Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 0.70 to 1.15

A 0.1-scale model of an F-8 aircraft was tested in the Ames 14-Foot Transonic Wind Tunnel at Mach numbers from 0.7 to 1.15. Angle of attack was varied from -2 deg. to 22 deg. at sideslip angles of 0 deg and -5 deg. Reynolds number, dictated by the atmospheric stagnation pressure, varied with Mach number from 3.4 to 4.0 million based on mean aerodynamic chord. The model was configured with a wing designed to simulate the downward deflection of the leading and trailing edges of an advanced-technology-conformal-variable camber wing. This wing was also equipped with conventional (simple hinge) flaps. In addition, the model was tested with the basic F-8 wing to provide a reference for extrapolating to flight data. In general, at all Mach numbers the use of conformal flap deflections at both the leading edge and trailing edge resulted in slightly higher maximum lift coefficients and lower drag coefficients than with the use of simple hinge flaps. There were also found to be small improvements in the pitching-moment characteristics with the use of conformal flaps.

Boltz, F. W.↗
NASA NTRS1978

Flight evaluation of the transonic stability and control characteristics of an airplane incorporating a supercritical wing

A TF-8A airplane was equipped with a transport type supercritical wing and fuselage fairings to evaluate predicted performance improvements for cruise at transonic speeds. A comparison of aerodynamic derivatives extracted from flight and wind tunnel data showed that static longitudinal stability, effective dihedral, and aileron effectiveness, were higher than predicted. The static directional stability derivative was slower than predicted. The airplane's handling qualities were acceptable with the stability augmentation system on. The unaugmented airplane exhibited some adverse lateral directional characteristics that involved low Dutch roll damping and low roll control power at high angles of attack and roll control power that was greater than satisfactory for transport aircraft at cruise conditions. Longitudinally, the aircraft exhibited a mild pitchup tendency. Leading edge vortex generators delayed the onset of flow separation, moving the pitchup point to a higher lift coefficient and reducing its severity.

Matheny, N. W.↗
NASA NTRS1976

Summary of low-speed aerodynamic characteristics of upper-surface-blown jet-flap configurations

The results of recent wind tunnel investigations to provide fundamental information on the upper surface blown (USB) jet flap concept demonstrated that the USB concept provides good high-lift performance. It is shown that the low speed performance is dependent upon the jet turning angle and turning efficiency and on the use of proper leading and trailing edge treatment to prevent premature flow separation. The best means of achieving good turning performance in any particular USB application must be determined from overall operational considerations in which high speed performance, structures and noise, as well as low speed performance, are evaluated. The large diving moments generated at high lift coefficients can be trimmed satisfactorily with a large, conventional horizontal tail; a high tail position is best from longitudinal stability considerations. Large rolling and yawing moments are introduced with the loss of an engine, but these moments can be trimmed satisfactorily through the use of asymmetrical boundary layer control and through the use of spoiler and rudder deflection as needed.

Phelps, A. E., III↗
NASA NTRS1978

Bounds on thickness and loading noise of rotating blades and the favorable effect of blade sweep on noise reduction

The maxima of amplitudes of thickness and loading noise harmonics are established when the radial distribution of blade chord, thickness ratio, and lift coefficient is specified. It is first shown that only airfoils with thickness distribution and chordwise loading distributions which are symmetric with respect to midchord need be considered for finding the absolute maxima of thickness and loading noise. The resulting chordwise thickness and load distributions for these maximum noise conditions require infinite slope at some points along the chord but otherwise are uniform. It is shown that sweeping the blades reduces the thickness and loading noise, but there is no optimum sweep which generates the lowest noise.

Farassat, F.↗
NASA NTRS1978

Theoretical and experimental aerodynamics of strake-wing interactions up to high angles-of-attack

This paper reports on an experimental investigation where the longitudinal aerodynamic characteristics were determined up to high angles-of-attack for configurations employing parametric variations in strake span and wing sweep and includes correlations with theory. The investigation included both component and complete configuration studies to provide information for the analysis of interaction effects. Comparisons between strake-wing and high canard-wing configurations demonstrate the strake-wing to develop higher lift coefficients than did the canard-wing due to enhanced interference effects. Correlations with theory demonstrate the suction analogy to be a useful method for estimating the effects of vortex flow aerodynamics on both component and total forces and moments.

