SEARCH · Search NASA

Results for “Computer Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗

NASA NTRS2022

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Boundary layer transition↗

NASA NTRS1993

Generic hypersonic vehicle performance model

An integrated computational model of a generic hypersonic vehicle was developed for the purpose of determining the vehicle's performance characteristics, which include the lift, drag, thrust, and moment acting on the vehicle at specified altitude, flight condition, and vehicular configuration. The lift, drag, thrust, and moment are developed for the body fixed coordinate system. These forces and moments arise from both aerodynamic and propulsive sources. SCRAMjet engine performance characteristics, such as fuel flow rate, can also be determined. The vehicle is assumed to be a lifting body with a single aerodynamic control surface. The body shape and control surface location are arbitrary and must be defined. The aerodynamics are calculated using either 2-dimensional Newtonian or modified Newtonian theory and approximate high-Mach-number Prandtl-Meyer expansion theory. Skin-friction drag was also accounted for. The skin-friction drag coefficient is a function of the freestream Mach number. The data for the skin-friction drag coefficient values were taken from NASA Technical Memorandum 102610. The modeling of the vehicle's SCRAMjet engine is based on quasi 1-dimensional gas dynamics for the engine diffuser, nozzle, and the combustor with heat addition. The engine has three variable inputs for control: the engine inlet diffuser area ratio, the total temperature rise through the combustor due to combustion of the fuel, and the engine internal expansion nozzle area ratio. The pressure distribution over the vehicle's lower aft body surface, which acts as an external nozzle, is calculated using a combination of quasi 1-dimensional gas dynamic theory and Newtonian or modified Newtonian theory. The exhaust plume shape is determined by matching the pressure inside the plume, calculated from the gas dynamic equations, with the freestream pressure, calculated from Newtonian or Modified Newtonian theory. In this manner, the pressure distribution along the vehicle after body expansion surface is then determined. The aerodynamic modeling, the engine modeling, and the exhaust plume analysis are described in more detail. A description of the computer code used to perform the above calculations is given and an input/output example is then given. The computer code is available on a Macintosh floppy disk.

Chavez, Frank R.↗

NASA NTRS1982

Cartographic Modeling: Computer-assisted Analysis of Spatially Defined Neighborhoods

Cartographic models addressing a wide variety of applications are composed of fundamental map processing operations. These primitive operations are neither data base nor application-specific. By organizing the set of operations into a mathematical-like structure, the basis for a generalized cartographic modeling framework can be developed. Among the major classes of primitive operations are those associated with reclassifying map categories, overlaying maps, determining distance and connectivity, and characterizing cartographic neighborhoods. The conceptual framework of cartographic modeling is established and techniques for characterizing neighborhoods are used as a means of demonstrating some of the more sophisticated procedures of computer-assisted map analysis. A cartographic model for assessing effective roundwood supply is briefly described as an example of a computer analysis. Most of the techniques described have been implemented as part of the map analysis package developed at the Yale School of Forestry and Environmental Studies.

Berry, J. K.↗

NASA NTRS2019

Computational Micromechanics Model for the Analysis of Fiber Kinking in Unidirectional FRP

A computational micromechanics (CMM) model is developed to analyze fiber kinking, which is a failure mechanism that takes place in fiber-reinforced composites when they are loaded under longitudinal compression. The CMM model consists of a single AS4 carbon fiber with an initial misalignment embedded in an 8552 polymer matrix. The deformation of the model is governed by periodic boundary conditions (PBC). The relatively simple CMM model enables the evaluation of the role played by initial misalignment of the fiber, shear yielding of the matrix and fiber-matrix debonding. A novel microscale experimental technique devoted to the characterization of the longitudinal compressive strength of the fibers, X(sup f)(sub c) , was developed. By exercising the model and comparing it with several existing models in the literature, the nonlinear shear response of the composite lamina was shown to play a fundamental role not only in the prediction of the compressive strength X(sub c), but also during the post-peak regime in terms of residual stress σ(sub r) and fiber rotation φ. Finally, the influence of the fiber-matrix interface damage (not considered in most other fiber kinking models) on the fiber kinking phenomenon was assessed through a parametric study.

Polymer-matrix composites (PMC)↗

NASA NTRS1988

Computer-aided modeling and prediction of performance of the modified Lundell class of alternators in space station solar dynamic power systems

The main purpose of this project is the development of computer-aided models for purposes of studying the effects of various design changes on the parameters and performance characteristics of the modified Lundell class of alternators (MLA) as components of a solar dynamic power system supplying electric energy needs in the forthcoming space station. Key to this modeling effort is the computation of magnetic field distribution in MLAs. Since the nature of the magnetic field is three-dimensional, the first step in the investigation was to apply the finite element method to discretize volume, using the tetrahedron as the basic 3-D element. Details of the stator 3-D finite element grid are given. A preliminary look at the early stage of a 3-D rotor grid is presented.

