Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Effects of surface chemistry on hot corrosion life

Burner rig tests were conducted under the following conditions: 900 C, hourly thermal cycling, 0.5 ppm sodium as MaCl in the gas stream, velocity 0.3 Mach. The alloys are Udiment 700, Rene 80, uncoated and with RT21, Codep, or NiCoCrAlY coatings. These tests were completed for specimens in the as-processed condition and after aging at 1100 C in oxidizing or inert evnivronments for time up to 600 hours. Coil inductance changes used for periodic nondestructive inspection of specimens were useful in following the course of corrosion. Typical sulfidation was observed in all cases, structurally similar to that observed for service-run turbine components. Aging at cuased a severe decrease in hot corrosion life of RT21 and Codep coatings and a significant but less decrease in the life of the NiCoCrAlY coating. The extent of these decreases was much greater for all three coatings on U700 substrates than on Rene 80 substrates. Coating/substrate interdiffusion rather than by surface oxidation.

Fryxell, R. E.↗
NASA NTRS1985

The effects of surface pretreatment and nitrogen tetroxide purification on the corrosion rate of Type 304L stainless steel

Corrosion rates of 304L stainless steel coupons in MON-1 oxidizer have been measured as a function of cleaning procedures employed, surface layer positions, propellant impurity levels, and short-term exposure durations (14 to 90 days). Of special interest was propellant contamination by buildup of soluble iron, which may cause flow decay. Surface treatments employed were combinations of cleaning, pickling, and passivation procedures. Propellants used were MIL-SPEC MON-1 and several types of purified NTO (i.e., low water, low chloride) which may, at a later time, be specified as spacecraft grade. Pretest coupon surface analysis by X-ray photoelectron spectroscopy (XPS-ESCA) has revealed important differences, for the different cleaning procedures, in the make-up of the surface layer, both in composition and state of chemical combination of the elements involved. Comparisons will be made of XPS/ESCA data, for different cleaning procedures, for specimens before and after propellant exposure.

Blue, G. D.↗
NASA NTRS1986

Effects of surface chemistry on hot corrosion life

Burner rig tests were conducted under the following conditions: 900 C, hourly thermal cycling, 0.5 ppm sodium as NaCl in the gas stream, and Mach 0.3 velocity. The alloys tested were Udimet 700 (U700) and Rene 80, uncoated and with RT21, Codep, or NiCoCrAlY coatings. The tests, up to 1000 hours, included specimens in the as-processed condition and after aging at 1100 C in oxidizing or inert environments for up to 600 hours. Coil-inductance changes were measured for periodic nondestructive inspection of speciments and found useful in the following course of corrosion. Typical sulfidation observed in all cases was similar to that observed in service-run turbine components. Aging at 1100 C caused severe decrease in the hot corrosion life of RT21 and Codep coatings and a significant but lesser decrease in the life of NiCoCrAlY coatings. The extent of these decreases was much greater for all three coatings on U700 than on Rene substrates. A coating hot corrosion life-predicitin model was proposed. The model requires time/temperature information for a turbine component at takeoff conditions as well as environmental contaminant information.

Fryxell, R. E.↗
NASA NTRS1986

Effect of surface ionization on wetting layers

A surface ionization model due to Langmuir is generalized to liquid mixtures of polar and nonpolar components in contact with ionizable substrates. When a predominantly nonpolar mixture is near a miscibility gap, thick wetting layers of the conjugate polar phase form on the substrate. Such charged layers can be much thicker than similar wetting layers stabilized by dispersion forces. This model may explain the 0.4- to 0.6-micron-thick wetting layers formed in stirred mixtures of nitromethane and carbon disulfide in contact with glass.

Kayser, R. F.↗
NASA NTRS1984

Effects of surface chemistry on hot corrosion life

Hot corrosion life prediction methodology based on a combination of laboratory test data and field service turbine components, which show evidence of hot corrosion, were examined. Components were evaluated by optical metallography, scanning electron microscopy (SEM), and electron micropulse (EMP) examination.

Fryxell, R. E.↗
NASA NTRS1985

Effects of surface chemistry on hot corrosion life

This program has its primary objective: the development of hot corrosion life prediction methodology based on a combination of laboratory test data and evaluation of field service turbine components which show evidence of hot corrosion. The laboratory program comprises burner rig testing by TRW. A summary of results is given for two series of burner rig tests. The life prediction methodology parameters to be appraised in a final campaign of burner rig tests are outlined.

Fryxell, R. E.↗
NASA NTRS1988

Effect of surface tension on the dynamical behavior of bubble in rotating fluids under low gravity environment

Time dependent evolutions of the profile of free surface (bubble shapes) for a cylindrical container partially filled with a Newtonian fluid of constant density, rotating about its axis of symmetry, have been studied. Numerical computations of the dynamics of bubble shapes have been carried out with the following situations: (1) linear functions of spin-up and spin-down in low and microgravity environments, (2) linear functions of increasing and decreasing gravity enviroment in high and low rotating cylidner speeds, (3) step functions of spin-up and spin-down in a low gravity environment, and (4) sinusoidal function oscillation of gravity environment in high and low rotating cylinder speeds. The initial condition of bubble profiles was adopted from the steady-state formulations in which the computer algorithms have been developed by Hung and Leslie (1988), and Hung et al. (1988).

