Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Drastic enhancement of magnetic critical temperature and amorphization in topological magnet EuSn 2 P 2 under pressure

High pressure is an effective tool to induce exotic quantum phenomena in magnetic topological insulators by controlling the interplay of magnetic order and topological state. This work presents a comprehensive high-pressure study of the crystal structure and magnetic ground state up to 62 GPa in an intrinsic topological magnet EuSn 2 P 2 . With a combination of high resolution X-ray diffraction, 151 Eu synchrotron Mössbauer spectroscopy, X-ray absorption spectroscopy, molecular orbital calculations, and electronic band structure calculations, it has been revealed that pressure drives EuSn 2 P 2 from a rhombohedral crystal to an amorphous phase at 36 GPa accompanied by a fourfold enhancement of magnetic ordering temperature. In the pressure-induced amorphous phase, Eu ions take an intermediate valence state. The drastic enhancement of magnetic ordering temperature from 30 K at ambient pressure to 130 K at 41.2 GPa resulting from Ruderman–Kittel–Kasuya–Yosida (RKKY) interactions likely attributes to the stronger Eu–Sn interaction at high pressure. These rich results demonstrate that EuSn 2 P 2 is an ideal platform to study the correlation of the enhanced RKKY interactions, disordered lattice, intermediate valence, and topological state.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Filtration of Hanford Tank 241-AW-105 Supernatant at 16 °C

Approximately 9 L of supernatant from Hanford waste tank 241-AW-105 was delivered by Hanford Tank Waste Operations and Closure (H2C) to the Radiochemical Processing Laboratory (RPL) at Pacific Northwest National Laboratory (PNNL). The thirty-six 241-AW-105 sample bottles consisted of four sets of nine samples, with each set pulled from a unique tank sampling level. Prior to testing, samples from each level were composited and diluted to 5.5 M Na to provide nominally level-independent feed for dead-end filtration and ion exchange testing. The composited 241-AW-105 supernatant was chilled to 16 °C for 1 week prior to testing. Filtration testing was then conducted using a backpulse dead-end filter (BDEF) system equipped with a feed vessel and a Mott inline filter (Model 6610, Media Grade 5) in the hot cells of the RPL. The purpose of this testing was to (a) demonstrate dead-end filtration (DEF) of 241-AW-105 feed at reduced temperature to obtain prototypic Tank Side Cesium Removal (TSCR) flux rates and identify issues that may impact filtration after dilution to 5.5 M Na, and (b) provide feed for follow-on ion exchange unit operation. The feed was filtered through the BDEF system at a targeted flux of 0.065 gpm/ft2. For most of the filtration campaign, the differential pressure required to effect filtration at 0.065 gpm/ft2 was slow to increase. After all the feed bottles had been pumped into the slurry reservoir, the bottoms of the bottles were added to the reservoir and transmembrane pressure (TMP) reached 2.0 psid (the TSCR action limit). A backpulse was performed after >50 hours of filtration to remove fouled solids and reduce the TMP. The filter was cleaned after completing filtration of the 241-AW-105 feed, and clean water flux tests showed filter performance was effectively restored. Solids concentrated from the backpulse solutions were composed of steel-like particles, uranium-bearing phases, Mn-Fe phases, a Ce-bearing phase, Zr phases, and some smaller Ca-bearing particles. The Ca-bearing and U bearing phases were identified as calcite and clarkeite, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Effect of outer divertor leg detachment on the high field side scrape-off layer in DIII-D and ASDEX Upgrade

In this work, evidence is presented that detachment of the outer divertor leg leads to a reduction of electron density and neutral pressure in the high-field side (HFS) scrape-off layer (SOL) of the ASDEX Upgrade (AUG) and DIII-D tokamaks with ion $B$ x $∇B$ drift directed toward the X-point (favorable configuration). These results are observed across multiple diagnostics and without the use of impurity seeding to reach detachment. In AUG, outer divertor leg detachment correlates with a decrease in electron density near the separatrix at the inner midplane, measured with HFS reflectometry. A concurrent reduction in inner divertor density and neutral pressure at the inner target is observed using divertor Thomson scattering and neutral pressure gauges. These effects are present in both L- and H-mode plasmas. In DIII-D, a similar reduction is detected through analysis of line-integrated hydrogenic emission measured by multiple diagnostics in the HFS SOL close to the separatrix. The consistent trends in both devices indicate that high electron density and strong hydrogenic emissivity in the HFS SOL are common features of H-mode plasmas in the favorable configuration, independent of wall material and divertor geometry. In L-mode plasmas, the reduction in electron density and neutral pressure is not observed in DIII-D, possibly due to differences in wall material. These results emphasize the importance of the divertor state in determining the two-dimensional neutral distribution and edge fueling.

