Search NASA⌕ Search

SEARCH · Search NASA

Results for “INDUCTIVE CHARGING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Unintended gas breakdowns in narrow gaps of advanced plasma sources for semiconductor fabrication industry

Occurrence of unintended gas breakdown in the narrow gaps of plasma processing chambers is one of the critical challenges in developing advanced plasma sources. Here, we present a combined experimental and theoretical study of unintended discharges in the narrow gaps of plasma processing chambers and report significant drop of the gas breakdown voltage in the presence of a background plasma facing the gap. Experimentally measured breakdown voltages decrease in subsequent breakdown events due to wall erosion caused by the discharge. Therefore, preventing and mitigating the first discharge is of paramount importance. An analysis of kinetic simulation results indicates that the charged particle influx from the background plasma in the processing chamber into the gap is responsible for the onset of early breakdown: higher charged particle density within the gap modifies the electric field profile, allowing unintended breakdowns to occur at a significantly reduced threshold voltage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sensitivity Analysis of a Wireless Power Transfer (WPT) System for Electric Vehicle Application

This paper presents a detailed parametric sensitivity analysis for a wireless power transfer (WPT) system in electric vehicle application. Specifically, several key parameters for sensitivity analysis of a series-parallel (SP) WPT system are derived first based on analytical modeling approach, which includes the equivalent input impedance, active / reactive power, and DC voltage gain. Based on the derivation, the impact of primary side compensation capacitance, coupling coefficient, transformer leakage inductance, and different load conditions on the DC voltage gain curve and power curve are studied and analyzed. It is shown that the desired power can be achieved by just changing frequency or voltage depending on the design value of coupling coefficient. However, in some cases both have to be modified in order to achieve the required power transfer.

electric vehicle↗

Correlation between surface chemistry and ion energy dependence of the etch yield in multicomponent oxides etching

The influence of surface chemistry in plasma etching of multicomponent oxides was investigated through measurements of the ion energy dependence of the etch yield. Using pulsed-laser-deposited Ca{sub x}Ba{sub (1-x)}Nb{sub 2}O{sub 6} (CBN) and SrTiO{sub 3} thin films as examples, it was found that the etching energy threshold shifts toward values larger or smaller than the sputtering threshold depending on whether or not ion-assisted chemical etching is the dominant etching pathway and whether surface chemistry is enhancing or inhibiting desorption of the film atoms. In the case of CBN films etched in an inductively coupled Cl{sub 2} plasma, it is found that the chlorine uptake is inhibiting the etching reaction, with the desorption of nonvolatile NbCl{sub 2} and BaCl{sub 2} compounds being the rate-limiting step.

36 MATERIALS SCIENCE↗

Cold atmospheric plasma in cancer therapy

Recent progress in atmospheric plasmas has led to the creation of cold plasmas with ion temperature close to room temperature. This paper outlines recent progress in understanding of cold plasma physics as well as application of cold atmospheric plasma (CAP) in cancer therapy. Varieties of novel plasma diagnostic techniques were developed recently in a quest to understand physics of CAP. It was established that the streamer head charge is about 10{sup 8} electrons, the electrical field in the head vicinity is about 10{sup 7} V/m, and the electron density of the streamer column is about 10{sup 19} m{sup −3}. Both in-vitro and in-vivo studies of CAP action on cancer were performed. It was shown that the cold plasma application selectively eradicates cancer cells in-vitro without damaging normal cells and significantly reduces tumor size in-vivo. Studies indicate that the mechanism of action of cold plasma on cancer cells is related to generation of reactive oxygen species with possible induction of the apoptosis pathway. It is also shown that the cancer cells are more susceptible to the effects of CAP because a greater percentage of cells are in the S phase of the cell cycle.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

