Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS - FUSELAGES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Bounds on thickness and loading noise of rotating blades and the favorable effect of blade sweep on noise reduction

The maxima of amplitudes of thickness and loading noise harmonics are established when the radial distribution of blade chord, thickness ratio, and lift coefficient is specified. It is first shown that only airfoils with thickness distribution and chordwise loading distributions which are symmetric with respect to midchord need be considered for finding the absolute maxima of thickness and loading noise. The resulting chordwise thickness and load distributions for these maximum noise conditions require infinite slope at some points along the chord but otherwise are uniform. It is shown that sweeping the blades reduces the thickness and loading noise, but there is no optimum sweep which generates the lowest noise.

Farassat, F.↗
NASA NTRS1977

Comparison of computer codes for calculating dynamic loads in wind turbines

Seven computer codes for analyzing performance and loads in large, horizontal-axis wind turbines were used to calculate blade bending moment loads for two operational conditions of the 100 kW Mod-O wind turbine. Results are compared with test data on the basis of cyclic loads, peak loads, and harmonic contents. Four of the seven codes include rotor-tower interaction and three are limited to rotor analysis. With a few exceptions, all calculated loads were within 25% of nominal test data.

Spera, D. A.↗
NASA NTRS1979

Fluctuating loads measured on an over-the-wing supersonic jet model

Fluctuating pressure loads on the wing and flap of an over-the-wing supersonic jet model were measured. The model was tested statically and at a Mach number of 0.1 in a small free jet to simulate forward speed. Test parameters were impingement angle, nozzle height, and flap deflection. Load levels as high as 170 db were measured at the center of the impingement region during static tests. Forward speed reduced the loading about 1 db. Load level increased with increasing impingement angle and decreasing nozzle height above the wing. The effect of flap deflection was small. When scaled to full-size aircraft conditions, the maximum amplitude of the one-third-octave fluctuating pressure spectra was about 154 db at about 160 Hz. Maximum load level occurred near the intersection of the nozzle center line with the impinged surface. Downstream of the maximum the fluctuating pressure is inversely proportional to the distance downstream of the nozzle.

Willis, C. M.↗
NASA NTRS1979

Design curves for non-linear analysis of simply-supported, uniformly-loaded rectangular plates

Design curves for the non-linear analysis of simply-supported rectangular plates subjected to uniform normal pressure loads have been developed. These curves yield the center deflection, center stress and corner stress in non-dimensionalized form plotted against a dimensionless parameter describing the load intensity. The results presented are based on extensive non-linear finite element analysis employing the ARGUS structural analysis program. Plates with length to width ratios of 1, 1.5, 2, 3 and 4 are included. The load range considered extends to 1000 times the load at which the behavior of the plate becomes significantly non-linear. Over the load range considered, the analysis shows that the ratio of center deflection to plate thickness for a square plate is less than 16 to 1, whereas linear theory would predict a center deflection 400 times the plate thickness. Likewise, the stress is markedly lower than would be predicted by linear theory. The present results are shown to be in excellent agreement with the classical linear theory up to a central deflection to plate thickness ratio of about one-half. In the non-linear regime the present results for deflection and stress are in very good agreement with the analytical and experimental work of other investigators.

Moore, D.↗
NASA NTRS1979

Numerical computation of aeroelastically corrected transonic loads

A numerical scheme is presented for the computation of transonic aerodynamic loads on flexible wings. The method consists of iteratively applying the loads computed by a 3D transonic aerodynamics code to a structural model to obtain elastic twist, and then recomputing the loads. Because this iteration is performed concurrently with the iterations performed in computing the aerodynamics, flexible loads are obtained in roughly the same amount of computing time as required to obtain rigid loads. Applications of this method to a flexible supercritical transonic transport wing are presented and compared with model test data.

Chipman, R.↗
NASA NTRS1979

Design maneuver loads for an airplane with an active control system

This paper discusses the results of utilizing a maneuver load control (MLC) system to provide relief from the loads induced by an increase in wing span on a long range version of the Lockheed L-1011 TriStar. The MLC system deflects the outboard aileron symmetrically, in response to accelerometer signals, to redistribute wing airloads during maneuvers. The process of establishing the MLC system requirements, which involves determining the effects on wing loads of the extended wing span and extended aileron, is discussed. Effects of the MLC system and the extended span on the wing loads for symmetric and asymmetric design maneuvers are reviewed. Flight test results are compared with analytical load predictions. Some potential impacts on design requirements due to finite in-flight availability of the MLC system are illustrated.

