The part-through surface crack in an elastic plate
Elastic plate with part-through surface crack, determining stress intensity factor for remote tensile and bending loads
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Elastic plate with part-through surface crack, determining stress intensity factor for remote tensile and bending loads
Crack wave loading, investigating dynamic stress intensity factor and time response with photoelastic technique
Stress intensity factors and strain energy rate for bonded layered composites with interface flaw /crack/
Stress intensity factors of periodically spaced elastic cover plates bonded to elastic half plane, solving contact problem by Fredholm integral equation
Beryllium fracture toughness test specimens were fatigue cracked using reversed cycling with a compression load two to three times the tension load. In worked beryllium, textures may be produced which result in fatigue cracks that are out of plane with the starter notch. Specimens of hot pressed stock exhibited load displacement records which were nonlinear throughout their course. Fracture specimens of both hot pressed and forged stock showed essentially no reduction of thickness and the fracture surfaces were flat and normal to the load axis. However, the stress intensity factor at maximum load increased with decreasing thickness. Load-displacement and electric potential records for the hot pressed beryllium specimens exhibited several anomalies such as negative residual crack mouth displacements and a decrease in electrical potential with increasing load.
The correlation between fatigue crack propagation and stress intensity factor is analyzed. When determining fatigue crack propagation rate, a crack increment, delta a, and its corresponding increment in load cycles, delta N, are measured. Fatigue crack propagation must be caused by a shear and/or a normal separation mode. Both of these two processes are discrete if one looks at the atomic level. If the average deformation and fracture properties over the crack increments, delta a, can be considered as homogeneous, if the characteristic discrete lengths of sigma a, if the plastic zone size is small, and if a plate is thick enough to insure a plane strain case, da/dN is proportional to delta K squared. Any deviation of empirical data from this relation must be caused by the fact that one or more of these conditions are not satisfied. The effects of plate thickness and material inhomogeneity are discussed in detail. A shear separation mode of fatigue crack propagation is described and is used to illustrate the effects of material inhomogeneity.
A description is given of a computer program for analyzing the crack propagation in cyclic loaded structures. By using equations for the stress intensity factors for surface and embedded flaws, the capability of ascertaining lengthwise crack growth as well as crack growth through the thickness of the structure was determined. Equations used are written in general form so that many other types of crack growth problems, such as through the thickness type cracks, can be analyzed. Provisions have been made in the computer program to analyze crack growth for repeated blocks of variable-amplitude fatigue load spectra. Additional features of the computer program include a variable print interval and a variable integration interval to minimize computer printout and computer run time. A source listing and instructions for using the computer program are included.
To understand the influence temperature on the rate of fatigue crack growth in high strength metal alloys, constant load amplitude, fatigue crack growth experiments were carried out using a 1/4-inch-thick (6.35 mm) mill annealed Ti-6Al-4V alloy plate as a model material. The rates of fatigue crack growth were determined as a function of temperature, ranging from room temperature to about 290 C (or, about 550 F/563K) and as a function of the crack tip stress intensity factor in a dehumidified high purity argon environment. Limited correlative experiments indicate that dehumidified oxygen and hydrogen have no effect on the rate of fatigue crack growth in this alloy, while distilled water increased the rate of crack growth slightly in the range tested. Companion fractographic examinations suggest that the mechanisms for fatigue crack growth in the various environments are essentially the same.
The problem of a laminate composite in the presence of a crack located normal to the bond lines is considered. Stress analysis of the limiting case when the crack extends to the bond lines is carried out. An integral transform technique is used to formulate the problem in terms of a singular integral equation. The power of stress singularity around the crack tip terminating at the interface is obtained using the above technique. The singular integral equation is solved numerically and the effect of material properties on the stress intensity factor is calculated.
A semi-infinite strip held rigidly on its short end is considered. Loads in the strip at infinity (far away from the fixed end) are prescribed. Integral transform technique is used to provide an exact formulation of the problem in terms of a singular integral equation. Stress singularity at the strip corner is obtained from the singular integral equation which is then solved numerically. Stresses along the rigid end are determined and the effect of the material properties on the stress intensity factor is presented. The method can also be applied to the problem of a laminate composite with a flat inclusion normal to the interfaces.
