Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind power generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Reflection plane tests of a wind turbine blade tip section with ailerons

Tests were conducted in the NASA Langley 30 by 60 foot Wind Tunnel on a full scale 7.31 m (24 ft) long tip section of a wind turbine rotor blade. The blade tip section was built with ailerons on the trailing edge. The ailerons, which spanned a length of 6.1 m (20 ft), were designed so that two types could be evaluated: the plain and the balanced. The ailerons were hinged on the suction surface at the 0.62 X chord station behind the leading edge. The purpose of the tests was to measure the aerodynamic characteristics of the blade section for: an angle of attack range from 0 deg to 90 deg aileron deflections from 0 deg to -90 deg, and Reynolds numbers of 0.79 and 1.5 x 10 to the 6th power. These data were then used to determine which aileron configuration had the most desirable rotor control and aerodynamic braking characteristics. Tests were also run to determine the effects of vortex generators, leading edge roughness, and the gaps between the aileron sections on the lift, drag, and chordwise force coefficients of the blade tip section.

Savino, J. M.↗
NASA NTRS1995

On the origin of 1/f spectrum of magnetic fluctuations in the solar wind

Spacecraft measurements show that the spectrum of magnetic fluctuations in the solar wind can be divided into low- and high frequency parts. The low and high frequency parts are approximately self-similar (follow a power-law) but with different spectral exponents. (There is, in addition, a very low frequency range in which the spectrum is dominated by structures coming directly from the Sun and it is not self-similar.) For the wind coming from the south polar hole the boundary between the low- and high frequency parts is at about 1 hour near 1 AU. The observed exponent of the low-frequency part is approximately -1 . The high frequency spectrum is steeper with an exponent of about -5/3 . The high frequency spectrum is commonly believed to be the result of non-linear interactions of magnetic and velocity perturbations which lead to a turbulent cascade. However, for the low frequency fluctuations, the site of origin (on the Sun, in the solar corona or in the solar wind?) and mechanism of generation remain basically unknown. In this paper we consider the origin of the 1/f spectrum. The analysis of Ulysses data is compared with analysis of Helios data and the results are used to confront possible models of origin of the spectrum.

Ruzmaikin, A.↗
NASA NTRS1989

Chromospheric-coronal coupling during solar flares: Current systems and particle acceleration

Two-dimensional (three velocity) electrostatic particle simulations are used to investigate the particle heating and acceleration associated with the impulsive phase of a solar flare. A crossfield current in the high corona (which is presumably driven by reconnection processes) is used to initiate the flare. Due to the differential motion of the electrons and ions, currents, and associated quasi-static electric fields are generated with the primary current and balancing return current being on adjacent field lines. These currents extend from the corona down into the chromosphere. Electrons can be accelerated to energies exceeding 100 keV on short time scales via the quasi-static fields and wave-particle interactions. The spectra of these electrons has a broken power-law distribution which hardens in time. The spatially separate primary and return currents are closed by the cross-field acceleration of the ambient ions into the primary current regions. These ions are then accelerated upwards into the corona by the same quasi-static electric field accelerating the electrons downwards. This acceleration can account for the broadened stationary and weak blue shifted component seen in soft x ray line emissions and enhancements in heavy ion abundances seen in the solar wind in associations with solar flares.

Winglee, Robert M.↗
NASA NTRS1994

Surface gravity waves at equilibrium with a steady wind

Observations of wave fields' spatial evolution and of gravity wave spectra S(sub omega) are analyzed on the basis of the data reported by several research groups as well as on a 2-year data set of wind and wave measurements by stationary National Oceanic and Atmospheric Administration buoys near the Hawaiian Islands. We seek to clarify the role of the wave energy advection (with the wave group velocity) in the overall energy balance. This advective transfer appears to be no less important than the local (breaking wave induced) dissipation as a factor of wind-wave equilibrium. The advection is found to manifest itself in the shape of wave spectra by reducing the rate at which the spectra density of the wave energy, S(sub omega approximately omega (exp -p), falls off as the frequency increases away from the spectra peak. This and other conclusions are derived by comparing the field observations with theoretical predictions of the weak turbulence theory for a spatially inhomogeneous, statistically stationary, wave field. The observations also indicate that the typical wave age xi = C(sub 0)/U in the open ocean is much greater than the limiting value 1.2 attributed to the 'fully developed sea.' Although the observed spectra can be approximated by a power law with a single 'effective' exponent, this apparent exponent, p, is found to depend on the wave age. At high xi and at frequencies below the generation range, -p tends to -3 rather than the value of -11/3 predicted by the Zakharov-Zaslavskii theory. This deviation is interpreted as pointing to a nonconservative nature of the inverse cascade, the latter including a leakage of energy to low-wavenumber modes. Dependence of the overall effective exponent on xi is shown to be responsible for variation in the coefficients b, B, c, C appearing in empirical fetch laws, such as xi = C bar-x (exp c) and e = B bar-x (exp B), where bar-x and e are the dimensionless fetch and wave energy, respectively.

