Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYPERSONIC BOUNDARY LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Fitting aerodynamics and propulsion into the puzzle

The development of an airbreathing single-stage-to-orbit vehicle, in particular the problems of aerodynamics and propulsion integration, is examined. The boundary layer transition on constant pressure surfaces at hypersonic velocities, and the effects of noise on the transition are investigated. The importance of viscosity, real-gas effects, and drag at hypersonic speeds is discussed. A propulsion system with sufficient propulsive lift to enhance the performance of the vehicle is being developed. The difficulties of engine-airframe integration are analyzed.

Johnston, Patrick J.↗
NASA NTRS2004

DSMC Simulations of Hypersonic Flows With Shock Interactions and Validation With Experiments

The capabilities of a relatively new direct simulation Monte Carlo (DSMC) code are examined for the problem of hypersonic laminar shock/shock and shock/boundary layer interactions, where boundary layer separation is an important feature of the flow. Flow about two model configurations is considered, where both configurations (a biconic and a hollow cylinder-flare) have recent published experimental measurements. The computations are made by using the DS2V code of Bird, a general two-dimensional/axisymmetric time accurate code that incorporates many of the advances in DSMC over the past decade. The current focus is on flows produced in ground-based facilities at Mach 12 and 16 test conditions with nitrogen as the test gas and the test models at zero incidence. Results presented highlight the sensitivity of the calculations to grid resolution, sensitivity to physical modeling parameters, and comparison with experimental measurements. Information is provided concerning the flow structure and surface results for the extent of separation, heating, pressure, and skin friction.

Moss, James N.↗
NASA NTRS2004

DSMC Simulations of Hypersonic Flows With Shock Interactions and Validation With Experiments

The capabilities of a relatively new direct simulation Monte Carlo (DSMC) code are examined for the problem of hypersonic laminar shock/shock and shock/boundary layer interactions, where boundary layer separation is an important feature of the flow. Flow about two model configurations is considered, where both configurations (a biconic and a hollow cylinder-flare) have recent published experimental measurements. The computations are made by using the DS2V code of Bird, a general two-dimensional/axisymmetric time accurate code that incorporates many of the advances in DSMC over the past decade. The current focus is on flows produced in ground-based facilities at Mach 12 and 16 test conditions with nitrogen as the test gas and the test models at zero incidence. Results presented highlight the sensitivity of the calculations to grid resolutions, sensitivity to physical modeling parameters, and comparison with experimental measurements. Information is provided concerning the flow structure and surface results for the extent of separation, heating, pressure, and skin friction.

Moss, James N.↗
NASA NTRS2012

Hypersonic Transition Analysis for HIFiRE Experiments

The HIFiRE-1 flight experiment provided a valuable database pertaining to boundary layer transition over a 7-degree half-angle, circular cone model from supersonic to hypersonic Mach numbers, and a range of Reynolds numbers and angles of attack. This paper reports selected findings from the ongoing computational analysis of the measured in-flight transition behavior. Transition during the ascent phase at nearly zero degree angle of attack is dominated by second mode instabilities except in the vicinity of the cone meridian where a roughness element was placed midway along the length of the cone. The growth of first mode instabilities is found to be weak at all trajectory points analyzed from the ascent phase. For times less than approximately 18.5 seconds into the flight, the peak amplification ratio for second mode disturbances is sufficiently small because of the lower Mach numbers at earlier times, so that the transition behavior inferred from the measurements is attributed to an unknown physical mechanism, potentially related to step discontinuities in surface height near the locations of a change in the surface material. Based on the time histories of temperature and/or heat flux at transducer locations within the aft portion of the cone, the onset of transition correlated with a linear N-factor, based on parabolized stability equations, of approximately 13. Due to the large angles of attack during the re-entry phase, crossflow instability may play a significant role in transition. Computations also indicate the presence of pronounced crossflow separation over a significant portion of the trajectory segment that is relevant to transition analysis.

Li, Fei↗
NASA NTRS1997

Invariance of Hypersonic Normal Force Coefficients with Reynolds Number and Determination of Inviscid Wave Drag from Laminar Experimental Results

Observations have been made and reported that the experimental normal force coefficients at a constant angle of attack were constant with a variation of more than 2 orders of magnitude of Reynolds number at a free-stream Mach number M(sub infinity) of 8.00 and more than 1 order of magnitude variation at M(sub infinity) = 6.00 on the same body-wing hypersonic cruise configuration. These data were recorded under laminar, transitional, and turbulent boundary layer conditions with both hot-wall and cold-wall models. This report presents experimental data on 25 configurations of 17 models of both simple and complex geometry taken at M(sub infinity) = 6.00, 6.86, and 8.00 in 4 different hypersonic facilities. Aerodynamic calculations were made by computational fluid dynamics (CID) and engineering methods to analyze these data. The conclusions were that the normal force coefficients at a given altitude are constant with Reynolds numbers at hypersonic speeds and that the axial force coefficients recorded under laminar boundary-layer conditions at several Reynolds numbers may be plotted against the laminar parameter (the reciprocal of the Reynolds number to the one-half power) and extrapolated to the ordinate axis to determine the inviscid-wave-drag coefficient at the intercept.

