Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design and modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Advanced low NO/x/ combustors for supersonic high-altitude aircraft gas turbines

A test rig program was conducted with the objective of evaluating and minimizing the exhaust emissions, in particular NO(x), of two advanced aircraft combustor concepts at a simulated, high-altitude cruise condition. The two combustor designs, both members of the lean-reaction, pre-mixed family, are known as the Jet Induced Circulation (JIC) combustor and the Vortex Air Blast (VAB) combustor and were rig tested in the form of reverse flow can combustors in the 0.127-m size range. Various configuration modifications were applied to each of the initial JIC and VAB combustor model designs in an effort to reduce the emissions levels. The VAB combustor demonstrated a NO(x) level of 1.1 gm NO2/kg fuel with essentially 100 percent combustion efficiency at the simulated cruise combustor condition of 507 kPa, 833 K inlet pressure and temperature, respectively and 1778 K outlet temperature on Jet-A1 fuel. In addition, emissions data were obtained at low combustor inlet pressure and temperatures that indicate the potential performance at engine off-design conditions.

Roberts, P. B.↗
NASA NTRS1980

Preliminary demonstration of a robust controller design method

Alternative computational procedures for obtaining a feedback control law which yields a control signal based on measurable quantitites are evaluated. The three methods evaluated are: (1) the standard linear quadratic regulator design model; (2) minimization of the norm of the feedback matrix, k via nonlinear programming subject to the constraint that the closed loop eigenvalues be in a specified domain in the complex plane; and (3) maximize the angles between the closed loop eigenvectors in combination with minimizing the norm of K also via the constrained nonlinear programming. The third or robust design method was chosen to yield a closed loop system whose eigenvalues are insensitive to small changes in the A and B matrices. The relationship between orthogonality of closed loop eigenvectors and the sensitivity of closed loop eigenvalues is described. Computer programs are described.

Anderson, L. R.↗
NASA NTRS1976

A comparison between conventional and LANDSAT based hydrologic modeling: The Four Mile Run case study

Models designed to support the hydrologic studies associated with urban water resources planning require input parameters that are defined in terms of land cover. Estimating the land cover is a difficult and expensive task when drainage areas larger than a few sq. km are involved. Conventional and LANDSAT based methods for estimating the land cover based input parameters required by hydrologic planning models were compared in a case study of the 50.5 sq. km (19.5 sq. mi) Four Mile Run Watershed in Virginia. Results of the study indicate that the LANDSAT based approach is highly cost effective for planning model studies. The conventional approach to define inputs was based on 1:3600 aerial photos, required 110 man-days and a total cost of $14,000. The LANDSAT based approach required 6.9 man-days and cost $2,350. The conventional and LANDSAT based models gave similar results relative to discharges and estimated annual damages expected from no flood control, channelization, and detention storage alternatives.

Ragan, R. M.↗
NASA NTRS2009

Component and System Sensitivity Considerations for Design of a Lunar ISRU Oxygen Production Plant

Component and system sensitivities of some design parameters of ISRU system components are analyzed. The differences between terrestrial and lunar excavation are discussed, and a qualitative comparison of large and small excavators is started. The effect of excavator size on the size of the ISRU plant's regolith hoppers is presented. Optimum operating conditions of both hydrogen and carbothermal reduction reactors are explored using recently developed analytical models. Design parameters such as batch size, conversion fraction, and maximum particle size are considered for a hydrogen reduction reactor while batch size, conversion fraction, number of melt zones, and methane flow rate are considered for a carbothermal reduction reactor. For both reactor types the effect of reactor operation on system energy and regolith delivery requirements is presented.