Glazman, Roman E.↗
NASA NTRSDate not supplied

Spectral Analysis of Integrated Pressures on Patches with Unsteady Pressure-Sensitive Paint Measurements

The technique of Pressure-Sensitive Paint (PSP) is commonly used in the aerospace industry to measure surface pressures on the model of launch vehicles and airplanes in the wind tunnel test. Recent research has demonstrated that Unsteady Pressure-Sensitive Paint (uPSP) can be an essential tool for the assessment of the unsteady, aerodynamic phenomena. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. This paper describes the spectral analysis of integrated pressures on patches of the scale model of the Space Launch System (SLS) Block 1 cargo vehicle with the uPSP measurements, which were collected in the Ascent Transient Aerodynamics Test (ATAT) with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The patches are defined with x station values, indicating the position along length of the SLS vehicle, and azimuth angles of the scale model. For each patch, the polygons are determined from the surface cells of the grid of the model, clipped with the edges of the patch, and each of the polygons is divided into triangles. The integrated pressure of the patch is determined as the ratio of the sum of the forces on the triangles over the sum of the areas of the triangles. For each run of the test, the Cross Power Spectral Density (CPSD) and magnitude squared coherence are computed from the time series of the integrated pressures on the patches. The pressure integration is coded in C++ and the spectral analysis is coded in MATLAB. The results were generated with the execution of the compiled C++ and MATLAB codes in parallel on the NASA Pleiades supercomputer. The results of pressure integration and spectral analysis are presented in this paper, and the data consistency of the test is also demonstrated. Funding for this research was provided by the NASA Aerosciences Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRS1997

Physical Structure of Four Symbiotic Binaries

Disk accretion powers many astronomical objects, including pre-main sequence stars, interacting binary systems, and active galactic nuclei. Unfortunately, models developed to explain the behavior of disks and their surroundings - boundary layers, jets, and winds - lack much predictive power, because the physical mechanism driving disk evolution - the viscosity - is not understood. Observations of many types of accreting systems are needed to constrain the basic physics of disks and provide input for improved models. Symbiotic stars are an attractive laboratory for studying physical phenomena associated with disk accretion. These long period binaries (P(sub orb) approx. 2-3 yr) contain an evolved red giant star, a hot companion, and an ionized nebula. The secondary star usually is a white dwarf accreting material from the wind of its red giant companion. A good example of this type of symbiotic is BF Cygni: our analysis shows that disk accretion powers the nuclear burning shell of the hot white dwarf and also manages to eject material perpendicular to the orbital plane (Mikolajewska, Kenyon, and Mikolajewski 1989). The hot components in other symbiotic binaries appear powered by tidal overflow from a very evolved red giant companion. We recently completed a study of CI Cygni and demonstrated that the accreting secondary is a solar-type main sequence star, rather than a white dwarf (Kenyon et aL 1991). This project continued our study of symbiotic binary systems. Our general plan was to combine archival ultraviolet and optical spectrophotometry with high quality optical radial velocity observations to determine the variation of line and continuum sources as functions of orbital phase. We were very successful in generating orbital solutions and phasing UV+optical spectra for five systems: AG Dra, V443 Her, RW Hya, AG Peg, and AX Per. Summaries of our main results for these systems appear below. A second goal of our project was to consider general models for the outbursts of symbiotic stars, with an emphasis on understanding the differences between disk-driven and nuclear-powered eruptions.

