Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Structural Properties of Niobium Thin Films Deposited on Metallic Substrates by ECR

Particle accelerator technologies rely on SRF cavities to create the accelerating gradient for beam lines. Solid niobium cavities are widely employed throughout the community despite high material, fabrication, and operation cost. New thin film technologies are being explored for the suitability of niobium coatings for accelerating cavities. Thin layers of high-quality niobium would be deposited on a base material that has lower material and fabrication cost. Copper is a strong candidate for the cavity base due to availability, cost, machinability, and potentially improved performance characteristics of the niobium SRF surface. Initial results of TEM, EBSD and XRD analyses of niobium thin films grown on copper substrates under controlled conditions are presented to demonstrate the feasibility of the technology and establish lower limits of performance characteristics. Correlation of RRR data with the structure of niobium thin films will demonstrate the importance of thin film structural quality. *Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.

Spradlin, Joshua↗

Electrical and structural properties of binary Ga–Sb phase change memory alloys

Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.

Ume, Rubab (ORCID:0000000324766900)↗

Enhancement of micro structural properties of PVA doped with MWCNT’s and metal oxide nanocomposites films

WO{sub 3} nanoparticles were prepared by using precipitation method and the multiwall Carbon nanotubes (MWCNT’s) were functionalized to make Carboxylated MWCNTs. Further, prepared WO{sub 3} and carboxylated MWCNT were doped into PVA matrix by coagulation technique and PVA nanocomposites were prepared by simple solvent casting technique. The films were characterized by XRD, FTIR spectroscopy and AFM. FTIR spectroscopy reveals the intensity of absorption of radiation at 3624.55 cm{sup −1} corresponds to the OH group of PVA. It changes in accordance with dopant concentration causing inter/intra molecular hydrogen bonding between the dopants and PVA back bone which leads to the complex formation. XRD data explores the crystalline nature of the film. It is found that for doping concentration x= 7.5 wt% the percentage crystallinity and crystallite size increases whereas micro structural strain and dislocation density decreases. An atomic force microscopy topographic analysis proves that the doped particles have an average size less than 15 nm, as confirmed by XRD data. It was found that roughness of the sample varies with dopant concentration causing variation in crystallinity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural properties of compact groups

We report the results of a systematic study of galaxies in the regions of Hickson compact groups. Our sample is composed of the 22 Hickson groups which are located in the southern hemisphere and have cz less than 9000 km/s. Making use of digitized images of IIIa-J plates that cover an area of 0.5 x 0.5 deg around each group, we were able to detect and classify images down to a magnitude limit of 19.5 in the B band. This limit is typically three magnitudes fainter than previous studies. Most groups show a statistically significant excess of fainter galaxies compared to the background. These fainter galaxies typically have a somewhat more extended spatial distribution than the brighter galaxies originally classified by Hickson. Our data suggest that Hickson groups have a wide range in density and radius, ranging from very compact structures with overdensities of the order of 10(exp 2) and crossing times of roughly 0.01 H(sub 0 sup -1), to much more diffuse structures, similar to loose groups, with overdensities of about 3 and crossing times of roughly 0.5 H(sub 0 sup -1).

De Carvalho, R. R.↗

The impact of negative oxygen ion bombardment on electronic and structural properties of magnetron sputtered ZnO:Al films

In order to study the impact of negative oxygen ion bombardment on the electronic transport properties of ZnO:Al films, a systematic magnetron sputtering study from ceramic targets with excitation frequencies from DC to 27 MHz, accompanied by strongly varying discharge voltages, has been performed. Higher plasma excitation frequencies significantly improve the transport properties of ZnO:Al films. The effect of the bombardment of the films by energetic particles (negative oxygen ions) can be explained by the dynamic equilibrium between the formation of acceptor-like oxygen interstitials compensating the extrinsic donors and the self-annealing of the interstitial defects at higher deposition temperatures.

