SEARCH · Search NASA

Results for “Fast reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Ion Cyclotron Heating in a Levitated Dipole Fusion Reactor

OpenStar Technologies is pursuing the levitated dipole (LD) as a highly modular, loosely-coupled system that leverages their expertise in high temperature superconductor (HTS) technology. The next generation experiment at OpenStar, Tahi (Ma¯ori for “first”), will demonstrate the generation and confinement of fast ions in a levitated dipole for the first time. Ion cyclotron range of frequency (ICRF) heating is a leading candidate for energetic ion formation in Tahi. A frequency in the 10 MHz range will be used for H minority heating or D majority heating with waves launched from an antenna located above the floating coil. Unlike a tokamak, where the targeted cyclotron resonance is typically a vertical path through the center of the plasma, in a dipole the resonance location follows a C-shaped path from the separatrix to the center of the plasma. The value of B also varies significantly within the confined plasma resulting in a large number of cyclotron harmonics present in the low field region. Furthermore, levitated dipoles contain a “first closed flux surface” surrounding the floating coil, in addition to the traditional separatrix /last closed flux surface. Simulation e ff orts using full-wave ICRF codes show that ICRF heating of a levitated dipole reactor is feasible using a pair of toroidal current straps phased to launch the appropriate parallel ( i.e. poloidal) refractive index.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Advanced Test Reactor Neutron Dosimetry Report - 173B

Results of neutron dosimetry measurements in ATR for cycle 173B-1&2 are presented. Cobalt and nickel wires were installed in numerous irradiation locations for the duration of the cycle. The specific activity of these wire segments can be used in conjunction with the presented cycle history information to determine the thermal- and fast-neutron fluence rates for each irradiation position during the cycle using the referenced standard test methods.

173B↗

DOE OSTI2025

Results of Neutron Dosimetry Measurements for the Advanced Test Reactor Cycle 173-C

Results of neutron dosimetry measurements in ATR for cycle 173-C are presented. Cobalt and nickel wires were installed in numerous irradiation locations for the duration of the cycle. The specific activity of these wire segments can be used in conjunction with the presented cycle history information to determine the thermal- and fast-neutron fluence rates for each irradiation position during the cycle using the referenced standard test methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane

Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)─ produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.

09 BIOMASS FUELS↗

DOE OSTI2024

Applicability of alkali beam emission spectroscopy on NSTX-U

Understanding fast pedestal dynamics and turbulent transport in the edge and scrape-off layer (SOL) plasma of spherical tokamaks is crucial for the design and operation of future fusion reactors. The alkali beam emission spectroscopy diagnostic technique offers a means to measure the absolute electron density radial profile and fluctuation amplitude in these regions. Here, in this study, we demonstrate that injecting a sodium neutral beam radially into the plasma and analyzing the light emission from its 3p–3s atomic transition using near-orthogonal viewing angles allows for accurate measurement of the electron density profile and fluctuations in the National Spherical Torus Experiment (NSTX) Upgrade spherical tokamak. Our findings indicate a peak signal-to-noise ratio of 118 in the pedestal and 12 in the SOL under typical NSTX plasma conditions. The spatial resolution for the electron density profile is estimated to be between 2 and 8 mm, while for fluctuation measurements, it ranges from 12 to 15 mm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Final CRADA Report – NFE-21-08693

TAE Technologies is developing a magnetic fusion energy concept known as the beam-driven field-reversed configuration (FRC) with the ultimate goal of developing a reactor for commercial electricity production capable of burning aneutronic pB11 fuel. To achieve the high plasma temperatures this requires, auxiliary radiofrequency (RF) heating will likely be needed. High Harmonic Fast Wave (HHFW) heating has been identified as a candidate RF heating scheme to overcome the unique challenges posed to RF heating by the FRC, including the large distance from the plasma edge to the last closed flux surface and a magnetic field profile with strength decreasing from edge to core and reversing sign at a null point inside the plasma. The purpose of this project was to develop the experimental capabilities to test HHFW on TAE’s C-2W device through the design of a phased array antenna and accompanying matching network. The design was performed by ORNL and informed by experiments with a prototype four-strap phased antenna-array that was manufactured and installed on the LArge Plasma Device (LAPD) at UCLA and simulations conducted with the Petra-M code under the purview of a previous INFUSE grant. The ORNL team completed the conceptual design of the antenna and matching network which was then handed off to the TAE Mechanical Design team. The design was then iterated on to ensure changes to the mechanical design did not interfere with the RF performance. This process is now complete, and, with mechanical design in hand, TAE is proceeding with plans for final integration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Reviewing Incident Neutron Energy assignments in 238 U(n,f) Fission Yield Data