Demerdash, Nabeel A. O.↗

NASA NTRS1982

Slab-geometry Nd:glass laser performance studies

It is noted that slab-geometry solid-state lasers potentially provide significant performance improvements relative to conventional rod-geometry lasers. Experimental measurements that use an Nd:glass test-bed slab laser are presented. A comparison is made between the results and computer-model predictions of the slab-geometry approach. The computer model calculates and displays the temperature and stress fields in the slab, and on the basis of these predicts birefringence and index-of-refraction distributions. The effect that these distributions have on optical propagation is determined in a polarization-sensitive ray-tracing section of the model. Calculations are also made of stress-induced surface curvature and the resulting focusing effects. The measurements are found to be in good agreement with the computer-model predictions. It is concluded that the slab configuration offers significant laser-performance advantages in comparison with the traditional rod-laser geometry.

Eggleston, J. M.↗

NASA NTRS1985

Duct flow nonuniformities study for space shuttle main engine

To improve the Space Shuttle Main Engine (SSME) design and for future use in the development of generation rocket engines, a combined experimental/analytical study was undertaken with the goals of first, establishing an experimental data base for the flow conditions in the SSME high pressure fuel turbopump (HPFTP) hot gas manifold (HGM) and, second, setting up a computer model of the SSME HGM flow field. Using the test data to verify the computer model it should be possible in the future to computationally scan contemplated advanced design configurations and limit costly testing to the most promising design. The effort of establishing and using the computer model is detailed. The comparison of computational results and experimental data observed clearly demonstrate that computational fluid mechanics (CFD) techniques can be used successfully to predict the gross features of three dimensional fluid flow through configurations as intricate as the SSME turbopump hot gas manifold.

Thoenes, J.↗

NASA NTRS1970

Patterns of equivalent blackbody temperature and reflectance of model clouds computed by changing radiometers field of view

Equivalent blackbody temperature and reflectance patterns of model clouds computed by changing radiometer field of view

Tecson, J. J.↗

NASA NTRS1995

Industry-Wide Workshop on Computational Turbulence Modeling

This publication contains the presentations made at the Industry-Wide Workshop on Computational Turbulence Modeling which took place on October 6-7, 1994. The purpose of the workshop was to initiate the transfer of technology developed at Lewis Research Center to industry and to discuss the current status and the future needs of turbulence models in industrial CFD.

Shabbir, Aamir↗

NASA NTRS1979

Frost formation on an airfoil: A mathematical model 1

A computer model to predict the frost formation process on a flat plate was developed for application to most environmental conditions under which frost occurs. The model was analytically based on a generalized frost thermal conductivity expression, on frost density and thickness rate equations, and on modified heat and mass transfer coefficients designed to fit the available experimental data. The broad experimental ranges reflected by the extremes in ambient humidities, wall temperatures, and convective flow properties in the various publications which were examined served to severely test the flexibility of the model. An efficient numerical integration scheme was developed to solve for the frost surface temperature, density, and thickness under the changing environmental conditions. The comparison of results with experimental data was very encouraging.

Dietenberger, M.↗

NASA NTRS1984

Fully-coupled analysis of jet mixing problems. Part 1. Shock-capturing model, SCIPVIS

A computational model, SCIPVIS, is described which predicts the multiple cell shock structure in imperfectly expanded, turbulent, axisymmetric jets. The model spatially integrates the parabolized Navier-Stokes jet mixing equations using a shock-capturing approach in supersonic flow regions and a pressure-split approximation in subsonic flow regions. The regions are coupled using a viscous-characteristic procedure. Turbulence processes are represented via the solution of compressibility-corrected two-equation turbulence models. The formation of Mach discs in the jet and the interactive analysis of the wake-like mixing process occurring behind Mach discs is handled in a rigorous manner. Calculations are presented exhibiting the fundamental interactive processes occurring in supersonic jets and the model is assessed via comparisons with detailed laboratory data for a variety of under- and overexpanded jets.

