Search NASA⌕ Search

SEARCH · Search NASA

Results for “solar materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Toward a tunable fabrication of multifunctional iron-aluminum spinels via solution combustion synthesis: The effects of fuel, heating mode, and Fe:Al precursor ratio

The solid solutions of iron and aluminum spinels (hercynite, maghemite, magnetite, and γ-alumina) are promising materials for emerging technologies such as solar thermochemical fuel production and clean dehydrogenation of fossil fuels. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of these materials as it has been used for synthesis of many nanoscale oxides. However, the design space of SCS is large with many synthesis parameters affecting the properties of the combustion products. To optimize the SCS of these materials, it is important to determine which parameters yield the best properties. In the present work, FeAlO x nanocomposites were obtained by SCS using iron nitrate and aluminum nitrate as precursors and oxidizers. Two fuels (citric acid and glycine), three Fe:Al molar ratios (1:2, 1:1, and 2:1) in the precursors, and three heating modes (hotplate, muffle furnace, and microwave oven) were compared. The products were characterized by X-ray diffraction analysis, scanning electron microscopy, Brunauer-Emmett-Teller surface area analysis, and laser diffraction particle size analysis. The fuel used had the largest impact on the combustion behavior and hence the material properties. The high combustion temperature of glycine allowed for the formation of an FeAl 2 O 4 /Fe 3 O 4 solid solution, while the lower-temperature combustion of citric acid yielded Al-substituted γ-Fe 2 O 3 with high amorphous content. With citric acid, the specific surface area as high as 200 m 2 /g was achieved. The effect of Fe:Al precursor ratio was clearly seen in variations of the lattice parameter, which demonstrated the ability to tune the phase composition. The heating mode had minor effects on material properties, but some differences were observed. As a result, all products obtained by SCS in a microwave oven had low specific surface areas compared to those obtained with a hotplate and a muffle furnace.

Alumina↗
DOE OSTI2024

“Green” Fabrication of High-performance Transparent Conducting Electrodes by Blade Coating and Photonic Curing on PET for Perovskite Solar Cells

This study presents an innovative material processing approach to fabricate transparent conducting electrodes (TCEs) on polyethylene terephthalate (PET) substrates using blade coating and photonic curing. The hybrid TCEs consist of a multiscale Ag network, combining silver metal bus lines and nanowires, overcoated by an indium zinc oxide layer, and then photonically cured. Blade coating ensures film uniformity and thickness control over large areas. Photonic curing, a non-thermal processing method with significantly lower carbon emissions, enhances the conductivity and transparency of the coated layers. Our hybrid TCEs achieve an average transmittance of (81 ± 0.4)% referenced to air ((90 ± 0.4)% referenced to the PET substrate) in the visible range, an average sheet resistance of (11 ± 0.5) Ω sq−1, and an average surface roughness of (4.3 ± 0.4) nm. We benchmark these values against commercial PET/TCE substrates. Mechanical durability tests demonstrate <3% change in resistance after 2000 bending cycles at a 1 in radius. The scalable potential of the hybrid TCE fabrication method is demonstrated by high uniformity and excellent properties in 7 in × 8 in large-area samples and by performing the photonic curing process at 11 m min−1. Furthermore, halide perovskite solar cells fabricated on these hybrid TCEs achieve average and champion power conversion efficiencies of (10.5 ± 1.0) % and 12.2%, respectively, and significantly outperform devices made on commercial PET/TCEs. This work showcases our approach as a viable pathway for high-speed “green” manufacturing of high-performance TCEs on PET substrates for flexible optoelectronic devices.

