Results for “vibration data” — Page 27

DOE OSTI2023

Complete collision data set for electrons scattering on molecular hydrogen and its isotopologues: IV. Vibrationally-resolved ionization of the ground and excited electronic states

Here, we present a comprehensive set of vibrationally-resolved cross sections for electron-impact ionization of molecular hydrogen and its isotopologues (H 2 , D 2 , T 2 , HD, HT, and DT) in both the ground and excited electronic states. We apply the adiabatic-nuclei molecular convergent close-coupling (MCCC) method to calculate cross sections from threshold to 1000 eV for ionization of the ground and excited vibrational levels of the X 1 Σ$^{+}_{g}$, B 1 Σ$^{+}_{u}$, C 1 π u , EF 1 Σ$^{+}_{g}$, a 3 Σ$^{+}_{g}$, and c 3 π u electronic states, representing all states with united-atoms-limit principle quantum number n=1–2. The cross sections are presented in graphical form and provided as both numerical values and analytic fit functions in supplementary data files. The data can also be downloaded from the MCCC database at mccc-db.org.

74 ATOMIC AND MOLECULAR PHYSICS↗

NASA NTRS1984

Investigation of the external flow analysis for density measurements at high altitude

The results of analysis performed on the external flow around the shuttle orbiter nose regions at the Shuttle Upper Atmosphere Mass Spectrometer (SUMS) inlet orifice are presented. The purpose of the analysis is to quantitatively characterize the flow conditions to facilitate SUMS flight data reduction and subsequent determination of orbiter aerodynamic force coefficients in the hypersonic rarefied flow regime. Experimental determination of aerodynamic force coefficients requires accurate simultaneous measurement of forces (or acceleration) and dynamic pressure along with independent knowledge of density and velocity. The SUMS provides independent measurement of dynamic pressure; however, it does so indirectly and requires knowledge of the relationship between measured orifice conditions and the dynamic pressure which can only be determined on the basis of molecule or theory for a winged configuration. Monte Carlo direct simulation computer codes were developed for both the flow field solution at the orifice and for the internal orifice flow. These codes were used to study issues associated with geometric modeling of the orbiter nose geometry and the modeling of intermolecular collisions including rotational energy exchange and a preliminary analysis of vibrational excitation and dissociation effects. Data obtained from preliminary simulation runs are presented.

Bienkowski, G. K.↗

NASA NTRSDate not supplied

Expanding Repository Data Available For Sharing and Knowledge Discovery

Some of the hardest space biology and space health challenges require data-intensive, bioinformatic, meta-analytical, and computer-assisted research approaches. These challenges include examining interdisciplinary space life science research across experiments and across interacting spaceflight hazards (radiation, altered gravity, confinement, hostile-closed environments, distance-duration from Earth). The approaches to confront these challenges involve mining multiple datasets simultaneously from various hierarchical organizations of biological complexity, all while concurrently evaluating how experimental design factors affect endpoints of standard assays. To enable this field, it is essential that principal investigators (PIs) submit data in a structure so it can be maximally re-used. The purpose of the NASA Ames Life Sciences Data Archive (ALSDA) is to collect, curate, and make publicly available all non-human space-relevant biological data. ALSDA must also ensure data are open-access, and maximally findable, accessible, interoperable, and reusable (FAIR). The scope of ALSDA data collected and submitted by PIs include subject and study design metadata, assay metadata parameters, raw and processed assay data, assay imagery/video, and subject-experienced mission data telemetry (radiation, temperature, humidity, acoustics, vibrations, etc.). ALSDA recently integrated into a collaborative group of Open Science projects to facilitate a suite of new tools and workflows that will improve data submission, accessibility, and reusability by implementing digital data submission agreements, and adopting the data management system originally developed by NASA GeneLab. ALSDA intends to bring current biological repository data and all future collected data into this new scientific data reuse reality. This new suite of tools will enable ALSDA to deploy a science curation system using scientific assay configurations for the data submission portal. It will capture essential assay parameters according to established standards in each sub-field within biology. The submission portal expedites data collection by enhancing ease of PI data submission, providing a user interface and specificity for which data is to be submitted. Data submissions can be brought into cutting-edge informatic analysis portals to enable mining of physiological, behavioral, biochemical, and imaging datasets in conjunction with ‘omics-level datasets. As ALSDA datasets are submitted, curated, and published (e.g., micro-computed tomography, histology, pulse oximetry, serum metabolites, magnetic resonance imaging, intraocular pressure, novel object recognition, etc.), the merging together of spaceflight data along this multi-hierarchical complexity of biology will enable informatics and data-intensive approaches resulting in knowledge discoveries across missions, space hazards, and biological disciplines.