detachment↗
DOE OSTI2022

Wellbore cement fracture permeability as a function of confining stress and pore pressure

Cemented annulus fractures are a major leakage path in a wellbore system, and their permeability plays an important role in the behavior of fluid flow through a leaky wellbore. The permeability of these fractures is affected by changing conditions including the external stresses acting on the fracture and the fluid pressure within the fracture. Laboratory gas flow experiments were conducted in a triaxial cell to evaluate the permeability of a wellbore cement fracture under a wide range of confining stress and pore pressure conditions. For the first time, an effective stress law that considers the simultaneous effect of confining stress and pore pressure was defined for the wellbore cement fracture permeability. Here the results showed that the effective stress coefficient (λ) for permeability increased linearly with the Terzaghi effective stress ( -p) with an average of λ = 1 in the range of applied pressures. The relationship between the effective stress and fracture permeability was examined using two physical-based models widely used for rock fractures. The results from the experimental work were incorporated into numerical simulations to estimate the impact of effective stress on the interpreted hydraulic aperture and leakage behavior through a fractured annular cement. Accounting for effective stress-dependent permeability through the wellbore length significantly increased the leakage rate at the wellhead compared with the assumption of a constant cemented annulus permeability.

58 GEOSCIENCES↗
DOE OSTI2024

Comprehensive parametric study of CO 2 sequestration in deep saline aquifers

Carbon dioxide injection in deep saline aquifers is a key method for permanently sequestering anthropogenic CO 2 . Here this study employs a reactive transport model to explore mineral precipitation/dissolution and its impact on reservoir properties in deep saline aquifers. We also assess capillary pressure and relative permeability hysteresis on various CO 2 trapping mechanisms. Results from this study reveal the significant influence of initial brine composition on mineral precipitation/dissolution. The dissolution and precipitation of minerals have different effects around the wellbores compared to the overall reservoir. Additionally, salt concentration (Ca ++ and Mg ++ ) and quartz surface area affect CO 2 mineralization, while Na + impacts halite precipitation, altering flow properties. The effect of capillary pressure is significant, as including the capillary pressure in the simulation case resulted in significantly improved CO 2 trapping, achieving almost total dissolution of the injected CO 2 in around 300 years. This study offers novel insights into the interactions of reservoir minerals, brine properties, and the injected CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Anomalous temperature-dependent magnetization in the nearly collinear antiferromagnet Y 2 Co 3

Y 2 Co 3 is a newly discovered antiferromagnetic (AFM) compound with distorted kagome layers. Here, previous investigations via bulk magnetization measurements suggested a complex non-collinear magnetic behavior, with magnetic moments primarily anti-aligned along the b axis and some canting towards the ac plane. In this study, we report the magnetic structure of Y 2 Co 3 to be an A-type AFM structure with ferromagnetic (FM) interactions within the distorted kagome plane and an inter-plane antiferromagnetic interaction, as determined by single crystal neutron diffraction. The magnetic moments align along the b axis, with minimal canting towards the c axis, at odds with the previous interpretation of bulk magnetization measurements. The magnetic moments on the two distinct Co sites are (0, -0.68, 0) μB and (0, 1.25, 0.07) μ B . We attribute the previously reported ”non-collinear” behavior to the considerable temperature dependence of itinerant AFM exchange interactions, induced by thermal contraction along the b axis. Additionally, our examination of lattice constants through pressure studies reveals compensating effects on FM and AFM interactions, resulting in negligible pressure dependence of T N .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Room Return Path Sensitivity

