Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPELLANT PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Ram acceleration from a two phase detonative system

A concept for ram acceleration is presented here, which uses a combination of a gas core and a layer of solid explosive or propellant to generate high thrust densities. The concept can be either self-synchronized or externally synchronized, and may be reusable. It has the potential to achieve very high acceleration rates, higher exit velocities and to lower the tube length requirements. Preliminary numerical simulations are presented and discussed, which show the characteristics of the flow fields. Stable conditions can be achieved for low mass loadings of solid explosive, and relatively slow combustion. Accurate knowledge of the thermo-chemical properties and the equations of state of the gas and solid components is essential for further tuning of the concept.

Cambier, Jean-Luc↗
NASA NTRSDate not supplied

Assessing Stratospheric Aerosols Contamination Due to Space Activities

The life cycle of a spacecraft starts and ends in the atmosphere: it interacts with the atmosphere right after the launch and during the atmospheric reentry when it usually mostly ablates. Both phases induce emissions of gases and solid particles, providing a source of these components in the middle atmosphere. Little is known about the exact nature, composition and effects of these emissions on the atmosphere and climate, but their impact is expected to rise as more and more orbiting satellites are launched. Ever since the years 2000, the number of space rockets launched per year has increased by a factor 3 globally. At the same time, the number of satellites launched in orbit around the Earth per year has been multiplied by about 30. One may wonder whether changes in the anthropogenic material injected in the terrestrial stratosphere can be detected and what its influence may be. In order to study the cosmic dust particles arriving on Earth, the NASA Johnson Space Center (JSC) has been systematically collecting solid dust particles from the Earth’s stratosphere by aircraft equipped with dedicated particle collectors since 1981. So far, 25 catalogs have been published, covering campaigns of collection from 1981 to 2020, with a total of 5071 solid particles that have been preliminary characterized and curated. In this work, we use the preliminary classification of the dust particles. Based on SEM images and X-ray EDS composition the collected dust is separated into four groups: C (Cosmic), TCN (Terrestrial Contaminant Natural), TCA (Terrestrial Contaminant Artificial) and AOS (Aluminum Oxide Sphere). The AOS being mostly generated by solid rocket propellant, they also belong to the TCA class. Our analysis of the data published indicates that from 1980 to 2009 the cosmic dust particles typically represent on average 40% of the collection with TCA and TCN corresponding to about 30% each. In the recent years, the TCA fraction has doubled to about 60% of the collection (2010-2020). This increase in anthropogenic particles is likely due to the overall human space activity and its recent increase. We will present the properties of the solid stratospheric dust particles collected and their evolution with time. Future work will be dedicated to better classify the natural and anthropogenic particles collected and described in the existing databases. We will use numerical modelling to produce quantitative estimates of the injected mass, the lifetime of particles in the middle atmosphere (stratosphere) and the relative abundance of the anthropogenic particles with respect to the stratospheric background particle population.

J Lasue↗
NASA NTRS1993

Performance characteristics of LOX-H2, tangential-entry, swirl-coaxial, rocket injectors

Development of a high performing swirl-coaxial injector requires an understanding of fundamental performance characteristics. This paper addresses the findings of studies on cold flow atomic characterizations which provided information on the influence of fluid properties and element operating conditions on the produced droplet sprays. These findings are applied to actual rocket conditions. The performance characteristics of swirl-coaxial injection elements under multi-element hot-fire conditions were obtained by analysis of combustion performance data from three separate test series. The injection elements are described and test results are analyzed using multi-variable linear regression. A direct comparison of test results indicated that reduced fuel injection velocity improved injection element performance through improved propellant mixing.

Howell, Doug↗
NASA NTRS1987

A theoretical evaluation of laser-sustained plasma thruster performance

An extensive numerical experiment has been conducted to evaluate rocket thruster performance using a laser-sustained hydrogen plasma as the propellant. The plasma was sustained using a 30 kW CO2 laser beam operated at 10.6 microns focused inside the thruster. The steady-state Navier-Stokes equations coupled with the laser power absorption process have been solved numerically. A pressure based Navier-Stokes solver using body-fitted coordinate was used to calculate the laser-supported rocket flow which included both recirculating and transonic flow regions. The local thermodynamic equilibrium (LTE) assumption was used for the plasma thermophysical and optical properties. Geometric ray tracing was adopted to describe the laser beam. Several different throat size thrusters operated at 150 and 300 kPa chamber stagnation pressure were studied. It was found that the thruster performance (vacuum specific impulse) was highly dependent on the operating conditions, and a properly designed laser supported thruster can attain a specific impulse around 1500 secs. The heat loading on the thruster wall was also estimated and was in the range of that for a conventional chemical rocket.