Kenyon, Scott J.↗
NASA NTRS1999

The Contribution of Ionizing Stars to the Far-Infrared and Radio Emission in the Galaxy

A summary of research activities carried out in this eighth and final progress report. The final report includes: this summary document, copies of three published research papers, plus a draft manuscript of a fourth research paper entitled "The Contribution of Ionizing Stars to the FarInfrared and Radio Emission in the Milky Way; Evidence for a Swept-up Shell and Diffuse Ionized Halo around the W4 Chimney/Supershell." The main activity during the final quarterly reporting period was research on W4, including analysis of the radio and far-infrared images, generation of shell models, a literature search, and preparation of a research manuscript. There will be additional consultation with co-authors prior to submission of the paper to the Astrophysical Journal. The results will be presented at the 4th Tetons Summer Conference on "Galactic Structure, Stars, and the ISM" in May 2000. In this fourth and last paper we show W4 has a swept-up partially ionized shell of gas and dust which is powered by the OCl 352 star cluster. Analysis shows there is dense interstellar material directly below the shell, evidence that that the lower W4 shell "ran into a brick wall" and stalled, whereas the upper W4 shell achieved "breakout" to form a Galactic chimney. An ionized halo is evidence of Lyman continuum leakage which ionizes the WIM (warm ionized medium). It has long been postulated that the strong winds and abundant ionizing photons from massive stars are responsible for much of the large scale structure in the interstellar medium (ISM), including the ISM in other galaxies. However standard HII region theory predicts few photons will escape the local HII region. The significance of W4 and this work is it provides a direct example of how stellar winds power a galactic chimney, which in turn leads to a low density cavity from which ionizing photons can escape to large distances to ionize the WIM.

Terebey, S.↗
NASA NTRS2004

Far-Field Acoustic Characteristics of Multiple Blade-Vane Configurations for a High Tip Speed Fan

The acoustic characteristics of a model high-speed fan stage were measured in the NASA Glenn 9- by 15-Foot Low Speed Wind Tunnel at takeoff and approach flight conditions. The fan was designed for a corrected rotor tip speed of 442 m/s (1450 ft/s), and had a powered core, or booster stage, giving the model a nominal bypass ratio of 5. A simulated engine pylon and nozzle bifurcation was contained within the bypass duct. The fan stage consisted of all combinations of 3 possible rotors, and 3 stator vane sets. The 3 rotors were (1) wide chord, (2) forward swept, and (3) shrouded. The 3 stator sets were (1) baseline, moderately swept, (2) swept and leaned, and (3) swept integral vane/frame which incorporated some of the swept and leaned features as well as eliminated the downstream support structure. The baseline configuration is considered to be the wide chord rotor with the radial vane stator. A flyover Effective Perceived Noise Level (EPNL) code was used to generate relative EPNL values for the various configurations. The swept and leaned stator showed a 3 EPNdB reduction at lower fan speeds relative to the baseline stator; while the swept integral vane/frame stator showed lowest noise levels at high fan speeds. The baseline, wide chord rotor was typically the quietest of the three rotors. A tone removal study was performed to assess the acoustic benefits of removing the fundamental rotor interaction tone and its harmonics. Reprocessing the acoustic results with the bypass tone removed had the most impact on reducing fan noise at transonic rotor speeds. Removal of the bypass rotor interaction tones (BPF and nBPF) showed up to a 6 EPNdB noise reduction at transonic rotor speeds relative to noise levels for the baseline (wide chord rotor and radial stator; all tones present) configuration.

Woodward, Richard P.↗
NASA NTRS2016

Computational Investigation of a Boundary-Layer Ingestion Propulsion System for the Common Research Model

This thesis will examine potential propulsive and aerodynamic benefits of integrating a boundary-layer ingestion (BLI) propulsion system with a typical commercial aircraft using the Common Research Model geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment will be used to generate engine conditions for CFD analysis. Improvements to the BLI geometry will be made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.3% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from boundary-layer ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Blumenthal, Brennan↗
NASA NTRS2016

Computational Investigation of a Boundary-Layer Ingesting Propulsion System for the Common Research Model

The present paper examines potential propulsive and aerodynamic benefits of integrating a Boundary-Layer Ingestion (BLI) propulsion system into a typical commercial aircraft using the Common Research Model (CRM) geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment is used to generate engine conditions for CFD analysis. Improvements to the BLI geometry are made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method, and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2 deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.4% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from Boundary-Layer Ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Blumenthal, Brennan T.↗
NASA NTRS2011