AN IMPLICIT"DRIFT-LORENTZ" PARTICLE MOVER FOR PLASMA AND BEAM SIMULATIONS

In order to efficiently perform particle simulations in systems with widely varying magnetization, we developed a drift-Lorentz mover, which interpolates between full particle dynamics and drift kinetics in such a way as to preserve a physically correct gyroradius and particle drifts for both large and small ratios of the timestep to the cyclotron period. In order to extend applicability of the mover to systems with plasma frequency exceeding the cyclotron frequency such as one may have with fully neutralized drift compression of a heavy-ion beam we have developed an implicit version of the mover. A first step in this direction, in which the polarization charge was added to the field solver, was described previously. Here we describe a fully implicit algorithm (which is analogous to the direct-implicit method for conventionalparticle-in-cell simulation), summarize a stability analysis of it, and describe several tests of the resultant code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NEWLY BORN PULSARS AS SOURCES OF ULTRAHIGH ENERGY COSMIC RAYS

Newly born pulsars offer favorable sites for the injection of heavy nuclei, and for their further acceleration to ultrahigh energies. Once accelerated in the pulsar wind, nuclei have to escape from the surrounding supernova envelope. We examine this escape analytically and numerically and discuss the pulsar source scenario in light of the latest ultrahigh energy cosmic ray (UHECR) data. Our calculations show that, at early times, when protons can be accelerated to energies E > 10{sup 20} eV, the young supernova shell tends to prevent their escape. In contrast, because of their higher charge, iron-peaked nuclei are still accelerated to the highest observed energies at later times, when the envelope has become thin enough to allow their escape. Ultrahigh energy iron nuclei escape newly born pulsars with millisecond periods and dipole magnetic fields of {approx}10{sup 12}-10{sup 13} G, embedded in core-collapse supernovae. Due to the production of secondary nucleons, the envelope crossing leads to a transition of composition from light to heavy elements at a few EeV, as observed by the Auger Observatory. The escape also results in a softer spectral slope than that initially injected via unipolar induction, which allows for a good fit to the observed UHECR spectrum. We conclude that the acceleration of iron-peaked elements in a reasonably small fraction ({approx}< 0.01%) of extragalactic rotation-powered young pulsars would reproduce satisfactorily the current UHECR data. Possible signatures of this scenario are also discussed.

79 ASTRONOMY AND ASTROPHYSICS↗

Three point method to characterize low-pressure electronegative discharges using electrostatic probe

Electrostatic probe measurements for low-pressure inductively coupled SF{sub 6} plasmas are performed. From the current-voltage (I-V) curves of probe, the saturation currents of the positive ions and electrons and the electron temperature are measured. The electronegativity and the negative ion density are deduced by using the ratios of these parameters at three adjacent pressure points. The positive ion density is calculated by the orbital-motion-limited theory, and the electron temperatures are given either by the slope of the I-V curves or by the electron energy distribution function with the second derivative of I-V curves. The variations in the charged species density with pressure and power are investigated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Inductive Measurement of Plasma Jet Electrical Conductivity

An inductive probing scheme, originally developed for shock tube studies, has been adapted to measure explosive plasma jet conductivities. In this method, the perturbation of an applied magnetic field by a plasma jet induces a voltage in a search coil, which, in turn, can be used to infer electrical conductivity through the inversion of a Fredholm integral equation of the first kind. A 1-inch diameter probe was designed and constructed, and calibration was accomplished by firing an aluminum slug through the probe using a light-gas gun. Exploratory laboratory experiments were carried out using plasma jets expelled from 15-gram high explosive shaped charges. Measured conductivities were in the range of 3 kS/m for unseeded octol charges and 20 kS/m for seeded octol charges containing 2% potassium carbonate by mass.

Turner, Matthew W.↗

LA-R43S6-L1 Postshot Report [Slides]

