Search NASA⌕ Search

SEARCH · Search NASA

Results for “Heating experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Thermal hydraulic analysis of the AFIP-7 irradiation test in the Advanced test Reactor – Model correlation and performance evaluation

We report as a system level code, RELAP5 is widely used in the nuclear field for the reactor hydraulic analysis. In the component/experimental level, it is frequently employed as well. This paper demonstrates that the RELAP5 flow simulation of the AFIP-7 irradiation experiment which has a complicated 3D geometry/flow path deviates by ~28% from the flow evaluation through a computational fluid dynamics (CFD) simulation, which has been validated against a flow test performed at Oregon State University. Thermal safety compliance analysis of an experiment planned to be irradiated in the Advanced Test Reactor is usually performed using the finite element analysis code, Abaqus. This research reveals the disadvantages of the Abaqus simulation in the flow instability and departure from nucleate boiling evaluations via a conjugate heat transfer analysis of the AFIP-7 irradiation experiment. As a result, a detailed CFD simulation is suggested for irradiation experiments with complicated flow paths, rather than a simplified RELAP5 simulation or hand calculations. The validated simulation approach will be integrated with the Boehmite correlations to investigate the oxide growth prediction on the fuel cladding in Part II of this research.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

High-Pressure Melting Experiments of Fe 3 C and a Thermodynamic Model of Fe-C Liquids for the Earth's Core

Melting experiments of Fe 3 C were conducted to 85 GPa in laser-heated diamond anvil cells with in situ X-ray diffraction and post-experiment textural observation. From the determined pressure-temperature conditions of the melting curve for Fe 3 C, together with literature data on the melting point of diamond and eutectic point of the system Fe-Fe 3 C/Fe 7 C 3 under high pressures, we established a self-consistent thermodynamic model for high-pressure melting of the system Fe-C including the mixing parameters for liquids. The results show that mixing of Fe and C liquids is negatively nonideal from 1 bar to the pressure at the center of the Earth. The departure from ideal mixing becomes progressively larger with increasing pressure, which leads to greatly stabilized liquids under core pressures. The modeled carbon content in eutectic melts under core pressures is 3.3–4.4 wt%. From the Gibbs free energy, we derived an internally consistent parameters for Fe-C outer cores which included the crystallizing points at their bottoms, isentropic thermal profiles, and densities and longitudinal seismic wave speeds (Vp). While the addition of carbon in excess of the eutectic melt composition effectively reduces the density of iron liquid, the Vp of iron liquid is not greatly changed. Therefore, the low density and high Vp of PREM relative to pure iron cannot be reconciled by an Fe-C liquid. Therefore, the Earth's core cannot be approximated by the system Fe-C and should include another light element.

58 GEOSCIENCES↗
DOE OSTI2022

Passive heat removal in horizontally oriented micro-HTGRs

There are novel, horizontally oriented high-temperature gas-cooled micro-reactor (HTGR) designs under consideration because of their portability, simplicity, and reliable operation. These features of the micro-HTGR design can meet the fission battery attributes, such as economic, standardize, installed, unattended and reliable. Although there have been HTGR related safety studies, micro-HTGRs when horizontally oriented are expected to exhibit significantly different thermal physics. During the unavailability of helium circulation, the internal reactor core is designed to cool by block-to-block conduction and radiation, and the reactor vessel surface is cooled by the ambient air. This scenario is anticipated during the transport of the micro-HTGR in a shipping container. The conduction and radiation between the prismatic micro-HTGR blocks in the core can be influenced by variances in the thermal contacts. This work investigated the conduction within a simulated horizontal HTGR core. An experimental setup was used to validate a numerical model. The experimental setup consisted of a hexagonal assembly with scaled prismatic blocks placed within a high-temperature vacuum environment. The gaps between the blocks were well controlled and monitored. The experimental setup was designed in such a way that the temperature variation in the axial direction was minimal, such that the experiment could be observed as a 2D (r, ) heat transfer problem. The pressurized tube was equipped with Infra-Red (IR) transparent windows, and an IR camera was used to capture the spatio-temporal temperature evolution in the hexagonal block assembly during the cooldown experiments. The experimental scenario was computationally modeled with a finite element analysis (FEA) program. Once validated, the computational model was used to investigate the impact of gap conductance on overall decay heat removal. Using a conservative estimate for gap conductance value (100 W/m 2 -K) between the prismatic blocks, there is a negligible increase in temperature observed during decay heat generation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Convectively Induced Secondary Circulations and Wind‐Driven Heat Fluxes in the Surface Energy Balance Over Land

