Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE DISTRIBUTION - AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Wing-Nacelle-Propeller Interference for Wings of Various Spans Force and Pressure-Distribution Tests

Report presents the results of an experimental investigation made in the NACA full-scale wind tunnel to determine the effect of wing span on nacelle-propeller characteristics and, reciprocally, the lateral extent of nacelle and propeller influence on a monoplane wing. The results provide a check on the validity of the previous research on nacelles and propellers with 15-foot-span wings tested in the 20-foot wind tunnel and reported in technical reports 415, 462, 505, 506, and 507.

Robinson, Russell G↗
NASA NTRS1959

Comparison of Measured Flapwise Structural Bending Moments on a Teetering Rotor Blade With Results Calculated From the Measured Pressure Distribution

Flapwise bending moments were calculated for a teetering rotor blade using a reasonably rapid theoretical method in which airloads obtained from wind-tunnel tests were employed. The calculated moments agreed reasonably well with those measured with strain gages under the same test conditions. The range of the tests included one hovering and two forward-flight conditions. The rotor speed for the test was very near blade resonance, and difficult-to-calculate resonance effects apparently were responsible for the largest differences between the calculated and measured harmonic components of blade bending moments. These differences, moreover, were largely nullified when the harmonic components were combined to give a comparison of the calculated and measured blade total- moment time histories. The degree of agreement shown is therefore considered adequate to warrant the use of the theoretical method in establishing and applying methods of prediction of rotor-blade fatigue loads. At the same time, the validity of the experimental methods of obtaining both airload and blade stress measurement is also indicated to be adequate for use in establishing improved methods for prediction of rotor-blade fatigue loads during the design stage. The blade stiffnesses and natural frequencies were measured and found to be in close agreement with calculated values; however, for a condition of blade resonance the use of the experimental stiffness values resulted in better agreement between calculated and measured blade stresses.

Mayo, Alton P.↗
NASA NTRS1943

Piston Ring Pressure Distribution

The discovery and introduction of the internal combustion engine has resulted in a very rapid development in machines utilizing the action of a piston. Design has been limited by the internal components of the engine, which has been subjected to ever increasing thermal and mechanical stresses, Of these internal engine components, the piston and piston rings are of particular importance and the momentary position of engine development is not seldom dependent upon the development of both of the components, The piston ring is a well-known component and has been used in its present shape in the steam engine of the last century, Corresponding to its importance, the piston ring has been a rich field for creative activity and it is noteworthy that in spite of this the ring has maintained its shape through the many years. From the many and complicated designs which have been suggested as a packing between piston and cylinder wall hardly one suggestion has remained which does not resemble the original design of cast iron rectangular ring.

Kuhn, M.↗
NASA NTRS1987

High-speed code validation

The topics are presented in viewgraph form and include the following: NFL body experiment; high-speed validation problems; 3-D Euler/Navier-Stokes inlet code; two-strut inlet configuration; pressure contours in two longitudinal planes; sidewall pressure distribution; pressure distribution on strut inner surface; inlet/forebody tests in 60 inch helium tunnel; pressure distributions on elliptical missile; code validations; small scale test apparatus; CARS nonintrusive measurements; optimized cone-derived waverider study; etc.

Barnwell, Richard W.↗
NASA NTRS1978

A computer program to calculate the longitudinal aerodynamic characteristics of upper-surface-blown wing-flap configurations

A user's manual is presented for a computer program in which a vortex-lattice lifting-surface method is used to model the wing and multiple flaps. The engine wake model consists of a series of closely spaced vortex rings with rectangular cross sections. The jet wake is positioned such that the lower boundary of the jet is tangent to the wing and flap upper surfaces. The two potential flow models are used to calculate the wing-flap loading distribution including the influence of the wakes from up to two engines on the semispan. The method is limited to the condition where the flow and geometry of the configurations are symmetric about the vertical plane containing the wing root chord. The results include total configuration forces and moments, individual lifting-surface load distributions, pressure distributions, flap hinge moments, and flow field calculation at arbitrary field points. The use of the program, preparation of input, the output, program listing, and sample cases are described.