Ramsey, H. D.↗
NASA NTRS1979

A flight investigation of performance and loads for a helicopter with NLR-1T main-rotor blade sections

Data on performance and rotor loads for a teetering-rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade-section contour are presented. The test envelope included hover, forward-flight speed sweeps from 35 to 85 m/sec, and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point described vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗
NASA NTRS1980

Expanded study of feasibility of measuring in-flight 747/JT9D loads, performance, clearance, and thermal data

The JT9D jet engine exhibits a TSFC loss of about 1 percent in the initial 50 flight cycles of a new engine. These early losses are caused by seal-wear induced opening of running clearances in the engine gas path. The causes of this seal wear have been identified as flight induced loads which deflect the engine cases and rotors, causing the rotating blades to rub against the seal surfaces, producing permanent clearance changes. The real level of flight loads encountered during airplane acceptance testing and revenue service and the engine's response in the dynamic flight environment were investigated. The feasibility of direct measurement of these flight loads and their effects by concurrent measurement of 747/JT9D propulsion system aerodynamic and inertia loads and the critical engine clearance and performance changes during 747 flight and ground operations was evaluated. A number of technical options were examined in relation to the total estimated program cost to facilitate selection of the most cost effective option. It is concluded that a flight test program meeting the overall objective of determining the levels of aerodynamic and inertia load levels to which the engine is exposed during the initial flight acceptance test and normal flight maneuvers is feasible and desirable. A specific recommended flight test program, based on the evaluation of cost effectiveness, is defined.

Sallee, G. P.↗
NASA NTRS1979

Global Earth Response to Loading by Ocean Tide Models

Mathematical and programming techniques to numerically calculate Earth response to global semidiurnal and diurnal ocean tide models were developed. Global vertical crustal deformations were evaluated for M sub 2, S sub 2, N sub 2, K sub 2, K sub 1, O sub 1, and P sub 1 ocean tide loading, while horizontal deformations were evaluated for the M sub 2 tidal load. Tidal gravity calculations were performed for M sub 2 tidal loads, and strain tensor elements were evaluated for M sub 2 loads. The M sub 2 solution used for the ocean tide included the effects of self-gravitation and crustal loading.

Estes, R. H.↗
NASA NTRS1980

A flight investigation of performance and loads for a helicopter with 10-64C main rotor blade sections

A flight investigation produced data on performance and rotor loads for a teetering rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade section contour. The test envelope included hover, forward flight speeds from 34 to 83 m/sec (65 to 162 knots), and collective fixed maneuvers at about 0.25 tip speed ratio. The data set for each test point describes vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak to peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor. Detailed data for an advanced airfoil on an AH-1G are presented.

Morris, C. E. K.↗
NASA NTRS1979

The role of crack blunting in sustained load crack growth

Sustained load crack growth occurs in metals following critical crack extension above KIc and in aggressive environments while maintaining a constant load below KIc. In this paper, crack arrest measurements are performed on precracked, 0.0254-m thick, side-grooved WOL specimens exposed to 34.5 MN/sq m hydrogen at ambient temperature. The specimens are loaded inside a pressure vessel while in contact with the high pressure hydrogen environment. Crack growth is observed with each loading increment. The crack blunting observed in the fracture mechanics tests on 321 stainless steel is found to be similar to that produced in the 321 stainless steel tensile specimens. Rounding and branching of the crack decreases the effective stress intensity at the crack tip. It is possible, for materials in which cracks tend to blunt or branch in hydrogen, that although cracks will arrest at a relatively high stress intensity in decreasing stress intensity test, a crack may begin to grow at a lower stress intensity when loaded in hydrogen, and the crack may continue to grow when the stress intensity is continually increasing.

Walter, R. J.↗
NASA NTRS1981

Current research on shear buckling and thermal loads with PASCO: Panel Analysis and Sizing Code

The PASCO computer program to obtain the detailed dimensions of optimum stiffened composite structural panels is described. Design requirements in terms of inequality constraints can be placed on buckling loads or vibration frequencies, lamina stresses and strains, and overall panel stiffness for each of many load conditions. General panel cross sections can be treated. An analysis procedure involving a smeared orthotropic solution was investigated. The conservatism in the VIPASA solution and the danger in a smeared orthotropic solution is explored. PASCO's capability to design for thermal loadings is also described. It is emphasized that design studies illustrate the importance of the multiple load condition capability when thermal loads are present.