36 MATERIALS SCIENCE↗

Role of Pairwise Reactions on the Synthesis of Li 0.3 La 0.57 TiO 3 and the Resulting Structure–Property Correlations

The performance of single-ion conductors is highly sensitive to the material’s defect chemistry. Tuning these defects is limited for solid-state reactions as they occur at particle–particle interfaces, which provide a complex evolving energy landscape for atomic rearrangement and product formation. In this report, we investigate the (1) order of addition and (2) lithium precursor decomposition temperature and their effect on the synthesis and grain boundary conductivity of the perovskite lithium lanthanum titanium oxide (LLTO). We use an intimately mixed sol–gel, a solid-state reaction of Li precursor + La 2 O 3 + TiO 2 , and Li precursor + amorphous La 0.57 TiO x as different chemical routes to change the way in which the elements are brought together. The results show that the perovskite can accommodate a wide range of Li deficiencies (upward of 50%) while maintaining the tetragonal LLTO structure, indicating that X-ray diffraction (XRD) is insufficient to fully characterize the chemical nature of the product (i.e., Li-deficient LLTO may behave differently than stoichiometric LLTO). Variations in the relative intensities of different reflections in XRD suggest variations in the La ordering within the crystal structure between synthesis methods. Furthermore, the choice of the precursor and the order of addition of the reactants lower the time required to form a pure phase. Density functional theory calculations of the formation energy of possible reaction intermediates support the hypothesis that a greater thermodynamic driving force to form LLTO leads to a greater LLTO yield. Here, the retention of lithium is correlated with the thermal decomposition temperature of the Li precursor and the starting material mixing strategy. Taking the results together suggests that cations that share a site with Li should be mixed early to avoid ordering. Such cation ordering inhibits Li motion, leading to higher Li ion resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Doping effect on the structural properties of Cu{sub 1−x}(Ni, Zn, Al and Fe){sub x}O samples (0<x<0.10): An experimental and computational study

In this work, the effect of insertion of transition metal, TM (=Ni, Zn, Al and Fe), ions in Cu{sub 1−x}TM{sub x}O samples (0<x<0.10) prepared via co-precipitation method is studied through experimental and computational methods. The analyses of X-ray diffraction (XRD) patterns using Rietveld refinement show that i) at x=0, all samples present a monoclinic crystal system with space group C2/c and ii) for increasing the TM-doping, Ni and Zn-doped samples show a small amount of spurious phases for concentrations above x=0.05. Based on these results, a defect disorder study for using atomistic computational simulations which is based on the lattice energy minimization technique is employed to predict the location of the dopant ions in the structure. In agreement with XRD data, our computational results indicate that the trivalent (Al and Fe ions) are more favorable to be incorporated into CuO matrix than the divalent (Ni and Zn ions). - Graphical Abstract: The effect of insertion of transition metal, TM (=Ni, Zn, Al and Fe), ions in Cu{sub 1−x}TM{sub x}O samples (0<x<0.10) prepared via co-precipitation method is studied through experimental and computational methods. Display Omitted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing structure–property relationship in chemical vapor deposited hybrid perovskites by pressure and temperature

Chemical vapor deposition (CVD), a low-cost and a scalable deposition technique, allows the growth of methylammonium lead iodide (MAPbI 3 ) films without the use of solvents, substantially increasing air stability while also inducing the stable cubic phase at room temperature and at pressures as low as 0.25 GPa. MAPbI 3 thin films were grown by a facile two-step low-pressure vapor deposition process in a single reactor. This method results in films, which are usually in the tetragonal phase (space group: I4/mcm) and occasionally in the cubic phase under ambient conditions. High-pressure synchrotron-based X-ray diffraction studies from CVD-grown MAPbI 3 crystallites show that the sample remains in the cubic phase (space group: Im$\bar{3}$) between 0.25 and 3.0 GPa. Temperature-dependent transport measurements show sharp anomalies, correlating with the structural changes. The transport measurements from the CVD- grown cubic MAPI 3 film is further compared with a film in the tetragonal phase.