Linne, Diane L.↗
NASA NTRS1984

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary-layer characteristics at Reynolds numbers exceeding one billion is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility. The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentationn techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, W. S.↗
NASA NTRSDate not supplied

Mars Sample Return, Sample Retrieval Lander, Reaction Control System Jet Interaction Supersonic Wind Tunnel Test Overview with CFD Predictions

NASA's Mars Sample Return campaign will be launching several missions over the next decade that will work together to return rock samples from Mars back to Earth. The Sample Retrieval Lander (SRL) will deliver the Mars Ascent Vehicle and fetch rover to the surface of Mars in 2006. Rock samples collected by the Mars 2020 Perseverance rover, landing in early 2021, will be loaded on the the ascent vehicle to be launched into Mars orbit for retrieval by yet another spacecraft. The Sample Retrieval Lander will be a blunt entry capsule similar to past Mars entry vehicles like Mars Science Laboratory and Viking. The vehicle will fly a guided entry, using a small lift vector produced by a non-zero trim angle of attack to eliminate downrange and crossrange position errors at the point of parachute deploy. This energy and heading management is achieved with a reaction control system (RCS) that directs the bank angle of the vehicle and also minimizes unwanted capsule dynamics. The reaction control system and control design is based on the Mars Science Laboratory and Mars 2020 RCS systems. However, due to packaging constraints, the backshell of this new entry vehicle has a different geometry than those earlier designs. To certify the RCS system for flight the project must characterize the jet plume interactions with the capsule backshell that could impair or significantly augment the RCS control authority. This characterization will be done through a combination of computational fluid dynamics (CFD) analysis and wind tunnel test. Two candidate arrangements of the RCS jets have been identified for the SRL vehicle and are currently under evaluation before final selection. The aero/RCS plume interactions of these candidate configurations have been measured in a supersonic wind tunnel test in NASA Langley's Unitary Plan Wind Tunnel. The test was conducted in the fall of 2020 and data is currently being reduced. An overview of the candidate RCS configurations are presented here with an overview of the wind tunnel model design, jet scaling and scaled nozzle design, and the test matrix. Preliminary CFD runs are presented with an assessment of the predicted plumes and their interaction with the wake flow of the vehicle. The predicted effects of the model sting is provided as well. This high fidelity wind tunnel test is being conducted much earlier in the SRL project than would normally be done. The test was funded as part of a CFD evaluation task funded by NASA's Aerosciences Evaluation and Test Capabilities Project. The objective of the evaluation task was to compare the ability of CFD to predict complex flows with data that can be measured in the Langley Unitary Plan Wind Tunnel. RCS Jet interactions were selected as a type of complex flow that is important to NASA missions. In addition to providing useful data to the SRL project, there was added emphasis on quantifying the accuracy of the CFD predictions and wind tunnel test data. An overview of the uncertainty quantification methodologies for computational and experimental portions of this test is presented.

blunt body↗
NASA NTRS1980

Turbine endwall two-cylinder program

Progress is reported in an effort to study the three dimensional separation of fluid flow around two isolated cylinders mounted on an endwall. The design and performance of a hydrogen bubble generator for water tunnel tests to determine bulk flow properties and to measure main stream velocity and boundary layer thickness are described. Although the water tunnel tests are behind schedule because of inlet distortion problems, tests are far enough along to indicate cylinder spacing, wall effects and low Reynolds number behavior, all of which impacted wind tunnel model design. The construction, assembly, and operation of the wind tunnel and the check out of its characteristics are described. An off-body potential flow program was adapted to calculate normal streams streamwise pressure gradients at the saddle point locations.

Langston, L. S.↗
NASA NTRS1992

Acquisition and production of skilled behavior in dynamic decision-making tasks

Detailed summaries of two NASA-funded research projects are provided. The first project was an ecological task analysis of the Star Cruiser model. Star Cruiser is a psychological model designed to test a subject's level of cognitive activity. Ecological task analysis is used as a framework to predict the types of cognitive activity required to achieve productive behavior and to suggest how interfaces can be manipulated to alleviate certain types of cognitive demands. The second project is presented in the form of a thesis for the Masters Degree. The thesis discusses the modeling of decision-making through the use of neural network and genetic-algorithm machine learning technologies.