Increased resolution has enabled kilometer-scale weather and climate models to partially resolve secondary circulations, including horizontal convective rolls (HCRs) and cold pool gust fronts. Although these circulations are ubiquitous in convective boundary layers over land, their impacts on the surface energy balance are largely unknown. Doppler lidar and surface observations were combined with DOE E3SM land model experiments, revealing increased surface winds (5 m/s) and heat fluxes (50 W/m 2 ) in convergent branches of HCRs. Larger wind-driven flux responses (up to 150 W/m 2 ) were found along gust fronts. Surface energy balance shifts to accommodate wind-driven fluxes, reducing ground heat conduction and longwave cooling. Our findings from the US Southern Great Plains are broadly relevant to modeling convective boundary layers. In particular, widely used subgrid wind gust parameterizations were found to be physically inconsistent with resolved secondary circulations and could worsen climate prediction biases at kilometer-scales.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Involute Working Group – Validation of CFD Turbulence Models for Steady-State Safety Analysis

There are three research reactors in the world having fuel plates curved as circle-involute (a spiral generated around a circle): The Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) located in Tennessee, U.S.A. [ORNL, 2018]; The Laue-Langevin Institute (ILL) High Flux Reactor (RHF) located in Grenoble, France [ILL, 2018]; and, The Technical University of Munich (TUM) Research Neutron Source Heinz Maier-Leibnitz (FRM II) located in Garching, Germany [TUM, 2018]. All three reactors are currently using Highly Enriched Uranium (HEU, 235U/U ≥ 20 wt. %) as fuel and all three are actively engaged in activities to convert to Low Enriched Uranium (LEU, 235U/U < 20 wt. %) fuel. More information on these reactors can be found in Section two. For various reasons, these reactors have expressed interest in using Computational Fluid Dynamics (CFD) tools to perform their Steady-State Thermal-Hydraulic (SSTH) safety calculations. Using CFD tools for SSTH analysis represents generally a significant departure from traditional methods and requires thorough verification and validation (V&V) to be accepted by regulators. This is why Argonne National Laboratory (ANL) and the involute reactors formed an informal group to help each other in this endeavor. This so-called Involute Working Group (IWG) aims at supporting the qualification of CFD tools for SSTH safety calculations. Activities include benchmarking, code-to-code comparison, Verification and Validation (V&V) as well as technical support. More information on the IWG and the reasons why involute-plate reactors are interested in CFD can be found in Section three. The present study aims at testing three turbulence models commonly implemented in commercial software (namely K-Epsilon, K-Omega and Reynolds-Stress) and assessing their relevance for involute-plate reactor application. An experiment performed by Gambill and Bundy in 1961 was performed to measure heat transfer coefficients in conditions prototypic of the HFIR reactor [Gambill, 1961]. More details on this experiment are provided in Section four. Based on the information available, CFD models of this experiment have been created and the experimental results have been compared to the ones obtained with these CFD models. CFD models and the results of this comparison are provided in Section five.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

PARFUME/BISON Fission Product Release Predictions versus AGR-3/4 Heating Test Measurements

The fuel performance modeling codes PARFUME (PARticle FUel ModEl) and BISON were used to predict the release of fission products silver, cesium, and strontium from as-irradiated fuel compacts containing tristructural isotropic (TRISO) coated particles during heating tests post irradiation. The AGR-3/4 fuel compacts were irradiated as part of the third and fourth series of planned experiments to support the Advanced Gas Reactor (AGR) program. The heating tests were conducted at temperatures between 1200°C and 1700°C to simulate reactor accident conditions. The measured fission product release fractions from the heating tests were compared to modeling predictions calculated by PARFUME and BISON to evaluate how the codes compare to experimental results. Comparisons between the experimental measured fission product release fractions from silver, cesium and strontium indicate that both modeling codes overpredict the fission product release fractions demonstrating that the diffusivities used in the codes are overestimated. This results in a conservative estimate predicted by the codes when evaluating the fission product release relative to experimental data as it pertains to silver, cesium, and strontium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Key advancements toward eliminating the “drive deficit” in ICF hohlraum simulations