Dash, S. M.↗

NASA NTRS1985

Currents to the ionosphere from thunderstorm generators - A model study

A computer model (Nisbet, 1983) was used to evaluate the role of thunderstorm clouds in generating the currents necessary for the maintenance of the ionospheric potential. The effects of variations in the breakdown electric field below the lower charge center, heights of the upper and lower charge centers, generator currents and geometry, as well as of the conductivity profile of the cloud, the surrounding air, and the ionosphere, on the currents to the ionosphere were examined. It was shown that the most important single variable controlling the ionospheric current/generator current ratio for both very active storms and for storms that do not produce lightning is the height of the lower active center. The ionospheric conductivity has a negligible effect on the total current to the ionosphere, although it is very important in controlling the electric field and current density waveforms above the cloud.

Nisbet, J. S.↗

NASA NTRS1992

Advanced propulsion for LEO-Moon transport. 3: Transportation model

A simplified computational model of low Earth orbit-Moon transportation system has been developed to provide insight into the benefits of new transportation technologies. A reference transportation infrastructure, based upon near-term technology developments, is used as a departure point for assessing other, more advanced alternatives. Comparison of the benefits of technology application, measured in terms of a mass payback ratio, suggests that several of the advanced technology alternatives could substantially improve the efficiency of low Earth orbit-Moon transportation.

Henley, Mark W.↗

NASA NTRS2006

Computational Aeroelastic Modeling of Airframes and TurboMachinery: Progress and Challenges

Computational analyses such as computational fluid dynamics and computational structural dynamics have made major advances toward maturity as engineering tools. Computational aeroelasticity is the integration of these disciplines. As computational aeroelasticity matures it too finds an increasing role in the design and analysis of aerospace vehicles. This paper presents a survey of the current state of computational aeroelasticity with a discussion of recent research, success and continuing challenges in its progressive integration into multidisciplinary aerospace design. This paper approaches computational aeroelasticity from the perspective of the two main areas of application: airframe and turbomachinery design. An overview will be presented of the different prediction methods used for each field of application. Differing levels of nonlinear modeling will be discussed with insight into accuracy versus complexity and computational requirements. Subjects will include current advanced methods (linear and nonlinear), nonlinear flow models, use of order reduction techniques and future trends in incorporating structural nonlinearity. Examples in which computational aeroelasticity is currently being integrated into the design of airframes and turbomachinery will be presented.

Bartels, R. E.↗

NASA NTRS1980

Solar insolation model

Computer program SOLINS helps engineers with relatively complex task of choosing best orientation of fixed flat-plate solar collectors for local conditions. Program models average hourly solar insolation on fixed but arbitrarily-oriented surface. Consideration is given to problems of array spacing, shadowing, and use of augmentation reflectors to increase insolation at collector surface.

Smith, J. H.↗

NASA NTRS1989

Queuing theory models for computer networks

A set of simple queuing theory models which can model the average response of a network of computers to a given traffic load has been implemented using a spreadsheet. The impact of variations in traffic patterns and intensities, channel capacities, and message protocols can be assessed using them because of the lack of fine detail in the network traffic rates, traffic patterns, and the hardware used to implement the networks. A sample use of the models applied to a realistic problem is included in appendix A. Appendix B provides a glossary of terms used in this paper. This Ames Research Center computer communication network is an evolving network of local area networks (LANs) connected via gateways and high-speed backbone communication channels. Intelligent planning of expansion and improvement requires understanding the behavior of the individual LANs as well as the collection of networks as a whole.

Galant, David C.↗

NASA NTRS2007

Aeroelastic Model Structure Computation for Envelope Expansion

Structure detection is a procedure for selecting a subset of candidate terms, from a full model description, that best describes the observed output. This is a necessary procedure to compute an efficient system description which may afford greater insight into the functionality of the system or a simpler controller design. Structure computation as a tool for black-box modelling may be of critical importance in the development of robust, parsimonious models for the flight-test community. Moreover, this approach may lead to efficient strategies for rapid envelope expansion which may save significant development time and costs. In this study, a least absolute shrinkage and selection operator (LASSO) technique is investigated for computing efficient model descriptions of nonlinear aeroelastic systems. The LASSO minimises the residual sum of squares by the addition of an l(sub 1) penalty term on the parameter vector of the traditional 2 minimisation problem. Its use for structure detection is a natural extension of this constrained minimisation approach to pseudolinear regression problems which produces some model parameters that are exactly zero and, therefore, yields a parsimonious system description. Applicability of this technique for model structure computation for the F/A-18 Active Aeroelastic Wing using flight test data is shown for several flight conditions (Mach numbers) by identifying a parsimonious system description with a high percent fit for cross-validated data.

Kukreja, Sunil L.↗