Bonner, Justin C↗
DOE OSTI2021

Influence of Ligand Structure on Excited State Surface Chemistry of Lead Sulfide Quantum Dots

The ligand-nanocrystal boundaries of colloidal quantum dots (QDs) mediate the primary energy and electron transfer processes that underpin photochemical and photocatalytic transformations at their surfaces. We use mid-infrared transient absorption spectroscopy to reveal the influence that ligand structure and bonding to nanocrystal surfaces have on the changes of the excited state surface chemistry of this boundary in PbS QDs and the corresponding impact on charge transfer processes between nanocrystals. We demonstrate that oleate ligands undergo marked changes in their bonding to surfaces in the excitonic excited states of the nanocrystals, indicating that oleate passivated PbS surfaces undergo significant structural changes following photoexcitation. These changes can impact the surface mobility of the ligands and the ability of redox shuttles to approach the nanocrystal surfaces to undergo charge transfer in photocatalytic reactions. In contrast, markedly different transient vibrational features are observed in iodide/mercaptoproprionic acid passivated PbS QD films that result from charge transfer between neighboring nanocrystals and localization of holes at the nanocrystal surfaces near MPA ligands. This ability to distinguish the influence that excitonic excited states vs charge transfer processes have on the surface chemistry of the ligand-nanocrystal boundary lays the groundwork for exploration of how this boundary can be understood and controlled for the design of nanocrystalline materials tailored for specific applications in solar energy harvesting and photocatalytic reactions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA‐Free, Phase‐Pure, and Stable α‐Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

Abstract α‐Formamidinium lead iodide (α‐FAPbI 3 ) is one of the most promising candidate materials for high‐efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of α‐FAPbI 3 where both the composition and the phase are pure is very challenging. Herein, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)‐free and phase‐pure stable α‐FAPbI 3 films. The incorporation of volatile FA‐based additives in the precursor solutions completely suppresses the formation of non‐perovskite δ‐FAPbI 3 during film crystallization. Grains of the desired α‐phase are anchored together and stabilized when 4‐ tert ‐butylbenzylammonium iodide is permeated into the α‐FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21 % for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ≈90 % of their initial efficiency after storage at 50 °C for over 1600 hours.

Ling, Xufeng↗
DOE OSTI2022

Simultaneously Enhancing Exciton/Charge Transport in Organic Solar Cells by an Organoboron Additive

Efficient exciton diffusion and charge transport play a vital role in advancing the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, a facile strategy is presented to simultaneously enhance exciton/charge transport of the widely studied PM6:Y6-based OSCs by employing highly emissive trans-bis(dimesitylboron)stilbene (BBS) as a solid additive. BBS transforms the emissive sites from a more H-type aggregate into a more J-type aggregate, which benefits the resonance energy transfer for PM6 exciton diffusion and energy transfer from PM6 to Y6. Transient gated photoluminescence spectroscopy measurements indicate that addition of BBS improves the exciton diffusion coefficient of PM6 and the dissociation of PM6 excitons in the PM6:Y6:BBS film. Transient absorption spectroscopy measurements confirm faster charge generation in PM6:Y6:BBS. Moreover, BBS helps improve Y6 crystallization, and current-sensing atomic force microscopy characterization reveals an improved charge-carrier diffusion length in PM6:Y6:BBS. Finally, owing to the enhanced exciton diffusion, exciton dissociation, charge generation, and charge transport, as well as reduced charge recombination and energy loss, a higher PCE of 17.6% with simultaneously improved open-circuit voltage, short-circuit current density, and fill factor is achieved for the PM6:Y6:BBS devices compared to the devices without BBS (16.2%).

14 SOLAR ENERGY↗
DOE OSTI2020

Vacuum-Free, All-Solution, and All-Air Processed Organic Photovoltaics with over 11% Efficiency and Promoted Stability Using Layer-by-Layer Codoped Polymeric Electrodes

Nonfullerene organic photovoltaics (OPVs) have achieved a breakthrough in pushing the efficiency beyond 15%. Although this sheds light on OPV commercialization, the high cost associated with the scalable device fabrications remains a giant challenge. Herein, a vacuum-free, all-solution and all-air processed OPV is reported that yields 11.12% efficiency with a fill factor of 0.725, due to the usages of high-merit polymeric electrodes and modified active blends. The design principle toward the high-merit electrodes is to induce heavy acid doping into the matrices for a raised carrier concentration and mobility, make a large removal of insulating components in the whole matrices rather than surfaces, and restrain the formation of large-domain aggregates. A unique layer-by-layer doping is developed to enable the polymeric electrodes with record-high trade-offs between optical transmittance and electrical conductivity. Moreover, solvent vapor annealing is proposed to boost device efficiency and it has the advantages of finely adjusting the active blend morphology and raising the electron mobility. The resulting devices are highly efficient and most (≈91%) of the initial efficiency are maintained in 30 day storage. Finally, this work indicates bright future for making cost-effective all-solution processed OPVs in air.