Standard practice for HVAC return design has evolved from running a dedicated return to each room with a supply, to systems with returns in more centrally located areas of the home with jump ducts, transfer grilles, or simply door undercuts used as return air pathways from isolated rooms. In these latter systems, hallways and stairwells act as large open ducts for conveying air back to a single (or sometimes multiple) central return. When partition doors to an isolated room are closed, the return airflow resistance goes up, significantly impacting airflow balance if an adequate relief pathway is not installed. Airflow imbalances can lead to comfort and building durability issues and increased envelope leakage. To combat this, some jurisdictions have requirements for return air pathways. The supply system topology–or layout–impacts the airflow balance stability in response to adjustments of return pathway resistances. Branching supply topologies typically have reduced static pressure after each split. The static pressure at the final split will be lower than the primary supply plenum. Because of this, if there is a restriction in a room’s return path, supply airflow will tend to redistribute to adjacent ducts at the end of the branch. A properly designed trunk and branch supply system can effectively equalize static pressure by reducing the cross sectional area after each takeoff . Maintaining static pressure within the trunk will reduce the system’s sensitivity to changes in return paths. However, in practice, it is difficult to design and time consuming to install a complex supply plenum. Velocity effects and poor takeoff placement also impact airflow balance. This report considers return systems in three main categories: distributed, with a return duct to each room; multiple central, with one return grille on each floor of a home; and single central, with a single return grille located near the air handling unit. Three supply categories are also considered: radial splitter box, trunk and branch, and home-run with all ducts connecting directly to a central manifold.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Designing for Supply and Return Air System Interaction in Residential Buildings

Standard practice for HVAC return design has evolved from running a dedicated return to each room with a supply, to systems with returns in more centrally located areas of the home with jump ducts, transfer grilles, or simply door undercuts used as return air pathways from isolated rooms . In these latter systems, hallways and stairwells act as large open ducts for conveying air back to a single (or sometimes multiple) central return. When partition doors to an isolated room are closed, the return airflow resistance goes up, significantly impacting airflow balance if an adequate relief pathway is not installed. Airflow imbalances can lead to comfort and building durability issues and increased envelope leakage. To combat this, some jurisdictions have requirements for return air pathways. The supply system topology – or layout - impacts the airflow balance stability in response to adjustments of return pathway resistances. Branching supply topologies typically have reduced static pressure after each split. The static pressure at the final split will be lower than the primary supply plenum. Because of this, if there is a restriction in a room’s return path, supply airflow will tend to redistribute to adjacent ducts at the end of the branch. A properly designed trunk and branch supply system can effectively equalize static pressure by reducing the cross sectional area after each takeoff . Maintaining static pressure within the trunk will reduce the system’s sensitivity to changes in return paths. However, in practice, it is difficult to design and time consuming to install a complex supply plenum. Velocity effects and poor takeoff placement also impact airflow balance. This fact sheet considers return systems in three main categories: distributed, with a return duct to each room; multiple central, with one return grille on each floor of a home; and single central, with a single return grille located near the air handling unit. Three supply categories are also considered: radial splitter box, trunk and branch, and home-run with all ducts connecting directly to a central manifold. A complete description of the modeling work and results can be found in the companion technical report.

buildings↗
DOE OSTI2023

On the Thermodynamic Condition for Adsorption Azeotropes

Adsorption azeotropy is a common phenomenon in mixed-gas adsorption equilibria. Since the first literature report of binary adsorption azeotropes in 1933, numerous studies investigated the thermodynamic conditions for adsorption azeotropes but failed to reach definitive conclusions. Based on the generalized Langmuir isotherm model for multicomponent adsorption equilibria which takes into account the vacant site as part of the adsorbed phase, this study presents the thermodynamic condition for adsorption azeotropes as derived from the generalized Langmuir isotherm to be the equality of the ratios of adsorbed phase activity coefficient γi and adsorption equilibrium constant $K$$^{o}_{i}$ for the two adsorbates in the binary 1–2 adsorption system, i.e., γ 1 /$K$$^{o}_{1}$ = γ 2 /$K$$^{o}_{2}$. This adsorption azeotropic condition is analogous to the vapor–liquid equilibrium azeotropic condition, i.e., the equality of the products of liquid phase activity coefficient and saturation vapor pressure Pisat for the two components, i.e., γ 1 $P$$^{sat}_{1}$ = γ 2 $P$$^{sat}_{2}$. We validated the thermodynamic condition for adsorption azeotropes with 14 azeotrope-forming adsorption systems in this study. As a result, we investigated the effects of the pressure, temperature, and adsorbed phase nonideality on azeotrope formation.

