Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Speed Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Evaluation of Geopolymer Concrete for Rocket Test Facility Flame Deflectors

The current paper presents results from a combined research effort by Louisiana Tech University (LTU) and NASA Stennis Space Center (SSC) to develop a new alumina-silicate based cementitious binder capable of acting as a high performance refractory material with low heat ablation rate and high early mechanical strength. Such a binder would represent a significant contribution to NASA's efforts to develop a new generation of refractory 'hot face' liners for liquid or solid rocket plume environments. This project was developed as a continuation of on-going collaborations between LTU and SSC, where test sections of a formulation of high temperature geopolymer binder were cast in the floor and walls of Test Stand E-1 Cell 3, an active rocket engine test stand flame trench. Additionally, geopolymer concrete panels were tested using the NASA-SSC Diagnostic Test Facility (DTF) thruster, where supersonic plume environments were generated on a 1ft wide x 2ft long x 6 inch deep refractory panel. The DTF operates on LOX/GH2 propellants producing a nominal thrust of 1,200 lbf and the combustion chamber conditions are Pc=625psig, O/F=6.0. Data collected included high speed video of plume/panel area and surface profiles (depth) of the test panels measured on a 1-inch by 1-inch giving localized erosion rates during the test. Louisiana Tech conducted a microstructure analysis of the geopolymer binder after the testing program to identify phase changes in the material.

Allgood, Daniel C.↗

Comparison of Computational Results with a Low-g, Nitrogen Slosh and Boiling Experiment

This paper compares a fluid/thermal simulation, in Fluent, with a low-g, nitrogen slosh and boiling experiment. In 2010, the French Space Agency, CNES, performed cryogenic nitrogen experiments in a low-g aircraft campaign. From one parabolic flight, a low-g interval was simulated that focuses on low-g motion of nitrogen liquid and vapor with significant condensation, evaporation, and boiling. The computational results are compared with high-speed video, pressure data, heat transfer, and temperature data from sensors on the axis of the cylindrically shaped tank. These experimental and computational results compare favorably. The initial temperature stratification is in good agreement, and the two-phase fluid motion is qualitatively captured. Temperature data is matched except that the temperature sensors are unable to capture fast temperature transients when the sensors move from wet to dry (liquid to vapor) operation. Pressure evolution is approximately captured, but condensation and evaporation rate modeling and prediction need further theoretical analysis.

Cryogenic Fluid Storage↗

Space Launch System Base Heating Test: Environments and Base Flow Physics

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen-hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during flight. Due to the complex nature of rocket plume-induced flows within the launch vehicle base during ascent and a new vehicle configuration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot-fire test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate flight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative effort that has not been attempted in 40+ years for a NASA vehicle. This paper discusses the various trends of base convective heat flux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base flow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi-empirical numerical models to determine exceedance and conservatism of the flight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Mehta, Manish↗

Investigation of Non-Equilibrium Radiation for Earth Entry

This paper presents measurements and simulations of non-equilibrium shock layer radiation relevant to high-speed Earth entry data obtained in the NASA Ames Research Center's Electric Arc Shock Tube (EAST) facility. The experiments were aimed at measuring the spatially and spectrally resolved radiance at relevant entry conditions for both an approximate Earth atmosphere (79 N2 : 21 O2) as well as a more accurate composition featuring the trace species Ar and CO2 (78.08 N2 : 20.95 O2 : 0.04 CO2 : 0.93 Ar). The experiments were configured to target a wide range of conditions, of which shots from 8 to 11.5 km/s at 0.2 Torr (26.7 Pa) are examined in this paper. The non-equilibrium component was chosen to be the focus of this study as it can account for a significant percentage of the emitted radiation for Earth entry, and more importantly, non-equilibrium has traditionally been assigned a large uncertainty for vehicle design. The main goals of this study are to present the shock tube data in the form of a non-equilibrium metric, evaluate the level of agreement between the experiment and simulations, identify key discrepancies and to promote discussion about various aspects of modeling non-equilibrium radiating flows. Radiance profiles integrated over discreet wavelength regions, ranging from the VUV through to the NIR, were compared in order to maximize both the spectral coverage and the number of experiments that could be used in the analysis. A previously defined non-equilibrium metric has been used to allow comparisons with several shots and reveal trends in the data. Overall, LAURAHARA is shown to under-predict EAST by as much as 50 and over-predict by as much as 20 depending on the shock speed. DPLRNEQAIR is shown to under-predict EAST by as much as 40 and over-predict by as much as 12 depending on the shock speed. In terms of an upper bound estimate for the absolute error in wall-directed heat flux, at the lower speeds investigated in this paper, 8 to 9 km/s, even though there are some large relative differences, the absolute error in radiance will be less then 1 Wcm2. At the highest shock speed of 11 km/s, the error will be less than 20 W/ sq cm.

