Search NASA⌕ Search

SEARCH · Search NASA

Results for “PHASE CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Road load simulator tests of the Gould phase 1 functional model silicon controlled rectifier ac motor controller for electric vehicles

The test results for a functional model ac motor controller for electric vehicles and a three-phase induction motor which were dynamically tested on the Lewis Research Center road load simulator are presented. Results show that the controller has the capability to meet the SAE-J227a D cycle test schedule and to accelerate a 1576-kg (3456-lb) simulated vehicle to a cruise speed of 88.5 km/hr (55 mph). Combined motor controller efficiency is 72 percent and the power inverter efficiency alone is 89 percent for the cruise region of the D cycle. Steady state test results for motoring, regeneration, and thermal data obtained by operating the simulator as a conventional dynamometer are in agreement with the contractor's previously reported data. The regeneration test results indicate that a reduction in energy requirements for urban driving cycles is attainable with regenerative braking. Test results and data in this report serve as a data base for further development of ac motor controllers and propulsion systems for electric vehicles. The controller uses state-of-the-art silicon controlled rectifier (SCR) power semiconductors and microprocessor-based logic and control circuitry. The controller was developed by Gould Laboratories under a Lewis contract for the Department of Energy's Electric and Hybrid Vehicle program.

Gourash, F.↗
DOE OSTI2025

Symmetry breaking forms split-off flat bands in quantum oxides controlling metal versus insulator phases

The crystal structure used as input to electronic structure calculation of conventionally bonded solids consists primarily of the standard crystallographic degrees of freedom. Quantum solids sometimes have additional microscopic degrees of freedom (m-DOF) nested within the crystallographic structure. These might include local motifs including positional (Peierls dimers, deformed octahedra, Jahn-Teller distortions), magnetic (local moment configurations) and dipolar (local ferroelectric configurations). Such motifs can be observed experimentally via local probes that avoid averaging, and theoretically as distinct total energy lowering features relative to more simplified “average crystallographic structures”. Here we examine the ability of electronic structure methods independent of strong correlation physics to explain the broad phenomenology of metal-insulator selectivity in quantum oxides by energy-lowering symmetry breaking. We do this by avoiding the restriction of considering only (i) electron-electron interactions in a fixed unresponsive lattice—as done in Mott strong correlation explanations—allowing, however, (ii) local positional and magnetic motifs that coexist within a crystallographic landscape. We find in a broad range of quantum oxides with different symmetry breaking modes the formation of split-off flat bands that can also control metallic versus insulating characteristics. The split-off band effect is common to magnetic and non-magnetic materials, including both binary and ternary oxides. One finds that when such local symmetry breaking motifs are considered in mean-field-like (e.g. density functional theory) electronic structure calculations of quantum oxides, they explain many of the observed trends in metal vs insulator phases discussed otherwise in prior literature via strong correlation in symmetry unbroken view.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1993

Neural self-tuning adaptive control of non-minimum phase system

The motivation of this research came about when a neural network direct adaptive control scheme was applied to control the tip position of a flexible robotic arm. Satisfactory control performance was not attainable due to the inherent non-minimum phase characteristics of the flexible robotic arm tip. Most of the existing neural network control algorithms are based on the direct method and exhibit very high sensitivity, if not unstable, closed-loop behavior. Therefore, a neural self-tuning control (NSTC) algorithm is developed and applied to this problem and showed promising results. Simulation results of the NSTC scheme and the conventional self-tuning (STR) control scheme are used to examine performance factors such as control tracking mean square error, estimation mean square error, transient response, and steady state response.

Ho, Long T.↗
NASA NTRS2011

Adaptive Control of Non-Minimum Phase Modal Systems Using Residual Mode Filters2

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will modify the adaptive controller with a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. This paper will be divided into two parts. Here in Part I we will review the basic adaptive control approach and introduce the primary ideas. In Part II, we will present the RMF methodology and complete the proofs of all our results. Also, we will apply the above theoretical results to a simple flexible structure example to illustrate the behavior with and without the residual mode filter.

Balas, Mark J.↗
DOE OSTI2025

Full complex amplitude control of second-harmonic generation via electrically tunable intersubband polaritonic metasurfaces

Nonlinear intersubband polaritonic metasurfaces based on coupling of the intersubband nonlinear optical response of quantum-engineered semiconductor heterostructures and electromagnetic modes of nanoresonators provide efficient frequency mixing with moderate pump intensities. The resonant nonlinear optical response, represented as a complex function, can be modulated via Stark tuning of intersubband transition energies under applied voltages. However, achieving full complex amplitude control (both phase and magnitude) remains challenging. In this work, we present and experimentally validate electrically tunable nonlinear intersubband polaritonic metasurfaces that achieve complete complex amplitude control for second-harmonic generation (SHG). Through a design featuring two in-plane flipped meta-atoms per unit cell, we achieve complete electrical control of both the amplitude and phase of the metasurface second-order nonlinear susceptibility, with a tuning range of 0 to 30 nm V −1 for the magnitude and 0-2π for the phase of the nonlinear optical response. Using these properties, we achieve complete on-off SHG modulation and beam diffraction tuning through electrically controlled amplitude and phase gratings.

Science & Technology - Other Topics↗
NASA NTRS1972

Space shuttle: High angle of attack transition and low angle of attack launch phase aerodynamic stability and control of GD/C B-18E-2, B-18E-3 delta wing booster, and launch configuration of MSC-040A orbiter and twin pressure fed boosters

The test was a conventional stability and control test except for two aspects. One was the very high angles of attack at which the delta wing configurations were tested (up to 60 degrees) at Mach numbers of 3 and 4.96. The other was the installation of the orbiter and twin boosters in a manner that caused the support system to induce normal forces and side forces on the aft portion of the boosters at all Mach numbers; i.e., the support and the booster bodies were close together, side by side.