Luckring, J. M.↗
NASA NTRS1978

Effects of inlet airframe integration on the inlet of an upper surface blowing four-engine STOL aircraft

Inlet and nacelle static pressures were measured on a 0.55-scale model of the Quiet Short-Haul Research Airplane (QSRA) in the Ames Research Center's 40- by 80-Foot Wind Tunnel. This model is powered by four JT-15D engines located above the wing with closely spaced adjacent inlets. A fifth JT-15D engine in the fuselage provides boundary-layer control air. Each inlet was instrumented with four to eight rows of axial pressure taps located between X/R approximately plus or minus 1. The tests simulated a broad range of aircraft operating conditions, including engine-out, with lift coefficients from 0.8 to 10.0. Results indicate that the inlets perform well under most operating conditions with little interaction between inlets when the aircraft is moving. Potential problem areas identified are high sideslip angle during approach and an interaction effect between adjacent inlets with high mass flows in static conditions.

Shovlin, M. D.↗
NASA NTRS1978

A new method for designing shock-free transonic configurations

A new method for the design of shock-free supercritical airfoils, wings, and three-dimensional configurations is described. Results illustrating this procedure in two and three dimensions are given. They include modifications to part of the upper surface of an NACA 64A410 airfoil that will maintain shock-free flow over a range of Mach numbers for a fixed lift coefficient, and the modifications required on part of the upper surface of a swept wing with an NACA 64A410 root section to achieve shock-free flow. While the results are given for inviscid flow, the same procedures can be employed iteratively with a boundary layer calculation in order to achieve shock-free viscous designs. With a shock-free pressure field the boundary layer calculation will be reliable and not complicated by the difficulties of shock-wave boundary-layer interaction.

Sobieczky, H.↗
NASA NTRS1978

A method for localizing wing flow separation at stall to alleviate spin entry tendencies

A wing leading-edge modification has been developed, applicable at present to single-engine light aircraft, which produces stabilizing vortices at stall and beyond. These vortices have the effect of fixing the stall pattern of the wing such that the various portions of the wing upper surface stall nearly symmetrically. The lift coefficient produced is essentially constant to very high angles of attack above the stall angle of the unmodified wing. It is hypothesized that these characteristics will help prevent inadvertent spin entry after a stall. Results are presented from recent large-scale wind-tunnel tests of a complete light aircraft, both with and without the modification.

Feistel, T. W.↗
NASA NTRS1978

A new method for designing shock-free transonic configurations

A method for the design of shock free supercritical airfoils, wings, and three dimensional configurations is described. Results illustrating the procedure in two and three dimensions are given. They include modifications to part of the upper surface of an NACA 64A410 airfoil that will maintain shock free flow over a range of Mach numbers for a fixed lift coefficient, and the modifications required on part of the upper surface of a swept wing with an NACA 64A410 root section to achieve shock free flow. While the results are given for inviscid flow, the same procedures can be employed iteratively with a boundary layer calculation in order to achieve shock free viscous designs. With a shock free pressure field the boundary layer calculation will be reliable and not complicated by the difficulties of shock wave boundary layer interaction.

Sobieczky, H.↗
NASA NTRS1978

Evaluation of interference in the OSU 6 in. by 22 in. transonic airfoil tunnel

Interference in a 6 in. by 22 in. two-dimensional wind tunnel was evaluated at Mach numbers up to 1.06 by comparing pressure distributions from airfoil models of differing size. Models of the NACA 0012 profile, having chords of 76, 152, and 305 mm, were used in one phase of the evaluation program, and models of a supercritical profile, having chords of 76 and 152 mm, were used in another. The confinement interference, was documented i.e., blockage, downwash and streamline curvature, all of which are quite small on a model having a chord of 152 mm and which can, for most applications, be ignored. Specifically, the corrections were lumped into an attack angle adjustment of -0.16 degrees per unit lift coefficient on a 152 mm model.

Lee, J. D.↗
NASA NTRS1979

Improved prediction of laminar leading edge separation

Research was conducted to provide a definite criterion for the prediction of the bubble burst on airfoils typical of those used for fighter wings. The approach taken was to correlate existing airfoil bubble burst data using various parameters at the laminar separation point. The method due to Weber was modified to provide a continuous analytic solution for the velocity distribution around the airfoil leading edge. Coupling the modified Weber method with the Stratford laminar separation prediction method leads to a universal chart giving the conditions at separation as a function of stagnation location and leading edge radius. Application of the combined method to available two-dimensional airfoil data resulted in an empirical criterion presenting the limiting local velocity gradient at separation as a function of the boundary layer momentum thickness at separation for bubble burst. The correlation leads as well to the qualitative explanation of two types of laminar stall: thin airfoil and leading edge. The validity of the correlation is demonstrated by predicting the lift coefficient and angle of attack for stall on airfoils with leading edge or trailing edge flaps.

