temperature boundary conditions along the ampoule. It was found that the interface shape and position were highly dependent on the alignment of the ampoule in the apparatus. Consequently, the ampoule was carefully aligned for all experiments. The values for front location agree with those determined in previous experiments. For the alloy experiments, the solid/liquid interface was determined to be unstable at growth rates greater than 2.8 micrometers/s, but stable for the cases of no-growth and growth at 2 micrometers/s. When compared to the shape of the pure SCN interface, the alloy interface forms closer to the cold zone, indicating that the melting temperature decreased due to the alloying element. Extensive temperature measurements were performed on the outside of the ampoule containing pure SCN. The resulting thermal profiles are presented in detail in the results section. It is intended that the interface shape, thermal boundary condition and velocity data presented in this paper be used to test numerical simulations.

Simpson, James E.↗
NASA NTRS2000

Directional Solidification of Pure Succinonitrile and a Succinonitrile-Acetone Alloy

An experimental study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol% acetone alloy (SCN-1.0 mol.% ACE) has been performed. Experiments involving both a stationary thermal field (no-growth case) and a translating thermal field (growth case) were conducted. Growth rates of 2 and 40 micrometers/sec were investigated. For the pure SCN experiments, the velocity field in the melt was estimated using video images of seed particles in the melt. Observations of the seed particles indicate that a primary longitudinal convective cell is formed. The maximum velocity of two different particles which traveled along similar paths was the same and equal to 1.49 +/- 0.01 mm/s. The general accuracy of velocity measurements is estimated to be +/-0.08 mm/s, though the data shows consistency to within +/- 0.02 mm/s. The shape of the solid/liquid interface was also quantitatively determined. The solid/liquid interface was stable (non-dendritic and non-cellular) but not flat: rather it was significantly distorted by the influence of connection in the melt and, for the growth case, by the moving temperature boundary conditions along the ampoule. It was found that the interface shape and position were highly dependent on the alignment of the ampoule in the apparatus. Consequently, the ampoule was carefully aligned for all experiments. The values for front location agree with those determined in previous experiments. For the alloy experiments, the solid/liquid interface was determined to be unstable at growth rates greater than 2.8 micrometers/sec, but stable for the cases of no-growth and growth at 2 micrometers/sec. When compared to the shape of the pure SCN interface, the alloy interface forms closer to the cold zone, indicating that the melting temperature decreased due to the alloying element. Extensive temperature measurements were performed on the outside of the ampoule containing pure SCN. The resulting thermal profiles are presented in detail in the results section. It is intended that the interface shape, thermal boundary condition, and velocity data presented in this paper be used to test numerical simulations.

Simpson, James E.↗
NASA NTRS2012

The Near-Earth Encounter of Asteroid 308635 (2005 YU55): Thermal IR Observations

The near-Earth approach (0.00217 AU, or 0.845 lunar distances) of the C-type asteroid 308635 (2005 YU55) in November 2011 presented a rare opportunity for detailed observations of a low-albedo NEA in this size range. As part of a multi-telescope campaign to measure visible and infrared spectra and photometry, we obtained mid-infrared (approx. 8 to 22 micron) photometry and spectroscopy of 2005 YU55 using Michelle on the Gemini North telescope on UT November 9 and 10,2011. An extensive radar campaign together with optical light-curves established the rotation state of YU55. In addition, the radar imaging resulted in a shape model for the asteroid, detection of numerous boulders on its surface, and a preliminary estimate of its equatorial diameter at 380 +/- 20 m. In a preliminary analysis, applying the radar and lightcurve-derived parameters to a rough-surface thermophysical model fit to the Gemini/Michelle thermal emission photometry results in a thermal inertia range of approximately 500 to 1500 J/sq m/0.5s/K, with the low-thermal-inertia solution corresponding to the small end of the radar size range and vice versa. Updates to these results will be presented and modeling of the thermal contribution to the measured near-infrared spectra from Palomar/Triplespec and IRTF/SpeX will also be discussed.

Lim, Lucy F.↗
NASA NTRS2015

Measurement of Flaw Size From Thermographic Data

Simple methods for reducing the pulsed thermographic responses of delaminations tend to overestimate the size of the delamination, since the heat diffuses in the plane parallel to the surface. The result is a temperature profile over the delamination which is larger than the delamination size. A variational approach is presented for reducing the thermographic data to produce an estimated size for a flaw that is much closer to the true size of the delamination. The method is based on an estimate for the thermal response that is a convolution of a Gaussian kernel with the shape of the flaw. The size is determined from both the temporal and spatial thermal response of the exterior surface above the delamination and constraints on the length of the contour surrounding the delamination. Examples of the application of the technique to simulation and experimental data are presented to investigate the limitations of the technique.

Winfree, William P.↗
NASA NTRSDate not supplied

Mass Estimation Relationships for Conceptual Design of Blended-Wing-Body Cabin with Advanced Structures

Blended-Wing-Body (BWB) achieve a higher L/D than conventional tube and wing aircraft due to aerodynamic shaping of the non-circular pressure vessel that is made feasible through advanced composite technologies such as Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS). Due to the relatively new nature of the BWB, sufficient historical data does not exist for conceptual aircraft designers to base their structural weight estimations on, especially for estimating weights of the pressurized cabin center body. This paper describes general parametric Mass Estimation Relationships (MERs) based on high fidelity finite element analysis using PRSEUS for estimating the weight of a BWB pressurized cabin structure that includes cabin area, center body sweep, fineness ratio, and take-off gross weight.

BWB↗