Hawkins, Richard↗
NASA NTRS1988

Passive control plate for shock-boundary layer interactions

Computational and experimental results are presented for a passive method capable of reducing or completely eliminating the separation region in shock-boundary layer interactions of the type that can result in severe performance degradation due to flow separation in supersonic and hypersonic inlets. The method involves the placement of an embedded plate in the outer portion of the boundary layer, parallel to the wall, so that the incident shock will impinge upon, and be reflected from, its surface. This will lower the pressure gradient in the low-momentum, near-wall region. A porous control plate's effect has also been investigated.

Goodman, Wesley L.↗
NASA NTRS1978

Inlet boundary-layer shapes on four aircraft forebodies at Mach 6

Boundary-layer shape measurements at the engine inlet on four different hypersonic aircraft forebody designs (with no engine on the forebody) are reported. The measurements provide a qualitative assessment of the effectiveness of various forebody geometries as engine inlet precompression surfaces. The designs, tested in a hypersonic tunnel at Mach 6 and a nominal freestream Reynolds number of 30,500,000, included a semiconical forebody, a configuration similar to a slab delta wing, a conical nose blended into a flat surface, and a conical, complex forebody shape. Boundary layer height as a function of forebody compression is shown for each design.

Lawing, P. L.↗
NASA NTRS1993

Perspectives on hypersonic viscous flow research

Issues and advances in current hypersonic flow research perceived to be of interest in theoretical fluid/gas dynamics are reviewed. Particular attention is given to the hypersonic aircraft as waverider, computational methods and theoretical development in the study of viscous interaction, and boundary-layer instability and transition studies. In the present framework the study of viscous hypersonic flow faces transition problems of two kinds which represent the two major areas of current research: the turbulence transition in the high Re range and the transition to the free-molecule limit.

Cheng, H. K.↗
NASA NTRS2007

Simulations of Boundary-Layer Transition

For incompressible benchmark flows, we have demonstrated the capability of the parabolized stability equations (PSE) to simulate the transition process in excellent agreement with microscopic experiments and direct Navier-Stokes simulations at modest computational cost. Encouraged by these results, we have developed the PSE methodology of three-dimensional boundary-layers in general curvilinear coordinates for the range from low to hypersonic speeds, and for both linear and nonlinear problems. For given initial and boundary conditions, the approach permits simulations from receptivity through linear and secondary instabilities into the late stages of transition where significant changes in skin friction and heat transfer coefficients occur. We have performed transition simulations for a variety of two- and three-dimensional similarity solutions and for realistic flows over swept wings at subsonic and supersonic speeds, the pressure ans suction side of turbine blades at low and medium turbulence levels, and over a blunt cone at Mach number Ma = 8. We present selected results for different transition mechanisms with emphasis on the late stage of transition and the evolution of wall-shear stress and heat transfer.

Herbert, Thorwald↗
NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗
NASA NTRS2010

Transition Experiments on Blunt Bodies with Isolated Roughness Elements in Hypersonic Free Flight

Smooth titanium hemispheres with isolated three-dimensional (3D) surface roughness elements were flown in the NASA Ames hypersonic ballistic range through quiescent CO2 and air environments. Global surface intensity (temperature) distributions were optically measured and thermal wakes behind individual roughness elements were analyzed to define tripping effectiveness. Real-gas Navier-Stokes calculations of model flowfields, including laminar boundary layer development in these flowfields, were conducted predict key dimensionless parameters used to correlate transition on blunt bodies in hypersonic flow. For isolated roughness elements totally immersed within the laminar boundary layer, critical roughness Reynolds numbers for flights in air were found to be higher than those measured for flights in CO2, i.e., it was easier to trip the CO2 boundary layer to turbulence. Tripping effectiveness was found to be dependent on trip location within the subsonic region of the blunt body flowfield, with effective tripping being most difficult to achieve for elements positioned closest to the stagnation point. Direct comparisons of critical roughness Reynolds numbers for 3D isolated versus 3D distributed roughness elements for flights in air showed that distributed roughness patterns were significantly more effective at tripping the blunt body laminar boundary layer to turbulence.