Stroud, W. J.↗
NASA NTRS1981

A multi-purpose method for analysis of spur gear tooth loading

A large digitized approach was developed for the static and dynamic load analysis of spur gearing. An iterative procedure was used to calculate directly the "variable-variable" gear mesh stiffness as a function of transmitted load, gear tooth profile errors, gear tooth deflections and gear hub torsional deformation, and position of contacting profile points. The developed approach can be used to analyze the loads, Hertz stresses, and PV for the normal and high contrast ratio gearing, presently the modeling is limited to the condition that for a given gear all teeth have identical spacing and profiles (with or without surface imperfections). Certain types of simulated sinusoidal profile errors and pitting can cause interruptions of the gear mesh stiffness function and, thus, increase the dynamic loads in spur gearing. In addition, a finite element stress and mesh subprogram was developed for future introduction into the main program for calculating the gear tooth bending stresses under dynamic loads.

Kasuba, R.↗
NASA NTRS1983

Dynamic tooth loads and stressing for high contact ratio spur gears

An analysis and computer program were developed for calculating the dynamic gear tooth loading and root stressing for high contact ratio gearing (HCRG) as well as LCRG. The analysis includes the effects of the variable tooth stiffness during the mesh, tooth profile modification, and gear errors. The calculation of the tooth root stressing caused by the dynamic gear tooth loads is based on a modified Heywood gear tooth stress analysis, which appears more universally applicable to both LCRG and HCRG. The computer program is presently being expanded to calculate the tooth contact stressing and PV values. Sample application of the gear program to equivalent LCRG (1.566 contact ratio) and HCRG (2.40 contact ratio) revealed the following: (1) the operating conditions and dynamic characteristics of the gear system an affect the gear tooth loading and root stressing, and therefore, life significantly; (2) the length of the profile modification affect the tooth loading and root stressing significantly, the amount depending on the applied load, speed, and contact ratio; and (3) the effect of variable tooth stiffness is small, shifting and increasing the response peaks slightly from those for constant tooth stiffness.

Cornell, R. W.↗
NASA NTRS1983

Structural qualification testing and operational loading on a fiberglass rotor blade for the Mod-OA wind turbine

Fatigue tests were performed on full- and half-scale root end sections, first to qualify the root retention design, and second to induce failure. Test methodology and results are presented. Two operational blades were proof tested to design limit load to ascertain buckling resistance. Measurements of natural frequency, damping ratio, and deflection under load made on the operational blades are documented. The tests showed that all structural design requirements were met or exceeded. Blade loads measured during 3000 hr of field operation were close to those expected. The measured loads validated the loads used in the fatigue tests and gave high confidence in the ability of the blades to achieve design life.

Sullivan, T. L.↗
NASA NTRS1981

Shuttle tile environments and loads

This paper will discuss the Shuttle tile ascent environments and outline the procedures used to convert these environments into tile loads. Testing which was performed to quantify or verify the loads will also be discussed, along with the load combination rationale which was used. The discussion of the ascent environment will be limited to the transonic/supersonic portion of the mission since mechanical design loads occur during this time, and to specific regions of the vehicle, in particular those regions in which undensified critical (black) tiles are located. The induced environments can be broken down into three categories. The first of these are aerodynamic environments. These, in turn, are broken down into two categories-- (I) quasi-steady, which includes spatial surface pressure gradients, pressure differentials due to vent lag, and skin friction, and (2) the unsteady aerodynamics (aero-buffet). The second induced environment is defined as the vibration of the skin-stringer aluminum panels (hereafter referred to as the substrate) due to the acoustic environment. The third environment is defined as a quasi-steady substrate deflection, which results from in-plane and out-of-plane substrate loads.

Ralph J. Muraca↗
NASA NTRS1984

On the use of marker loads and replicas for measuring growth rates for small cracks

The initiation and growth of small cracks (5-500 microns) from edge notches in 2024-T3 aluminum alloy sheets were studied under constant-amplitude loading. Two methods were used to measure crack shape and size. In the first method, striation marker bands were periodically formed along the crack front by interrupting the constant-amplitude loading by either an elevated R-ratio load sequence, or by an overload sequence. In each case the marker loading was selected so as to have minimal influence on the growth rate under the primary loading. In the second method, the surface crack length was monitored by taking surface replicas at regular intervals. The marker band techniques did not provide reliable crack length and crack shape information for cracks smaller than 2 mm. The replica technique provided accurate information for surface crack length at all crack lengths, and fracture tests on specimens with small cracks provided crack-shape information.

Swain, M. H.↗