Radiation↗

Space Launch System Base Heating Test: Environments and Base Flow Physics

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen- hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during ight. Due to the complex nature of rocket plume-induced ows within the launch vehicle base during ascent and a new vehicle con guration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot- re test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate ight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative e ort that has not been attempted in 40+ years for a NASA vehicle. This presentation discusses the various trends of base convective heat ux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base ow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi- empirical numerical models to determine exceedance and conservatism of the ight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Mehta, Manish↗

Predicting the Penetration of a Shielded TPS Tile

All spacecraft are subject to the possibility of high-speed particle impacts during their mission life. In low earth orbit, those impacts could be the result of collisions with pieces of orbital debris or with meteorites. Beyond LEO, and especially beyond GEO, those impacts will likely be caused by meteorites. Such high-speed impacts on spacecraft surfaces create debris clouds that travel towards and eventually impact other downstream spacecraft components. In addition to the impulsive load that such debris clouds would impart to the spacecraft elements with which they subsequently collide, the largest fragment in these debris clouds poses a significant threat on its own to those spacecraft elements. In order to be able to assess the severity of the threat posed by such a fragment, it is important to be able to predict the extent of damage sustained by the impacted spacecraft element. In this paper, we present a new process for determining the penetration depth in a shielded TPS tile system. The requirements for the process were that it be applicable across a full spectrum of impact low velocities (i.e. from ~ 7 km/s to above 50 km/s), that it be applicable over a wide range of projectile materials densities (i.e. ranging from water to steel, for example), and that it be applicable over a wide range of trajectory obliquities (i.e. not just normal impacts). Furthermore, the process developed should be sufficiently flexible so that it can be used for shield design parameter and / or system configuration trade studies (i.e. be written in terms of as many shield and TPS tile system parameters as possible). Following the initial impact of the projectile on the outer wall of the dual-wall shield, a debris cloud (i.e. the primary debris cloud) is created that travels towards and impacts the inner wall of the shield. Within this debris cloud is a combination of solid, liquid, and vaporized material, depending on the impact velocity and the impedance mismatch of the projectile and outer wall materials. The impact of this debris cloud on the inner wall creates another debris cloud (i.e. the secondary debris cloud) that then travels towards and impacts the TPS tile. Within the particulate distribution of the material in each of these debris clouds is a so-called largest fragment. The process used to calculate the penetration depth in a shielded TPS tile system developed herein consists of the following three steps: 1. Does the initial projectile perforate the outer wall of the shield? If NO, the TPS tile remains undamaged. If YES, calculate the size and speed of the largest fragment exiting the outer wall of the shield and traveling towards the shield’s inner wall. 2. Does the largest fragment in the debris cloud exiting the outer wall of the shield perforate the inner wall of the shield? If NO, the TPS tile again remains undamaged. If YES, calculate the size and speed of the largest fragment exiting the rear of the shield inner wall. 3. Calculate the penetration depth of the largest fragment in the debris cloud exiting the inner wall into the TPS. Perforation of the inner and outer shield walls is predicted using the Cour-Palais penetration depth equation and an associated failure criterion [1]. The largest debris cloud fragment diameters and associated velocities are calculated using regression equations developed from a mix of hydrocode and experimental diameter and velocity information [2]. Finally, TPS penetration depths are calculated using an empirical penetration depth predictor equation based on high-speed impact test data and are calibrated using a limited number of hydrocode penetration depth predictions for water, nylon, aluminum, Dunite, and steel projectiles The predictions of the penetration depth calculation process are compared against the predictions of more than 60 SPHC hydrocode runs. These comparisons show that the process used to calculate TPS tile penetration depths usually yields values that are within 1 mm of the predictions of hydrocode simulations. If a maximum allowable TPS penetration depth is known, the process developed herein can now be used to develop a failure limit equation that would predict whether or not an impacting particle would penetrate deeply enough into the TPS to result in a “failed” or “not failed” end state. References [1] E.L. Christiansen, “Design and performance equations for advanced meteoroid and debris shields”, International Journal of Impact Engineering, Vol. 14, 1993, pp. 145-156. [2] W.P. Schonberg, “Predicting the size of the largest particle fragment in a debris cloud created by an orbital debris impact and its associated velocity”, 2021 Applied Space Environments Conference, NASA Jet Propulsion Laboratory, Pasadena, California, November, 2021.