Reda, Daniel C.↗
NASA NTRS1974

Development of a high Reynolds number quiet tunnel for transition research

High noise levels in conventional supersonic and hypersonic wind tunnels prevent further advances in transition research. Recent data confirm previous results that transition is dominated by tunnel noise when the rms pressure intensities exceed about 1%. High facility noise levels also dominate fluctuating pressure loads under fully turbulent boundary layers. Recent data on the power spectra of surface pressures indicate that the basic structure of turbulent boundary layers may be modified by high facility noise levels. Experimental data for current techniques to control and reduce noise levels in supersonic and hypersonic wind tunnels by laminarization of nozzle wall boundary layers and by noise radiation shields are presented. These results and possible effects of Taylor-Gortler vortices observed in a nozzle wall boundary layer are used to predict the limits of quiet performance for a proposed 20-in. quiet tunnel.

Beckwith, I. E.↗
NASA NTRS1984

Aerodynamic heating rate distributions induced by trailing edge controls on hypersonic aircraft configurations at Mach 8

Aerodynamic surface heating rate distributions in three dimensional shock wave boundary layer interaction flow regions are presented for a generic set of model configurations representative of the aft portion of hypersonic aircraft. Heat transfer data were obtained using the phase change coating technique (paint) and, at particular spanwise and streamwise stations for sample cases, by the thin wall transient temperature technique (thermocouples). Surface oil flow patterns are also shown. The good accuracy of the detailed heat transfer data, as attested in part by their repeatability, is attributable partially to the comparatively high temperature potential of the NASA-Langley Mach 8 Variable Density Tunnel. The data are well suited to help guide heating analyses of Mach 8 aircraft, and should be considered in formulating improvements to empiric analytic methods for calculating heat transfer rate coefficient distributions.

Kaufman, L. G., II↗
NASA NTRS2001

Development of an Unstructured Mesh Code for Flows About Complete Vehicles

This report describes the research work undertaken at the Massachusetts Institute of Technology, under NASA Research Grant NAG4-157. The aim of this research is to identify effective algorithms and methodologies for the efficient and routine solution of flow simulations about complete vehicle configurations. For over ten years we have received support from NASA to develop unstructured mesh methods for Computational Fluid Dynamics. As a result of this effort a methodology based on the use of unstructured adapted meshes of tetrahedra and finite volume flow solvers has been developed. A number of gridding algorithms, flow solvers, and adaptive strategies have been proposed. The most successful algorithms developed from the basis of the unstructured mesh system FELISA. The FELISA system has been extensively for the analysis of transonic and hypersonic flows about complete vehicle configurations. The system is highly automatic and allows for the routine aerodynamic analysis of complex configurations starting from CAD data. The code has been parallelized and utilizes efficient solution algorithms. For hypersonic flows, a version of the code which incorporates real gas effects, has been produced. The FELISA system is also a component of the STARS aeroservoelastic system developed at NASA Dryden. One of the latest developments before the start of this grant was to extend the system to include viscous effects. This required the development of viscous generators, capable of generating the anisotropic grids required to represent boundary layers, and viscous flow solvers. We show some sample hypersonic viscous computations using the developed viscous generators and solvers. Although this initial results were encouraging it became apparent that in order to develop a fully functional capability for viscous flows, several advances in solution accuracy, robustness and efficiency were required. In this grant we set out to investigate some novel methodologies that could lead to the required improvements. In particular we focused on two fronts: (1) finite element methods and (2) iterative algebraic multigrid solution techniques.

Peraire, Jaime↗
DOE OSTI2024

On the accuracy of compressibility transformations

This study highlights the importance of satisfying the eddy viscosity equivalence below the logarithmic layer, to deriving accurate compressibility transformations. First, we analyze the ability of known transformations to satisfy the eddy viscosity equivalence and show that the accuracy of these transformations is strongly dependent on this ability. Second, in a step-by-step manner, we devise new transformations that satisfy this hypothesis. An approach based on curve fitting of the incompressible Direct Numerical Simulation data for eddy viscosity profiles below the logarithmic layer provides an extremely accurate transformation, which motivates self-contained methods, making use of mixing length formulas in the inner region. It is shown that the accuracy of existing transformations can be significantly improved by applying these ideas, below the logarithmic layer. Motivated by the effectiveness of the formulations derived from eddy viscosity equivalence, we introduce a new integral transformation based on Reynolds number equivalence between compressible and incompressible flows. This approach is based on defining a new compressible velocity scale, which affects the accuracy of transformations. Several choices for the velocity scale are tested, and in each attempt, it is shown that the eddy viscosity equivalence plays a very important role for the accuracy of compressibility transformations.

42 ENGINEERING↗