Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering - Particle accelerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

An experimental study of propeller-induced structural vibration and interior noise

This paper presents results of tests conducted to study fuselage sidewall dynamics and their effects on the cabin interior noise of a twin-engine, propeller-driven, light aircraft. Data on the dynamic behavior were obtained by slowly sweeping the RPM of one of the engines while the aircraft was stationary on the ground. This technique allowed frequency response plots of the sidewall structural accelerations to be obtained. These accelerations are compared to similar results from a test using a mechanical shaker in order to evaluate the structural dynamic response caused by the harmonics of the propeller blade passage tone. The dynamic response of the fuselage sidewall is also discussed as a noise transmission mechanism. A second mechanism for noise transmission through the fuselage sidewall was investigated by opening the copilot's window. The results illustrate the complex nature of the noise transmission mechanisms and the importance of correctly assessing noise paths.

Howlett, J. T.↗
NASA NTRS1989

Low-speed, high-lift aerodynamic characteristics of slender, hypersonic accelerator-type configurations

Two investigations were conducted in the Langley 14 by 22 Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of a generic hypersonic accelerator-type configuration. The model was a delta wing configuration incorporating a conical forebody, a simulated wrap-around engine package, and a truncated conical aftbody. Six-component force and moment data were obtained over a range of attack from -4 to 30 degrees and for a sideslip range of + or - 20 degrees. In addition to tests of the basic configuration, component build-up tests were conducted; and the effects of power, forebody nose geometry, canard surfaces, fuselage strakes, and engines on the lower surface alone were also determined. Control power available from deflections of wing flaps and aftbody flaps was also investigated and found to be significantly increased during power-on conditions. Large yawing moments resulted from asymmetric flow fields exhibited by the forebody as revealed by both surface pressure data and flow visualization. Increasing nose bluntness reduced the yawing-moment asymmetry, and the addition of a canard eliminated the yawing-moment asymmetry.

Gatlin, Gregory M.↗
NASA NTRSDate not supplied

Model-Based Systems Analysis and Engineering for the Sustainable Flight National Partnership

NASA is committed to supporting the U.S. climate goal of achieving net-zero greenhouse gas emissions from the aviation sector by 2050, as outlined in the U.S. 2021 Aviation Climate Action Plan. Through the Sustainable Flight National Partnership (SFNP), NASA is leading federal agencies and industry partners to accelerate the development of technologies capable of supporting the nation's aviation sustainability goals for products targeting an entry-into-service of 2035. To support the SFNP, NASA is developing a Model-Based Systems Analysis & Engineering (MBSA&E) framework which will serve to digitally integrate the work across numerous projects and demonstrations to the systems-level for relevant vision vehicle concepts. This presentation summarizes the MBSA&E motivation, development efforts, and future work.

Model Based Engineering↗
NASA NTRS2009

Atomic References for Measuring Small Accelerations

Accelerometer systems that would combine the best features of both conventional (e.g., mechanical) accelerometers and atom interferometer accelerometers (AIAs) have been proposed. These systems are intended mainly for use in scientific research aboard spacecraft but may also be useful on Earth in special military, geological, and civil-engineering applications. Conventional accelerometers can be sensitive, can have high dynamic range, and can have high frequency response, but they lack accuracy and long-term stability. AIAs have low frequency response, but they offer high sensitivity, and high accuracy for measuring small accelerations. In a system according to the proposal, a conventional accelerometer would be used to perform short-term measurements of higher-frequency components of acceleration, while an AIA would be used to provide consistent calibration of, and correction of errors in, the measurements of the conventional accelerometer in the lower-frequency range over the long term. A brief description of an AIA is prerequisite to a meaningful description of a system according to the proposal. An AIA includes a retroreflector next to one end of a cell that contains a cold cloud of atoms in an ultrahigh vacuum. The atoms in the cloud are in free fall. The retroreflector is mounted on the object, the acceleration of which is to be measured. Raman laser beams are directed through the cell from the end opposite the retroreflector, then pass back through the cell after striking the retroreflector. The Raman laser beams together with the cold atoms measure the relative acceleration, through the readout of the AIA, between the cold atoms and the retroreflector.