Kirlik, Alex↗
NASA NTRS1999

A Computational/Experimental Study of Two Optimized Supersonic Transport Designs and the Reference H Baseline

Two supersonic transport configurations designed by use of non-linear aerodynamic optimization methods are compared with a linearly designed baseline configuration. One optimized configuration, designated Ames 7-04, was designed at NASA Ames Research Center using an Euler flow solver, and the other, designated Boeing W27, was designed at Boeing using a full-potential method. The two optimized configurations and the baseline were tested in the NASA Langley Unitary Plan Supersonic Wind Tunnel to evaluate the non-linear design optimization methodologies. In addition, the experimental results are compared with computational predictions for each of the three configurations from the Enter flow solver, AIRPLANE. The computational and experimental results both indicate moderate to substantial performance gains for the optimized configurations over the baseline configuration. The computed performance changes with and without diverters and nacelles were in excellent agreement with experiment for all three models. Comparisons of the computational and experimental cruise drag increments for the optimized configurations relative to the baseline show excellent agreement for the model designed by the Euler method, but poorer comparisons were found for the configuration designed by the full-potential code.

Cliff, Susan E.↗
NASA NTRS1977

A model to investigate the influence of suspended sediment on the mass transport of a pollutant in open channel flow

An explicit two-dimensional finite difference model, designed to investigate the influence of suspended sediment on the pollutant transport process, is presented. Specific attention is directed toward examining the role of suspended sediment in: (1) the turbulent vertical transport mechanism in a stratified flow, and (2) pollutant uptake due to sorption. Results presented indicate that suspended sediment plays a major role in the pollutant transport process, and subsequently, any meaningful attempt to model the fate of a pollutant in an alluvial channel must account for the presence of a suspended sediment concentration profile. Similarly, the vertical and longitudinal pollutant concentration distributions provided by the model may be utilized to improve upon the predictive capacities of existing water quality models.

Chapman, R. S.↗
NASA NTRS1988

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary layer characteristics at Reynolds numbers exceeding 1 x 10 to the 9th is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility (NTF). The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentation techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, William S.↗
NASA NTRS1980

Loss model for off-design performance analysis of radial turbines with pivoting-vane, variable-area stators

An off-design performance loss model for a radial turbine with pivoting, variable-area stators is developed through a combination of analytical modeling and experimental data analysis. A viscous loss model is used for the variation in stator loss with setting angle, and stator vane end-clearance leakage effects are predicted by a clearance flow model. The variation of rotor loss coefficient with stator setting angle is obtained by means of an analytical matching of experimental data for a rotor that was tested with six stators, having throat areas from 20 to 144% of the design area. An incidence loss model is selected to obtain best agreement with experimental data. The stator vane end-clearance leakage model predicts increasing mass flow and decreasing efficiency as a result of end-clearances, with changes becoming significantly larger with decreasing stator area.

Meitner, P. L.↗
NASA NTRS2016

Trajectory Design Employing Convex Optimization for Landing on Irregularly Shaped Asteroids

Mission proposals that land spacecraft on asteroids are becoming increasingly popular. However, in order to have a successful mission the spacecraft must reliably and softly land at the intended landing site with pinpoint precision. The problem under investigation is how to design a propellant optimal powered descent trajectory that can be quickly computed onboard the spacecraft, without interaction from the ground control. The propellant optimal control problem in this work is to determine the optimal finite thrust vector to land the spacecraft at a specified location, in the presence of a highly nonlinear gravity field, subject to various mission and operational constraints. The proposed solution uses convex optimization, a gravity model with higher fidelity than Newtonian, and an iterative solution process for a fixed final time problem. In addition, a second optimization method is wrapped around the convex optimization problem to determine the optimal flight time that yields the lowest propellant usage over all flight times. Gravity models designed for irregularly shaped asteroids are investigated. Success of the algorithm is demonstrated by designing powered descent trajectories for the elongated binary asteroid Castalia.