The Ranchero LA-R43S6-L1 test (formerly referred to as LA-43S-L1. The R specifically designates it is a Ranchero device and the 6 indicates a 6” high explosive charge diameter in anticipation of using larger diameters in the future.) was conducted on 3/8/17 with good success. The experiment was the first test of a “Swooped” Ranchero flux compression generator (FCG), and the load for the test was an aluminum imploding liner. In addition to the swoop, the stator was anodized to provide an insulating layer instead of one or more layers of polyethylene as had been the case for all earlier Ranchero tests. Using the Firing point TA-39-88 capacitor bank, 3.5 MA was delivered to the FCG for the initial magnetic field, and 36.4 MA were delivered to the load having an initial inductance of 2.5 nH. Implosion speeds over 1.1 cm/us were recorded, which exceeds previous LANL solid liner experimental results. The test was diagnosed with 18 PDV channels, 12 of which recorded liner implosion data, and the other 6 of which tracked the FCG armature during flux compression. These armature expansion data recorded during flux compression are the first of their kind, and it was previously unknown, due to unknown effects of the SF 6 in the flux compression volume, whether or not the expansion could be recorded using the PDV technique. Post shot 2D MHD calculations employed a complete external circuit model, and an improved flux diffusion model not available prior to the test. Results from these simulations show very good agreement with the experimental result. Four PDV channels recorded the liner implosion viewed radially outward from the center of the liner. All four of these probes recorded implosion velocities greater that 1 cm/µs, with the cylindrical center displaced by ~2 mm from actual center. Four PDV channels looked at +10° angles from the CMU wall, and four looked at -10° angles. A glide plane interaction is shown moving toward the center of the liner in MHD calculations, and PDV probes provide confirmation. The high explosive (HE) in the LA-R43S6-L1 test was PBX 9501 which had to be glued together in many pieces, and the test was preceded by a camera test to verify that the PBX 9501 could be assembled with acceptable tolerance in glue joints to prevent severing the armature during expansion. The camera test verified an acceptable armature performance, and results are given in complete detail in a post shot report LA-UR-19-20124, and summarized here. This report provides complete detail of the considerable body of data obtained on the test and in the post shot calculations. It is prepared in Power Point for ease of preparation and future review. Shot documentation available in the LANL on-line library are included as references, and non-referenceable documents will be cited and stored in an LA- R43S6-L1 post shot folder stored on an M-6 shared drive. Fabrication drawings are also maintained in an M-6 shared drive and paper files are available from M-6 personnel. This report will be maintained as a PowerPoint document on the shared drive, as well, since included movies will play and graphs from Excel files retain information in the PowerPoint versions. PDF versions are required for clearance and are not to large to send by e-mail.

42 ENGINEERING↗

Impulsive plasma transport through the magnetopause

The considered investigation is concerned with a study of the process of localized plasma entry on the basis of first principles. Since the magnetopause often moves at high velocities, an induction electric field must be involved. Attention is given to the case in which the adjacent magnetopause is at rest. Occasionally, a frame moving with the magnetopause in the interaction region is also considered. The employed model is based on the observations provided by ISEE. The considered plasma irregularity, which is denominated a 'cloud', may not have to be a large enhancement in number density or velocity. An examination of the involved physical relations shows that the plasma will create its own electric field, via a polarization current, to make possible a penetration through the magnetopause by the cloud. At the magnetopause the polarization current creates a charge separation electric field which promotes (rather than inhibits) continued flow through the moving magnetopause.