Maleki, Lute↗
NASA NTRS1980

Low thrust vehicle concept study

Low thrust chemical (hydrogen-oxygen) propulsion systems configured specifically for low acceleration orbit transfer of large space systems were defined. Results indicate that it is cost effective and least risk to combine the OTV and stowed spacecraft in a single 65 K Shuttle. The study shows that the engine for an optimized low thrust stage (1) does not require very low thrust; (2) 1-3 K thrust range appears optimum; (3) thrust transient is not a concern; (4) throttling probably not worthwhile; and (5) multiple thrusters complicate OTV/LSS design and aggravate LSS loads. Regarding the optimum vehicle for low acceleration missions, the single shuttle launch (LSS and expendable OTV) is most cost effective and least risky. Multiple shuttles increase diameter 20%. The space based radar structure short OTV (which maximizes space available for packaged LSS) favors use of torus tank. Propellant tank pressures/vapor residuals are little affected by engine thrust level or number of burns.

Source record↗
NASA NTRS2011

Dynamic Testing of the NASA Hypersonic Project Combined Cycle Engine Testbed for Mode Transition Experiments

NASA is interested in developing technology that leads to more routine, safe, and affordable access to space. Access to space using airbreathing propulsion systems has potential to meet these objectives based on Airbreathing Access to Space (AAS) system studies. To this end, the NASA Fundamental Aeronautics Program (FAP) Hypersonic Project is conducting fundamental research on a Turbine Based Combined Cycle (TBCC) propulsion system. The TBCC being studied considers a dual flow-path inlet system. One flow-path includes variable geometry to regulate airflow to a turbine engine cycle. The turbine cycle provides propulsion from take-off to supersonic flight. The second flow-path supports a dual-mode scramjet (DMSJ) cycle which would be initiated at supersonic speed to further accelerate the vehicle to hypersonic speed. For a TBCC propulsion system to accelerate a vehicle from supersonic to hypersonic speed, a critical enabling technology is the ability to safely and effectively transition from the turbine to the DMSJ-referred to as mode transition. To experimentally test methods of mode transition, a Combined Cycle Engine (CCE) Large-scale Inlet testbed was designed with two flow paths-a low speed flow-path sized for a turbine cycle and a high speed flow-path designed for a DMSJ. This testbed system is identified as the CCE Large-Scale Inlet for Mode Transition studies (CCE-LIMX). The test plan for the CCE-LIMX in the NASA Glenn Research Center (GRC) 10- by 10-ft Supersonic Wind Tunnel (10x10 SWT) is segmented into multiple phases. The first phase is a matrix of inlet characterization (IC) tests to evaluate the inlet performance and establish the mode transition schedule. The second phase is a matrix of dynamic system identification (SysID) experiments designed to support closed-loop control development at mode transition schedule operating points for the CCE-LIMX. The third phase includes a direct demonstration of controlled mode transition using a closed loop control system developed with the data obtained from the first two phases. Plans for a fourth phase include mode transition experiments with a turbine engine. This paper, focusing on the first two phases of experiments, presents developed operational and analysis tools for streamlined testing and data reduction procedures.

Source record↗
NASA NTRS2006

Engineering the LISA Project: Systems Engineering Challenges

The Laser Interferometer Space Antenna (LISA) is a joint NASA/ESA mission to detect and measure gravitational waves with periods from 1 s to 10000 s. The systems engineering challenges of developing a giant interferometer, 5 million kilometers on a side, an: numerous. Some of the key challenges are presented in this paper. The organizational challenges imposed by sharing the engineering function between three centers (ESA ESTEC, NASA GSFC, and JPL) across nine time zones are addressed. The issues and approaches to allocation of the acceleration noise and measurement sensitivity budget terms across a traditionally decomposed system are discussed. Additionally, using LISA to detect gravitational waves for the first time presents significant data analysis challenges, many of which drive the project system design. The approach to understanding the implications of science data analysis on the system is also addressed.

systems engineering↗
NASA NTRS1992

Propulsion system performance resulting from an Integrated Flight/Propulsion Control design

Propulsion system specific results are presented from the application of the Integrated Methodology for Propulsion and Airframe Control (IMPAC) design approach to Integrated Flight/Propulsion Control design for a STOVL aircraft in transition flight. The IMPAC method is briefly discussed and the propulsion system specifications for the integrated control design are examined. The structure of a linear engine controller that results from partitioning a linear centralized controller is discussed. The details of a nonlinear propulsion control system are presented, including a scheme to protect the engine operational limits: the fan surge margin and the acceleration/deceleration schedule which limits the fuel flow. Also, a simple but effective multivariable integrator windup protection scheme is investigated. Nonlinear closed-loop simulation results are presented for two typical pilot commands for transition flight: acceleration while maintaining flight path angle and a change in flight path angle while maintaining airspeed. The simulation nonlinearities include the airframe/engine coupling, the actuator and sensor dynamics and limits, the protection scheme for the engine operational limits, and the integrator windup protection. Satisfactory performance of the total airframe plus engine system for transition flight, as defined by the specifications, is maintained during the limit operation of the closed-loop engine subsystem.