Jeng, San-Mou↗
NASA NTRS2018

A Technology Architecture for Accessing the Oceans of Icy Worlds

The icy moon oceans beckon with ingredients that potentially may harbour extant life. Beginning with the Galileo and Cassini missions, measurements have revealed the presence of global oceans under the icy crust of several moons of Jupiter and Saturn. Among those moons, Europa and Enceladus have their ocean in contact with the rocky core, providing an environment similar to the conditions existing on the terrestrial sea-floor where life has developed at hydrothermal vents Accessing these oceans presents considerable difficulty due to a number of issues including the depth and composition of the icy crust, the time needed to travel through the crust, the power needed to propel a probe, communication of scientific and engineering data though the ice and back to Earth, entry and mobility in the ocean and autonomous operations for the life of the mission. A detailed trade space study was conducted to develop a technology architecture defining a system that would access an icy moon’s ocean. To specifically bound the architecture, Jupiter’s moon Europa was chosen as the target body though the work can apply to other bodies. The current understanding of the scientific properties of the ice crust and ocean was used to guide the development. A strawman scientific payload was devised to further develop a baseline set of requirements. Beginning with a launch and trajectory that can bring a system to Europa’s orbit, a complete trade space was developed outlining the engineering systems needed to access the ocean. The architecture was divided into specific phases for i) deorbit, descent and landing, ii) surface operations, iii) ice descent and iv) ocean access. The technical maturity of each of sub-system for the phases was assessed for systems that could be developed to a maturity ready for a preliminary design in less than ten years. Integrated system parameters on power, communication capacity, and mass were developed to further define the overall system. To constrain the design, a total time in the ice, from the ice crust surface to accessing the ocean was limited to three years, and 15Km of ice was baselined with a temperature profile through the ice estimated from the scientific literature.

Sengupta, Anita↗
NASA NTRS1989

Electrostatic Plasma Accelerator (EPA)

The Electrostatic Plasma Accelerator (EPA) is a thruster concept which promises specific impulse levels between low power arcjets and those of the ion engine while retaining the relative simplicity of the arcjet. The EPA thruster produces thrust through the electrostatic acceleration of a moderately dense plasma. No accelerating electrodes are used and the specific impulse is a direct function of the applied discharge voltage and the propellant atomic mass. The goal of the present program is to demonstrate feasibility of the EPA thruster concept through experimental and theoretical investigations of the EPA acceleration mechanism and discharge chamber performance. Experimental investigations will include operating the test bed ion (TBI) engine as an EPA thruster and parametrically varying the thruster geometry and operating conditions to quantify the electrostatic plasma acceleration effect. The theoretical investigations will include the development of a discharge chamber model which describes the relationships between the engine size, plasma properties, and overall performance. For the EPA thruster to be a viable propulsion concept, overall thruster efficiencies approaching 30% with specific impulses approaching 1000 s must be achieved.

Brophy, John R.↗
NASA NTRS2016

Extraterrestrial Regolith Derived Atmospheric Entry Heat Shields

High-mass planetary surface access is one of NASAs technical challenges involving entry, descent and landing (EDL). During the entry and descent phase, frictional interaction with the planetary atmosphere causes a heat build-up to occur on the spacecraft, which will rapidly destroy it if a heat shield is not used. However, the heat shield incurs a mass penalty because it must be launched from Earth with the spacecraft, thus consuming a lot of precious propellant. This NASA Innovative Advanced Concept (NIAC) project investigated an approach to provide heat shield protection to spacecraft after launch and prior to each EDL thus potentially realizing significant launch mass savings. Heat shields fabricated in situ can provide a thermal-protection system for spacecraft that routinely enter a planetary atmosphere. By fabricating the heat shield with space resources from materials available on moons and asteroids, it is possible to avoid launching the heat-shield mass from Earth. Regolith has extremely good insulating properties and the silicates it contains can be used in the fabrication and molding of thermal-protection materials. In this paper, we will describe three types of in situ fabrication methods for heat shields and the testing performed to determine feasibility of this approach.