Heikkila, W. J.↗

ASSESMENT OF IMPURITIES IN NP METAL USING DOUBLE-FOCUSING SF-ICP-MS

In the transmutation process, minor actinides such as neptunium, americium and curium obtained from spent nuclear fuel are incorporated into new fuel that can be placed into a fast reactor, where these elements fission into products with shorter half-lives which reduces the health and safety hazards [1]. In order to better understand the all the involved processes, fundamental physical properties of actinides should be investigated, and for that reason, high-purity materials need to be produced. One of the main challenges in characterizing these materials is the lack of pure metal available for study, and lack of analytical methods to determine the purity. Trans-uranic elements are challenging to study because of the need to be handled in specialized facilities, safeguards concerns and they are not easily purchased and/or produced. High-purity Np metal is being produced at the Materials and Fuels Complex (MFC) of Idaho National Laboratory (INL), in a process of direct oxide reduction developed by Squires and Lessing [2], with a target purity of 99.999%. The goal of this research is to develop methods to determine the impurities in the Np metal, with detection limits low enough to achieve this purity level. In this work, we have used several ICP-MS and ICP OES techniques, but the focus was the method development using a recently acquired Double-Focusing Sector Field Inductively Coupled Plasma Mass Spectrometer (SF-ICP-MS). To produce the Np metal, approximately 20 g of the neptunium oxide powder was calcined at 800 oC for 6 h in a magnesium oxide crucible, which is placed inside a stainless steel crucible, that goes into the Hot Uniaxial Press (HUP) furnace insert. After the calcining step, the Np oxide was mixed with approximately 9 g of calcium metal and 100 g of ultra-dry calcium chloride. The HUP furnace was heated in a ramp rate of 50 oC min -1 up to 1000 oC. When the reaction mixture reached 850 oC, a tantalum stirrer was activated at 100 rpm. After the tantalum stirrer was removed and the mixture cooled overnight, the MgO crucible was opened with a hammer and chisel to retrieve the Np metal button at the bottom of the reaction mixture [2]. Prior to the dissolution process, the surface contaminants of the sample were removed. The Np button was washed in 10 mL of ultra-pure water for 1 min, with a faint reaction observed on the surface, indicating the presence of Ca metal. The water-washed sample was placed in a tube with 2 M HCl for only 3 s, as a vigorous reaction in the button surface was observed. The leachates were saved for further analysis. The sample was then rinsed with ultra-pure water and air-dried prior to dissolution. The cleaned sample was placed in a PTFE beaker and 25 mL of 6 M HCl and 150 µL of 24 M HF were added. After 10 minutes of reaction, the beaker was placed on a hot plate for 1 h and 30 min, followed by the addition of 1 mL of 16 M HNO3 and allowed to react for a further 1 h and 20 min. The sample was removed from heat and 10 mL of HNO3 16 M was added to react with the HCl. The beaker was covered and left for overnight reaction, producing a solution with approximately 20 mL of final volume. A Quadrupole Inductively Coupled Plasma Mass Spectrometer (Q-ICP-MS, Perkin Elmer ELAN DRC II Q-ICP-MS) was used to obtain qualitative mass spectra for the dissolution blank, each of the leachates and the dissolved sample. In the water leachate spectrum mainly Ca and Mg were observed, while the acid wash had a similar peak pattern to the one observed for the Np metal sample, indicating that the process not only removed surface contamination, but also reacted with the sample itself. In the Np material spectrum, Ta and actinides were identified as candidates for major contaminants, as the most intense peaks corresponded to the mass-to-charge ratios of these elements. Minor contaminants included Al, Au, Ca, Cr, Fe, I, Na, Nb, Pb, Sn, Ti, Tl, V, Y. The presence of impurities in the material could have originated from several sources, such as the materials used for the casting process, the use of impure NpO2 or contamination of reagents and materials used for the analysis. Some of the isotopes listed as potential contaminants are susceptible to spectral interferences, so Double-Focusing SF-ICP-MS (Nu Instruments Attom ES HR-ICP-MS) was used for the quantitative analysis. For each isotope determined, several items were evaluated: raw signal of a blank solution, sensitivity and determination coefficient of calibration curves, possibility of interferences and comparison of results obtained for at least two resolving powers (RP): 300 and 4000. The evaluation of the signal in a blank solution can indicate if a spectral interference from the plasma gas and/or the solvent was successfully resolved (commonly observed for 52Cr+/40Ar12C+, for example). It is important to highlight that a signal reduction is expected when a higher RP is used, as the ion beam transmission is decreased by the use of na

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessment of Impurities in Neptunium Metal Using Double-Focusing SF-ICP-MS

