Search NASA⌕ Search

SEARCH · Search NASA

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

MODIS Solar Diffuser Attenuation Screen Modeling Results

On-orbit calibration of the reflected solar bands on the EOS Moderate Resolution Imaging Spectroradiometer (MODIS) is accomplished by have the instrument view a high reflectance diffuse surface illuminated by the sun. For some of the spectral bands this proves to be much too bright a signal that results in the saturation of detectors designed for measuring low reflectance (ocean) surfaces signals. A mechanical attenuation device in the form of a pin hole screen is used to reduce the signals to calibrate these bands. The sensor response to solar illumination of the SD with and without the attenuation screen in place will be presented. The MODIS detector response to the solar diffuser is smooth when the attenuation screen is absent, but has structures up to a few percent when the attenuation screen is present. This structure corresponds to non-uniform illumination from the solar diffuser. Each pin hole produces a pin-hole image of the sun on the solar diffuser, and there are very many pin hole images of the sun on the solar diffuser for each MODIS detector. Even though there are very many pin-hole images of the sun on the solar diffuser, it is no longer perfectly uniformly illuminated. This non-uniformly illuminated solar diffuser produces intensity variation on the focal planes. The results of a very detailed simulation will be discussed which show how the illumination of the focal plane changes as a result of the attenuation, and the impacts on the calibration will be discussed.

Waluschka, Eugene↗
NASA NTRS2006

Bearing-Load Modeling and Analysis Study for Mechanically Connected Structures

Bearing-load response for a pin-loaded hole is studied within the context of two-dimensional finite element analyses. Pin-loaded-hole configurations are representative of mechanically connected structures, such as a stiffener fastened to a rib of an isogrid panel, that are idealized as part of a larger structural component. Within this context, the larger structural component may be idealized as a two-dimensional shell finite element model to identify load paths and high stress regions. Finite element modeling and analysis aspects of a pin-loaded hole are considered in the present paper including the use of linear and nonlinear springs to simulate the pin-bearing contact condition. Simulating pin-connected structures within a two-dimensional finite element analysis model using nonlinear spring or gap elements provides an effective way for accurate prediction of the local effective stress state and peak forces.

Knight, Norman F., Jr.↗
NASA NTRS1989

Toggle release

A pyrotechnic actuated structural release device 10 which is mechanically two fault tolerant for release. The device 10 comprises a fastener plate 11 and fastener body 12, each attachable to a different one of a pair of structures to be joined. The fastener plate 11 and body 12 are fastenable by a toggle 13 supported at one end on the fastener plate and mounted for universal pivotal movement thereon. At its other end which is received in a central opening in the fastener body 12 and adapted for limited pivotal movement therein the toggle 13 is restrained by three retractable latching pins 61 symmetrically disposed in equiangular spacing about the axis of the toggle 13 and positionable in latching engagement with an end fitting on the toggle. Each pin 61 is individually retractable by combustion of a pyrotechnic charge 77, the expanding gases of which are applied to a pressure receiving face 67 on the latch pin 61 to effect its retraction from the toggle. While retraction of all three pins 62 releases the toggle, the fastener is mechanically two fault tolerant since the failure of any single one or pair of the latch pins to retract results in an asymmetrical loading on the toggle and its pivotal movement to effect a release. An annular bolt 18 is mounted on the fastener plate 11 as a support for the socket mounting 30, 37 of the toggle whereby its selective axial movement provides a means for preloading the toggle.

Graves, Thomas J.↗
NASA NTRS2011

Cup waveguide antenna with integrated polarizer and OMT

A cup waveguide antenna with integrated polarizer and OMT for simultaneously communicating left and right hand circularly polarized electromagnetic waves is adjustable to obtain efficient propagation and reception of electromagnetic waves. The antenna includes a circular waveguide having an orthomode transducer utilizing first and second pins longitudinally spaced apart and oriented orthogonally with respect to each other. Six radially-oriented adjustable polarizer screws extend from the exterior to the interior of the waveguide. A septum intermediate the first and second pins is aligned with the first pin. Adjustment of the polarizer screws enables maximized propagation of and/or response to left hand circularly polarized electromagnetic waves by the first pin while simultaneously enabling maximized propagation of and/or response to right hand circularly polarized electromagnetic waves by the second pin.

