Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Full-coverage film cooling on flat, isothermal surfaces: Data and predictions

The heat transfer and fluid mechanics characteristics of full-coverage film cooling were investigated. The results for flat, isothermal plates for three injection geometries (normal, slant, and compound angle) are summarized and data concerning the spanwise distribution of the heat transfer coefficient within the blowing region are presented. Data are also presented for two different numbers of rows of holes (6 and 11). The experimental results summarized can be predicted with a two dimensional boundary layer code, STANCOOL, by providing descriptors of the injection parameters as inputs.

Crawford, M. E.↗
NASA NTRS1980

Effects of various assumptions on the calculated liquid fraction in isentropic saturated equilibrium expansions

The saturated equilibrium expansion approximation for two phase flow often involves ideal-gas and latent-heat assumptions to simplify the solution procedure. This approach is well documented by Wegener and Mack and works best at low pressures where deviations from ideal-gas behavior are small. A thermodynamic expression for liquid mass fraction that is decoupled from the equations of fluid mechanics is used to compare the effects of the various assumptions on nitrogen-gas saturated equilibrium expansion flow starting at 8.81 atm, 2.99 atm, and 0.45 atm, which are conditions representative of transonic cryogenic wind tunnels. For the highest pressure case, the entire set of ideal-gas and latent-heat assumptions are shown to be in error by 62 percent for the values of heat capacity and latent heat. An approximation of the exact, real-gas expression is also developed using a constant, two phase isentropic expansion coefficient which results in an error of only 2 percent for the high pressure case.

Bursik, J. W.↗
NASA NTRS1979

Effect of grazing flow on the nonlinear acoustic behavior of helmholtz resonators

A semi empirical fluid mechanical model is derived of the acoustic behavior of thin walled single orifice Helmholtz resonators in a grazing flow environment. The model assumes that the flow field incident to a resonator orifice consists of a spherical sound particle velocity field superimposed upon a mean grazing flow. The incident and cavity sound fields are connected in terms of an orifice discharge coefficient whose values are determined experimentally using the two microphone method. With regard to its application to rocket motor interiors, the most important finding of this study is that the acoustic impedance of Helmholtz resonators is affected by grazing flow when the product of the amplitude of the sound pressure incident to the resonator orifice and the rocket motor interior mean grazing flow speed are less than 0.5. For values greater than 0.5, the acoustic impedance is independent of the grazing flow.

Hersh, A. S.↗
NASA NTRS1980

Theory of the low-latitude boundary layer

A one-dimensional steady state fluid mechanical model is developed of the low-latitude plasma boundary layer inside the dawn and dusk magnetopause. Momentum transfer in the layer is produced by viscosity and/or mass diffusion. Coupling to the ionosphere is achieved via field-aligned currents, the magnitude of which is limited by parallel potential drops. These currents flow into and out of the ionosphere in the manner described by Iijima and Potemra. The higher-latitude (region 1) currents are associated with the boundary layer proper, while the lower-latitude (region 2) ones are associated with a region of sunward return flow adjacent to the boundary layer. The parallel potential drops have a magnitude of typically 2-3 kV and a north-south extent of 100-200 km. The calculated potential profile corresponds reasonably well to observed inverted V precipitation events.

Sonnerup, B. U. OE.↗
NASA NTRS1979

Continuous high-power gas lasers

High power gas laser concepts are discussed with emphasis on the role that fluid mechanics has played in their development. Consideration is given to three types of systems: gasdynamic lasers, HF supersonic diffusion lasers, and electric discharge lasers. Flow effects and aerodynamic windows in such lasers are briefly described. Future directions of research are outlined.

Hertzberg, A.↗
NASA NTRS1980

Numerical grid generation techniques

The state of the art in topology and flow geometry is presented. Solution techniques for partial differential equations are reviewed and included developments in coordinate transformations, conformal mapping, and invariant imbeddings. Applications of these techniques in fluid mechanics, flow geometry, boundary value problems, and fluidics are presented.

Source record↗
NASA NTRS1980

Grid generation using classical techniques

A brief historical review of conformal mapping and its applications to problems in fluid mechanics and electromagnetism is presented. The use of conformal mapping as a grid generator is described. The philosophy of the 'closed form' approach and its application to a Neumann problem is discussed. Karman-Trefftz mappings and grids for ablated, three dimensional bodies are also discussed.

Moretti, G.↗
NASA NTRS1980

Grid and metric generation on the assembly of locally bi-quadratic coordinate transformations

The generation of metric coefficients of the coordinate transformation from a generally curved-sided domain boundary to the unit square (cube) is required for efficient solution algorithms in computational fluid mechanics. An algebraic procedure is presented for establishment of these data on the union of arbitrarily selected sub-domains of the global solution domain. A uniformly smooth progression of grid refinement is readily generated, including multiple specification of refined grids for a given macro-element domain discretization. The procedure is illustrated as generally applicable to non-simply connected domains in two and three dimensions.

Baker, A. J.↗
NASA NTRS1980

Application of optical methods to the study of jet noise and turbulence

Optical methods are generally applied in fluid mechanics for either visualization or measurement. The use of a laser anemometer to study flow velocity in a jet and its relaton to the sound radiated is described. The same acoustic emission phenomenon is also measued by combining the signals from four Schlieren systems with that from an interferometer. The use of an optical Fourier transformation approach with real time analysis to determine the spatio-temporal structure of a field of mass volume such as a waveguide or free jet is also examined.