In the transmutation process, minor actinides such as neptunium, americium and curium obtained from spent nuclear fuel are incorporated into new fuel that can be placed into a fast reactor, where these elements fission into products with shorter half-lives which reduces the health and safety hazards. In order to better understand the all the involved processes, fundamental physical properties of actinides should be investigated, and for that reason, high-purity materials need to be produced. One of the main challenges in characterizing these materials is the lack of pure metal available for study, and lack of analytical methods to determine the purity. Trans-uranic elements are challenging to study because of the need to be handled in specialized facilities, safeguards concerns and they are not easily purchased and/or produced. High-purity Np metal is being produced at the Materials and Fuels Complex (MFC) of Idaho National Laboratory (INL), in a process of direct oxide reduction developed by Squires and Lessing, with a target purity of 99.999%. The goal of this research is to develop methods to determine the impurities in the Np metal, with detection limits low enough to achieve this purity level. In this work, we have used several ICP-MS and ICP OES techniques, but the focus was the method development using a recently acquired Double-Focusing Sector Field Inductively Coupled Plasma Mass Spectrometer (SF-ICP-MS). To produce the Np metal, approximately 20 g of the neptunium oxide powder was calcined at 800 oC for 6 h in a magnesium oxide crucible, which is placed inside a stainless steel crucible, that goes into the Hot Uniaxial Press (HUP) furnace insert. After the calcining step, the Np oxide was mixed with approximately 9 g of calcium metal and 100 g of ultra-dry calcium chloride. The HUP furnace was heated in a ramp rate of 50 oC min -1 up to 1000 oC. When the reaction mixture reached 850 oC, a tantalum stirrer was activated at 100 rpm. After the tantalum stirrer was removed and the mixture cooled overnight, the MgO crucible was opened with a hammer and chisel to retrieve the Np metal button at the bottom of the reaction mixture. Prior to the dissolution process, the surface contaminants of the sample were removed. The Np button was washed in 10 mL of ultra-pure water for 1 min, with a faint reaction observed on the surface, indicating the presence of Ca metal. The water-washed sample was placed in a tube with 2 M HCl for only 3 s, as a vigorous reaction in the button surface was observed. The leachates were saved for further analysis. The sample was then rinsed with ultra-pure water and air-dried prior to dissolution. The cleaned sample was placed in a PTFE beaker and 25 mL of 6 M HCl and 150 µL of 24 M HF were added. After 10 minutes of reaction, the beaker was placed on a hot plate for 1 h and 30 min, followed by the addition of 1 mL of 16 M HNO3 and allowed to react for a further 1 h and 20 min. The sample was removed from heat and 10 mL of HNO3 16 M was added to react with the HCl. The beaker was covered and left for overnight reaction, producing a solution with approximately 20 mL of final volume. A Quadrupole Inductively Coupled Plasma Mass Spectrometer (Q-ICP-MS, Perkin Elmer ELAN DRC II Q-ICP-MS) was used to obtain qualitative mass spectra for the dissolution blank, each of the leachates and the dissolved sample. In the water leachate spectrum mainly Ca and Mg were observed, while the acid wash had a similar peak pattern to the one observed for the Np metal sample, indicating that the process not only removed surface contamination, but also reacted with the sample itself. In the Np material spectrum, Ta and actinides were identified as candidates for major contaminants, as the most intense peaks corresponded to the mass-to-charge ratios of these elements. Minor contaminants included Al, Au, Ca, Cr, Fe, I, Na, Nb, Pb, Sn, Ti, Tl, V, Y. The presence of impurities in the material could have originated from several sources, such as the materials used for the casting process, the use of impure NpO2 or contamination of reagents and materials used for the analysis. Some of the isotopes listed as potential contaminants are susceptible to spectral interferences, so Double-Focusing SF-ICP-MS (Nu Instruments Attom ES HR-ICP-MS) was used for the quantitative analysis. For each isotope determined, several items were evaluated: raw signal of a blank solution, sensitivity and determination coefficient of calibration curves, possibility of interferences and comparison of results obtained for at least two resolving powers (RP): 300 and 4000. The evaluation of the signal in a blank solution can indicate if a spectral interference from the plasma gas and/or the solvent was successfully resolved (commonly observed for 52Cr+/40Ar12C+, for example). It is important to highlight that a signal reduction is expected when a higher RP is used, as the ion beam transmission is decreased by the use of narrower slits

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Supramolecular Assembly of Lanthanide-Binding Tag Peptides for Aqueous Separation of Rare Earth Elements