Fission yield evaluations rely not only on precise measurements, but also on clear documentation of experimental conditions especially the energy of incident neutrons inducing fission. In the EXFOR database, following the convention adopted in past evaluations, the incident neutron energy has traditionally been divided in only three energy groups: thermal, fast and 14 MeV. The information is stored in the EN-DUMMY field, which often serves as a placeholder in the presence of broad-spectrum or reactor-based sources. This work reviews 238 U(n,f) entries in EXFOR that use EN-DUMMY, identifying cases where better energy estimates can be made based on the original publications, facility characteristics, or reconstructed neutron spectra. We assign new cross-section-weighted average energies where possible. The revised independent and cumulative fission yield data are compiled for future use in model development and evaluation efforts.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Advanced Test Reactor Neutron Dosimetry Report - 173B (Rev. 1)

173B↗

NASA NTRS2002

The FRC Acceleration Space Thruster (FAST) Experiment

The objective of the FRC (Field Reversed Configuration) Acceleration Space Thruster (FAST) Experiment is to investigate the use of a repetitive FRC source as a thruster, specifically for an NEP (nuclear electric propulsion) system. The Field Reversed Configuration is a plasmoid with a closed poloidal field line structure, and has been extensively studied as a fusion reactor core. An FRC thruster works by repetitively producing FRCs and accelerating them to high velocity. An FRC thruster should be capable of I(sub sp)'s in the range of 5,000 - 25,000 seconds and efficiencies in the range of 60 - 80 %. In addition, they can have thrust densities as high as 10(exp 6) N/m2, and as they are inductively formed, they do not suffer from electrode erosion. The jet-power should be scalable from the low to the high power regime. The FAST experiment consists of a theta-pinch formation chamber, followed by an acceleration stage. Initially, we will produce and accelerate single FRCs. The initial focus of the experiment will be on the ionization, formation and acceleration of a single plasmoid, so as to determine the likely efficiency and I(sub sp). Subsequently, we will modify the device for repetitive burst-mode operation (5-10 shots). A variety of diagnostics are or will be available for this work, including a HeNe interferometer, high-speed cameras, and a Thomson-scattering system. The status of the experiment will be described.

Martin, Adam↗

DOE OSTI2024

Godiva IV Simulated Radiation Field Characterization and Variance Reduction

Godiva IV is a system comprised of highly enriched uranium alloyed with molybdenum in the form of fuel plate rings. The reactor, along with its predecessors, was designed with the unique ability to satisfy interests in the super-prompt-critical reactor operation space. Originally, the reactor was part of the Los Alamos Critical Experiments Facility (LACEF) at Technical Area-18 (TA-18). The radiation field around Godiva at this facility was well characterized and understood. As a fast neutron system, the neutron spectrum in and around Godiva was close to a Watt Fission spectrum. The Kiva where Godiva IV was located at LACEF was made of thin, sheet metal walls which did not contribute significantly to the neutron spectrum. Following the transition of LACEF to the National Critical Experiments and Research Center (NCERC) in Nevada, Godiva-IV was moved from TA-18 to the Device Assembly Facility (DAF) at the Nevada National Security Site (NNSS). Part of this move brought renewed interest in radiation field characterization. The new facility introduced significant changes to the environment surrounding Godiva, and preliminary foil irradiation results suggested that the room contribution to the neutron spectrum was significant. Unlike at TA-18, a large thermal neutron signature was added to the fast spectrum from Godiva due to significant room return. A primary goal due to the additional complexity that the room return adds to the Godiva IV radiation emission spectrum was the development of an efficient Monte Carlo N-Particle (MCNP) calculation capable of characterizing the neutron spectrum anywhere in the room around Godiva. A campaign of activation foil irradiations and analysis were completed to support the validation of the MCNP model. The modeling of these foils in MCNP can be easily done with a standard volumetric neutron flux tally. However, given the multitude of locations and reaction rates to be modeled, further steps must be taken to increase the efficiency of these calculations in MCNP. During this study, a benchmark model currently under development for Godiva IV was used. A qualitative assessment of the thermal neutron contributors was performed using spatial neutron distribution plots. Additional detail was added to the model based on the qualitative results showing the thermal spectrum’s large sensitivity to hydrogenous material. Neutron energy spectra was evaluated at discrete locations in the room around Godiva to quantify the relative contribution of various components. It was discovered that the concrete walls are the largest contributor to the thermal signature, with minor contributions from plastic components surrounding Godiva. Following these results, two different variance reduction techniques were implemented to improve the problem efficiency in these calculations. In the first approach, an F5 point detector tally was implemented in the standard Godiva IV criticality problem. The second approach involved a weight-window generator implementation with an F5 point detector tally in a fixed source problem. The weight window implementation reduced the runtime from 42739.55 minutes to 1803.34 minutes (computer time), compared to the F5 KCODE implementation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2026