42 ENGINEERING↗
DOE OSTI2024

Pressure induced modification of electronic and magnetic properties of MnCrNbAl and MnCrTaAl

Spin-gapless semiconductor (SGS) is a new class of material that has been studied recently for potential applications in spintronics. This material behaves as an insulator for one spin channel, and as a gapless semiconductor for the opposite spin. In this work, we present results of a computational study of two quaternary Heusler alloys, MnCrNbAl and MnCrTaAl that have been recently reported to exhibit spin-gapless semiconducting electronic structure. In particular, using density functional calculations we analyze the effect of external pressure on electronic and magnetic properties of these compounds. It is shown that while these two alloys exhibit nearly SGS behavior at optimal lattice constants and at negative pressure (expansion), they are half-metals at equilibrium, and magnetic semiconductors at larger lattice constant. At the same time, reduction of the unit cell volume has a detrimental effect on electronic properties of these materials, by modifying the exchange splitting of their electronic structure and ultimately destroying their half-metallic/semiconducting behavior. Thus, our results indicate that both MnCrNbAl and MnCrTaAl may be attractive for practical device applications in spin-based electronics, but a potential compression of the unit cell volume (e.g. in thin-film applications) should be avoided.

Materials Science↗
DOE OSTI2019

Effect of natural fractures on determining closure pressure

Abstract In Utah FORGE reservoir, eight pressure transient tests (microhydraulic fracturing and DFIT™) show natural fracture/pressure-dependent leakoff. This behavior may lead to misinterpretation of the closure pressure (proxy for minimum principal stress). The closure pressures obtained from DFIT™ (or microhydraulic fracturing) testing may reflect shear failure along natural fractures or discontinuities rather than tensile failure and lead to inaccurate estimates of the minimum principal stress. In pressure tests conducted at the Utah FORGE site showed that reactivation or opening of natural fractures intersecting the wellbore and were suggested by multiple closure events in DFIT™ tests. In addition, comparisons between the pre- and post-well-tests FMI logs show that there are populations of induced fracture and reactivated natural fractures which are mostly vertical and sub-vertical. In this study, DFIT™ (or microhydraulic fracturing) test analysis and numerical simulations were used to suggest that hydraulic shearing of critically stressed natural fractures can contribute to multiple closure signatures and possibly lead to incorrect determination of the minimum principal stress. As other authors have previously advocated, the DFIT™ test analyses and numerical simulations suggest that better estimations of minimum principal stress may be derived by injecting at relatively high rate and pressure and insuring that tensile breakdown is reached. In addition, extended shut-in period is required to determine accurate reservoir characteristics and fluid flow regime.

Nadimi, S.↗
DOE OSTI2021

Effects of turbulence-radiation coupling in pressurized oxy-combustion

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emission in power generation. Due to the strong impact of pressure on thermal radiation, heat transfer in POC differs significantly from the situation of conventional atmospheric pressure combustion. Thus thermal radiation in POC needs to be investigated to aid new combustor development. The present computational work is a step in this direction, initiating a systematic analysis of thermal radiation and heat transfer in a pilot-scale POC combustor, which has been developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. While most previous computational works on flame radiation focused on atmospheric pressure condition, this work considered a pressurized flame. Specifically, a 15-bar POC combustor of power 50 kW is modeled employing the Ansys FLUENT commercial platform, using both Reynolds-averaged Navier-Stokes (RANS) modeling and large-eddy simulation (LES). A recently published and validated global radiation model is used to predict the radiative property of the flue gas. The discrete ordinates (DO) radiation model is chosen to solve the radiative transport equation. Incident radiation on the walls of the combustor is identified and investigated. It is revealed that for this pilot-scale, pressurized combustor, thermal radiation exhibits similar patterns in the RANS and LES models. However, the magnitudes of radiation are different in both models, presumably because interactions between radiation and turbulence are embedded in the LES model but not in the RANS model. This difference thereby underlines the major goal of this research: investigating the impact of such turbulence-to-radiation coupling on thermal radiation in a pilot-scale POC setting. Most previous studies on turbulence-to-radiation interactions focused on bench-scale, atmospheric pressure flames. This work is the first effort to extend this study to a pilot-scale, pressurized flame.

Li, Lei↗
DOE OSTI2022

Utah FORGE 5-2615: Well 58-32 and 78-32 Poroelastic Properties

Lab data on permeability, grain bulk modulus, drained bulk modulus, Skempton's pore pressure coefficient, and Biot's effective stress coefficient for Utah Forge Well 58-32 and Well 78-32. Work done as part of project number 5-2615 by the University of Oklahoma.