Selective and eco-friendly separation and purification methods for rare earth elements (REEs) are necessary to meet the increasing demand for these valuable metals, which are extensively used in modern electronics and clean energy technologies. Mining feedstocks consist of REE mixtures as stable trivalent cations (Ln 3+ ) that are difficult to separate due to their identical charge and similar size. Lanthanide-binding tags (LBTs), peptide chelates that coordinate Ln 3+ in binding pockets, show promise as selective, high-affinity extractants. We demonstrate that the LBT variant LBTLLA 5– , designed for high selectivity for Tb 3+ , is an effective extractant, forming complexes with REEs in solution that subsequently organize into self-assembling structures rich in Ln 3+ . These structures condense into aggregates that can be separated, enabling an efficient, all-aqueous, eco-friendly separation process. The self-assembled structures are studied using dynamic light scattering, ζ-potential measurements, transmission electron microscopy, anomalous small-angle X-ray scattering, inductively coupled plasma optical emission spectroscopy, and ultraviolet–visible absorption spectroscopy, which confirm LBTLLA 5– peptide-REE ion binding and the further assembly of micron-scale structures rich in REEs. Molecular dynamics simulations reveal the interactions promoting aggregation as well as the integrity of the binding pocket upon self-assembly. We find that LBTLLA 5– :Ln 3+ complexes recruit excess cations within the macrostructures, and we demonstrate that aggregation and selective separation can be controlled by manipulating the metal-peptide ratio in solution. Furthermore, we demonstrate separation from equimolar mixtures of REE pairs Tb 3+ -Lu 3+ and Tb 3+ -La 3+ , supporting the application of LBT peptides as a platform for the selective separation of REEs.

LBT peptides↗

2 kV, 0.7 mΩ•cm2 Vertical Ga2O3 Superjunction Schottky Rectifier with Dynamic Robustness

We report the first experimental demonstration of a vertical superjunction device in ultra-wide bandgap (UWBG) Ga 2 O 3 . The device features 1.8 μm wide, 2×10 17 cm -3 doped n-Ga 2 O 3 pillars wrapped by the charge-balanced p-type nickel oxide (NiO). The sidewall NiO is sputtered through a novel self-align process. Benefited from the high doping in Ga 2 O 3 , the superjunction Schottky barrier diode (SJ-SBD) achieves a ultra-low specific on-resistance (R ON,SP ) of 0.7 mΩ•cm 2 with a low turn-on voltage of 1 V and high breakdown voltage (BV) of 2000 V. The R ON,SP ~BV trade-off is among the best in all WBG and UWBG power SBDs. The device also shows good thermal stability with BV > 1.8 kV at 175 °C. In the unclamped inductive switching tests, the device shows a dynamic BV of 2.2 kV and no degradation under 1.7 kV repetitive switching, verifying the fast acceptor depletion in NiO under dynamic switching. Such high-temperature and switching robustness are reported for the first time in a heterogeneous superjunction. These results show the great potential of UWBG superjunction power devices.

Qin, Yuan↗

Effect of gigaelectron volt Au-ion irradiation on the characteristics of ultrananocrystalline diamond films

The effect of 2.245 GeV Au-ion irradiation/postannealing processes on the electron field emission (EFE) properties of ultrananocrystalline diamond (UNCD) films was investigated. Au-ion irradiation with a fluence of around 8.4x10{sup 13} ions/cm{sup 2} is required to induce a large improvement in the EFE properties of the UNCD films. Postannealing the Au-ion irradiated films at 1000 deg. C for 1 h slightly degraded the EFE properties of the films but the resulting EFE behavior was still markedly superior to that of pristine UNCD films. Transmission electron microscopy examinations revealed that the EFE properties of the UNCD films are primarily improved by Au-ion irradiation/postannealing processes because of the formation of nanographites along the trajectory of the irradiating ions, which results in an interconnected path for electron transport. In contrast, the induction of grain growth process due to Au-ion irradiation in UNCD films is presumed to insignificantly degrade the EFE properties for the films as the aggregates are scarcely distributed and do not block the electron conducting path.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reticular Electronic Tuning of Porphyrin Active Sites in Covalent Organic Frameworks for Electrocatalytic Carbon Dioxide Reduction