Mendenhall, M. R.↗
NASA NTRS1988

Improved Zirconia Oxygen-Separation Cell

Cell structure distributes feed gas more evenly for more efficent oxygen production. Multilayer cell structure containing passages, channels, tubes, and pores help distribute pressure evenly over zirconia electrolytic membrane. Resulting more uniform pressure distribution expected to improve efficiency of oxygen production.

Walsh, John V.↗
NASA NTRS1947

Investigation of the Loads on a Conventional Front and Rear Sliding Canopy

As one phase of a comprehensive canopy load investigation, conventional front and rear sliding canopies which are typified by installation on the SB2C-4E airplane, were tested in the Langley full-scale tunnel to determine the pressure distributions and the aerodynamic loads on the canopies. A preliminary analysis of the results of these tests is presented in this report. Plots are presented that show the distribution of pressure at four longitudinal stations through each canopy for a range of conditions selected to determine the effects of varying canopy position, yaw, lift coefficient, and power. The results indicate that the maximum loads, based on the external-internal pressure differential, for the front and rear canopies were obtained with the airplane simulating the high speed flight condition. The highest loading on the front canopy was in the exploding direction for the configuration with the front and rear canopies closed. The highest loads on the rear canopy were in the crushing direction with the front canopy open and the rear canopy closed. For most of the simulated flight conditions, the highest loads on the front canopy, per unit area, were over twice as great as the highest loads on the rear canopy when the comparison was made for the most critical canopy configuration in each case. The external pressure distribution over the front and rear canopies, which were fairly symmetrical to 0 degree angle of yaw, were greatly distorted at other yaw attitudes, particularly for the propeller operating conditions. These distorted pressure distributions resulted in local exploding and crushing loads on both canopies which were often considerably higher than the average canopy loads.

Dexter, Howard E.↗
NASA NTRS1987

Force and moment rotordynamic coefficients for pump-impeller shroud surfaces

Governing equations of motion are derived for a bulk-flow model of the leakage path between an impeller shroud and a pump housing. The governing equations consist of a path-momentum, a circumferential - momentum, and a continuity equation. The fluid annulus between the impeller shroud and pump housing is assumed to be circumferentially symmetric when the impeller is centered; i.e., the clearance can vary along the pump axis but does not vary in the circumferential direction. A perturbation expansion of the governing equations in the eccentricity ratio yields a set of zeroth and first-order governing equations. The zeroth-order equations define the leaking rate and the circumferential and path velocity distributions and pressure distributions for a centered impeller position. The first-order equations define the perturbations in the velocity and pressure distributions due to either a radial-displacement perturbation or a tilt perturbation of the impeller. Integration of the perturbed pressure and shear-stress distribution acting on the rotor yields the reaction forces and moments acting on the impeller face.

Childs, Dara W.↗
NASA NTRS1985

Effects of non-uniform velocity profiles on dual jets in a crossflow

The interaction between engine exhaust jets and the freestream affects the aerodynamic and stability characteristics of VTOL aircraft during the transition from hover to forward flight. This interaction is often modeled as a simple uniform jet issuing from a flat plate into a subsonic crossflow. The distribution of pressures induced by the jet on the surface of the plate can be used to predict the lift loss and pitching moment for a full-scale aircraft. The uniform jet model has limitations because an actual turbofan engine generates a rather nonuniform exit velocity profile. The purpose of this work is to study the effect of a nonuniform velocity profile on the surface pressure distribution. The mutual interaction of dual jets also is investigated in side-by-side and tandem configurations. Detailed pressure distributions are presented for two jet-to-freestream velocity ratios of 2.2 and 4.0. One important finding is that a nonuniform jet with a high velocity periphery and a low velocity core has a higher effective velocity ratio than a uniform jet with the same mass flow.