Mattern, Duane↗
NASA NTRS1971

A method for determining the response of space shuttle to atmospheric turbulence. Volume 1: Space shuttle turbulence response

A computer program has been developed and demonstrated that can analyze the response of space shuttle to atmospheric turbulence. The method developed accounts for propellant slosh, gimballed engine, and stability augmentation system (SAS) coupling with the elastic vehicle. Statistical outputs are generated that relate vehicle loads and accelerations to level of random turbulence. For discrete turbulence descriptions, response time-histories are computed. Preliminary turbulence response analyses of space shuttle were conducted for one ascent and one booster flyback subsonic flight condition. The ascent case considered both symmetric and antisymmetric boundary conditions, while only the symmetric analysis was conducted for booster flyback. The three conditions were analyzed with SAS active and inactive, but apparent instabilities with SAS active (arising from improper gains) invalidated the results. Load and acceleration responses in all cases, however, were well within vehicle design limits.

Source record↗
NASA NTRS1976

Teledyne Continental Motors emissions data and analysis and flight test results

Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.

Rezy, B. J.↗
NASA NTRS1990

Microgravity liquid propellant management

The requirement to settle or to position liquid fluid over the outlet end of a spacecraft propellant tank prior to main engine restart, poses a microgravity fluid behavior problem. Resettlement or reorientation of liquid propellant can be accomplished by providing optimal acceleration to the spacecraft such that the propellant is reoriented over the tank outlet without any vapor entrainment, any excessive geysering, or any other undersirable fluid motion for the space fluid management under microgravity environment. The most efficient technique is studied for propellant resettling through the minimization of propellant usage and weight penalties. Both full scale and subscale liquid propellant tank of Space Transfer Vehicle were used to simulate flow profiles for liquid hydrogen reorientation over the tank outlet. In subscale simulation, both constant and impulsive resettling acceleration were used to simulate the liquid flow reorientation. Comparisons between the constant reverse gravity acceleration and impulsive reverse gravity acceleration to be used for activation of propellant resettlement shows that impulsive reverse gravity thrust is superior to constant reverse gravity thrust.

Hung, R. J.↗
NASA NTRS1999

Piloted Simulation Study of a Dual Thrust-Cutback Procedure for Reducing High-Speed Civil Transport Takeoff Noise Levels

A piloted simulation study was performed for the purpose of indicating the noise reduction benefits and piloting performance that could occur for a typical 4-engine high-Speed Civil Transport (HSCT) configuration during takeoff when a dual thrust-cutback procedure was employed with throttle operation under direct computer control. Two thrust cutbacks were employed with the first cutback performed while the vehicle was accelerating on the run-way and the second cutback performed at a distance farther downrange. Added vehicle performance improvements included the incorporation of high-lift increments into the aerodynamic database of the vehicle and the use of limited engine oversizing. Four single-stream turbine bypass engines that had no noise suppression of any kind were used with this configuration. This approach permitted establishing the additional noise suppression level that was needed to meet Federal Air Regulation Part 36 Stage 3 noise levels for subsonic commercial jet aircraft. Noise level results were calculated with the jet mixing and shock noise modules of the Aircraft Noise Prediction Program (ANOPP).

Riley, Donald R.↗
NASA NTRS2008

MODSIM World 2007 Conference and Expo: Select Papers and Presentations from the Education and Training Track

This NASA Conference Publication features select papers and PowerPoint presentations from the Education and Training Track of MODSIM World 2007 Conference and Expo. Invited speakers and panelists of national and international renown, representing academia, industry and government, discussed how modeling and simulation (M&S) technology can be used to accelerate learning in the K-16 classroom, especially when using M&S technology as a tool for integrating science, technology, engineering and mathematics (STEM) classes. The presenters also addressed the application ofM&S technology to learning and training outside of the classroom. Specific sub-topics of the presentations included: learning theory; curriculum development; professional development; tools/user applications; implementation/infrastructure/issues; and workforce development. There was a session devoted to student M&S competitions in Virginia too, as well as a poster session.