AGR-5/6/7 Ceramography Report

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established in 2002 to conduct research and development on tri-structural isotropic (TRISO)-coated particle fuel for High Temperature Gas-cooled Reactors (HTGRs). All AGR irradiations have been completed: AGR-1 (Collin 2015), AGR-2 (Collin 2014), AGR-3/4 (Collin 2016) and AGR-5/6/7 (Pham 2021). The objectives of each program are presented in Figure 1.1. The purpose of the AGR-5/6/7 program was to provide a baseline fuel qualification data set to support licensing, deployment, and operation of HTGRs in the United States. To achieve these goals, the program includes fuel fabrication, irradiations of TRISO fuels and high-temperature materials, safety testing and post-irradiation examination (PIE), fuel performance modeling, and fission product (FP) transport (Sharp 2020). The AGR-5/6/7 work continues as a final irradiation program of the Advanced Reactor Technologies (ART) program, that began in February 2018 and ended in July 2020. The AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 effective full power days (EFPDs) (Stempien 2023), resulting in final burn-up values, on a per-compact basis, ranging from 5.66% to 15.26% fissions per initial heavy metal atom (FIMA), and fast fluence values ranging from 1.62×1025 n/m2 to 5.55×1025 n/m2 (E >0.18 MeV) (Stempien 2022)

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Advanced Test Reactor Neutron Dosimetry Report - Cycle 175A-1

Results of neutron dosimetry measurements in ATR for cycle 175A-1 are presented. A single set of cobalt and nickel wires were installed in numerous irradiation locations for the duration of the cycle. The specific activity of these wire segments can be used in conjunction with the presented cycle history information to determine the thermal- and fast-neutron fluence rates for each irradiation position during the cycle using the referenced standard test methods.

175A↗

DOE OSTI2026

Advanced Test Reactor Neutron Dosimetry Report - Cycle 175B-1

Results of neutron dosimetry measurements in ATR for cycle 175B-1 are presented. A single set of cobalt and nickel wires were installed in numerous irradiation locations for the duration of the cycle. The specific activity of these wire segments can be used in conjunction with the presented cycle history information to determine the thermal- and fast-neutron fluence rates for each irradiation position during the cycle using the referenced standard test methods.

175B↗

DOE OSTI2025

Advanced Test Reactor Neutron Dosimetry Report – 174 A & B

Results of neutron dosimetry measurements in ATR for cycle 174 A B are presented. Cobalt and nickel wires were installed in numerous irradiation locations for the duration of the cycle. The specific activity of these wire segments can be used in conjunction with the presented cycle history information to determine the thermal- and fast-neutron fluence rates for each irradiation position during the cycle using the referenced standard test methods.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Mechanical characterization of fine-grain dispersion-strengthened tungsten as a plasma facing material

Field-Assisted Sintering Technology (FAST) was used to produce fine-grained, dispersion-strengthened tungsten (W) materials. Investigated materials 4138, 4353, and 4355 composed of 3 wt% ZrC sintered at 1800 °C, 5 wt% ZrC sintered at 1800 °C, and 3 wt% ZrC sintered at 2000 °C, respectively. They were compared against ITER-grade W. A series of mechanical and thermal property testing and microstructure studies were conducted to study them as a potential plasma facing material (PFM) for fusion reactors. Hardness testing showed that manufacturing conditions substantially altered hardness. Material 4355 had an average HV10 value of 497.2 ± 16.8, slightly higher than ITER-grade at 378.5 ± 40.3. However, material 4353 was substantially higher with an HV10 value of 738.9 ± 31.7 over the investigated temperature range. Electron Backscatter Diffraction (EBSD) analysis showed that FAST produced substantially smaller grains than the hot-rolled ITER-grade W material, offering notable control over grain size. Materials 4353 and 4355 had grain sizes of 0.44 ± 0.20 µm and 3.67 ± 0.89 µm, respectively, whereas ITER-grade 27.14 ± 19.76 µm at room temperature. The fine grain structures showed no net coarsening after 1 hr. anneals up to 1800 °C, several hundred degrees above the 1100 – 1500 °C recrystallization range reported for conventional W. Inverse application of the Zener pinning relationship to the measured grain sizes indicates that these two FAST sintering conditions produce markedly different effective dispersoid populations, with effective particle diameters of approximately 90 nm at a peak sintering temperature of 1800 °C and approximately 460 nm at 2000 °C, respectively. This result demonstrates that the FAST thermal condition itself, and not the nominal ZrC content alone, governs the pinning effectiveness of the dispersion. Thermal diffusivity measurements support this finding independently. Materials of identical composition sintered at different temperatures differ by approximately 19% in measured thermal diffusivity with statistically indistinguishable density, while materials of different composition and sintering temperature converge to within approximately 2%. At a representative divertor heat flux of 10 MW/m², the lower thermal conductivity of the fine-grained materials corresponds to approximately 28 to 33 °C per millimeter of armor thickness relative to ITER-grade W, traded against a substantially larger margin to recrystallization-driven degradation. While high temperature tensile testing revealed likely contamination that motivates refinement of the manufacturing process, FAST-produced, fine-grained, dispersion-strengthened W offers process-controlled microstructural stability well above the operating temperatures of conventional W and supports its continued development as a PFM for economically viable commercial fusion power.