Status of the Combined-Cycle Engine Large-Scale Inlet Mode Transition Experiment

The Large-Scale Inlet Mode Transition (LIMX) experiment is currently being conducted in the 10x10 foot supersonic wind tunnel at the NASA Glenn Research Center. The experiment has involved the efforts of a team for over four years to get to the first phase of testing, which is examining the aerodynamic characteristics of the inlet. The LIMX inlet involves dual flowpaths: one to provide flow to a turbine engine and one to provide flow to a dual-mode ramjet/scramjet. A rotating splitter cowl can close off the turbine flowpath, which would occur as the propulsion system transitions from turbine power to ramjet/scramjet power at Mach 4. The first phase of the experiment will simulate the turbine and ramjet/scramjet flows using cold pipes with flow rates controlled by mass-flow plugs. Much of the testing will characterize the performance of the turbine flowpath (total pressure recovery and distortion at the engine face location) as factors such as bleed rates and configuration and vortex generators are varied during the inlet mode transition. The performance of the inlet will also be examined at off-design Mach numbers (2.5-3.0) and at angle-of-attack.

Slater, John W.↗
NASA NTRS2013

NASA Tech Briefs, April 2013

Topics covered include: Fully Integrated, Miniature, High-Frequency Flow Probe Utilizing MEMS Leadless SOI Technology; Nanoscale Surface Plasmonics Sensor With Nanofluidic Control; Advanced Dispersed Fringe Sensing Algorithm for Coarse Phasing Segmented Mirror Telescopes; Neural Network Back-Propagation Algorithm for Sensing Hypergols; Bulk Moisture and Salinity Sensor; Change-Based Satellite Monitoring Using Broad Coverage and Targetable Sensing; Circularly Polarized Microwave Antenna Element with Very Low Off-Axis Cross-Polarization; Ultra-Low Heat-Leak, High-Temperature Superconducting Current Leads for Space Applications; Flash Cracking Reactor for Waste Plastic Processing; An Automated Safe-to-Mate (ASTM) Tester; Wireless Chalcogenide Nanoionic-Based Radio-Frequency Switch; Compute Element and Interface Box for the Hazard Detection System; DOT Transmit Module; Composite Aerogel Multifoil Protective Shielding; Li-Ion Electrolytes with Improved Safety and Tolerance to High-Voltage Systems; Polymer-Reinforced, Non-Brittle, Lightweight Cryogenic Insulation; Controlled, Site-Specific Functionalization of Carbon Nanotubes with Diazonium Salts; Regenerable Sorbent for CO2 Removal; Sprayable Aerogel Bead Compositions With High Shear Flow Resistance and High Thermal Insulation Value; Lexan Linear Shaped Charge Holder with Magnets and Backing Plate; Robotic Ankle for Omnidirectional Rock Anchors; Wind, Wave, and Tidal Energy Without Power Conditioning; An Active Heater Control Concept to Meet IXO Type Mirror Module Thermal-Structural Distortion Requirement; Waterless Clothes-Cleaning Machine; Integrated Electrical Wire Insulation Repair System; LVGEMS Time-of-Flight Mass Spectrometry on Satellites; Surface Inspection Tool for Optical Detection of Surface Defects; Per-Pixel, Dual-Counter Scheme for Optical Communications; Certification-Based Process Analysis; Surface Navigation Using Optimized Waypoints and Particle Swarm Optimization; Smart-Divert Powered Descent Guidance to Avoid the Backshell Landing Dispersion Ellipse; Estimating Foreign-Object-Debris Density from Photogrammetry Data; Adaptive Sampling of Spatiotemporal Phenomena with Optimization Criteria; Building a 2.5D Digital Elevation Model From 2D Imagery; Eyes on the Earth 3D; Target Trailing With Safe Navigation for Maritime Autonomous Surface Vehicles; Adams-Based Rover Terramechanics and Mobility Simulator - ARTEMIS; ISTP CDF Skeleton Editor; Uplink Summary Generator (ULSGEN) Version 1.0; Robotics On-Board Trainer (ROBoT); Software Engineering Tools for Scientific Models; Automatic Data Filter Customization Using a Genetic Algorithm; Tracker Toolkit; Towards Efficient Scientific Data Management Using Cloud Storage; On a Formal Tool for Reasoning About Flight Software Cost Analysis; A Nanostructured Composites Thermal Switch Controls Internal and External Short Circuit in Lithium Ion Batteries; Spacecraft Crew Cabin Condensation Control; and Functional Near-Infrared Spectroscopy Signals Measure Neuronal Activity in the Cortex.