This paper, extended from a Letter [Chen et al., Phys. Rev. E 110, L013201 (2024)] published in Phys. Rev. E in 2024, presents detailed results from a set of experiments studying the x-ray drive produced in laser-heated ignition-scale hohlraums at the National Ignition Facility. The results reveal that deficiencies in non-local thermodynamic equilibrium atomics physics calculations of gold emissivity lead to the overestimation of the “M-band” radiation and are responsible for discrepancies in drive predictions vs measurements in these hohlraums. These experiments were performed on ViewFactor targets with the same gas fill and laser pulse shapes as currently used in ongoing ignition experiments. The common hohlraum model with a magnetohydrodynamics heat transport model and a 10%–20% reduction to the M-band absorption and emission opacity can bring the simulations into agreement with several independent measurements, including the absolute radiation flux, the radiation flux in the 2–4 keV spectral range, and spectroscopic measurements of both K-shell dopant and L-shell gold. This new model is applicable to ICF and high-energy density experiments that use gold hohlraums as drivers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Thermal-striping analysis methodology for sodium-cooled reactor design

Computational fluid dynamics simulations have been performed to study the applicability of engineering CFD methods for thermals striping analysis. Thermal striping is the fluctuating temperature profile in a solid caused by fluctuating fluid temperature, and the resulting fluctuating thermal stresses cause high cycle fatigue and eventual material failure. Here this study presents the methodology for thermal striping analysis that including a transient conjugate heat transfer RANS model and benchmark the results against a sodium triple jet experiment. The multiphysics calculations are implemented to analyze the thermal stresses in the solid domain caused by the coupled heat transfer between the fluid and solid domains. Validation data from a liquid sodium triple jet experiment include time-averaged temperature measurements and power spectra of the temperature signal. The numerical results agree well with these experimental measures, demonstrating key features such as the dominant frequency of temperature fluctuations. The applicability of a low-cost wall treatment method is demonstrated, enabling key computational savings. Finally, the performance of two finite element stress analysis software packages is compared, and the validity of the lower-cost method is confirmed. These results demonstrate the applicability of engineering methods for computational thermal striping calculations, enabling thermal striping estimations in large fluid systems such as the core of a Sodium-cooled nuclear reactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Progress on Producing an ODS Ferritic Alloy by High Deformation Processing of Reactive Powders

Oxide dispersion-strengthened (ODS) ferritic alloys, such as 14YWT, are considered as benchmarks for fuel cladding and core structural materials in advanced nuclear energy reactor systems that require high temperature strength and creep properties as well as resistance to radiation damage. Unfortunately, the popular processing method of mechanical alloying (MA) is time-consuming, incurs high manufacturing costs, and typically produces anisotropy in the microstructure and mechanical properties of ODS ferritic alloys. These considerations hinder their acceptance in many high-performance, high-temperature materials for advanced nuclear energy reactors. This work package is pursuing an alternative solid-state processing to MA involving high deformation at high temperatures for producing an ODS ferritic alloy for fuel cladding. This report summarizes the concept for this processing method and the progress toward selecting the reactive and ferritic alloy powders, preparing 316L stainless steel cans for filling with blended powder followed by degassing, and choosing the heat treatments and forging parameters for performing the first two forging experiments. The preliminary results of optical microscopy performed on polished samples that were cut in three orthogonal directions revealed remnant porosity in both samples. The analysis of the porosity using ImageJ revealed a lesser amount of ~2.49% in the HiLoMe-1 sample that was processed with the three heat treatments and forging parameters compared to ~5.70% for the Hi-1 sample that was processed with only the first sintering heat treatment and forging parameter. These initial results will provide insights that can be leveraged to improve the densification of the powders in future forging experiments that will be continued into FY24 for determining the optimum heat treatments and forging parameters coupled with detailed microstructure characterization studies for producing the ODS ferritic alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Thermocouple Testing in Support of the AGR-5/6/7 Experiment

