SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An investigation with special reference to auto rotation and spinning was conducted in two wind tunnels and in flight to find the aerodynamic effects of adding a sharp leading edge to a wing sector.
Tests were made on a model wing with three different sized split trailing-edged flaps, in the NACA 7 by 10 foot wind tunnel. The flaps were formed of the lower rear portion of the wing and were rotated downward about axes at their front edges. The lift, drag, and center of pressure were measured with the axis in its original position and also with it moved back in even steps to the trailing edge of the main wing, giving in effect an increase in area. The split flaps when deflected about their original axis locations gave slightly higher maximum lift coefficients than conventional trailing-edge flaps, and the lift coefficients were increased still further by moving the axes toward the rear. The highest value of C(sub L max), which was obtained with the largest flap hinged at 90 per cent of the chord from the leading edge, was 2.52 as compared with 1.27 for the basic wing.
Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested.
Tests were made with ordinary flap-type ailerons on two wings with different amounts of taper, one medium and the other extreme. On each wing both medium sized tapered ailerons and short wide tapered ailerons were tested.
Results are given of a series of systemic tests comparing lateral control devices with particular reference to their effectiveness at high angles of attack. These tests were made with two sizes of ordinary ailerons and different sizes of spoilers on a Clark Y wing model having a narrow auxiliary airfoil fixed ahead and above the leading edge, the chords of the main and auxiliary airfoils being parallel. In addition, the auxiliary airfoil itself was given angular deflection. The purpose was to provide rolling moments for lateral control. The tests were made in a 7 by 10 foot wind tunnel. They included both force and rotation tests to show the effect of the devices on the lift and drag characteristics of the wing and on the lateral stability characteristics, as well as lateral control. They showed that none of the aileron arrangements tried would give rolling control of an assumed satisfactory value at all angles of attack up to the stall. However, they would give satisfactory values, but at the expense of abnormally high deflections and very heavy hinge moments. The most effective combination of ailerons and spoilers gave satisfactory values of rolling moment at angles of attack below the stall, and the values did not fall off as rapidly above the stall as with ailerons alone. With an arrangement of this type having the proper relative proportions and linkage, it should be possible to obtain reasonably satisfactory yawing moments and control forces. Deflecting one-half of the auxiliary airfoil downward for the purpose of control gave strong favorable yawing moments at all angles of attack, but gave very small rolling moments at the low angles of attack.
Discussed here are a series of systematic tests being conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present tests were made with six different forms of floating tip ailerons of symmetrical section. The tests showed the effect of the various ailerons on the general performance characteristics of the wing, and on the lateral controllability and stability characteristics. In addition, the hinge moments were measured for the most interesting cases. The results are compared with those for a rectangular wing with ordinary ailerons and also with those for a rectangular wing having full-chord floating tip ailerons. Practically all the floating tip ailerons gave satisfactory rolling moments at all angles of attack and at the same time gave no adverse yawing moments of appreciable magnitude. The general performance characteristics with the floating tip ailerons, however, were relatively poor, especially the rate of climb. None of the floating tip ailerons entirely eliminated the auto rotational moments at angles of attack above the stall, but all of them gave lower moments than a plain wing. Some of the floating ailerons fluttered if given sufficiently large deflection, but this could have been eliminated by moving the hinge axis of the ailerons forward. Considering all points including hinge moments, the floating tip ailerons on the wing with 5:1 taper are probably the best of those which were tested.
Wind tunnel tests were made of a model wing having an aspect ratio of 3 and a tapered plan form with a straight trailing edge. The model had the Clark Y airfoil section throughout it's entire span and had no washout, depending on a trailing-edge flap for longitudinal balance and control. The flap had a constant chord and was divided into four equal portions along the span. The tests were made with the entire flap deflected to obtain longitudinal control and balance, and also with the inner portions deflected alone, and with the outer portions deflected alone. It was found that the simple wing with no washout or change of basic section along the span has aerodynamic characteristics well suited for use on tailless airplanes. A higher lift coefficient was obtained with the full-span flap deflected as a unit to give longitudinal balance than was obtained with either the inner or the outer portions of the flap deflected.
An investigation of the undesirable delayed action, or lag, of the spoiler-type lateral control device led to the development of the NACA slot-lip aileron. The tests were made in the 7- by 10-foot wind tunnel with a 4- by 8-foot wing hinged at the tunnel jet boundary and taken of the motion of the control device under test and of the resulting wing motion. First, the lag, as affected by the fore-and-aft location of retractable ailerons or spoilers was determined. The lag was found to increase regularly as the spoiler was moved from the rear of the wing toward the front. Then a combination of spoilers and fixed slot was developed that, with the spoiler retracting into the forward part of the slot, reduced the time lag to a negligible value. In addition, an arrangement was developed using a hinged aileron-type flap as the upper portion, or lip, of a slot through the wing. This arrangement appears to be usable as a form of lateral control device that shows promise of giving improved control and stability at the high angles of attack through stall, with negligible lag, low control forces, and relatively simple construction.
Preliminary tests have been made for the purpose of obtaining a flap arrangement suitable for direct and immediate control of the steepness of the glide path of an airplane, a use for which present flaps are not satisfactory. An attempt has been made to develop a flap giving a reasonably high maximum lift coefficient with relatively low deflection and maintaining this value of the maximum lift coefficient with a large increase of deflection, the increase in deflection being accompanied by a large increase in drag. An arrangement was found that gave a maximum lift coefficient of approximately 1.90 for all flap deflections between 25 and 80 degrees, within which range the drag of the wing increased regularly to a large value.
The distribution of the fuel among the various cylinders of a Pratt and Whitney 1340 S1H1-G engine was determined by chemically analyzing samples of exhaust gas from each cylinder. The engine was operated in the 20-foot wind tunnel at different power outputs, specific fuel consumptions, and engine speeds. The results showed that the variation in the quality of the mixture among the different cylinders was approximately 4 percent and was independent of power output, specific fuel consumption, and engine speed. The results also showed that the top cylinders operated with a lower air-fuel ratio than the bottom cylinders.
About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees fahrenheit. Columbium-treated and molybdenum-treated 18:8 steel exhibited improved stability over a wide range of temperatures. Tie rods of either material could be heated 30 minutes with safety at any temperature up to 1000 degrees Fahrenheit. At this temperature most of the residual stress would be relieved.
An investigation was made to determine the effect of mixture strength and of normal as well as optimum spark timing on the combustion, on the cylinder temperature, and on the performance characteristics of an engine. A single-cylinder test unit utilizing an air-cooled cylinder and a carburetor and operating with gasoline having an octane rating of 92 was used. The investigation covered a range of fuel-air ratios from 0.053 to 0.118. Indicator diagrams and engine-performance data were taken for each change in engine conditions. Examination of the indicator shows that for fuel-air ratios less than and greater than 0.082 the rate and the amount of effective fuel burned decreased. For a fuel-air ratio of 0.118 the combustion efficiency was only 58 percent. Advancing the spark timing increased the rate of pressure rise. This effect was more pronounced with leaner mixtures.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.