Acosta, Roberto J.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-12137-DND

Future robotic missions to Mars and, eventually, human missions to Mars will require landing massive spacecraft with ?pin point? accuracy, e.g., the planned Mars Sample Return (MSR) mission will require ?pin point? landing accuracy to rendezvous with the previously cached Mars samples to be re-turned to Earth and the first human mission to Mars, with payloads estimated to be in excess of 40 metric tons, must land very close to the cargo spacecraft that precede it on the journey to Mars. Hence, ?pin point? entry, descent and landing (EDL) has become a major technological driver in future massive robot-ic and human mission to Mars [1]. To achieve ?pin point? EDL on Mars, we must predict the atmospheric density, atmospheric winds and atmospheric dust level to an accuracy previously unobtainable. To develop an accurate and precise predictive model of the atmosphere of Mars, we propose a Mars-orbiting LIDAR system to measure/monitor the density, winds and dust in the atmosphere of Mars over two Mars years. The LIDAR measurements will be used to develop an accurate model of the atmosphere of Mars to be used for ?pin point? EDL for future Mars missions.

U. N. Singh↗
NASA NTRS2021

Deriving Deformable Mirror Performance Requirements in Simulation with Experimental Verification

Coronagraph instruments rely on predictable and stable deformable mirror (DM) surface displacement to achieve the contrast required to detect Earth-sized exoplanets orbiting nearby Solar-type stars. Anomalous DM behavior, such as unstable or pinned actuators, can limit contrast in coronagraphs. Simulating how these undesired behaviors affect the performance of a high contrast imaging architecture is important for developing requirements on their associated hardware. Simulating a vortex coronagraph (VC) with two deformable mirrors, this study quantifies how the number of pinned actuators affect the performance of Focal Plane Wavefront Sensing and Control algorithms using both Grid Search Electric Field Conjugation (EFC) and Planned EFC, which uses Beta-Bumping. The simulation also quantifies how various types of voltage noise such as zero-mean Gaussian noise, zero-mean periodic noise, and drift can affect the contrast of a VC during an observation run. A tolerance of a change in the Mean Normalized Intensity of ${1\times10^{-11}}$ is allocated to both types of error. If Planned EFC is used, only 1 pinned actuator on both DMs can be tolerated. If only pure Grid Search EFC is used the DMs cannot have any pinned actuators. For the case of zero-mean Gaussian noise and zero-mean periodic noise, one can tolerate a noise standard deviation of no more than ${\sigma = 0.45 \text{ mV}}$. For drift, we can only tolerate ${\sigma = 0.30 \text{ mV}}$ or less. These results show that the DM electronics and the DM themselves need to be nearly defect free to avoid having more than 1 pinned actuator. The electronics need to be tested for different types of noise statistics and that both the average and standard deviation of the noise should be measured.

Dean L. Palmer↗
DOE OSTI2020

Self-aligning swaging punch and method for swaging

A self-aligning swaging punch is provided for adjoining together a pin and a workpiece having a pinhole. The swaging punch comprises a shaft and a tip having an open-ended cavity. The shaft transfers an axial force from a press or hammer to the tip. The tip transfers the axial force from the shaft to a top surface of the workpiece near the pinhole. The tip may be spherical in shape for evenly deforming the workpiece near the upper edge of the pinhole. The open-ended cavity receives the pin therein and allows the pin to extend at least partially into the open-ended cavity while the tip contacts the workpiece. The open-ended cavity also ensures that the swaging punch is aligned with the pinhole and perpendicular to the surface of the workpiece when the pin is inserted into the pinhole such that the workpiece evenly deforms and presses against the pin.

42 ENGINEERING↗
DOE OSTI2025

Recent Metallic Fuel Data Recovery in FIPD

The Metallic Fuels Irradiation and Physics Database (FIPD) [1] is an organized collection of metallic fuel test pin data (U-xPu-yZr, = 0 ~ 28; y = 2 ~ 10) and documentation available to industry. FIPD mainly contains three types of data: (1) Fuel pin fabrication data, including fuel slug diameter, fuel slug length, cladding diameter, smear density, etc. (2) Fuel pin operation conditions, including axial distributions for power, temperatures, fluences, burnup, and isotopic densities, etc. and (3) Fuel pin post-irradiation examination (PIE) data, including fission gas release and gas chemistry, profilometry, and neutron radiography, etc. The operating conditions for pins with PIE data available in FIPD span significant ranges across key parameters. The fuel peak burnup extends from less than 5% up to 20 at%. The cladding peak temperature varies from about 490°C to 660°C. Finally, the cladding peak DPA shows a wide range from less than 5 to 120. These broad ranges reflect the diverse testing conditions and operational parameters captured in the available PIE data. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). As reported in the ref. [3, 4], most of the PIE data generated during the IFR program [5] has been collected, reviewed, processed, and integrated into FIPD. The most recently added PIE data can be found in ref. [4], which shows the collection of over 95% of the PIE data by the time of this paper. The recent improvements to the database are summarized in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Non-destructive Post-Transient Examination Results of the MOXTOP-1 Experiment