This report documents thermocouple testing performed in IRC Lab C-15 over a period of seven years. This testing supported selection and characterization of the thermocouple set used in the AGR-5/6/7 experiment. The following summary was taken directly from the report. Temperature measurement is a challenging aspect of very high temperature irradiation experiments because commonly used high-temperature commercial thermocouples such as platinum-rhodium (Types S, R, and B) and tungsten-rhenium (Type C), suffer dramatic drift because of neutron-induced transmutation. As a result, these types of thermocouples, which are used routinely for industrial temperature measurements outside of reactors, are used only in very special circumstances for reactor experiments. Conversely, because of their low neutron cross-sections, Type N thermocouples are affected to only a limited extent by neutron irradiation. However, the use of these nickel-based thermocouples is limited when the temperature exceeds 1050°C due to drift arising from minor alloying elements migrating from the thermocouple's metal sheath to the thermoelements. This change in the composition of the thermo-elements results in significant decalibration of the signal. The issues described above were recognized during the early planning stages of the final AGR experiment (designated AGR-5/6/7), and a thermocouple furnace testing program was performed over a seven-year period (2014-2019, 2021) to first select and then characterize the best thermocouple set for the high temperature regions of the AGR-5/6/7 irradiation experiment. The calculated temperature range of the AGR-5/6/7 experiment was 600–1500°C. For temperatures below 1000°C standard Type N thermocouples were deemed adequate. The furnace testing campaign identified two thermocouple types suitable for measuring temperatures above 1000°C, a Mo/Nb thermocouple developed at INL called HTIR-TC, and a Type N thermocouple developed by Cambridge University (called herein Cambridge Type N), which featured a custom high nickel alloy sheath. One of the original goals of the furnace testing program was to identify a thermocouple capable of low drift operation near the peak temperature expected in AGR-5/6/7, i.e., about 1400°C. The HTIR-TC design appeared promising in this regard, however a manufacturing difficulty proved to be a barrier and instead the furnace testing focused on drift performance at 1250°C. The manufacturing difficulty was that the Nb sheaths of the HTIR-TCs experienced extreme embrittlement when heat treated at 1600°C or greater. Heat treatment is needed to stabilize the emf output of this TC type, and the higher the heat treatment temperature the higher the peak temperature of stable operation. Because of the sheath embrittlement the heat treatment temperature had to be lowered to 1450°C resulting in a stable operating temperature of about 1250°C. One of the successes of the furnace testing program was identification of a shortcoming in the heat treatment procedure that had been traditionally used in the production of HTIR-TCs. The shortcoming was that the entire heated length of the HTIR-TC sensor was not being heat treated, but rather only the part of the sensor expected to experience temperatures above 1000°C. The problem manifested itself when the thermocouples were removed from the heat treat furnace and placed in another furnace with a different geometry, their indicated temperatures would be widely scattered, but mostly in the negative direction. The solution was to heat treat the entire heated length of the sensor. Since the deepest immersion depth in the AGR-5/6/7 experiment was about 40 inches, a heat treatment length of 48 inches was used. After this change was implemented, thermocouples which were moved into a new environment with a different temperature profile (i.e., a different furnace), produced accurate temperature measurements. Although assembly of the AGR-5/6/7 experiment was completed in September of 2017 (and irradiation begun in 2018), furnace testing of thermocouples continued in 2018 and 2019. The main purpose of this testing was to establish very long-term drift characteristics of the HTIR and Cambridge Type N thermocouples installed in the experiment. Representative thermocouples from the same lots as those installed in the AGR-5/6/7 experiment were used. Additionally, thermocouples of different designs, (particularly variations on the HTIR-TC design) were "piggy-backed" on this testing program to provide insights for instrumenting future very high temperature irradiation experiments. This two-year testing program demonstrated that HTIR-TCs and Cambridge Type N TCs could operate at 1250°C for up to 10,000 hrs (and in some cases longer) while experiencing negative drifts on the order of 2-4°C/1000 hrs. This performance was considered acceptable given the extreme operating environment the sensors faced.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Thermal Analysis of the Sirius-3 Nuclear Propulsion Fuel Experiments