Heat↗
NASA NTRSDate not supplied

Conceptual Design of a Test Section for a Cryogenic Transfer Line Experiment

This project presents the development of a comprehensive computer-aided design (CAD) model for the Transfer Line test section, which is an upcoming test module for the Flow Boiling and Condensation Experiment (FBCE) aboard the International Space Station. The FBCE aims to serve as the primary platform to study two-phase flow in microgravity, and the Transfer Line module aims to utilize its existing hardware to study cryogenic chilldown; a critical component of cryogenic propellant transfer in space. The CAD model was created using SolidWorks software and includes the test section’s main components: a heat transfer line, a flow visualization line, insulation, high-speed visible imaging, and infrared imaging. The heat transfer line primarily consists of a stainless steel tube that will be heated via Joule heating. The flow visualization line consists of segmented Indium-Titanium-Oxide coated sapphire tubes, which allow for visualization of flow regimes by high-speed and infrared cameras, similar thermal properties as the stainless steel tube, and Joule heating via the ITO coating resistance. Polyether Ether Ketone was used to insulate and encapsulate the two sections. High-speed visible imaging and infrared imaging were also incorporated to view the propagation of fluid during inverted annular flow and map out the thermal profile of the ITO-coated sapphire tube. This model serves as the guiding concept design for the Transfer Line project and will assist the project team during future safety reviews and concept design reviews. Overall, this work is significant in two-phase flow research and offers a promising path towards an established facility for cryogenic transfer line research in microgravity.

Flow boiling↗
NASA NTRS1993

Ignition and combustion of lunar propellants

The ignition and combustion of Al, Mg, and Al/Mg alloy particles in 99 percent O2/1 percent N2 mixtures is investigated at high temperatures and pressures for rocket engine applications. The 20 micron particles contain 0, 5, 10, 20, 40, 60, 80, and 100 weight percent Mg alloyed with Al, and are ignited in oxygen using the reflected shock in a shock tube near the endwall. Using this technique, the ignition delay and combustion times of the particles are measured at temperatures up to 3250 K as a function of Mg content for oxygen pressures of 8.5, 17, and 34 atm. An ignition model is developed which employs a simple lumped capacitance energy equation and temperature and pressure dependent particle and gas properties. Good agreement is achieved between the measured and predicted trends in the ignition delay times. For the particles investigated, the contribution of heterogeneous reaction to the heating of the particle is found to be significant at lower temperatures, but may be neglected as gas temperatures above 3000 K. As little as 10 percent Mg reduces the ignition delay time substantially at all pressures tested. The particle ignition delay times decrease with increasing Mg content, and this reduction becomes less pronounced as oxidizer temperature and pressure are increased.

Burton, Rodney L.↗
NASA NTRS1990

Numerical modeling of an arcjet thruster

A numerical model of an arcjet thruster was developed and the results of calculations using this model are compared to the experimental data from a 30 kW arcjet using ammonia as a propellant. The model contains equations for the conservation of mass, radial, axial, and azimuthal momentum, energy, and the radial component of the magnetic field and provides a solution for three components of velocity, temperature, and the axial and radial current as a function of position in an axisymmetric flowfield. The model predicts 12 percent more specific impulse than the experiment when the mass flow and power input are constrained to the experimental values. A major conclusion of this study is that improved procedures for calculating transport properties are necessary if the accuracy of the model is to be improved.

Rhodes, Robert P.↗
NASA NTRS2003

Hydrogen Permeability of a Polymer Based Composite Tank Material Under Tetra-Axial Strain