Source record↗
NASA NTRS1994

Developing and flight testing the HL-10 lifting body: A precursor to the Space Shuttle

The origins of the lifting-body idea are traced back to the mid-1950's, when the concept of a manned satellite reentering the Earth's atmosphere in the form of a wingless lifting body was first proposed. The advantages of low reentry deceleration loads, range capability, and horizontal landing of a lifting reentry vehicle (as compared with the high deceleration loads and parachute landing of a capsule) are presented. The evolution of the hypersonic HL-10 lifting body is reviewed from the theoretical design and development process to its selection as one of two low-speed flight vehicles for fabrication and piloted flight testing. The design, development, and flight testing of the low-speed, air-launched, rocket-powered HL-10 was part of an unprecedented NASA and contractor effort. NASA Langley Research Center conceived and developed the vehicle shape and conducted numerous theoretical, experimental, and wind-tunnel studies. NASA Flight Research Center (now NASA Dryden Flight Research Center) was responsible for final low-speed (Mach numbers less than 2.0) aerodynamic analysis, piloted simulation, control law development, and flight tests. The prime contractor, Northrop Corp., was responsible for hardware design, fabrication, and integration. Interesting and unusual events in the flight testing are presented with a review of significant problems encountered in the first flight and how they were solved. Impressions by the pilots who flew the HL-10 are included. The HL-10 completed a successful 37-flight program, achieved the highest Mach number and altitude of this class vehicle, and contributed to the technology base used to develop the space shuttle and future generations of lifting bodies.

Kempel, Robert W.↗
NASA NTRS1984

Conceptual design of a fixed-pitch wind turbine generator system rated at 400 kilowatts

The design and cost aspects of a fixed pitch, 400 kW Wind Turbine Generator (WTG) concept are presented. Improvements in reliability and cost reductions were achieved with fixed pitch operation and by incorporating recent advances in WTG technology. The specifications for this WTG concept were as follows: (1) A fixed pitch, continuous wooden rotor was to be provided by the Gougeon Bros. Co. (2) An 8 leg hyperboloid tower that showed promise as a low cost structure was to be used. (3) Only commercially available components and parts that could be easily fabricated were to be considered. (4) Design features deemed desirable based on recent NASA research efforts were to be incorporated. Detailed costs and weight estimates were prepared for the second machine and a wind farm of 12 WTG's. The calculated cost of energy for the fixed pitch, twelve unit windfarm is 11.5 cents/kW hr not including the cost of land and access roads. The study shows feasibility of fixed pitch, intermediate power WTG operation.

Pintz, A.↗
NASA NTRS2022

Dayside Transient Phenomena and Their Impact on the Magnetosphere and Ionosphere

Dayside transients, such as hot flow anomalies, foreshock bubbles, magnetosheath jets, flux transfer events, and surface waves, are frequently observed upstream from the bow shock, in the magnetosheath, and at the magnetopause. They play a significant role in the solar wind-magnetosphere-ionosphere coupling. Foreshock transient phenomena, associated with variations in the solar wind dynamic pressure, deform the magnetopause, and in turn generates field-aligned currents (FACs) connected to the auroral ionosphere. Solar wind dynamic pressure variations and transient phenomena at the dayside magnetopause drive magnetospheric ultra low frequency (ULF) waves, which can play an important role in the dynamics of Earth’s radiation belts. These transient phenomena and their geoeffects have been investigated using coordinated in-situ spacecraft observations, spacecraft-borne imagers, ground-based observations, and numerical simulations. Cluster, THEMIS, Geotail, and MMS multi-mission observations allow us to track the motion and time evolution of transient phenomena at different spatial and temporal scales in detail, whereas ground-based experiments can observe the ionospheric projections of transient magnetopause phenomena such as waves on the magnetopause driven by hot flow anomalies or flux transfer events produced by bursty reconnection across their full longitudinal and latitudinal extent. Magnetohydrodynamics (MHD), hybrid, and particle-in-cell (PIC) simulations are powerful tools to simulate the dayside transient phenomena. This paper provides a comprehensive review of the present understanding of dayside transient phenomena at Earth and other planets, their geoeffects, and outstanding questions.