Biology↗

NASA NTRSDate not supplied

Expanding Repository Data Available For Sharing And Knowledge Discovery

Some of the hardest space biology and space health challenges require data-intensive, bioinformatic, meta-analytical, and computer-assisted research approaches. These challenges include examining interdisciplinary space life science research across experiments and across interacting spaceflight hazards (radiation, altered gravity, confinement, hostile-closed environments, distance-duration from Earth). The approaches to confront these challenges involve mining multiple datasets simultaneously from various hierarchical organizations of biological complexity, all while concurrently evaluating how experimental design factors affect endpoints of standard assays. To enable this field, it is essential that principal investigators (PIs) submit data in a structure so it can be maximally re-used. The purpose of the NASA Ames Life Sciences Data Archive (ALSDA) is to collect, curate, and make publicly available all non-human space-relevant biological data. ALSDA must also ensure data are open-access, and maximally findable, accessible, interoperable, and reusable (FAIR). The scope of ALSDA data collected and submitted by PIs include subject and study design metadata, assay metadata parameters, raw and processed assay data, assay imagery/video, and subject-experienced mission data telemetry (radiation, temperature, humidity, acoustics, vibrations, etc.). ALSDA recently integrated into a collaborative group of Open Science projects to facilitate a suite of new tools and workflows that will improve data submission, accessibility, and reusability by implementing digital data submission agreements, and adopting the data management system originally developed by NASA GeneLab. ALSDA intends to bring current biological repository data and all future collected data into this new scientific data reuse reality. This new suite of tools will enable ALSDA to deploy a science curation system using scientific assay configurations for the data submission portal. It will capture essential assay parameters according to established standards in each sub-field within biology. The submission portal expedites data collection by enhancing ease of PI data submission, providing a user interface and specificity for which data is to be submitted. Data submissions can be brought into cutting-edge informatic analysis portals to enable mining of physiological, behavioral, biochemical, and imaging datasets in conjunction with ‘omics-level datasets. As ALSDA datasets are submitted, curated, and published (e.g., micro-computed tomography, histology, pulse oximetry, serum metabolites, magnetic resonance imaging, intraocular pressure, novel object recognition, etc.), the merging together of spaceflight data along this multi-hierarchical complexity of biology will enable informatics and data-intensive approaches resulting in knowledge discoveries across missions, space hazards, and biological disciplines.

life science↗

NASA NTRS1992

Densities and vibrational distribution of H(3+) in the Jovian auroral ionosphere

The assumption that H(3+) is in LTE in the region of the Jovian ionosphere from which the emissions originate is tested by calculating the vibrational distribution of H(3+) over the altitude range of 350 to 1500 km above the methane cloud tops. A model of the Jovian auroral ionosphere is constructed in which the neutral temperatures are enhanced over those of the midlatitude ionosphere, as suggested by observations and models of the auroral region. The energy and energy flux were found to be less than those involved in the production of the UV aurora. A computation of the densities and vibrational distribution shows that the distribution of the six lowest states of H(3+) can be determined fairly well in spite of uncertainties in the atomic and molecular data. The computed altitude profiles and vibrational distributions of H(3+) and H2 are consistent with the observations of IR emission in the 2- and 4-micron regions.