Moore, C. L.↗
NASA NTRS1960

Distribution of Time-Averaged Pressure Fluctuations Along the Boundary of a Round Subsonic Jet

A semiempirical analysis of the equation for incompressible fluctuations in a turbulent fluid, using similarity relations for round subsonic jets with uniform exit velocity, is used to predict the shape of the time-averaged fluctuation-pressure distribution along the mean-velocity boundary of jets. The predicted distribution is independent of distance downstream of the nozzle exit along the mixing region, inversely proportional to the distance downstream along the region of mean-velocity self-preservation, and proportional to the inverse square of the distance downstream along the fully developed region. Experimental results were in fair agreement with the theory. However, the measured fluctuation-pressure distributions were found to be very sensitive to changes in jet temperature and jet-nozzle profile, especially near the nozzle. These factors are not included in the theory. Increased jet temperatures produce increased pressure fluctuations and violation of similarity conditions. Nozzle-profile modifications may lead to violation of the uniform-exit-velocity requirement imposed in the theory.

Howes, Walton L.↗
NASA NTRS1997

Computational Fluid Dynamics Analysis Method Developed for Rocket-Based Combined Cycle Engine Inlet

Renewed interest in hypersonic propulsion systems has led to research programs investigating combined cycle engines that are designed to operate efficiently across the flight regime. The Rocket-Based Combined Cycle Engine is a propulsion system under development at the NASA Lewis Research Center. This engine integrates a high specific impulse, low thrust-to-weight, airbreathing engine with a low-impulse, high thrust-to-weight rocket. From takeoff to Mach 2.5, the engine operates as an air-augmented rocket. At Mach 2.5, the engine becomes a dual-mode ramjet; and beyond Mach 8, the rocket is turned back on. One Rocket-Based Combined Cycle Engine variation known as the "Strut-Jet" concept is being investigated jointly by NASA Lewis, the U.S. Air Force, Gencorp Aerojet, General Applied Science Labs (GASL), and Lockheed Martin Corporation. Work thus far has included wind tunnel experiments and computational fluid dynamics (CFD) investigations with the NPARC code. The CFD method was initiated by modeling the geometry of the Strut-Jet with the GRIDGEN structured grid generator. Grids representing a subscale inlet model and the full-scale demonstrator geometry were constructed. These grids modeled one-half of the symmetric inlet flow path, including the precompression plate, diverter, center duct, side duct, and combustor. After the grid generation, full Navier-Stokes flow simulations were conducted with the NPARC Navier-Stokes code. The Chien low-Reynolds-number k-e turbulence model was employed to simulate the high-speed turbulent flow. Finally, the CFD solutions were postprocessed with a Fortran code. This code provided wall static pressure distributions, pitot pressure distributions, mass flow rates, and internal drag. These results were compared with experimental data from a subscale inlet test for code validation; then they were used to help evaluate the demonstrator engine net thrust.

Source record↗
NASA NTRS1983

Assessment of NASA and RAE viscous-inviscid interaction methods for predicting transonic flow over nozzle afterbodies

The Langley Research Center of the National Aeronautics and Space Administration and the Royal Aircraft Establishment have undertaken a cooperative program to conduct an assessment of their patched viscous-inviscid interaction methods for predicting the transonic flow over nozzle afterbodies. The assessment was made by comparing the predictions of the two methods with experimental pressure distributions and boattail pressure drag for several convergent circular-arc nozzle configurations. Comparisons of the predictions of the two methods with the experimental data showed that both methods provided good predictions of the flow characteristics of nozzles with attached boundary layer flow. The RAE method also provided reasonable predictions of the pressure distributions and drag for the nozzles investigated that had separated boundary layers. The NASA method provided good predictions of the pressure distribution on separated flow nozzles that had relatively thin boundary layers. However, the NASA method was in poor agreement with experiment for separated nozzles with thick boundary layers due primarily to deficiencies in the method used to predict the separation location.

Putnam, L. E.↗