Bow shock↗
NASA NTRS1994

On the Lighthill relationship and sound generation from isotropic turbulence

In 1952, Lighthill developed a theory for determining the sound generated by a turbulent motion of a fluid. With some statistical assumptions, Proudman applied this theory to estimate the acoustic power of isotropic turbulence. Recently, Lighthill established a simple relationship that relates the fourth-order retarded time and space covariance of his stress tensor to the corresponding second-order covariance and the turbulent flatness factor, without making statistical assumptions for a homogeneous turbulence. Lilley revisited Proudman's work and applied the Lighthill relationship to evaluate directly the radiated acoustic power from isotropic turbulence. After choosing the time separation dependence in the two-point velocity time and space covariance based on the insights gained from direct numerical simulations, Lilley concluded that the Proudman constant is determined by the turbulent flatness factor and the second-order spatial velocity covariance. In order to estimate the Proudman constant at high Reynolds numbers, we analyzed a unique data set of measurements in a large wind tunnel and atmospheric surface layer that covers a range of the Taylor microscale based on Reynolds numbers 2.0 x 10(exp 3) less than or equal to R(sub lambda) less than or equal to 12.7 x 10(exp 3). Our measurements demonstrate that the Lighthill relationship is a good approximation, providing additional support to Lilley's approach. The flatness factor is found between 2.7 - 3.3 and the second order spatial velocity covariance is obtained. Based on these experimental data, the Proudman constant is estimated to be 0.68 - 3.68.

Zhou, YE↗
NASA NTRS2013

Superconductors Enable Lower Cost MRI Systems

The future looks bright, light, and green, especially where aircraft are concerned. The division of NASA s Fundamental Aeronautics Program called the Subsonic Fixed Wing Project is aiming to reach new heights by 2025-2035, improving the efficiency and environmental impact of air travel by developing new capabilities for cleaner, quieter, and more fuel efficient aircraft. One of the many ways NASA plans to reach its aviation goals is by combining new aircraft configurations with an advanced turboelectric distributed propulsion (TeDP) system. Jeff Trudell, an engineer at Glenn Research Center, says, "The TeDP system consists of gas turbines generating electricity to power a large number of distributed motor-driven fans embedded into the airframe." The combined effect increases the effective bypass ratio and reduces drag to meet future goals. "While room temperature components may help reduce emissions and noise in a TeDP system, cryogenic superconducting electric motors and generators are essential to reduce fuel burn," says Trudell. Superconductors provide significantly higher current densities and smaller and lighter designs than room temperature equivalents. Superconductors are also able to conduct direct current without resistance (loss of energy) below a critical temperature and applied field. Unfortunately, alternating current (AC) losses represent the major part of the heat load and depend on the frequency of the current and applied field. A refrigeration system is necessary to remove the losses and its weight increases with decreasing temperature. In 2001, a material called magnesium diboride (MgB2) was discovered to be superconducting. The challenge, however, has been learning to manufacture MgB2 inexpensively and in long lengths to wind into large coils while meeting the application requirements.

Source record↗
NASA NTRS1997

Physics of Rotation Powered Pulsars and Their Nebulae

This letter is my progress report for the Astrophysics Theory grant. The first goal of the research supported by this grant is to produce a time dependent theory of the unsteady relativistic collisionless shock wave terminating the relativistic wind from a pulsar, and compare the predicted surface brightness fluctuations to Hubble Space Telescope observations of the wisps in the Crab Nebula. The second goal is to model the production of electron-positron pairs over the polar caps of rotation powered pulsars, and use the results to predict the heating of the surface due to particle trapping and bombardment of the atmosphere at the base of the polar field lines. We have succeeded in creating a one dimensional hybrid code, in which the electron-positron pairs incident on the shock structure are modeled as a relativistic, adiabatic, ideal MHD fluid, while the heavy ions are treated as particles using a particle-in-cell algorithm. The electromagnetic fields are evaluated from the currents and charge densities in the pairs and the ions, while the particles and the fluid accelerate in response to the computed self-consistent electromagnetic fields. The results are promising, in that the underlying ion cyclotron instability generates finite amplitude, propagating magnetosonic waves in the pairs, whose wavelengths and frequencies, when translated into physical units, are comparable to the observed running waves of brightness observed by HST near the Crab pulsar. The code is undergoing a number of tests, to assure us that this preliminary correspondence is not an artifact. In the coming year, the observational appearance of the models will be computed and compared to the HST observations of the Crab now in hand, and used to predict the HST results which will be obtained the year after next. WE also developed a one dimensional cascade theory for pair creation over pulsars' polar caps. A linear integral equation describing the synchrotron cascade has been derived and solved by iterative techniques, in the case when a high energy electron moving parallel to a star centered dipole magnetic field initiates the cascade through curvature gamma ray emission.

Arons, Jonathan↗