14 SOLAR ENERGY↗
DOE OSTI2021

On-device lead absorbing tapes for sustainable perovskite solar cells

Perovskite solar cells are a promising technology that could facilitate and accelerate the energy transition to a sustainable future. However, the toxicity of Pb remains one of the obstacles impeding their commercialization. Here we apply on-device tapes to absorb leaked lead from damaged devices. Furthermore, our chemical approach can capture over 99.9% of leakage without compromising the performance and operation.

14 SOLAR ENERGY↗
DOE OSTI2021

Phonon-Assisted Ballistic Current from First-Principles Calculations

The bulk photovoltaic effect (BPVE) refers to current generation due to illumination by light in a homogeneous bulk material lacking inversion symmetry. In addition to the intensively studied shift current, the ballistic current, which originates from asymmetric carrier generation due to scattering processes, also constitutes an important contribution to the overall kinetic model of the BPVE. In this Letter, we use a perturbative approach to derive a formula for the ballistic current resulting from the intrinsic electron-phonon scattering in a form amenable to first-principles calculation. We then implement the theory and calculate the ballistic current of the prototypical BPVE material BaTiO 3 using quantum-mechanical density functional theory. The magnitude of the ballistic current is comparable to that of the shift current, and the total spectrum (shift plus ballistic) agrees well with the experimentally measured photocurrents. Furthermore, we show that the ballistic current is sensitive to structural change, which could benefit future photovoltaic materials design.

14 SOLAR ENERGY↗
DOE OSTI2019

Point defects, compositional fluctuations, and secondary phases in non-stoichiometric kesterites

The efficiency of kesterite-based solar cells is limited by various non-ideal recombination paths, amongst other by a high density of defect states and by the presence of binary or ternary secondary phases within the absorber layer. Pronounced compositional variations and secondary phase segregations are indeed typical features of non-stoichiometric kesterite materials. Certainly kesterite-based thin film solar cells with an off-stoichiometric absorber layer composition, especially Cu-poor/Zn-rich, achieved the highest efficiencies, but deviations from the stoichiometric composition lead to the formation of intrinsic point defects (vacancies, anti-sites, and interstitials) in the kesterite-type material. In addition, a non-stoichiometric composition is usually associated with the formation of undesirable side-phase (secondary phases). Thus the correlation between off-stoichiometry and intrinsic point defects as well as the identification and quantification of secondary phases and compositional fluctuations in non-stoichiometric kesterite materials is of great importance for the understanding and rational design of solar cell devices. Here, this paper summarizes the latest achievements in the investigation of identification and quantification of intrinsic point defects, compositional fluctuations and secondary phases in non-stoichiometric kesterite-type materials.

14 SOLAR ENERGY↗
DOE OSTI2022

Physiochemical Machine Learning Models Predict Operational Lifetimes of CH3NH3PbI3 Perovskite Solar Cells