In order to increase the performance of future expendable and reusable launch vehicles and reduce per-pound payload launch costs, weight reductions have been sought in vehicle components. Historically, the cryogenic propellant tanks for launch vehicles have been constructed from metal. These are some of the largest structural components in the vehicle and contribute significantly to the vehicles total dry weight. A successful replacement material will be conformable, have a high strength to weight ratio, and have a low gas-permeability to the cryogens being stored, i.e., oxygen and hydrogen. Polymer-based composites are likely candidates to fill this role. Polymer and polymer-based composites in general are known to have acceptable gas permeation properties in their as-cured state.1 The use of polymer-based composites for this application has been proposed for some time.2 Some successes have been reported with oxygen3, but other than the DC-XA experience, those with hydrogen have been limited. The primary reason for this has been the small molecular diameter of hydrogen, the lower temperatures of the liquid, and that the composite materials examined to date have all been susceptible to microcrack formation in response to the thermal-mechanical cycles experienced in the use-environment. There have been numerous accounts of composite materials with reported acceptable resistance to the formation of microcracks when exposed to various mechanical and/or thermal cycles. However, virtually all of these studies have employed uniaxial loads and there has been no discussion or empirical evidence pertaining to how these loads relate to the biaxial state of stress in the material in its use environment. Furthermore, many of these studies have suffered from a lack of instrument sensitivity in detecting hydrogen permeability, no standards, insufficient documentation of test conditions, testing of cycled materials in their unload state, and/or false assumptions about the nature of the microcracks in the material. This paper documents the results of hydrogen permeability testing on a Bismaleimide (BMI) based graphite fiber composite material under a variety of tetra-axial strain states.

Stokes, Eric H.↗
NASA NTRS2007

Influence of Initial Vorticity Distribution on Axisymmetric Vortex Breakdown and Reconnection

An analytical treatment has been developed to study some of the axisymmetric vortex breakdown and reconnection fluid dynamic processes underlying body-vortex interactions that are frequently manifested in rotorcraft and propeller-driven fixed-wing aircraft wakes. In particular, the presence of negative vorticity in the inner core of a vortex filament (one example of which is examined in this paper) subsequent to "cutting" by a solid body has a profound influence on the vortex reconnection, leading to analog flow behavior similar to vortex breakdown phenomena described in the literature. Initial vorticity distributions (three specific examples which are examined) without an inner core of negative vorticity do not exhibit vortex breakdown and instead manifest diffusion-like properties while undergoing vortex reconnection. Though this work focuses on laminar vortical flow, this work is anticipated to provide valuable insight into rotary-wing aerodynamics as well as other types of vortical flow phenomena.

Young, Larry A.↗
NASA NTRS1939

Full-Scale Wind-Tunnel Investigation of Wing-Cooling Ducts Effects of Propeller Slipstream, Special Report

The safety of remotely operated vehicles depends on the correctness of the distributed protocol that facilitates the communication between the vehicle and the operator. A failure in this communication can result in catastrophic loss of the vehicle. To complicate matters, the communication system may be required to satisfy several, possibly conflicting, requirements. The design of protocols is typically an informal process based on successive iterations of a prototype implementation. Yet distributed protocols are notoriously difficult to get correct using such informal techniques. We present a formal specification of the design of a distributed protocol intended for use in a remotely operated vehicle, which is built from the composition of several simpler protocols. We demonstrate proof strategies that allow us to prove properties of each component protocol individually while ensuring that the property is preserved in the composition forming the entire system. Given that designs are likely to evolve as additional requirements emerge, we show how we have automated most of the repetitive proof steps to enable verification of rapidly changing designs.

Nickle, F. R.↗
NASA NTRS1977

Shock compression and adiabatic release of a titaniferous mare basalt

A report is presented regarding the dynamic properties of a rock indigenous to the mare basins of the moon. The reported data were obtained in a study of sample 70215, a very titanium-rich basalt (58% pyroxene, 18% ilmenite, 15% plagioclase, 6% olivine, and 3% quartz by weight). This rock is probably representative of a class of the earliest mare-filling extrusive rocks which are exposed on the present lunar surface. Two series of experiments were performed. One set of experiments involved the measuring of Hugoniot and release adiabats to 15.7 GPa with a propellant gun apparatus. In the second set of experiments, a light-gas gun was employed to yield Hugoniot data at about 120 GPa and release states at about 90 GPa. Lunar basalt 70215 appears to be among the densest rocks in the present lunar sample collection, having a crystal density of 3.38 g/cu cm and a porosity of about 1.3%. The results of the experiments have important implications for both the degree of shock metamorphism expected for impact processes and the extent of ejecta transport on mare surfaces with high-titanium basalt composition.