Here, the electronic character of porphyrin active sites for electrocatalytic reduction of CO 2 to CO in a two-dimensional covalent organic framework (COF) was tuned by modification of the reticular structure. Efficient charge transport along the COF backbone promotes electronic connectivity between remote functional groups and the active sites and enables the modulation of the catalytic properties of the system. A series of oriented thin films of these COFs was found to reduce CO 2 to CO at low overpotential (550 mV) with high selectivity (faradaic efficiency of 87%) and at high current densities (65 mA/mg), a performance well beyond related molecular catalysts in regard to selectivity and efficiency. The catalysts are stable for more than 12 h without any loss in reactivity. X-ray absorption measurements on the cobalt L-edge for the modified COFs enable correlations between the inductive effects of the appended functionality and the electronic character of the reticulated molecular active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Achieving Balanced Crystallinity of Donor and Acceptor by Combining Blade‐Coating and Ternary Strategies in Organic Solar Cells

Abstract As a prototype tool for slot‐die coating, blade‐coating exhibits excellent compatibility with large‐area roll‐to‐roll coating. A ternary organic solar cell based on PBDB‐T:PTB7‐Th:FOIC blends is fabricated by blade‐coating and exhibits a power conversion efficiency of 12.02%, which is one of the highest values for the printed organic solar cells in ambient environment. It is demonstrated that blade‐coating can enhance crystallization of these three materials, but the degree of induction is different (FOIC > PBDB‐T > PTB7‐Th). Thus, the blade‐coated PBDB‐T:FOIC device presents much higher electron mobility than hole mobility due to the very high crystallinity of FOIC. Upon the addition of PTB7‐Th into the blade‐coated PBDB‐T:FOIC blends, the crystallinity of FOIC decreases together with the corresponding electron mobility, due to the better miscibility between PTB7‐Th and FOIC. The ternary strategy not only maintains the well‐matched crystallinity and mobilities, but also increases the photocurrent with complementary light absorption as well as the Förster resonant energy transfer. Furthermore, small domains with homogeneously distributed nanofibers are observed in favor of the exciton dissociation and charge transport. This combination of blade‐coating and ternary strategies exhibits excellent synergistic effect in optimizing morphology, showing great potential in the large‐area fabrication of highly efficient organic solar cells.

Zhang, Lin↗

Soft-Switching Solid-State Transformer With Reduced Conduction Loss

Solid-state transformers (SSTs) are a promising solution photovoltaic (PV), wind, traction, data center, battery energy storage system (BESS), and fast charging electric vehicle (EV) applications. The traditional SSTs are typically three-stage, i.e., hard-switching cascaded multilevel rectifiers and inverters with dual active bridge (DAB) converters, which leads to bulky passives, low efficiency, and high electromagnetic interference (EMI). This article proposes a new soft-switching solid-state transformer (S4T). The S4T has full-range zero-voltage switching (ZVS), electrolytic capacitor-less dc link, and controlled dv/dt, which reduces EMI. The S4T comprises two reverse-blocking current-source inverter (CSI) bridges, auxiliary branches for ZVS, and transformer magnetizing inductor as a reduced dc link with 60% ripple. Compared with the prior S4T, an effective change on the leakage inductance diode is made to reduce the number of the devices on the main power path by 20% for significant conduction loss saving and retain the same functionality of damping the resonance between the leakage and resonant capacitors and recycling trapped leakage energy. The conduction loss saving is crucial, being the dominating loss mechanism in SSTs. Importantly, the proposed single-stage SST not only holds the potential for high power density and high efficiency but also has full functionality, e.g., multiport dc loads integration, voltage regulation, and reactive power compensation, unlike the traditional single-stage matrix SST. The S4T can achieve single-stage isolated bidirectional dc–dc, ac–dc, dc–ac, or ac–ac conversion. It can also be configured input-series output-parallel (ISOP) in a modular way for medium-voltage (MV) grids. Hence, the S4T is a promising candidate for the SST. The full functionality, e.g., voltage buck–boost, multiport, etc., and the universality of the S4T for the dc–dc, dc–ac, and ac–ac conversion are verified through the simulations and experiments of two-port and three-port MV prototypes based on 3.3 kV SiC MOSFETs in dc–dc, dc–ac, and ac–ac modes at 2 kV.

14 SOLAR ENERGY↗