Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Essential effect of the electrolyte on the mechanical and chemical degradation of LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes upon long-term cycling

Capacity fading during long-term cycling (>1500×) is still a critical challenge for Li-ion batteries that use Ni-rich layered oxides, e.g. LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA), as the cathode. Microcracks have been previously recognized as one of the primary reasons for the observed capacity fade. Although there exists a generally developed mechanical understanding of microcracks, the role of the electrolyte has not been clearly understood, especially after extended cycling and at the atomic scale. Here, we unveil the microstructural evolution of spherical NCA secondary particles after long-term cycling using scanning transmission electron microscopy accompanied with electron energy loss spectroscopy. In this work, we found that the microcracks initiated and grew through grain boundaries, which then serve as the pathway for electrolyte penetration into secondary NCA particles. Additionally, the rock-salt phase reconstruction is prone to occur at the (003) surfaces of the primary particles or the crack surfaces, largely due to electrolyte (LiPF 6 EC/EMC) corrosion. Crack propagation within the NCA grains is primarily a joint consequence from electrolyte corrosion and mechanical strain during lithiation/delithiation. During extended cycling, due to the distinctive surface facets, the primary grains located in the center of the secondary particles experience more intensive electrolyte corrosion, leading to a reduced contact with nearby particles, impairing the overall capacity. These results establish the initiation and growth mechanism of microcracks and voids in NCA-based cathodes during cycling and point out the role of the electrolyte in affecting the degradation of NCA-based cathodes.

25 ENERGY STORAGE↗

Irradiation effects in rapidly and conventionally solidified alloys. Phase stability in rapidly solidified N i-Nb under Ni ion irradiation

Two alloy compositions in the Ni-Nb system (Ni60Nb40 and Ni85Nb15) were produced by rapidly quenching from the melt with the piston anvil technique. The Ni60Nb40 was transformed to a metastable, partially crystalline state by heat treatment in a differential scanning calorimeter. The Ni85Nb15 was fully crystalline, with the majority of the grains composed of collections of primary dendrite arms. Both compositions were irradiated with 4 MeV Ni++ ions. The irradiation induced microstructures were examined by transmission electron microscopy and compared with thermally aged samples. The thermal evolution was arrested by ion irradiation in the temperature range studied, by inhibiting the nucleation of the NiNb phase. No irradiation induced voids were observed. It is found that the ion irradiation drives the microstructure along a different path than thermal evolution.

Source record↗

Comparison of Ion and Neutron Irradiations to 3 dpa at 500 deg. C in Ferritic-Martensitic Alloys

The growing global demand for energy will increasingly call upon advanced nuclear fission reactors to supply safe and reliable electricity. The structural and fuel cladding components of these reactors will be subject to extreme conditions of irradiation damage up to several hundred displacements per atom (dpa) at temperatures as high as 700 deg. C. Ferritic-martensitic (F-M) steels are leading candidates for these challenging conditions due to their strength and dimensional stability under irradiation. In order to accelerate the process for evaluating F-M alloys, charged particles are increasingly being used to emulate neutron irradiations. Charged particle irradiations allow the possibility of conducting irradiation experiments within a shorter time period (i.e. at a rate up to 4 orders of magnitude faster) and with minimal radioactivation of the material, enabling lower cost and faster turnaround of post irradiation examination and analysis. However, the irradiation dose rate, damage cascade morphologies, and irradiation damage depth profiles all differ widely between protons, heavier ions, and neutrons. Currently, there is limited understanding of the significance of these physical differences and how they manifest in the irradiated microstructure and mechanical properties of F-M steels. The objective of this study is to evaluate charged particles as a surrogate for neutron irradiations in F-M alloys by assessing common irradiation conditions using Fe{sup ++} ions, protons, and neutrons. Keeping the temperature and dose consistent enables isolation of the effects of each irradiating particle and their respective dose rates and cascade morphologies. Specimens of HCM12A and HT9 were irradiated separately with protons, self-ions, and neutrons to a common dose of 3 dpa at 500 deg. C. The microstructure of each specimen was characterized with TEM and LEAP and compared to evaluate proton and self-ion irradiation as a surrogate for neutron irradiation at these conditions. - Proton, self-ion, and neutron irradiations produced consistent sizes and number densities of grains, carbides, dislocation lines, and dislocation loops. Voids were absent in all conditions. The charged particle irradiations have successfully reproduced the neutron irradiation results for these microstructural features without a temperature shift. - Nano-cluster evolution of Si-Mn-Ni-P and Cu-rich clusters was markedly different for each irradiating particle type. Some cluster morphology trends could be explained by differences in cascade volume for differing irradiating species. But dose rate likely also influences cluster evolution. - Cr-rich nanoclusters nucleated only in the neutron-irradiated HCM12A and HT9. This is likely due to thermal aging at 500 deg. C over a longer experimental time, as compared to the proton and self-ion irradiations. (authors)