To support long space missions, NASA is designing and testing different fuels for nuclear thermal propulsion. These designs include a number ceramic metallic fuels which are to be irradiated in the Tranisent Test Reactor to test the fuel’s performance at protypical conditions. The irradiation campaign of these fuels is referred to as the Sirius experiments, and includes single and stacked experiment samples. In this paper we present the thermal analysis of the Sirius-3 experiment. For this analysis, temperatures from a Bison finite element model are compared to the temperatures obtained from an experiment thermocouple where good agreement between the two are found. Because agreement of the thermocouple and Bison finite element model, insight into the heat flow is provided to experimenters as they design future experiments. As an example of this insight, the rods through the fuel specimen as shown in Sirius A and B [1] were removed and replaced with hold down rings for the Sirius-2C

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Thermal Experiments for Fractured Rock Characterization: Theoretical Analysis and Inverse Modeling

Abstract Field‐scale properties of fractured rocks play a crucial role in many subsurface applications, yet methodologies for identification of the statistical parameters of a discrete fracture network (DFN) are scarce. We present an inversion technique to infer two such parameters, fracture density and fractal dimension, from cross‐borehole thermal experiments data. It is based on a particle‐based heat‐transfer model, whose evaluation is accelerated with a deep neural network (DNN) surrogate that is integrated into a grid search. The DNN is trained on a small number of the heat‐transfer model runs and predicts the cumulative density function of the thermal field. The latter is used to compute fine posterior distributions of the (to be estimated) parameters. Our synthetic experiments reveal that fracture density is well constrained by data, while fractal dimension is harder to determine. Adding nonuniform prior information related to the DFN connectivity improves the inference of this parameter.

Zhou, Zitong↗
DOE OSTI2023

Experimental and Numerical Investigation of Flow Boiling in Additive Manufactured Foam Structures With Vapor Pathways

Abstract The unique properties of metal foams make them potential candidates for a range of applications, including microsystem thermal management. Using additive manufacturing to create foam-type structures can improve upon prior thermal solutions by eliminating thermal interface materials and allowing for customization/local control of parameters. In the present investigation, flow boiling in additive-manufactured metal foams is investigated both experimentally and numerically. Two test samples, one with uniform structure and the other with pathways for vapor removal, are compared both experimentally and numerically. A conjugate computational fluid dynamics and heat transfer (CFD-HT) model utilizing a three-dimensional volume of fluid (VOF) model with accompanying evaporation/condensation model provided in-depth visualization of the boiling flow phenomena. The experiments generated the thermohydraulic performance over a range of heat fluxes, demonstrating that the sample incorporating dedicated vapor pathways performed better in both pressure and heat transfer performance metrics compared to the uniform foam. Additionally, negative system-level effects (i.e., hydraulic oscillations) were shown to be abated using the vapor removal structures. The numerical model yielded further insight into the factors contributing to the improved performance. Results indicated the pathways functioned as vapor removal channels, allowing the generated vapor to vent from the foam structure into the lanes. Further computational investigations demonstrated changes in flow regimes, where the addition of vapor channels caused the flow to change from churn to annular. Bubble behavior unique to the vapor pathway structure was studied, showing stagnant regions that eject vapor into the channel.