Kim, Y. H.↗

NASA NTRS1984

A rapid method for obtaining frequency-response functions for multiple input photogrammetric data

A two-digital-camera photogrammetric technique for measuring the motion of a vibrating spacecraft structure or wing surface and an applicable data-reduction algorithm are presented. The 3D frequency-response functions are obtained by coordinate transformation from averaged cross and autopower spectra derived from the 4D camera coordinates by Fourier transformation. Error sources are investigated analytically, and sample results are shown in graphs.

Kroen, M. L.↗

NASA NTRS1974

Skylab vibroacoustic test program

Vibroacoustic testing was performed on the orbital workshop dynamic test article and the payload assembly, the two major elements of the Skylab payload. The testing was conducted on each of the Skylab elements separately in the reverberation chamber at the Johnson Space Center. The two test configurations were high fidelity flight article simulations. The testing was conducted in two phases; in the first phase, acoustic tests were performed at levels simulating the lift-off and atmospheric flight acoustic criteria. In the second phase, low frequency sinusoidal vibration tests were conducted to obtain modal response data. The objectives of the Skylab vibroacoustic test program were to: verify the vibration design and test criteria; qualify selected flight components to the vibroacoustic criteria; and verify analytical models used for dynamic load analyses. This paper describes the vibroacoustic testing and discusses the results.

Jewell, R. E.↗

NASA NTRS1967

C-1 engine. Propellant valve qualification, volume 2, book 3 Final report

Vibration, shock, and acceptance test data for C-1 rocket engine propellant valve qualification

Mc Gall, J.↗

NASA NTRS1973

Method of study of the possibility of predicting the quality of treatment in polishing by vibroacoustical processes

The quality of vibroacoustical surface polishing and the deviation formation process of the surfaces were studied using a polishing mill unit. Data cover spectral composition of vibration accelerations and vibration displacements of individual elements, precision rotation of the polishing circle spindle in static and dynamic operation modes, spectral composition of relative vibrations of polishing circle and the part being processed, statistical and dynamic rigidity of individual elements, and APFC of the elastic system of the mill stand. The effect of individual spindle parameters on vibroacoustical characteristics of the system was also discussed as well as the spectrum measurement of the disturbing force.

Trubnikov, V. V.↗

NASA NTRS1976

Low-frequency noise reduction of lightweight airframe structures

The results of an experimental study to determine the noise attenuation characteristics of aircraft type fuselage structural panels were presented. Of particular interest was noise attenuation at low frequencies, below the fundamental resonances of the panels. All panels were flightweight structures for transport type aircraft in the 34,050 to 45,400 kg (75,000 to 100,000 pounds) gross weight range. Test data include the results of vibration and acoustic transmission loss tests on seven types of isotropic and orthotropically stiffened, flat and curved panels. The results show that stiffness controlled acoustically integrated structures can provide very high noise reductions at low frequencies without significantly affecting their high frequency noise reduction capabilities.

Getline, G. L.↗

NASA NTRS1985

Shuttle structural dynamics characteristics: The analysis and verification

The space shuttle introduced a new dimension in the complexity of the structural dynamics of a space vehicle. The four-body configuration exhibited structural frequencies as low as 2 hertz with a model density on the order of 10 modes per hertz. In the verification process, certain mode shapes and frequencies were identified by the users as more important than others and, as such, the test objectives were oriented toward experimentally extracting those modes and frequencies for analysis and test correlation purposes. To provide the necessary experimental data, a series of ground vibration tests (GVT's) was conducted using test articles ranging from the 1/4-scale structural replica of the space shuttle to the full-scale vehicle. The vibration test and analysis program revealed that the mode shapes and frequency correlations below 10 hertz were good. The quality of correlation of modes between 10 and 20 hertz ranged from good to fair and that of modes above 20 hertz ranged from poor to good. Since the most important modes, based on user preference, were below 10 hertz, it was judged that the shuttle structural dynamic models were adequate for flight certifications.