Meteroid↗

Extending the Applicability of Thermal Protection System Ballistic Limit Equations Beyond the Testable Regime

All spacecraft use some sort of thermal insulation in their design, which is usually placed on the spacecraft’s exterior. As such, it is highly susceptible to high-speed impacts by meteoroids and orbital debris. These high-speed impacts can damage the insulation to a point where the protection it offers is below acceptable limits. It is, therefore, important to be able to characterize expected TPS damage levels stemming from such high-speed impacts. In a recent paper, we presented the results of a study that sought to characterize the high-speed impact damage that would be sustained by two thermal protection materials that have recently gained attention for possible use in interplanetary missions. As part of the analyses performed, ballistic limit equations for these materials were developed using recent high-speed impact test data, and then assessed by comparing their predictions against test data. In this paper, we extend the applicability of the ballistic limit equation for one of those thermal materials beyond the testable regime using the results of series of Smooth Particle Hydrodynamics Code (SPHC) impact simulations at velocities in excess of 10 km/s. When the predictions of the updated and expanded BLE were compared against the results of the SPHC runs, the predictions were seen to be consistent with the data: non-perforation data points were typically below the BLE curves, while perforation data points were typically above them.

Thermal Protection System↗

R&D studies of the ATLAS LAr calorimeter readout electronics for super-LHC

The ATLAS Liquid Argon (LAr) calorimeters are high precision, high sensitivity and high granularity detectors. A total of 182,468 signals are digitized and processed real-time on detector, to provide energy and time deposited in each detector element at every occurrence of the L1-trigger. The current readout electronics will need to be upgraded to sustain the higher radiation levels expected with the increase of a factor 10 in luminosity at the LHC in the years {approx}2017. A completely innovative readout scheme is being developed. The front-end readout will send out data continuously at each bunch crossing through high speed radiation resistant optical links, the data will be processed real-time with the possibility of implementing trigger algorithms. This article is an overview of the R&D activities and architectural studies the ATLAS LAr Calorimeter Group is developing: front-end analog and mixed-signal ASIC design, radiation resistance optical-links in SOS, high-speed back-end processing units based on FPGA architectures and power supply distribution schemes.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Local and transient nanoscale strain mapping during in situ deformation

The mobility of defects such as dislocations controls the mechanical properties of metals. This mobility is determined both by the characteristics of the defect and the material, as well as the local stress and strain applied to the defect. Therefore, the knowledge of the stress and strain during deformation at the scale of defects is important for understanding fundamental deformation mechanisms. In this paper, we demonstrate a method of measuring local stresses and strains during continuous in situ deformation with a resolution of a few nanometers using nanodiffraction strain mapping. Finally, our results demonstrate how large multidimensional data sets captured with high speed electron detectors can be analyzed in multiple ways after an in situ TEM experiment, opening the door for true multimodal analysis from a single electron scattering experiment.

36 MATERIALS SCIENCE↗

The Development of an Airborne Information Management System for Flight Test

An airborne information management system is being developed at the NASA Dryden Flight Research Facility. This system will improve the state of the art in management data acquisition on-board research aircraft. The design centers around highly distributable, high-speed microprocessors that allow data compression, digital filtering, and real-time analysis. This paper describes the areas of applicability, approach to developing the system, potential for trouble areas, and reasons for this development activity. System architecture (including the salient points of what makes it unique), design philosophy, and tradeoff issues are also discussed.