Engineering↗
DOE OSTI2020

Thermodynamics of monoclinic and tetragonal hafnium dioxide (HfO 2 ) at ambient pressure

Accurate and precise thermodynamic models of oxide compounds and their phases are important for calculating the phase stability of oxide materials. We develop and use a coupled quantum mechanical and molecular dynamics approach to create thermodynamic models of hafnia (HfO2) polymorphs from 0 K to 3000 K at ambient pressure. The approach is based on the quasi-harmonic approximation below the Debye temperature and on ab-initio molecular dynamics calculations above the Debye temperature to predict constant pressure heat capacities (C-p). A Bayesian model provides interpolated values between these regimes. As a case study, we develop thermodynamic models of monoclinic and tetragonal HfO2 polymorphs. The predicted heat capacities are in excellent agreement with experiment, and the predicted temperature of the monoclinic to tetragonal phase transition (2173 K) is in good agreement with the experimental value (2078K). These results provide a comprehensive and accurate thermodynamic model of the monoclinic and tetragonal phases of hafnia on a broad range of temperatures and can serve as input to CALPHAD assessment of multi-component hafnia-based phase diagrams.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Scale-up of microwave-assisted, continuous flow, liquid phase reactors: Application to 5-Hydroxymethylfurfural production

Microwave (MW) technology can be powerful for the electrification and intensification of chemical manufacturing. However, very few examples of scaled MW processes exist. In this work, we build a scaled, MW-assisted, continuous flow reactor for the processing of liquid phase chemistries with specific application to 5-hydroxymethylfurfural (HMF) production. Here, we demonstrate a corresponding computational fluid dynamics model to simulate the reactor’s temperature profile and performance, both of which are in good agreement with experiments. We construct a surrogate model to relate operating parameters to performance for guiding experiments, without demanding simulations, via active learning. Heat recirculation is demonstrated in this scaled reactor, further extending its scale and reducing the energy demand. An HMF yield of ~55 % and a productivity of 0.1 kg/hr, 8x higher than any other reactor, at a flowrate >20x than prior work, are demonstrated while maintaining energy efficiency of >98 %. A basic economic analysis estimates a $1.85/kg cost of HMF from fructose and >60 % reduction in CO 2 emissions than a conventional system without considering the impact of green electricity. We demonstrate that MW technology is well-applied to systems larger than the laboratory scale, and strategies to further reduction in cost and CO 2 are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Magnetism and finite-temperature effects in UZr 2 : A density functional theory analysis

The structure and the thermophysical properties of d-UZr 2 are investigated using 0 K density functional theory and ab initio molecular dynamics (AIMD). Modeling the true paramagnetic state of this intermetallic compound has been challenging using first-principles calculations. For the first time, we find that the generalized gradient approximation method without applying an on-site Coulomb interaction term (Hubbard U) can result in a ground state that is antiferromagnetic (AFM). We believe that this weak AFM ground state is the closest to the real paramagnetic state. We found that structure optimization at finite temperatures using AIMD is necessary to achieve this ground state instead of the non-magnetic and ferromagnetic states previously reported in the literature. Our findings indicate that applying the Hubbard U on uranium f-orbitals in this metallic system is unnecessary and not recommended, as it leads to a large overestimation of the volume and introduces an unphysical strong spin polarization. Finally, our approach results in atomic volume, thermal expansion, and heat capacities that have strong agreement with experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Feasibility of full-core pin resolved CFD simulations of small modular reactor with momentum sources

Complex flow structure interactions and heat transfer processes take place in nuclear reactor cores. Given the extreme pressure/temperature and radioactive conditions inside the core, numerical simulations offer an attractive and sometimes more feasible approach to study the related flow and heat transfer phenomena in addition to the experiments. Under the Exascale Computing Project, the full-core simulation of a small modular reactor (SMR) has been pursued coupling Computational Fluid Dynamics (CFD) and neutronics. A key aspect of the modeling of SMR fuel assemblies is the presence of spacer grids and the mixing promoted by mixing vanes or the equivalent. A reduced order methodology is adopted based on momentum sources to mimic the mixing of the vanes. The momentum sources have been carefully calibrated with detailed Large Eddy Simulations (LES) of spacer grids performed with Nek5000. Modeling the spacer grid and mixing vanes (SGMV) effect without body-fitted computational grid avoids the excessive costs in resolving the local geometric details, and thus supports the simulation to be scaled up to the full core. Besides the progress on momentum source modeling, this paper also features the first full-core pin resolved CFD simulation ever performed to the authors' knowledge. This represents a significant advancement in capability for the CFD of nuclear reactors, which will hopefully serve as an inspiration for further integrating high-fidelity numerical simulations in actual engineering designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