Sava, P. G.↗
NASA NTRS1981

Statistical analysis of atmospheric turbulence about a simulated block building

An array of towers instrumented to measure the three components of wind speed was used to study atmospheric flow about a simulated block building. Two-point spacetime correlations of the longitudinal velocity component were computed along with two-point spatial correlations. These correlations are in good agreement with fundamental concepts of fluid mechanics. The two-point spatial correlations computed directly were compared with correlations predicted by Taylor's hypothesis and excellent agreement was obtained at the higher levels which were out of the building influence. The correlations fall off significantly in the building wake but recover beyond the wake to essentially the same values in the undisturbed, higher regions.

Steely, S. L., Jr.↗
NASA NTRS1980

Fluid dynamics of the unsteady two phase processes leading to DDT in granular solid propellants

Deflagration to Detonation (DDT) was predicted to occur in porous beds of high-energy solid propellants by solving the unsteady fluid mechanical convective heat transfer from hot gas products, obtained from the rapid burning at high pressures, provides the impetus to develop a narrow combustion zone and a resulting strong shock. A parametric study clearly indicates that DDT occurs only when a combination of the solids loading fraction, the burning rate constants, the propellant chemical energy, and the particle size provide for critical energy and gas release to support a detonation wave. Predictions for the run-up length to detonation as a function of these parameters are presented.

Krier, H.↗
NASA NTRS1980

Fundamental heat transfer research for gas turbine engines

Thirty-seven experts from industry and the universities joined 24 NASA Lewis staff members in an exchange of ideas on trends in aeropropulsion research and technology, basic analyses, computational analyses, basic experiments, near-engine environment experiments, fundamental fluid mechanics and heat transfer, and hot technology as related to gas turbine engines. The workshop proceedings described include pre-workshop input from participants, presentations of current activity by the Lewis staff, reports of the four working groups, and a workshop summary.

Metzger, D. E.↗
NASA NTRS1981

The choice of numerical boundary conditions for hyperbolic systems

Two fundamental problems for mixed initial boundary value problems with applications in fluid mechanics are discussed. First, different stability properties are discussed which are of importance for long time integrations and steady state calculations. Secondly, a new numerical technique for problems with an artificial boundary is introduced.

Gustafson, B.↗
NASA NTRS1981

Boundary-layer analysis for the convection/diffusion transition in dendritic growth

The supercooling dependence of dendritic growth kinetics under the influence of convective heat transport is investigated theoretically and experimentally with emphasis on theoretical prediction of the supercooling level at which the transition from diffusion-controlled to convection-controlled dendritic growth occurs. It is shown that the crossover between diffusive and convective transport depends on the relative thickness of the Stefan length compared with the thermal boundary layer. These lengths become equal at a supercooling which may be calculated from diffusion theory and fluid mechanics. It is also shown that the crossover supercooling varies weakly with the gravitational acceleration, melt viscosity, and the volumetric expansion coefficient.

Glicksman, M. E.↗
NASA NTRS1981

Optimal time splitting for two- and three-dimensional Navier-Stokes equations with mixed derivatives

A new explicit, time splitting algorithm has been developed for finite difference modelling of the full two and three-dimensional time-dependent, compressible, viscous Navier-Stokes equations of fluid mechanics. The scheme is optimal in the sense that the split operators achieve their maximum allowable time step, i.e., the corresponding Courant number. The algorithm allows a conservation-form formulation. Stability is proven analytically and verified numerically. In proving stability it was shown that all nine matrix coefficients of the Navier-Stokes equations are simultaneously symmetrizable by a similarity transformation. Two such transformations and their resulting symmetric matrix coefficients are presented explicitly.

Abarbanel, S.↗
NASA NTRS1981

Calculation of three-dimensional, inviscid, supersonic, steady flows

A detailed description of a computational program for the evaluation of three dimensional supersonic, inviscid, steady flow past airplanes is presented. Emphasis was put on how a powerful, automatic mapping technique is coupled to the fluid mechanical analysis. Each of the three constituents of the analysis (body geometry, mapping technique, and gas dynamical effects) was carefully coded and described. Results of computations based on sample geometrics and discussions are also presented.

Moretti, G.↗
NASA NTRS1982

Investigation of soot and carbon formation in small gas turbine combustors

An investigation of hardware configurations which attempt to minimize carbon and soot-production without sacrificing performance in small gas turbine combustors was conducted. Four fuel injectors, employing either airblast atomization, pressure atomization, or fuel vaporization techniques were combined with nozzle air swirlers and injector sheaths. Eight configurations were screened at sea-level takeoff and idle test conditions. Selected configurations were focused upon in an attempt to quantify the influence of combustor pressure, inlet temperature, primary zone operation, and combustor loading on soot and carbon formation. Cycle tests were also performed. It was found that smoke emission levels depended on the combustor fluid mechanics, the atomization quality of the injector and the fuel hydrogen content.

Rosfjord, T. J.↗
NASA NTRS1982

Flow process in combustors

Fluid mechanical effects on combustion processes in steady flow combustors, especially gas turbine combustors were investigated. Flow features of most interest were vorticity, especially swirl, and turbulence. Theoretical analyses, numerical calculations, and experiments were performed. The theoretical and numerical work focused on noncombusting flows, while the experimental work consisted of both reacting and nonreacting flow studies. An experimental data set, e.g., velocity, temperature and composition, was developed for a swirl flow combustor for use by combustion modelers for development and validation work.

Gouldin, F. C.↗