Pinelli, Thomas E.↗
NASA NTRSDate not supplied

Maturation of In-space Welding in Reduced Gravity and Reduced Pressure Environments Through Progression to Suborbital Flight Experiments

Development of in-space welding (ISW) is a key and enabling manufacturing technology as welding is currently involved in producing approximately 90% of durable goods, and this trend is expected to hold for in-space manufacturing as well. ISW is critical to a sustainable space economy. To mature in-space welding, numerous gaps must be closed since NASA has not made a weld in space in 50 years. Advancing laser beam welding (LBW) towards a suborbital flight demonstration will help mature the process for in-space assembly & manufacturing (ISAM) through demonstration in relevant environments and achieving technology readiness milestones. LBW technologies and science improved by this work will benefit in-space manufacturing, long-term sustainability of space structures & operations, and the overall space economy. Ground-based welding of aerospace hardware requires an Edisonian approach to qualify a welding process; however, this approach is infeasible for ISW qualification due to mass, volume, logistic, and cost challenges inherent to the space environment. To address this challenge, we are conducting ground and suborbital tests with partners performing parabolic flights to gather data on LBW processes and infuse them into NASA & partner missions. This progression from ground to flight experiments will elucidate relevant physics during LBW: 1) reduced gravity, 2) reduced pressure, and 3) extreme temperature. Data from post-flight evaluation and in situ instrumentation will feed integrated computational materials engineering (ICME) tools to reduce the burden of ISW infusion by establishing a link between space and terrestrial environments, ultimately accelerating the qualification of LBW in space.

in-space welding↗
NASA NTRS1994

Lunar missions using advanced chemical propulsion: System design issues

To provide the transportation of lunar base elements to the moon, large high-energy propulsion systems will be required. Advanced propulsion systems for lunar missions can provide significant launch mass reductions and payload increases. These mass reductions and added payload masses can be translated into significant launch cost savings for the lunar base missions. The masses in low Earth orbit (LEO) were compared for several propulsion systems: nitrogen tetroxide/monomethyl hydrazine (NTO/MMH), oxygen/methane (O2/CH4), oxygen/hydrogen (O2/H2), and metallized O2/H2/Al propellants. Also, the payload mass increases enabled with O2/H2 and O2/H2/Al systems were addressed. In addition, many system design issues involving the engine thrust levels, engine commonality between the transfer vehicle and the excursion vehicle, and the number of launches to place the lunar mission vehicles into LEO will be discussed. Analyses of small lunar missions launched from a single STS-C flight are also presented.

TRT-THEORETICAL↗
NASA NTRS2019

A Realistic Roadmap to Formation Flying Space Interferometry

The ultimate astronomical observatory would be a formation flying interferometer in space, immune to atmospheric turbulence and absorption, free from atmospheric and telescope thermal emission, and reconfigurable to adjust baselines according to the required angular resolution. Imagine the near/mid-infrared sensitivity of the JWST and the far-IR sensitivity of Herschel but with ALMA-level angular resolution, or imagine having the precision control to null host star light across 250m baselines and to detect molecules from the atmospheres of nearby exo-Earths. With no practical engineering limit to the formation’s size or number of telescopes in the array, formation flying interferometry will revolutionize astronomy and this White Paper makes the case that it is now time to accelerate investments in this technological area. Here we provide a brief overview of the required technologies needed to allow light to be collected and interfered using separate spacecrafts. We emphasize the emerging role of inexpensive smallSat projects and the excitement for the LISA Gravitational Wave Interferometer to push development of the required engineering building-blocks. We urge the Astro2020 Decadal Survey Committee to highlight the need for a small-scale formation flying space interferometer project to demonstrate end-to-end competency with a timeline for first stellar fringes by the end of the decade.

Gioia Rau↗
NASA NTRS1989

Innovative pylon concepts for engine-airframe integration for transonic transports

Pylon cross-sectional geometries that are believed to reduce pylon/wing installation drag are analyzed. The basic design philosophy is to alleviate flow acceleration near the pylon/wing junction by aerodynamic means. This involves reshaping the pylon, particularly on the inboard side. In some instances this is achieved by moving the pylon trailing edge closure aft of the wing trailing edge. A three-dimensional Euler code was used for the analysis. Promising pylon shapes are identified for further investigation.

Naik, Dinesh A.↗
NASA NTRS1990

An optical technique to measure ion engine grid distortion due to differential thermal expansion

This paper describes an optical technique developed for measuring small differential grid displacements due to thermal expansion of an ion thruster accelerator system. The technique is based on confocal scanning optical microscope type II. For the measurements of small displacements where there are distances on the order of a meter or more between the lens plane and the sample, some of the optical components are moved while the sample is kept fixed. The feasibility of applying this technique to measure the thermally induced ion thruster grid displacements was demonstrated in a bench-top simulation. It is noted that this technique can also provide information on grid movement resulting from thermal transients such as the start-up.

Trava-Airoldi, V. J.↗