Parker, Gabe [ORNL] (ORCID:0000000190394100)↗

DOE OSTI2025

NuFast-LBL

NuFast is designed to calculate all nine neutrino oscillation probabilities in matter for long-baseline accelerator (e.g. NOvA, T2K, DUNE, HK) and reactor experiments (e.g. JUNO) very quickly, using the algorithms optimized for realistic oscillation scenarios. NuFast is provided in Fortran, C++, and Python, although no particular guarantees are made that the Python code is "fast".

Denton, PeterB. [Brookhaven National Laboratory (B↗

NASA NTRS2016

A Multi-Dimensional Heat Transfer Model of a Tie-Tube and Hexagonal Fuel Element for Nuclear Thermal Propulsion

The Space Capable Cryogenic Thermal Engine (SCCTE) effort considers a nuclear thermal rocket design based around a Low-Enriched Uranium (LEU) design fission reactor. The reactor core is comprised of bundled hexagonal fuel elements that directly heat hydrogen for expansion in a thrust chamber and hexagonal tie-tubes that house zirconium hydride moderator mass for the purpose of thermalizing fast neutrons resulting from fission events. Created 3D steady state Hex fuel rod model with 1D flow channels. Hand Calculation were used to set up initial conditions for fluid flow. The Hex Fuel rod uses 1D flow paths to model the channels using empirical correlations for heat transfer in a pipe. Created a 2-D axisymmetric transient to steady state model using the CFD turbulent flow and Heat Transfer module in COMSOL. This model was developed to find and understand the hydrogen flow that might effect the thermal gradients axially and at the end of the tie tube where the flow turns and enters an annulus. The Hex fuel rod and Tie tube models were made based on requirements given to us by CSNR and the SCCTE team. The models helped simplify and understand the physics and assumptions. Using pipe correlations reduced the complexity of the 3-D fuel rod model and is numerically more stable and computationally more time-efficient compared to the CFD approach. The 2-D axisymmetric tie tube model can be used as a reference "Virtual test model" for comparing and improving 3-D Models.

Gomez, C. F.↗

DOE OSTI2024

The Use of High-Density UN Fuel in Heat-Pipe Microreactors

Heat-pipe microreactors (HPMRs) are very small-scale nuclear reactors that employ heat pipes (HPs) for heat removal. HPMRs can be easily integrated with other forms of renewable energies, can be used for emergency responses to disaster relief zones, can be deployed in remote locations not connected to the grid, and can be removed from sites and replaced by new ones. HPMRs can also be used for space missions as HPs do not rely on gravity for heat transfer. Conventional fuel materials, such as uranium oxide (UO 2 ) and uranium oxycarbide (UCO), are currently considered in most existing HPMR designs, but ceramic uranium nitride (UN) fuel that has high uranium density, high thermal conductivity, and high melting point may become a better fuel candidate. Through neutronics calculations, this paper assesses the impact of using UN fuel in HPMRs with two different neutron spectra (fast and thermal) and two different fuel forms [traditional solid fuel pellets and TRi-structural-ISOtropic (TRISO) fuel compacts]. It was concluded that retrofitting HPMRs with UN fuel has the potential to reduce the initial 235 U enrichment requirement by ~3 wt% (to keep the same cycle length) or increase the cycle length (by keeping the same initial 235 U enrichment), which enables more compact and transportable HPMR core designs. However, using UN fuel decreases the control element worth [by up to 20% for the Special Purpose Reactor (SPR) and 5% for HP-MR] and is up to 80% more costly. Increasing 15 N enrichment can further decrease the initial 235 U enrichment requirement and increase the control element worth but is more costly. In conclusion, compared to fast-spectrum HPMRs fueled with solid pellet fuels, retrofitting UN fuel is more suitable for thermal-spectrum HPMRs fueled with TRISO fuel compacts, where the neutron spectrum hardening caused by using UN is less significant.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