Herring, R. N.↗
NASA NTRS1979

Introduction to the arcopter arc wing and the Bertelsen effect for positive pitch stability and control

A brief report, offered on a wing design, new in geometry, construction, and flight characteristics. Preliminary wind tunnel data on a three-dimensional model was well as some full-scale man-carrying test results are included. There are photos of all phases of the experiments and some figures which serve to illustrate the Bertelsen Effect, a unique focus of aerodynamic forces in the arc wing system which allows the attainment of high lift coefficients with the maintenance of pitch stability and control.

Bertelsen, W. D.↗
NASA NTRS1979

Some new airfoils

A computer approach to the design and analysis of airfoils and some common problems concerning laminar separation bubbles at different lift coefficients are briefly discussed. Examples of application to ultralight airplanes, canards, and sailplanes with flaps are given.

Eppler, R.↗
NASA NTRS1977

Low-speed wind tunnel results for a modified 13-percent-thick airfoil

Wind-tunnel tests were conducted to evaluate the effects on performance of modifying a 13-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the aft upper surface pressure gradient and hence delay boundary layer separation at typical lift coefficients for light general aviation airplanes. The tests were conducted at a Mach number of 0.15 or less over a Reynolds number range from about 1,000,000 to 9,000,000.

Mcghee, R. J.↗
NASA NTRS1979

Low-speed wind-tunnel investigation of wing fins as trailing-vortex-alleviation devices on a transport airplane model

The trailing-vortex-alleviation effectiveness of both a one- and a two-fin configuration (semicircular with a radius of 0.043 semispan) on a jumbo-jet transport airplane model in its landing configuration was investigated in the Langley V/STOL tunnel, by the trailing-wing sensor technique. The fins were located on the upper surface of the transport model wing along the 30-percent-chord line. The fin configurations were effective in reducing the vortex-induced rolling moment, by amounts varying from 28 to 60 percent, on the trailing wing model located at a distance of 7.8 transport model wing spans downstream of the transport model. The flow over the fins and over the transport airplane model wing downstream of the fins was observed to be separated and turbulent. All fin configurations caused a reduction in maximum lift coefficient, a positive increment in drag coefficient, and an increment in nose-up pitching-moment coefficient on the transport airplane model.

Croom, D. R.↗
NASA NTRS1979

Wind-tunnel investigation of highly maneuverable supersonic V/STOL fighter

Results from the initial wind-tunnel test of a large-scale, highly maneuverable supersonic V/STOL fighter model in the Ames 40- by 80-foot wind tunnel are summarized. The STOL configuration which was tested combined upper surface blowing and spanwise blowing to improve the lift characteristics over a wide angle-of-attack range. A close-coupled canard was added to this configuration to create a highly maneuverable STOL aircraft. The 7.28 m (24 ft) span model was powered by two J-97 turbojet engines, each producing 9340 N (2200 lb) thrust at a pressure ratio of 2. With the nozzle flap and aileron set at 30 deg, the model produced lift coefficients greater than 4. The model was longitudinally unstable because of the forward canard position and because of the large body area of fuselage, strake, and nacelles forward of the center of gravity.

Falarski, M. D.↗
NASA NTRS1979

Recent advances in the solution of three-dimensional flow over wings with leading edge vortex separation

Recent advances in a panel method for the solution of three-dimensional flow about wing and wing-body combinations with leading-edge vortex separation are presented. These advances were achieved as part of an ultimately successful assault on two shortcomings of the method, namely convergence failures in seemingly random cases, and overprediction of lift coefficient for high aspect-ratio wings. Advances include the implementation of improved panel numerics for the purpose of eliminating the highly non-linear effects of ring vortices around doublet panel edges, and the development of a least squares procedure for damping vortex sheet geometry update instabilities. A variety of cases generated by the computer program implementing the method are presented. These cases are of two types. The first type consists of numerical studies, which verify the underlying mathematical assumptions of the method and moreover show that the results are strongly invariant with respect to such user dependent input as wing panel layout, initial sheet shape, sheet rollup, etc. The second type consists of cases run for the purpose of comparing computed results with experimental data, and these comparisons verify the underlying physical assumptions made by the method.

Johnson, F. T.↗
NASA NTRS1979

Technology and operational considerations for low-heat-rate trajectories

A broad parametric study which examines several critical aspects of low-heat-rate entry trajectories is performed. Low planform loadings associated with future winged earth-entry vehicles coupled with the potential application of metallic thermal protection systems (TPS) suggest that such trajectories are of particular interest. Studied are three heating conditions - reference, stagnation, and windward centerline, for both laminar and turbulent flow; configuration-related factors including planform loading and hypersonic angle of attack; and mission-related factors such as cross-range and orbit inclination. Results indicate benefits in the design of TPS to be gained by utilizing moderate angles of attack as opposed to high-lift coefficient, high angles of attack, during entry. An assessment of design and technology implications is made.

Wurster, K. E.↗