15 GEOTHERMAL ENERGY↗
DOE OSTI2026

Metrology for femtosecond pulsed x-ray heating in diamond anvil cell experiments at the European XFEL: Revisiting the iron phase diagram up to 150 GPa

The development of pulsed intense x-ray sources, such as free electron laser, offers new avenues for high pressure experiments. Here, we study the feasibility and metrology of x-ray heating in diamond anvil cells at the European x-ray free electron laser. This method enables one to volumetrically heat the sample while inhibiting chemical migration and probing the crystallographic structure of the sample throughout the heating with a high repetition rate. We focus our study on iron, whose phase diagram is well established up to 100 GPa, to explore the possibilities and limitations of this technique. We volumetrically heat iron samples at starting pressures ranging from 10 to 138 GPa, using the x-ray beam pulsed at 4.5 MHz in a serial pump-and-probe experimental design. Experimental challenges arise from temperature gradients within the sample, changes in temperature at the 100 ns timescale, the difficulty of direct temperature estimates, the effect of thermal pressure, and the presence of metastable crystallites due to rapid cycles of heating and cooling. Hence, we develop a multi-crystal-like data processing method that allows us to account for sample heterogeneity in probed conditions. We then calibrate our measurements using known physical properties of iron under pressure. Thermal pressure in our experiments increases from 4% of the isochoric prediction at 10 GPa to 23% at 138 GPa, and we show that our data are in agreement with most previous observations of iron in this pressure range. The method can now be implemented at higher pressures and temperatures and on materials with unknown phase diagrams.

Materials science↗
DOE OSTI2023

On the relationship between the multi-region relaxed variational principle and resistive inner-layer theory

We show that the variational energy principle of the multi-region relaxed magnetohydrodynamic (MRxMHD) model can be used to predict finite-pressure linear tearing instabilities. In this model, the plasma volume is sliced into sub-volumes separated by 'ideal interfaces', and in each volume the magnetic field relaxes to a Taylor state, where the pressure gradient $\nabla p = 0$. The MRxMHD model is implemented in the Stepped-Pressure Equilibrium Code (SPEC) so that the equilibrium solution in each region is computed while preserving the force balance across the interfaces. As SPEC computes the Hessian matrix (a discretized stability matrix), the stability of an MRxMHD equilibrium can also be computed with SPEC. In this article, using SPEC, we investigate the effect of local pressure gradients and the $\nabla p = 0$ in the vicinity of the resonant surface of a tearing mode. For low-beta plasma, we have been able to illustrate a relationship between the resistive singular-layer theory (Coppi et al 1966 Nucl. Fusion6 101; Glasser et al 1975 Phys. Fluids18 875–88) and the MRxMHD model. Within the singular layer, the volume-averaged magnetic helicity and the flux-averaged toroidal flux are shown to be the invariants for the linear tearing modes in SPEC simulations. Our technique to compute MRxMHD stability is first tested numerically in a cylindrical tokamak and its application in toroidal geometry is demonstrated. We demonstrate an agreement between the stability boundary obtained with SPEC simulation and the resistive inner-layer theories.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Support of the Development of EPP Plus SMT Design Method (FY2020 Test Results)

Experiments in support of the development of the integrated Elastic–Perfectly Plastic (EPP) analysis and Simplified Model Test (SMT) design methodology continued in FY 2020. The previously developed single-bar SMT (SBSMT) technique was successfully extended to tubular shaped Alloy 617 specimens for evaluation of the effect of primary pressure load on SMT creep-fatigue (CF) properties at 950°C. A series of pressurized SMT tests were performed with various elastic follow-up factors and strain ranges. The results show that the primary pressure load reduces the SMT CF cycles. The reduction of SMT CF life due to primary load was found to be dependent on strain ranges, elastic follow up and test temperatures. These results are crucial for verification of the EPP strain range analysis in the EPP+SMT evaluation procedure. Additionally, hold time effect on the SMT CF life cycles is a determining factor for generating the EPP+SMT CF design curves. Lack of test data in the high cycle and low strain range region results in major uncertainty in developing the design curves. In FY2020, experiments were designed, and testing started on Alloy 617 at 950°C to fill the gap in experimental data. The on-going CF and additional SMT CF with elastic follow-up at low strain ranges will generate the information needed to verify the methods for extrapolation to long hold time and finalize the EPP+SMT design method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