Halide perovskites are promising photovoltaic (PV) materials with the potential to lower the cost of electricity and greatly expand the penetration of PV if they can demonstrate long-term stability under illumination in the presence of moisture and oxygen. The solar cell service lifetime as quantified by the T80 (the time required for the power conversion efficiency to drop to 80% of its starting value) is a useful metric to assess stability. The T80 for utility, commercial, or residential PV systems needs to be several decades in order to yield low-cost electricity, and thus it is not practical to directly measure the T80. It would be useful if T80 could be predicted from the initial dynamics of a solar cell’s performance, but until now no models have been developed to forecast T80. In this work, we report the development of machine learning models to predict T80 of ITO/NiOx/CH3NH3PbI3/C60/BCP/Ag solar cells operating at maximum power point under 1-sun equivalent photon flux in air at varying temperatures and relative humidities. Efficiency losses are driven by short-circuit current and fill factor, indicating that chemical decomposition of the perovskite is a major contributor to degradation. Spatial patterns evident from in situ dark field optical microscopy suggest that the electric field gradient at device edges plays a significant role in perovskite decomposition, along with photochemical reactions with O2 and H2O. Models are trained using a menu of features from three distinct categories: (i) features based on measurements of the initial rates of change of device parameters, (ii) features based on the ambient conditions during operation (temperature, & partial pressure of H2O), and (iii) features based on underlying physics and chemistry. We show that a theory-based physiochemical feature derived from a model of the chemical reaction kinetics of the rate of degradation of the CH3NH3PbI3 is particularly valuable for prediction. This physiochemical feature was selected as the first or second most dominant feature in the best performing models. With a dataset consisting of 45 accelerated degradation experiments with T80 that range over a factor of 30, the model predicts T80 with an accuracy of about 40% (|predicted T80 - observed T80| / observed T80) on samples not used in training. This hybrid ML approach should be effective when applied to other compositions, device architectures, and advanced packaging schemes.

14 SOLAR ENERGY↗
DOE OSTI2022

Physiochemical Machine Learning Models Predict Operational Lifetimes of CH3NH3PbI3 Perovskite Solar Cells

Halide perovskites are promising photovoltaic (PV) materials with the potential to lower the cost of electricity and greatly expand the penetration of PV if they can demonstrate long-term stability under illumination in the presence of moisture and oxygen. The solar cell service lifetime as quantified by the T80 (the time required for the power conversion efficiency to drop to 80% of its starting value) is a useful metric to assess stability. The T80 for utility, commercial, or residential PV systems needs to be several decades in order to yield low-cost electricity, and thus it is not practical to directly measure the T80. It would be useful if T80 could be predicted from the initial dynamics of a solar cell’s performance, but until now no models have been developed to forecast T80. In this work, we report the development of machine learning models to predict T80 of ITO/NiOx/CH3NH3PbI3/C60/BCP/Ag solar cells operating at maximum power point under 1-sun equivalent photon flux in air at varying temperatures and relative humidities. Efficiency losses are driven by short-circuit current and fill factor, indicating that chemical decomposition of the perovskite is a major contributor to degradation. Spatial patterns evident from in situ dark field optical microscopy suggest that the electric field gradient at device edges plays a significant role in perovskite decomposition, along with photochemical reactions with O2 and H2O. Models are trained using a menu of features from three distinct categories: (i) features based on measurements of the initial rates of change of device parameters, (ii) features based on the ambient conditions during operation (temperature, & partial pressure of H2O), and (iii) features based on underlying physics and chemistry. We show that a theory-based physiochemical feature derived from a model of the chemical reaction kinetics of the rate of degradation of the CH3NH3PbI3 is particularly valuable for prediction. This physiochemical feature was selected as the first or second most dominant feature in the best performing models. With a dataset consisting of 45 accelerated degradation experiments with T80 that range over a factor of 30, the model predicts T80 with an accuracy of about 40% (|predicted T80 - observed T80| / observed T80) on samples not used in training. This hybrid ML approach should be effective when applied to other compositions, device architectures, and advanced packaging schemes.

14 SOLAR ENERGY↗
DOE OSTI2023

Small to Large Polaron Behavior Induced by Controlled Interactions in Perovskite Quantum Dot Solids

The polaron is an essential photoexcitation that governs the unique optoelectronic properties of organic–inorganic hybrid halide perovskites, and it has been subject to extensive spectroscopic and theoretical investigation over the past decade. A crucial but underexplored question is how the nature of the photogenerated polarons is impacted by the microscopic perovskite structure and what functional properties this affects. To tackle this question, we chemically tuned the interactions between perovskite quantum dots (QDs) to rationally manipulate the polaron properties. Through a suite of time-resolved spectroscopies, we find that inter-QD interactions open an excited-state channel to form large polaron species, which exhibit enhanced spatial diffusion, slower hot polaron cooling, and a longer intrinsic lifetime. At the same time, polaronic excitons are formed in competition via localized band-edge states, exhibiting strong photoluminescence but are limited by shorter intrinsic lifetimes. Furthermore, this control of polaron type and function through tunable inter-QD interactions not only provides design principles for QD-based materials but also experimentally disentangles polaronic species in hybrid perovskite materials.