Debevoise, J. M.↗
NASA NTRS1983

Digital Single-Phase Power-Factor Controller

Digital circuit has faster response to load changes. Digital power-factor controller senses changing motor-load torques by sampling open-circuit voltage across gate-controlled silicon switch. Circuit responds more rapidly to hanging loads than analog power-factor controllers because no low-pass filter is in feedback loop.

Dabney, R. W.↗
NASA NTRS1983

Space Shuttle flying qualities and flight control system assessment study, phase 2

A program of flying qualities experiments as part of the Orbiter Experiments Program (OEX) is defined. Phase 1, published as CR-170391, reviewed flying qualities criteria and shuttle data. The review of applicable experimental and shuttle data to further define the OEX plan is continued. An unconventional feature of this approach is the use of pilot strategy model identification to relate flight and simulator results. Instrumentation, software, and data analysis techniques for pilot model measurements are examined. The relationship between shuttle characteristics and superaugmented aircraft is established. STS flights 1 through 4 are reviewed from the point of view of flying qualities. A preliminary plan for a coordinated program of inflight and simulator research is presented.

Myers, T. T.↗
NASA NTRS1993

Phase discriminating capacitive array sensor system

A phase discriminating capacitive sensor array system which provides multiple sensor elements which are maintained at a phase and amplitude based on a frequency reference provided by a single frequency stabilized oscillator. Sensor signals provided by the multiple sensor elements are controlled by multiple phase control units, which correspond to the multiple sensor elements, to adjust the sensor signals from the multiple sensor elements based on the frequency reference. The adjustment made to the sensor signals is indicated by output signals which indicate the proximity of the object. The output signals may also indicate the closing speed of the object based on the rate of change of the adjustment made, and the edges of the object based on a sudden decrease in the adjustment made.

Vranish, John M.↗
NASA NTRS2004

Stressed Oxidation Life Prediction for C/SiC Composites

The residual strength and life of C/SiC is dominated by carbon interface and fiber oxidation if seal coat and matrix cracks are open to allow oxygen ingress. Crack opening is determined by the combination of thermal, mechanical and thermal expansion mismatch induced stresses. When cracks are open, life can be predicted by simple oxidation based models with reaction controlled kinetics at low temperature, and by gas phase diffusion controlled kinetics at high temperatures. Key life governing variables in these models include temperature, stress, initial strength, oxygen partial pressure, and total pressure. These models are described in this paper.

Levine, Stanley R.↗
NASA NTRS1995

Dynamic neural networks based on-line identification and control of high performance motor drives

In the automated and high-tech industries of the future, there wil be a need for high performance motor drives both in the low-power range and in the high-power range. To meet very straight demands of tracking and regulation in the two quadrants of operation, advanced control technologies are of a considerable interest and need to be developed. In response a dynamics learning control architecture is developed with simultaneous on-line identification and control. the feature of the proposed approach, to efficiently combine the dual task of system identification (learning) and adaptive control of nonlinear motor drives into a single operation is presented. This approach, therefore, not only adapts to uncertainties of the dynamic parameters of the motor drives but also learns about their inherent nonlinearities. In fact, most of the neural networks based adaptive control approaches in use have an identification phase entirely separate from the control phase. Because these approaches separate the identification and control modes, it is not possible to cope with dynamic changes in a controlled process. Extensive simulation studies have been conducted and good performance was observed. The robustness characteristics of neuro-controllers to perform efficiently in a noisy environment is also demonstrated. With this initial success, the principal investigator believes that the proposed approach with the suggested neural structure can be used successfully for the control of high performance motor drives. Two identification and control topologies based on the model reference adaptive control technique are used in this present analysis. No prior knowledge of load dynamics is assumed in either topology while the second topology also assumes no knowledge of the motor parameters.

Rubaai, Ahmed↗
NASA NTRS1992

A gallium-arsenide digital phase shifter for clock and control signal distribution in high-speed digital systems

The design, implementation, testing, and applications of a gallium-arsenide digital phase shifter and fan-out buffer are described. The integrated circuit provides a method for adjusting the phase of high-speed clock and control signals in digital systems, without the need for pruning cables, multiplexing between cables of different lengths, delay lines, or similar techniques. The phase of signals distributed with the described chip can be dynamically adjusted in eight different steps of approximately 60 ps per step. The IC also serves as a fan-out buffer and provides 12 in-phase outputs. The chip is useful for distributing high-speed clock and control signals in synchronous digital systems, especially if components are distributed over a large physical area or if there is a large number of components.

Fouts, Douglas J.↗
NASA NTRS1981

A method of testing attitude control systems during the development phase

A technique, utilized on the Space Telescope Program, and used for testing satellite attitude pointing and control systems during the engineering and development phases is presented. The technique verifies the hardware models used in design phase computer simulations, verifies the interface between the flight hardware and flight software, and uncovers hardware/software switching or mode logic problems. The testing is accomplished in two phases: a dynamic hardware simulator phase using hardware electronic simulators and an electronic vehicle motion simulator; and a second real hardware phase utilizing engineering model gyros and reaction wheels on an airbearing table. Both phases use an engineering model of the flight computer, flight algorithms and software, and a breadboard data management and computer hardware interface for timing simulations. The purpose of each test and the test phases are described, and examples of closed loop test results for both attitude hold and maneuvering models are given.

Besonis, A.↗