Ahrens, T. J.↗
NASA NTRS1989

The measurement, modeling, and prediction of traction for rocket propellant 1

Traction tests were performed on RP-1, a common kerosene based rocket propellant. Traction data on this fluid are required for purposes of turbopump bearing design, using codes such as SHABERTH. To obtain the traction data, an existing twin disc machine was used, operating under the side slip mode and using elliptical contacts. The range of test variables were: contact peak Hertz stress from 1.0 to 2.0 GPa, disc surface speed from 10 to 50 m/s, fluid inlet temperature from 30 to 70 C, and with a contact aspect ratio of 1.7. The resulting traction curves were reduced to fundamental fluid property parameters using the Johnson and Tevaarwerk traction model. Theoretical traction predictions were performed by back substitution of the fundamental properties into the traction model. Comparison of the predicted with the measured curves gives a high degree of confidence in the correctness of the traction model. For purposes of input to the NASA SHABERTH program, the traction model was next used to predict the expected traction of RP-1 under line contact conditions.

Tevaarwerk, J. L.↗
NASA NTRS2000

Thermophysics Characterization of Kerosene Combustion

A one-formula surrogate fuel formulation and its quasi-global combustion kinetics model are developed to support the design of injectors and thrust chambers of kerosene-fueled rocket engines. This surrogate fuel model depicts a fuel blend that properly represents the general physical and chemical properties of kerosene. The accompanying gaseous-phase thermodynamics of the surrogate fuel is anchored with the heat of formation of kerosene and verified by comparing a series of one-dimensional rocket thrust chamber calculations. The quasi-global combustion kinetics model consists of several global steps for parent fuel decomposition, soot formation, and soot oxidation, and a detailed wet-CO mechanism. The final thermophysics formulations are incorporated with a computational fluid dynamics model for prediction of the combustor efficiency of an uni-element, tri-propellant combustor and the radiation of a kerosene-fueled thruster plume. The model predictions agreed reasonably well with those of the tests.

Wang, Ten-See↗
NASA NTRS1990

Rendezvous with a star

The spacecraft Ulysses carrying five European and four American instruments is described. The instruments are designed to investigate the properties of the solar wind, the sun-wind interface, the heliospheric magnetic field, solar radio burst and plasma waves, solar X-rays, solar and galactic cosmic rays, and gas and dust in interplanetary space. Ulysses is scheduled to be carried into orbit aboard the Space Shuttle in October 1990, when Jupiter's position relative to the earth is suitable for a minimum-energy trajectory. Once in orbit, a three-stage, solid-fuel vehicle known as the Inertial Upper Stage plus Payload Assist Module (Special), will then propel Ulysses on a 16-month journey to Jupiter. In February 1992, Ulysses is scheduled to fly past Jupiter toward its rendezvous with the sun. Ulysses will then head for a region of interplanetary space never before explored and is scheduled to have two solar encounters. Its official mission ends soon after September 1995.

Bennett, Gary L.↗
NASA NTRS1992

Combustion instability analysis for liquid propellant rocket engines

The multi-dimensional numerical model has been developed to analyze the nonlinear combustion instabilities in liquid-fueled engines. The present pressure-based approach can handle the implicit pressure-velocity coupling in a non-iterative way. The additional scalar conservation equations for the chemical species, the energy, and the turbulent transport quantities can be handled by the same predictor-corrector sequences. This method is time-accurate and it can be applicable to the all-speed, transient, multi-phase, and reacting flows. Special emphasis is given to the acoustic/vaporization interaction which may act as the crucial rate-controlling mechanism in the liquid-fueled rocket engines. The subcritical vaporization is modeled to account for the effects of variable thermophysical properties, non-unitary Lewis number in the gas-film, the Stefan flow effect, and the effect of transient liquid heating. The test cases include the one-dimenisonal fast transient non-reacting and reacting flows, and the multi-dimensional combustion instabilities encountered in the liquid-fueled rocket thrust chamber. The present numerical model successfully demonstrated the capability to simulate the fast transient spray-combusting flows in terms of the limiting-cycle amplitude phenomena, correspondence between combustion and acoustics, and the steep-fronted wave and flame propagation. The investigated parameters include the spray initial conditions, air-fuel mixture ratios, and the engine geometry. Stable and unstable operating conditions are found for the liquid-fueled combustors. Under certain conditions, the limiting cycle behavior of the combusting flowfields is obtained. The numerical results indicate that the spray vaporization processes play an important role in releasing thermal energy and driving the combustion instability.

Kim, Y. M.↗