The MOXTOP-1 experiment has been assembled and irradiated in INL’s HFEF and TREAT facilities followed by disassembly of the experiment to enable initial post-transient examination. Results of neutron radiography of the fuel pin still in the THOR capsule were somewhat inconclusive due to the additional scatter and attenuation from the iron heat sink included in the design. Nonetheless, no obvious failure or fuel relocation could be identified in the radiography. Following disassembly of the fuel pin from the capsule, initial visual inspections were performed, and documented via images obtained through the hot cell window. No obvious signs of fuel failure were identified, indicating that the fuel pin remained intact during the transient. Some discoloration was observed near the middle of the fuel pin, likely corresponding to the fueled zone indicating that that region may have reached a relatively high temperature. Pre-transient, and post-transient profilometry of the fuel pin were performed and compared. Some additional strain displacement in the bottom portion of the fuel zone is identified, but remains well below 1%.

Mixed Oxide↗
DOE OSTI2022

Coupled effect of Cr and Al on interactions between a prismatic interstitial dislocation loop and an edge dislocation line in Fe-Cr-Al alloy

Segregation of alloying elements to a prismatic dislocation loop under irradiation is an important phenomenon in understanding the role of loops in radiation effects in alloys. In this work, various segregation sequences of Cr and Al atoms to a $\langle$100$\rangle$ and a 1/2 $\langle$111$\rangle$ prismatic dislocation loop in a Fe-Cr-Al alloy are explored using molecular dynamics method and ab initio energy calculation. Here, the results reveal that Cr can readily segregate to the loops while Al atoms cannot by themselves, but the segregated Cr atoms are able to promote Al segregation at the loops, defined as a coupled segregation of Cr and Al. After interacting with Cr and Al, a previously mobile 1/2 $\langle$111$\rangle$ loop becomes sessile. Al segregation through the coupled segregation process can further affect the pinning behavior of a dislocation loop to an edge dislocation motion. By varying the Al fraction in the segregated solutes, a nonlinear dependence of the pinning effect on dislocation motion is determined. At lower fractions, the pinning strength increases with the increasing Al fraction until Al fraction reaches a critical value of about 19%, above which the pinning strength decreases with further increase of Al fraction. All these results suggest that, in addition to the effect of Al on the surface resistance to oxidation, Al effect on the dislocation loop behavior is important to optimize the composition of Fe-Cr-Al alloys for their applications in accident tolerant fuel concepts.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Single-Phase Jet Impingement Cooling for a Power-Dense Silicon Carbide Power Module

The adoption of silicon carbide (SiC) devices in the electric vehicle (EV) industry is increasing due to their superior performance over silicon devices. SiC devices enable further miniaturization of EV inverters, increasing their power density, which results in thermal management challenges. Here in this paper, the limits of single-phase jet impingement cooling are explored for an automotive SiC power module. We propose embedding pin fins in the direct-bonded-copper (DBC) substrate of the power module package using laser powder bed fusion additive manufacturing. The thermalhydraulic performance of the DBC-embedded pin fins is compared against folded fins that are directly soldered to the DBC substrate. A heat conduction analysis was conducted on a SiC package to determine the target heat transfer coefficient (HTC) for the heat sink. A water-ethylene glycol (WEG) jet impingement on the proposed concepts was studied using unit-cell models to achieve the target HTC. The studied designs put emphasis on the reliability and manufacturability requirements of the automotive industry. The thermal performance of DBC-embedded pin fins outperformed the DBC-soldered folded fins. The performance of the DBC-embedded pin fins is benchmarked against WEG-based cooling systems of commercial EVs. With the proposed cooling solution, we have shown a pathway of reducing the specific thermal resistance by 75% compared to BMW i3 thermal management system without any penalty on pressure drop or parasitic power.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

30 years of semiconductor nanowire research: A Personal Journey

This project is about flux line pinning in high T c superconductors using columnar defects as the pinning centers. The basic idea is that linear structural defects can pin the flux lines within HTSCs so that their critical current density (the maximal current density that these HTSCs can carry with zero resistance) can be enhanced. The question is how to create such linear structural defects within crystalline cuprate thin films. Scientists have already successfully demonstrated the concept by irradiating HTSC crystals with high-energy ions at synchrotron beamline facilities. However, such heavy ion irradiation is practically not viable for large-scale processes. Finally, we reasoned that maybe we could introduce some sort of linear nanoscopic objects into HTSC to form a composite, and then these linear nanoscopic objects would serve as the magnetic flux line pinning centers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Modeling discontinuous dynamic recrystallization containing second phase particles in magnesium alloys utilizing phase field method