36 MATERIALS SCIENCE↗

Effect of wheel speed and annealing temperature on microstructure and texture evolution of Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} ribbon

Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} magnetic shape memory alloy was successfully produced as preferentially textured ribbon by melting spinning with different wheel speed. X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) were used to study structure and texture evolution of these melt-spun ribbons. The thickness of melt-spun ribbon is 42 μm, 65 μm and 30 μm depending on wheel speed of 1 0 m/s, 15 m/s and 20 m/s, respectively. Density of α fiber texture (〈100〉//ND) vary with wheel speed changes, and is most intensive in the ribbon with wheel speed of 15 m/s. Grains of the ribbons grow after being annealed at 873 K, 973 K, 1073 K and 1173 K, recrystallization was not observed in ribbons after being annealed at 873 K but occurred in ribbons after being annealed at higher temperatures. The α fiber texture becomes weaker to some extent after annealing at different temperatures, due to new recrystallization texture formed at the process of annealing. - Highlights: •Sectional part of shape memory ribbon is firstly investigated by EBSD method. •Thickness and texture of ribbons vary with wheel speed. •Annealing temperature affect texture and microstructure evolution greatly. •Recrystallization textures were observed in ribbons after being annealed.

36 MATERIALS SCIENCE↗

Linking microstructural evolution and macro-scale friction behavior in metals [Predicting the friction behavior of metals using a microstructural evolution model]

A correlation is established between the macro-scale friction regimes of metals and a transition between two dominant atomistic mechanisms of deformation. Metals tend to exhibit bi-stable friction behavior—low and converging or high and diverging. These general trends in behavior are shown to be largely explained using a simplified model based on grain size evolution, as a function of contact stress and temperature, and are demonstrated for self-mated pure copper and gold sliding contacts. Specifically, the low-friction regime (where µ < 0.5) is linked to the formation of ultra-nanocrystalline surface films (10–20 nm), driving toward shear accommodation by grain boundary sliding. Above a critical combination of stress and temperature—demonstrated to be a material property—shear accommodation transitions to dislocation dominated plasticity and high friction, with µ > 0.5. We utilize a combination of experimental and computational methods to develop and validate the proposed structure–property relationship. As a result, this quantitative framework provides a shift from phenomenological to mechanistic and predictive fundamental understanding of friction for crystalline materials, including engineering alloys.

36 MATERIALS SCIENCE↗

Multi Resolution In-Situ Testing and Multiscale Simulation for Creep Fatigue Damage Analysis of Alloy 617

This report outlines the research activities that were carried out for the integrated experimental and simulation investigation of creep-fatigue damage mechanism and life prediction of Nickel-based alloy, Inconel 617 at high temperatures (950° and 850°). First, a novel experimental design using a hybrid control technique is proposed. The newly developed experimental technique can generate different combinations of creep and fatigue damage by changing the experimental design parameters. Next, detailed imaging analysis and statistical data analysis are performed to quantify the failure mechanisms of the creep fatigue of alloy 617 at high temperatures. It is observed that the creep damage is directly associated with the internal voids at the grain boundaries and the fatigue damage is directly related to the surface cracking. It is also observed that the classical time fraction approach does not has a good correlation with the experimental observed damage features. An effective time fraction parameter is seen to have an excellent correlation with the material microstructural damage. Thus, a new empirical damage interaction diagram is proposed based on the experimental observations. Following this, a macro level viscoplastic model coupled with damage is developed to simulate the stress/strain response under creep fatigue loadings. A damage rate function based on the hysteresis energy and creep energy is proposed to capture the softening behavior of the material and a good correlation with life prediction and material hysteresis behavior is observed. The simulation work is extended to include the microstructural heterogeneity. A crystal plasticity finite element model considering isothermal and large deformation conditions at the microstructural scale has been developed for fatigue, creep-fatigue as well as creep deformation and rupture at high temperature. The model considers collective dislocation glide and climb of the grains and progressive damage accumulation of the grain boundaries. The glide model incorporates a slip resistance evolution model that characterizes the solute-drag creep effects and can capture well the stress-strain and stress time response of fatigue and creep-fatigue tests at various strain ranges and hold times. In order to accurately capture the creep strains that accumulate particularly at relatively low stress levels, a dislocation climb model has been incorporated into the crystal plasticity modeling framework. The dislocation climb model parameters are calibrated and verified through experimental creep tests performed at 950°. In addition, a cohesive zone model has been fully implemented in the context of the crystal plasticity finite element model to capture the intergranular creep damage. The parameters of the cohesive zone model have been calibrated using available experimental data. The numerical simulations illustrate the capability of the proposed model in capturing damage initiation and growth under creep loads as compared to the experimental observations. The microscale analysis sheds light on the crack initiation sites and propagation patterns within the microstructure. The model is also utilized to investigate the hybrid-controlled creep-fatigue tests and has been found to capture reasonably well the stress-strain response with different hold times and hold stress magnitudes.