The axially symmetric elastostatic problem for a layer bonded to a half space with different material properties is considered. It is assumed that the bi-material interface contains a penny-shaped crack the surfaces of which are subjected to known tractions. The solution of the problem is reduced to that of a system of singular integral equations of the second kind. A numerical example for an aluminum-epoxy material combination is given. The stress intensity factors and the strain energy release rate are calculated and are given as functions of layer thickness-to-crack radius ratio.
The fully antisymmetric problem for a cylindrical shell with a circumferential crack is considered. The solution of the problem is reduced to that of a system of singular integral equations of the first kind. As an example the torsion of the cylinder is discussed and membrane and bending components of the stress intensity factor ratio are given.
To study the influence of temperature on the rate of fatigue crack growth in high strength metal alloys, constant load amplitude fatigue crack growth experiments were carried out using a .25-in.-thick mill annealed Ti-6Al-4V alloy plate. The rates of fatigue crack growth were determined as a function of temperature, ranging from room temperature to about 290 C, and as a function of the crack tip stress intensity factor in a dehumidified high purity argon environment. Limited correlative experiments were carried out in distilled water, dehumidified oxygen and hydrogen, and in vacuum. The results indicate that the rate of fatigue crack growth is essentially independent of test temperature in this alloy, and is affected by residual moisture in very small concentrations. Companion fractographic examinations suggest that the mechanims for fatigue crack growth in the various environments are essentially the same.
Fatigue and fracture of cylindrical and spherical shells containing a through crack and subjected to internal pressure or torsion are considered. The stress intensity factor ratios giving the effect of curvature are obtained as functions of a dimensionless shell parameter. By using the conventional plastic strip model the plastic zone size around the crack tip and the crack opening displacement are calculated. The calculated COD values are shown to be in good agreement with the experimental results. The fracture criterion of critical COD is verified by using the results of the burst tests in titanium and aluminum alloy cryogenic pressure vessels. Modified fatigue crack propagation models taking into account the bending effect in shells are introduced and are applied to the analysis of experimental data obtained from flat plates, and cylindrical shells under axial tension, internal pressure, and torsion. Finally, the paper includes the effect of humidity on the crack growth rate and the effect of load biaxiality on the rupture strength.
This paper summarizes and evaluates the work done on the elastic analysis of the surface flaw problem by the application of the alternating method. An attempt is made to describe the alternating method and to present the history of its application to the surface flaw problem and to related problems in fracture mechanics. Stress intensity factors obtained by this method are summarized and compared. Results are also compared to those obtained by investigators using other methods of analysis. An evaluation of the use of the alternating method is presented with the purpose of pointing out the advantages and disadvantages in the application of this technique to the surface flaw problem.
A mapping-collocation method was developed for the elastostatic stress analysis of finite, anisotropic plates with centrally located traction-free cracks. The method essentially consists of mapping the crack into the unit circle and satisfying the crack boundary conditions exactly with the help of Muskhelishvili's function extension concept. The conditions on the outer boundary are satisfied approximately by applying the method of least-squares boundary collocation. A parametric study of finite-plate stress intensity factors, employing this mapping-collocation method, is presented. It shows the effects of varying material properties, orientation angle, and crack-length-to-plate-width and plate-height-to-plate-width ratios for rectangular orthotropic plates under constant tensile and shear loads.
A seminumerical method is presented for three-dimensional elastic analysis of finite geometry solids with traction-free cracks. Stress and displacement distributions are calculated for two rectangular bars which are loaded by a uniform surface stress distribution. The first bar contains a through-thickness central crack while the second bar has double-edge cracks. Stress intensity factors K sub I for both configurations are presented.
A finite strip compressed between two rough rigid stamps is considered. The elastostatic problem is formulated in terms of a singular integral equation from which the proper stress singularities at the corners are determined. The singular integral equation is solved numerically to determine the stresses along the fixed ends of the strip. The effect of material properties and strip geometry on the stress intensity factor is presented graphically.