Modlin, C. T., Jr.↗

NASA NTRS1989

Comparison of predicted and measured temperatures of UH-60A helicopter transmission

The 2109-kW (2828-hp) UH-60A Black Hawk helicopter transmission was one of the transmissions used to obtain an experimental data base. Component improvements or new transmission concepts can thus be evaluated by comparison with the established data. Results of efficiency and vibration tests of the UH-60A have been reported previously. In this investigation the transmission was instrumented internally and tested over a range of operating conditions. The speed was varied from 50 to 100 percent of the full rated value, and the torque was varied from 10 to 100 percent of the full rated value. Temperatures of internal bearings and gears were measured. The computer program Planetsys was used to simulate the thermal performance of this transmission. The calculated temperatures were then compared with the corresponding measured values. The highest measured temperature was 405 K (270 F) on the outer race of the high-speed input shaft roller bearing, at the 100-percent power condition. In general, the predicted temperatures compared very well with the measured values, most of them being within 5 kelvin (9 F). Specifically, the temperatures predicted for the single-row spherical roller planetary bearing averaged only about 4 kelvin (8 F) lower than the highest measured value.

Coe, Harold H.↗

NASA NTRS1990

Space Station Freedom: Dynamic instrumentation for a large space structure

A proposed approach called Modal Identification Experiment (MIE) for obtaining on-orbit dynamic response measurements on Space Station Freedom, the first of a family of large, flexible space structures is discussed. The Phase 2 conceptual design study which provides a conceptual design of a proposed measurement system and an experimental protocol for inobstrusively collecting dynamic response data critical to characterizing important vibration modes of Space Station Freedom were recently concluded. The case for conducting such a measurement program is presented and the specific MIE objectives that were identified, are listed. The sequence of discrete Space Station Freedom assembly configurations is described, and the Phase 2 conceptual design of the experiment and instrumentation system are defined. In addition, a plan to utilize a space station hydrid scale model in laboratory simulations as part of the design process are discussed.

Raney, John P.↗

NASA NTRS1996

Torsional Buckling Tests of a Simulated Solar Array

Spacecraft solar arrays are typically large structures supported by long, thin deployable booms. As such, they may be particularly susceptible to abnormal structural behavior induced by mechanical and thermal loading. One example is the Hubble Space Telescope solar arrays which consist of two split tubes fit one inside the other called BiSTEMs. The original solar arrays on the Hubble Space Telescope were found to be severely twisted following deployment and later telemetry data showed the arrays were vibrating during daylight to night and night to daylight transition. The solar array twist however can force the BiSTEM booms to change in cross-section and cause tile solar arrays to react unpredictably to future loading. The solar arrays were redesigned to correct for tile vibration, however, upon redeployment they again twisted. To assess the influence of boom cross-sectional configuration, experiments were conducted on two types of booms, (1)booms with closed cross-sections, and (2) booms with open cross-sections. Both models were subjected to compressive loading and imposed tip deflections. An existing analytical model by Chung and Thornton was used to define the individual load ranges for each model solar array configuration. The load range for the model solar array using closed cross-section booms was 0-120 Newtons and 0-160 Newtons for the model solar array using open cross-section booms. The results indicate the model solar array with closed cross-section booms buckled only in flexure. However, the results of the experiment with open cross-section booms indicate the model solar array buckled only in torsion and with imposed tip deflections the cross section can degrade by rotation of the inner relative to the outer STEM. For tile Hubble Space Telescope solar arrays the results of these experiments indicate the twisting resulted from the initial mechanical loading of the open cross-section booms.