Pre-existing second phase particles can induce particle stimulated nucleation (PSN) and pinning effect on grain boundaries during DRX process of magnesium alloys. The interaction among pinning effect, PSN mechanism and strain-induced grain boundary migration (SIBM) nucleation mechanism imposes challenge in quantitative study of microstructure evolution. A phase field model that describes discontinuous dynamic recrystallization process considering second phase particles (PF-DDRX-SP) which mainly distribute along grain boundaries is developed. The second phase order parameter with diffusion interface is introduced to the free energy function. With considering the pinning effect of second phase particles on grain boundaries, the grain boundary energy couples the interaction between second phase and grains. The effect of second phase on dislocation density evolution is considered in the model, and the PSN and SIBM mechanism are both executed by limiting the nucleation position to the grain boundary and the second phase interface. For the validation, the initial topology consistent with initial microstructure is applied to the simulation of DRX kinetics and flow behavior of AZ80 magnesium alloy, and great reliability and accuracy of developed model is indicated. Furthermore, through the model, the microstructure evolution with different particle size and with different volume fraction of round particle during DRX process were simulated. Finally, the results show that particles with higher dispersion reduce the number of DRX nuclei, which indicate that second phase particles suppress the nucleation at grain boundaries because of the pinning effect. More importantly, the proposed model could also quantitatively predict the relationships between the parameters of second phase particles and DRX behaviors, and enable to optimize the initial second phase structure in a uniform grain structure during thermomechanical process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design optimization of an additively manufactured prototype recuperator for supercritical CO 2 power cycles

Supercritical CO 2 (sCO 2 ) power cycles are being developed due to their potential for high efficiency and reduced capital cost. It is necessary that these recuperators operate at high pressures and temperatures, up to 30 MPa and 900 K, with effectiveness values > 95% and pressure drops <1% to achieve high cycle efficiencies. Moreover, it is also necessary to have reasonable cost recuperators to control the capital costs of the sCO 2 power cycles. In this study, a Plate Pin-Fin (PPF) heat exchanger has been proposed as an sCO 2 recuperator. This preliminary recuperator design leverages capabilities enabled by additive manufacturing. Although the PPF design has characteristics similar to those of a plate heat exchanger, small diameter and relatively long fins are used to increase surface area, enhance heat transfer, and provide structural support for the partition plates that separate the fluid streams. Existing correlations for heat transfer and pressure drop were adapted for the PPF heat exchanger. These correlations were implemented in a 1D analytical model and used for the optimization of a 5-kW th high temperature recuperator for an indirect sCO 2 cycle by varying the design parameters to minimize the quantity of material required. A 3D conjugate heat transfer numerical simulations were conducted to validate the heat transfer and pressure loss correlations. A steepest descent method was used to minimize heat exchanger mass for a 5-kW prototype recuperator subject to a maximum specified pressure drop. Additionally, the design analysis indicated that an optimum PPF recuperator would be attained for the minimum allowable pin transverse spacing, minimum pin width, minimum pin height and near maximum cell aspect ratio. Moreover, at a low material requirement of 0.216 kg/kW and a pressure drop, which is almost five times lower than the allowable pressure drop design target, the optimized PPF heat exchanger has the high potential to be an alternative to a printed circuit heat exchanger, which is a conservative design basis for the current state-of-the-art sCO 2 recuperators.

42 ENGINEERING↗
DOE OSTI2023

Jacobian-free Newton–Krylov method for the simulation of non-thermal plasma discharges with high-order time integration and physics-based preconditioning

A preconditioning framework for the numerical simulation of non-thermal streamer discharges is developed using the Jacobian-free Newton-Krylov (JFNK) method. A reduced plasma fluid model is considered, consisting of electrons, one positive ion, one negative ion, and the electrostatic potential. Here, the plasma kinetics model includes ionization, electron-ion recombination, electron attachment, electron detachment, and ion-ion recombination. The governing equations are made dimensionless, discretized in space with finite differences, and integrated in time with a fully implicit method based on high-order backward differentiation formulas. The preconditioning framework is based on a linearized form of the governing equations and physics-based operator splitting. The efficiency of the preconditioning strategy is assessed through two test cases: streamer propagation between parallel plates and an axisymmetric pin-to-pin discharge. The fully implicit approach overcomes traditional restrictions in the time step size due to processes such as electron drift, electron diffusion, and dielectric relaxation. Excellent performance is observed through relevant statistics of the JFNK solver, although the number of linear iterations increases for the pin-to-pin discharge when nonlinear numerical boundary conditions are imposed at the electrodes. Performance studies show scalability with O(100-1000) processors for O(10M) unknowns with ample room for optimization.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