Pinson, Robin M.↗
NASA NTRS1989

Uncertainty bounds using sector theory

An approach based on sector-stability theory can furnish a description of the uncertainty associated with the frequency response of a model, given sector-bounds on the individual parameters of the model. The application of the sector-based approach to the formulation of useful uncertainty descriptions for linear, time-invariant multivariable systems is presently explored, and the approach is applied to two generic forms of parameter uncertainty in order to investigate its advantages and limitations. The results obtained show that sector-uncertainty bounds can be used to evaluate the impact of parameter uncertainties on the frequency response of the design model.

Waszak, Martin R.↗
NASA NTRS2004

Special Purpose Crew Restraints for Teleoperation

With permanent human presence onboard the International Space Station (ISS), and long duration space missions being planned for the moon and Mars, humans will be living and working in microgravity over increasingly long periods of time. In addition to weightlessness, the confined nature of a spacecraft environment results in ergonomic challenges such as limited visibility, and access to the activity area. These challenges can result in prolonged periods of unnatural postures for the crew, ultimately causing pain, injury, and loss of productivity. Determining the right set of human factors requirements and providing an ergonomically designed environment is crucial to mission success. While a number of general purpose restraints have been used on ISS (handrails, foot loops), experience has shown that these general purpose restraints may not be optimal, or even acceptable for some tasks that have unique requirements. For example, some onboard activities require extreme stability (e.g., glovebox microsurgery), and others involve the use of arm, torso and foot movements in order to perform the task (e-g. robotic teleoperation); standard restraint systems will not work in these situations. The Usability Testing and Analysis Facility (WAF) at the NASA Johnson Space Center began evaluations of crew restraints for these special situations by looking at NASAs Robonaut. Developed by the Robot Systems Technology Branch, Robonaut is a humanoid robot that can be remotely operated through a tetepresence control system by an operator. It was designed to perform work in hazardous environments (e.g., Extra Vehicular Activities). A Robonaut restraint was designed, modeled for the population, and ultimately tested onboard the KC-135 microgravity aircraft. While in microgravity, participants were asked to get in and out of the restraint from different locations, perform maximum reach exercises, and finally to teleoperate Robonaut while in the restraint. The sessions were videotaped, and participants completed a questionnaire at the end of each flight day. Results from this evaluation are being used to develop the human factors design requirements for teleoperation tasks in microgravity.

Whitmore, Mihriban↗
NASA NTRS1998

Optimal Controller Design for the Microgravity Isolation Mount (MIM)

H2 controllers, when designed using an appropriate design model and carefully chosen frequency weightings, appear to provide robust performance and robust stability for Microgravity Isolation Mount (MIM). The STS-85 flight data will be used to evaluate the H2 controllers' performance on the actual hardware under working conditions. Next, full-order H-infinity controllers will be developed, as an intermediate step, in order to determine appropriate H-infinity performance weights for use in the mixed-norm design. Finally the basic procedure outlined above will be used to develop fixed-order mixed-norm controllers for MIM.

Hampton, R. David↗
NASA NTRS2014

Validation of Solar Sail Simulations for the NASA Solar Sail Demonstration Project

NASA's Solar Sail Demonstration project partner L'Garde is currently assembling a flight-like sail assembly for a series of ground demonstration tests beginning in 2015. For future missions of this sail that might validate solar sail technology, it is necessary to have an accurate sail thrust model. One of the primary requirements of a proposed potential technology validation mission will be to demonstrate solar sail thrust over a set time period, which for this project is nominally 30 days. This requirement would be met by comparing a L'Garde-developed trajectory simulation to the as-flown trajectory. The current sail simulation baseline for L'Garde is a Systems Tool Kit (STK) plug-in that includes a custom-designed model of the L'Garde sail. The STK simulation has been verified for a flat plate model by comparing it to the NASA-developed Solar Sail Spaceflight Simulation Software (S5). S5 matched STK with a high degree of accuracy and the results of the validation indicate that the L'Garde STK model is accurate enough to meet the potential future mission requirements. Additionally, since the L'Garde sail deviates considerably from a flat plate, a force model for a non-flat sail provided by L'Garde sail was also tested and compared to a flat plate model in S5. This result will be used in the future as a basis of comparison to the non-flat sail model being developed for STK.

Braafladt, Alexander C.↗