14 SOLAR ENERGY↗
DOE OSTI2022

Perovskite- and Dye-Sensitized Solar-Cell Device Databases Auto-generated Using ChemDataExtractor

The number of scientific publications reporting cutting-edge third-generation photovoltaic devices is increasing rapidly, owing to the pressing need to develop renewable-energy technologies that address the climate-change crisis. Consequently, the field could benefit from a central repository where photovoltaic-performance metrics, such as the power-conversion efficiency (η) are recorded. We present two automatically generated databases that contain photovoltaic properties and device material data for dye-sensitized solar cells (DSCs) and perovskite solar cells (PSCs), totalling 660,881 data entries representing 57,678 photovoltaic devices. The databases were generated by applying the text-mining toolkit ChemDataExtractor on a corpus of 25,720 articles. A multi-faceted evaluation, incorporating manual and automatic methods, was applied to ensure that the data contained therein were of the highest quality, with precision metrics ranging from 73.1% to 95.8%. The DSC database contains 475,045 entries representing 41,680 devices, and the PSC database contains 185,836 entries representing 15,818 devices. The databases are available in MongoDB and JSON formats, which can be queried in Python, R, Java and MATLAB for data-driven photovoltaic materials discovery.

14 SOLAR ENERGY↗
DOE OSTI2023

19.28% Efficiency and Stable Polymer Solar Cells Enabled by Introducing an NIR–Absorbing Guest Acceptor

Here, a near-infrared (NIR)-absorbing small-molecule acceptor (SMA) Y-SeNF with strong intermolecular interaction and crystallinity is developed by combining selenophene-fused core with naphthalene-containing end-group, and then as a custom-tailor guest acceptor is incorporated into the binary PM6:L8-BO host system. Y-SeNF shows a 65 nm red-shifted absorption compared to L8-BO. Thanks to the strong crystallinity and intermolecular interaction of Y-SeNF, the morphology of PM6:L8-BO:Y-SeNF can be precisely regulated by introducing Y-SeNF, achieving improved charge-transporting and suppressed non-radiative energy loss. Consequently, ternary polymer solar cells (PSCs) offer an impressive device efficiency of 19.28% with both high photovoltage (0.873 V) and photocurrent (27.88 mA cm –2 ), which is one of the highest efficiencies in reported single-junction PSCs. Notably, ternary PSC has excellent stability under maximum-power-point tracking for even over 200 h, which is better than its parental binary devices. The study provides a novel strategy to construct NIR-absorbing SMA for efficient and stable PSCs toward practical applications.

14 SOLAR ENERGY↗
DOE OSTI2020

Growth and Characterization of Arsenic-Doped CdTe 1-x Se x Single Crystals Grown by the Cd-Solvent Traveling Heater Method

The photovoltaic performance of CdTe solar cells is mainly limited by low doping and short minority carrier lifetime. Group-V element doping and Se-alloying have a significant impact on tuning these fundamental CdTe properties. In this paper, we report the growth of p-type As-doped, Cd-rich CdTe 1-x Se x single crystals using metallic Cd as the solvent in the traveling-heater method. The structural and electrical properties of CdTe1-xSex are examined for different Se concentrations. CdTe 1-x Se x single crystals (0 ≤ x ≤ 0.5) with zincblende structure indicate homogeneous composition. The 10 17 cm-3 As-doping activation efficiency can be maintained at close to 50% for x ≤ 0.2. Se alloying leads to bulk minority carrier lifetime exceeding 30 ns for samples doped near 1017 cm -3 . These results help us to overcome the current roadblocks in device performance.

14 SOLAR ENERGY↗