Liquid cooling↗

The Development of an Airborne Information Management System for Flight Test

An airborne information management system is being developed at the NASA Dryden Flight Research Facility. This system will improve the state of the art in management data acquisition on-board research aircraft. The design centers around highly distributable, high-speed microprocessors that allow data compression, digital filtering, and real-time analysis. This paper describes the areas of applicability, approach to developing the system, potential for trouble areas, and reasons for this development activity. System architecture (including the salient points of what makes it unique), design philosophy, and tradeoff issues are also discussed.

Flight Testing↗

Client/Server data serving for high performance computing

This paper will attempt to examine the industry requirements for shared network data storage and sustained high speed (10's to 100's to thousands of megabytes per second) network data serving via the NFS and FTP protocol suite. It will discuss the current structural and architectural impediments to achieving these sorts of data rates cost effectively today on many general purpose servers and will describe and architecture and resulting product family that addresses these problems. The sustained performance levels that were achieved in the lab will be shown as well as a discussion of early customer experiences utilizing both the HIPPI-IP and ATM OC3-IP network interfaces.

Wood, Chris↗

X-ray bright points and high-speed wind streams: A preliminary analysis from Yohkoh and Ulysses data

The following aspect of the solar wind mass flux, and of its variation, is examined: whether coronal plumes might be responsible for the long-term variability of the mass flux in high-speed streams emanating from coronal holes. The assumption that plumes are rooted in coronal bright points (BP's) is made. The behavior of X-ray BP's, imaged by the Yohkoh soft X-ray telescope (SXT), during a seven month period when Ulysses experiments observed a series of recurrent high-speed streams, is analyzed. If plumes/BP's are sources of the wind mass flux, changes in the coronal hole BP density to mimic changes of the mass flux in high-speed streams are expected. SOHO will have the capability of measuring the solar wind speed/density at small heliocentric distances while simultaneously observing coronal BP's and coronal plumes.

Poletto, Giannina↗

Optical Communications and Sensor Demonstration

The Optical Communications and Sensor Demonstration (OCSD) project addresses two cross-cutting capabilities of value to many future small spacecraft missions: high-speed optical transmission of data and small spacecraft proximity operations. Optical data rates demonstrated by OCSD are expected to be 200 megabits persecond (Mbs) or higher, a factor of 100 increase over current high-end CubeSat communications systems. The proximity sensors developed for this mission enable relative position measurement between two small satellites - a capability not previously demonstrated.

High-speed optical transmission of data↗

Fast Asynchronous Data Communication Via Fiber Optics

Transmitter and receiver devised for asynchronous digital communication via optical fiber at rates above 100 Mb/s. Transmitter converts parallel data to serial for high-speed transmission; receiver recovers clock signal and converts data back to parallel. No phase-lock loops used. New receiver design avoids over-sampling altogether. Local sampling oscillator operating nominally at clock frequency generates N clock signals of equally spaced phase, used to clock incoming data into N separate shift registers.

Bergman, Larry A.↗

Enabling Earth Science: The Facilities and People of the NCCS

The NCCS's mass data storage system allows scientists to store and manage the vast amounts of data generated by these computations, and its high-speed network connections allow the data to be accessed quickly from the NCCS archives. Some NCCS users perform studies that are directly related to their ability to run computationally expensive and data-intensive simulations. Because the number and type of questions scientists research often are limited by computing power, the NCCS continually pursues the latest technologies in computing, mass storage, and networking technologies. Just as important as the processors, tapes, and routers of the NCCS are the personnel who administer this hardware, create and manage accounts, maintain security, and assist the scientists, often working one on one with them.

Source record↗

A high-speed photonic clock and carrier regenerator

As data communications rates climb toward 10 Gbits/s, clock recovery and synchronization become more difficult, if not impossible, using conventional electronic circuits. The high-speed photonic clock regenerator described in this article may be more suitable for such use. This photonic regenerator is based on a previously reported photonic oscillator capable of fast acquisition and synchronization. With both electrical and optical clock inputs and outputs, the device is easily interfaced with fiber-optic systems. The recovered electrical clock can be used locally and the optical clock can be used anywhere within a several kilometer radius of the clock/carrier regenerator.

Yao, X. S.↗