Thornton, E. A.↗

NASA NTRS1997

STS-85 Day 09 Highlights

On this ninth day of the STS-85 mission, the flight crew, Cmdr. Curtis L. Brown, Jr., Pilot Kent V. Rominger, Payload Cmdr. N. Jan Davis (Ph.D.), Mission Specialists Robert L. Curbeam, Jr. and Stephen K. Robinson (Ph.D.), and Payload Specialist Bjarni V. Tryggvason watch over the Manipulator Flight Demonstration (MFD) experiment while Japanese investigators again maneuvere the Small Fine Arm remotely from a control room near Mission Control. It is the final planned work with the arm during this mission. While MFD operations are ongoing, Robinson again uses the Southwest Ultraviolet Imaging System's ultraviolet imaging telescope to observe Comet Hale-Bopp and Curbeam continue his work with the Bioreactor Demonstration System designed to perform cell biology experiments under controlled conditions. Tryggvason spends his day supporting data gathering with the Microgravity Vibration Isolation Mount experiment. Before the crew's workday began, they discussed the mission's progress with reporters in the U.S. and Canada as part of the traditional crew news conference. Questions ranged from life in space for the first time space travelers to providing a report card on the more than 24 experiments being conducted throughout the mission.

Source record↗

NASA NTRS2000

TES Observations of the Martian Surface and Atmosphere

The Thermal Emission Spectrometer (TES) instrument is a Fourier transform Michelson interferometer operating with 10 or 5 cm(exp -1) sampling in the thermal infrared spectral region from 1700 to 200 cm(exp -1) (-6 to 50 micrometers) where virtually all minerals have characteristic fundamental vibrational absorption bands. The TES data used in this paper are among the 6 x 10(exp 7) spectra collected during the early mapping phase of the Mars Global Surveyor (MGS) mission from southern hemisphere winter to early summer (aerocentric longitude, L(sub s), 107 deg to 297 deg. The methodology for separating the surface and atmospheric components of the radiance from Mars, which allows detailed analysis and interpretation of surface mineralogy, is described in previous paper. Additional information is contained in original extended abstract.

Christensen, P. R.↗

NASA NTRS2010

Florida Tech CubeSat Experiment Feasibility Study

CubeSats are a relatively new type of satellite. Smaller than long-term (5+ year life expectancy) satellites, these pico-satellites are comparatively cheap, small (10x10x10 cm), and are very versatile. Universities world-wide are using CubeSats to conduct a variety of experiments in space without the need for a large experimental platform. Today CubeSats are considered to be one of the most effective ways to send a small payload into space and has attracted the attention of many educational and non-profit organizations. As this pico-satellite model continues to gain penetration into the satellite build and launch industry, it is expected that more governmental, educational, and commercial interests will emerge. As an example, more of the space-related items of high interest to the National Science Foundation may be tackled with a CubeSat platform resulting in lower life cycle costs than traditional satellite options. NASA LSP, in cooperation with the Florida Institute of Technology, has initiated a feasibility study to investigate the technical aspects of measuring and transferring vibration, acceleration, temperature, and video data from a CubeSat to NASA Hanger AE on Cape Canaveral Air Force Station (CCAFS) a.k.a. Kennedy Space Center (KSC). This report provides a technical feasibility analysis to determine whether-or-not a specific set of NASA/LSP requirements can be accomplished. Our approach has been to provide a "notional" component layout to determine the feasibility of the NASA/LSP stakeholder requirements. The notional layout is used to consider component level technical issues such as size, weight, & power (SWaP), bandwidth, and other critical technical parameters. Even though the notional components may satisfy the stated requirements and thereby demonstrate feasibility, the notional layout is NOT considered a design since no component optimization and design trade-off analysis has taken place. This activity should be accomplished in an appropriate design phase that is outside of the scope of this effort.

Arrasmith, William W.↗

NASA NTRS2012

Effect of Particle Damping on an Acoustically Excited Curved Vehicle Panel Structure with varied Equipment Assemblies

Particle dampers provide a mechanism for diverting energy away from resonant structural vibrations. This experimental study provides data from trials to determine how effective use of these dampers might be for equipment mounted to a curved orthogrid vehicle panel. Trends for damping are examined for variations in damper fill level, component mass, and excitation energy. A significant response reduction at the component level would suggest that comparatively small, thoughtfully placed, particle dampers might be advantageously used in vehicle design. The results of this test will be compared with baseline acoustic response tests and other follow-on testing involving a range of isolation and damping methods. Instrumentation consisting of accelerometers, microphones, and still photography data will be collected to correlate with the analytical results.

Parsons, David↗