Hung, R. J.↗
NASA NTRS1989

The effects of surface films on mechanical behavior of B2 ordered intermetallic alloys

Surface films deposited on body-centered cubic metals can greatly reduce the yield and flow stresses and increase the ductility at low homologous temperatures. This softening process is associated with the ability of the film-substrate interface to generate large populations of mobile edge dislocations. This phenomenon is extended to B2 ordered intermetallic alloys, which display many deformation characteristics of bcc metals. Single crystal NiAl coated with thermally formed oxide films and polycrystalline FeAl with electrochemically formed Fe-Al-O films display film softening at and below room temperature. The extent of film softening is shown to depend on many factors, including crystal orientation, deformation temperature, operative slip systems, film thickness, film adherence, and film and substrate properties.

Noebe, R. D.↗
NASA NTRS1991

An investigation of the effect of surface impurities on the adsorption kinetics of hydrogen chemisorbed onto iron

The goal was to develop an understanding of heterogeneous kinetic processes for those molecular species which produce gaseous hydrogen degradation of the mechanical properties of metallic structural materials. Although hydrogen degradation of metallic materials is believed to result from dissolved protonic hydrogen, the heterogeneous hydrogen interface transport processes often dominate the kinetics of the degradation process. The initial step in the interface transport process is the dissociative chemisorption of the molecular species at the metal surface followed by hydrogen absorption into and transport through the bulk. Modern advanced aerospace applications often require the use of structural materials in high pressure hydrogen environments at temperatures which range from low cryogenic temperatures to very high temperatures (1300 K and greater). Materials proposed for these applications, such as the titanium aluminides, beta-titanium alloys, nickel- and cobalt-based superalloys, molybdenum-rhenium alloys, beryllium, and various beryllides, need to possess a high degree of immunity from hydrogen induced degradation of mechanical properties. In the present program, the interaction of hydrogen with the surfaces of alpha-2 (Ti3Al) titanium aluminide, gamma (TiAl) titanium aluminide, and beryllium were studied. The interaction of low pressure hydrogen with gamma titanium aluminide and beryllium was found to be relatively weak, in the sense that adsorption leads to a low surface concentration of dissociated hydrogen, i.e., the chemisorption process is reversible at room temperature (300 K) for gamma titanium aluminide and the sticking coefficient for chemisorption is extremely small for beryllium. Hydrogen was found to interact readily with alpha-2 titanium aluminide to form a stable surface hydride at 300 K. These results correlate well with other recent studies which show that the mechanical properties for alpha-2 titanium aluminide are readily degraded in hydrogen while gamma titanium aluminide exhibits less degradation and beryllium essentially no degradation. The interaction of oxygen with the surface of these materials has been studied, also, in the present program.

Shanabarger, Mickey R.↗
NASA NTRS1992

Effect of surface condition on the formation of solid lubricating films at high temperatures

Solid films were produced on active metal or ceramic surfaces using lubricants (such as tricresyl phosphate) delivered as a vapor at high temperatures, and the lubricity of these deposits under different dynamic wear conditions was investigated. A method is described for chemically activating ceramic surfaces resulting in a surface that could promote the formation of lubricating polymeric derivative of TCP. Experiments were carried out to evaluate the wear characteristics of unlubricated cast iron and of Sialon ceramic at 25 and 280 C, and lubricated with a vapor of TCP at 280 C. It is shown that continuous vapor phase lubrication of chemically treated Sialon reduced its coefficient of friction from 0.7 to less than 0.1.

Hanyaloglu, Bengi↗
NASA NTRS1992

The effect of surface roughness on Triton's volatile distribution

Calculations of radiative equilibrium temperatures on Triton's rough surface suggest that significant condensation of N2 may be occurring in the northern equatorial regions, despite their relatively dark appearance. The bright frost is not apparent in the Voyager images because it tends to be concentrated in relatively unilluminated facets of the surface. This patchwork of bright frost-covered regions and darker bare ground may be distributed on scales smaller than that of the Voyager resolution; as a result the northern equatorial regions may appear relatively dark. This hypothesis also accounts for the observed wind direction in the Southern Hemisphere because it implies that the equatorial regions are warmer than the south polar regions.

Yelle, Roger V.↗
NASA NTRS1992

Measurements of the effects of surface winds on ocean currents with a stepped-frequency Alpha K radar system

A frequency-agile C band Alpha K radar system was used to measure ocean surface currents during the SAXON-Chesapeake Light Tower experiment. Surface currents were measured with the radar approximately 80 percent of the time from September 20 to October 14, 1988. These measurements are compared with in situ current and wind probe measurements. The agreement between the radar and current probe measurements are found to be very good during periods when the wind- and wave-driven currents are negligible in the radar-viewing direction. During other times, the radar measurements are approximated by the Weber model.

Popstefanija, Ivan↗