36 MATERIALS SCIENCE↗

Intrinsic stress in ZrN thin films: Evaluation of grain boundary contribution from in situ wafer curvature and ex situ x-ray diffraction techniques

Low-mobility materials, like transition metal nitrides, usually undergo large residual stress when sputter-deposited as thin films. While the origin of stress development has been an active area of research for high-mobility materials, atomistic processes are less understood for low-mobility systems. In the present work, the contribution of grain boundary to intrinsic stress in reactively magnetron-sputtered ZrN films is evaluated by combining in situ wafer curvature measurements, providing information on the overall biaxial stress, and ex situ x-ray diffraction, giving information on elastic strain (and related stress) inside crystallites. The thermal stress contribution was also determined from the in situ stress evolution during cooling down, after deposition was stopped. The stress data are correlated with variations in film microstructure and growth energetics, in the 0.13-0.42 Pa working pressure range investigated, and discussed based on existing stress models. At low pressure (high energetic bombardment conditions), a large compressive stress is observed due to atomic peening, which induces defects inside crystallites but also promotes incorporation of excess atoms in the grain boundary. Above 0.3-0.4 Pa, the adatom surface mobility is reduced, leading to the build-up of tensile stress resulting from attractive forces between under-dense neighbouring column boundary and possible void formation, while crystallites can still remain under compressive stress.

36 MATERIALS SCIENCE↗

Effect of Recrystallization on Gas Bubble Swelling in UMo Fuels

The development of low-enriched uranium (LEU) fuels such as UMo dispersion fuels and monolithic UMo fuels is part of a global effort on nuclear nonproliferation. Although UMo fuels have the advantage of high density, excellent irradiation performance and good thermal conductivity, the volumetric swelling in irradiated metallic fuels is known to be an important design parameter because it affects not only the thermal conductivity of the fuels but also the mechanical integrity of fuel structures. Experiments also show that recrystallization dramatically affects the gas bubble swelling kinetics. A series of materials processes such as casting, mechanical rolling and thermal treatment are used in fuel fabrication. Resulting microstructure, such as grain size, porosity, and second phase, strongly depends on the material processes and process parameters. Therefore, a fundamental understanding how fabricated microstructures and irradiation conditions affect the nucleation of gas bubbles, recrystallization and gas bubble swelling kinetics is essential for optimizing material processes to obtain desired microstructure and fuel performance. Great effort has been made in the development of modeling capability for predicting gas bubble swelling kinetics and fission gas release kinetics in nuclear fuels. However, these models are based on the assumptions that the inter- and intra-granular gas bubble sizes are independent of position and only depend on time or fission density. Therefore, they are applicable to a material with uniform microstructure such as equiaxed grains with homogeneous defect distributions, homogeneous thermodynamic and kinetic properties of defects, and uniform radiation conditions. Very recently, we developed a three dimension (3D) microstructure dependent gas bubble swelling model for investigating the effect of heterogeneous microstructures and inhomogeneous thermodynamic properties of defects on gas bubble swelling in polycrystalline UMo fuels. However, the model doesn't take into account the effect of recrystallization on swelling kinetics. In this work, the spatially dependent rate theory is used to describe the evolution of interstitials and interstitial loop density. Recrystallization is described by a phase-field model with a concept of 'phase transition' when the local interstitial loop density is larger than a critical value. The intra- and inter- granular gas bubble evolution is described by the spatially dependent Booth model. A model integrating all the microstructure evolution enables one to study the effect of heterogeneous microstructures, recrystallization, and the metallic fuel thermodynamic and kinetic properties on gas bubble swelling kinetics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal and temporal evolution of microstructure in polycrystalline ZnO

Tug between electronics and spintronics has opened up new area of research named as dilute magnetic semiconductors (DMS), ZnO is one of the most reliable candidates for spintronic devices and DMS. Since, pure and transition metal doped polycrystalline ZnO shows room temperature ferromagnetism, therefore it is very important to gain insight into its microstructure (MS) evolution. We report thermal evolution of MS of pure ZnO on sintering it at 200 °C, 400 °C, 600 °C, and 800 °C in ambient atmosphere for two hours. Temporal evolution at fixed temperature was analyzed using mean field model of internal energy and entropy. Grain size of ZnO MS were analyzed using integral breadth method of X-ray diffraction (XRD) lines using Voigt profile fit,. XRD line corresponding to [101] plane shifts from 36.17° to 36.28° whereas grain size increases from 67.5 nm to 93.7 nm with increase of temperature from 23°C to 800°C respectively. Grain growth with increase of temperature show Arrhenius type behavior with activation energy of 30.77 kJ-mol{sup −1} and temporal growth shows diffusive behavior with exponent 0.5.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗

Evolution of Dynamic Recrystallization in 35CrMo Steel During Hot Deformation

To better understand the dynamic recrystallization (DRX) behavior of 35CrMo steel during hot deformation, a series of isothermal compression tests were carried out at different temperatures and strain rates. Using a constitutive equation built from the data obtained and the Arrhenius equation, the activation energy for hot deformation was determined through regression to be 342.69 kJ/mol. A model of the DRX kinetics was also constructed to characterize the influence of accumulated strain, temperature and strain rate on DRX evolution, which revealed that lower temperatures and higher strain rates require greater strain to achieve the same DRX volume fraction. Optical examination of the microstructure after deformation confirmed that this model accurately reflects reality and that grain size varies directly with deformation temperature, but inversely with strain rate.

36 MATERIALS SCIENCE↗

Influence of cementation on the yield surface of rocks numerically determined from digital microstructures

Digital Rock Physics has reached a level of maturity on the characterisation of primary properties that depend on the microstructure – such as porosity, permeability or elastic moduli – by numerically solving field equations on μCT scan images of rock. After small deformations or at depth though, most rocks eventually reach their limit of elasticity and the complementary plastic properties are needed to describe the full mechanical behaviour. Currently, determination of a rock’s yield surface from its microstructure is often restricted to semi-analytical criteria derived by limit analysis or numerical simulations performed on idealised geometries. Such simplification lacks representativeness, particularly for processes that affect directly the pore-grain interface such as the cementation phenomenon, happening during diagenesis. Eventually, only direct numerical simulation of elasto-plasticity performed on digitalised microstructures can be used to assess the strength of different cemented materials and its evolution with the alteration of the microstructure. In this study, we provide a comprehensive parametric study on the impact of cementation on rock strength for real microstructures of cemented granular materials. Compared to most previous studies, the whole yield surface is determined numerically (using Finite Element Method) in order to assess the influence of cementation for different stress-paths. The previously known tendency of rock to strengthen with increasing cementation volume is verified. New results on the influence of cement property namely Young’s modulus, friction and cohesion on the rock’s yield surface are explored. The envelopes obtained are compared to the ones obtained by experimental data and existing models. Finally, the framework presented in this study showcases the wider possibility of determining any rock’s or porous material’s yield surface from its microstructure.

36 MATERIALS SCIENCE↗

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗

Effect of Zn on microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloys with a medium number of Fe-rich phase particles

Highlights: • Zn has a negligible influence on the final recrystallization microstructure and texture of Al-Mg-Si-Cu alloys. • By adding Fe-rich phase particles to refine the recrystallization grain sizes could control the texture. • The deep drawability of Al-Mg-Si-Cu alloys could be affected by solute Zn atom besides the microstructure and texture. - Abstract: The effect of Zn on the microstructure, texture evolution and mechanical properties of Al-Mg-Si-Cu alloys with a medium number of Fe-rich phase particles was investigated using tensile testing machine, optical microscopy (OM), scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffractometer (XRD) in the present study. The results show that Zn addition has a significant influence on the final mechanical properties, but a slight effect on microstructure and final recrystallization texture. Zn addition is favorable to increase yield strength, ultimate tensile strength and elongation, however it is detrimental to improve r value and reduce Δr value. During the thermomechanical processing, the microstructure almost has nothing to do with Zn addition. However, Zn could prevent the secondary phase particles from precipitating during intermediate annealing. In contrast to the alloy sheet without Zn, the alloy sheet with 1.0 wt% Zn always has weaker textures before final cold rolling, but a stronger texture after experiencing final cold rolling. After solution treatment, they almost possess the same recrystallization texture. Finally, the effect of Zn addition on the recrystallization texture was discussed. Their similar recrystallization texture can be attributed to the similar microstructure, which was caused by the medium number of Fe-rich phase particles.

36 MATERIALS SCIENCE↗

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

36 MATERIALS SCIENCE↗

Kinetic Monte Carlo simulations of structural evolution during anneal of additively manufactured materials

Our experiments indicated that upon a post-processing anneal, an additively manufactured 316L stainless steel exhibits cubic grains rather than the conventional equiaxed grains. In this work, we have used kinetic Monte Carlo simulations to explore the origin of these cubic grains. First, we implemented a new kinetic Monte Carlo model in parallel code SPPARKS to simulate grain growth and recrystallization under a residual energy distribution. Our model incorporates physical properties and real-time, as opposed to generic properties and relative time. We further validated that our SPPARKS simulations reproduced the expected kinetic behavior of single-grain evolution. We then used the validated approach to simulate the anneal of an additively manufactured material under the same conditions used in our experiments. We found that the cubic grains can origin from a periodically varying residual energy that may be present in additively manufactured materials.

36 MATERIALS SCIENCE↗