$\mathrm{REX}$: An analytical tool for reactor operating envelope expansion through fuel-clad thermo-mechanics

Here REX, an analytical reactor design tool for the identification and expansion of reactor operating envelopes, is introduced and detailed. Written in MATLAB, REX takes core geometries and axially discretized detector and depletion output from the Serpent neutron transport code and performs full-core, pin-specific thermal-hydraulic and thermo-mechanical calculations. REX identifies the operating envelopes of advanced, solid-fuel nuclear reactors on the basis of their fuel-cladding, fuel-gas, and coolant-cladding interfacial thermo-mechanics. It iteratively pushes coolant inlet temperatures and modifies fuel pin geometries to induce mechanical failure in their original cladding materials at the fullest extent of their fuel cycle lengths and permissible coolant inlet temperatures. It then attempts to expand their operating envelopes by determining the mechanical responses of alternative cladding materials under the same geometric conditions. The result of the REX calculation sequence is a set of 5-D variables describing the temperatures, pressures, geometries, and mechanics of the core as functions of assembly, fuel pin, axial zone, depletion step, and coolant inlet temperature for each candidate cladding material with the limiting fuel pin geometry for the original material.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

BISON fuel performance modeling optimization for experiment X447 and X447A using axial swelling and cladding strain measurements

With the recent need to qualify new reactor designs such as the Versatile Test Reactor (VTR), fuel performance calculations need to be performed to determine safety criteria of the proposed designs. In order to validate the fuel performance results obtained by a fuel performance code, BISON, for new reactor designs, legacy fuel from EBR-II and FFTF MFF with Post -Irradiation Examination (PIE) data need to be used as validation cases to benchmark models. Here in this work, BISON has been paired with the Fuels Irradiation & Physics Database (FIPD) and IFR Materials Information System (IMIS) to supply PIE data for comparison with simulations of EBR-II experiments X447/X447A. X447/X447A were assessed by implementing models for Fuel Cladding Chemical Interaction (FCCI) within BISON and optimizing the friction coefficient between the fuel surface and the cladding, the anisotropic swelling factor, and the HT9 first thermal creep scalar (which scales the first term in the HT9 creep equation) to best match the PIE axial fuel swelling height and cladding profilometry for all pins in X447/X447A. The optimal values were found using a generic algorithm developed to select different values for the three parameters until end criteria was met and error couldn’t be reduced further. The BISON-simulated cladding profilometry was evaluated using Standard Error of the Estimate (SEE) to account for the profile shape of the cladding profilometry. Optimal values for the friction coefficient, anisotropic fuel swelling factor, and HT9 first thermal creep scalar were found to best fit the BISON simulation results to the PIE measurements found in IMIS and FIPD. Improvements to current models are suggested to account for the underprediction of fuel swelling at low burnups and the overprediction of fuel swelling at higher burnups observed for the axial fuel swelling height. Although two pins in EBR-II X447/X447A (DP70 and DP75) were known to fail due to FCCI, none of the pins simulated in BISON reached a cumulative damage fraction (CDF) above 0.008 with FCCI correlations coupled in the BISON simulations. The error estimate generated for all pins in X447/X447A using optimal values was 209 µm, which is deemed acceptable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Numerical implementation of the MOOSE subchannel module (SCM) algorithm

The subchannel module of moose (SCM), previously referred to as Pronghorn-SC, is a subchannel code designed to resolve single-phase flow fields and calculate the relevant flow variables, in nuclear reactor fuel-pin assemblies. The assemblies it models are: water-cooled, with bare fuel-pins in a square ducted, quadrilateral lattice and liquid-metal/water-cooled, with bare/wire-wrapped fuel pins in a hexagonal ducted, triangular lattice. Previous publications have presented the development, validation and verification of SCM. This work presents an comparative overview of the different solvers implemented within SCM. This includes the solver algorithm description, and a performance comparison. The two test cases chosen to demonstrate the solver performance were taken from the PSBT enthalpy mixing benchmark and the ORNL-19 pin benchmark.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