36 MATERIALS SCIENCE↗

Local metallic and structural properties of the strongly correlated metal $\mathrm{LaNiO_3}$ using $\mathrm{^8Li β-NMR}$

We report β-detected NMR of ion-implanted $\mathrm{^8Li}$ in a single crystal and thin film of the strongly correlated metal $\mathrm{LaNiO_3}$. Spin-lattice relaxation measurements reveal two distinct local environments, both metallic as evident from $T$-linear Korringa $\mathrm{1/T_1}$ below $\mathrm{200K}$ with slopes comparable to other metals. A small approximately temperature-independent Knight shift of $\mathrm{~74 ppm}$ is observed, yielding a normalized Korringa product characteristic of substantial antiferromagnetic correlations.We find no evidence for a magnetic transition from 4 to $\mathrm{310 K}$. The similarity of these features in the two very different samples indicates that they are intrinsic and unrelated to dilute oxygen vacancies. We attribute the two environments to two distinct but similar crystallographic $\mathrm{^8Li}$ sites and not to any form of phase inhomogeneity, but this is inconsistent with the conventional rhombohedral structure of $\mathrm{LaNiO_3}$, and also cannot be simply explained by the common alternative orthorhombic or monoclinic distortions.

36 MATERIALS SCIENCE↗

Synthesis, microstructure, and electronic band structure properties of nanocrystalline neodymium-doped bismuth titanate ferroelectric films fabricated by the sol–gel method

Graphical abstract: X-ray diffraction indicates that the films are polycrystalline with the pure perovskite phase. Ten Raman active modes and one silicon substrate mode can be observed. The A{sub 1} {sub g}[Bi] at about 59 cm{sup −1} is unchanged whereas the B{sub 1} {sub g} and A{sub 1} {sub g}[Ti] phonon modes shift towards higher frequencies. Photoluminescence shows that the intensities of the two peaks increase with Nd concentration except the Bi{sub 3}NdTi{sub 3}O{sub 12} film, due to the smallest grain size and oxygen vacancy defects. Good optical functions of the BNT films are achieved due to the SE suggesting potential applications in ferroelectric-based optoelectronic devices. - Abstract: Bi{sub 4−x}Nd{sub x}Ti{sub 3}O{sub 12} (BNT) films with different Nd contents (from 0 to 1 with 0.25 intervals) are prepared by the sol–gel process. The Nd substitution effects on the preferred orientation, surface morphology, phonon modes, emission bands, andelectronic band structures of the BNT films are investigated by microscopy, Raman scattering, photoluminescence, and spectroscopic ellipsometry (SE) at room temperature. X-ray diffraction indicates that the films are polycrystalline with the pure perovskite phase. Ten Raman active modes and one silicon substrate mode can be observed. The A{sub 1} {sub g}[Bi] at about 59 cm{sup −1} is unchanged whereas the B{sub 1} {sub g} and A{sub 1} {sub g}[Ti] phonon modes shift towards higher frequencies. Photoluminescence shows that the intensities of the two peaks increase with Nd concentration except the Bi{sub 3}NdTi{sub 3}O{sub 12} film, due to the smallest grain size and oxygen vacancy defects. Good optical functions of the BNT films are achieved due to the SE suggesting potential applications in ferroelectric-based optoelectronic devices.

36 MATERIALS SCIENCE↗

Influence of plasma density on the chemical composition and structural properties of pulsed laser deposited TiAlN thin films

Incorporation of substitutional Al into the TiN lattice of the ternary alloy TiAlN results in a material with improved properties compared to TiN. In this work, TiAlN thin films were grown by the simultaneous ablation of Ti and Al targets in a nitrogen containing reactive atmosphere. The deposit was formed on silicon substrates at low deposition temperature (200 °C). The dependence of the Al content of the films was studied as a function of the ion density of the plasma produced by the laser ablation of the Al target. The plasma parameters were measured by means of a planar Langmuir probe and optical emission spectroscopy. The chemical composition of the films was measured by energy dispersive X-ray spectroscopy. The results showed a strong dependence of the amount of aluminum incorporated in the films with the plasma density. The structural characterization of the deposits was carried out by Raman spectroscopy, X-ray diffraction, and transmission electron microscopy, where the substitutional incorporation of the Al into the TiN was demonstrated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Features of molecular-beam epitaxy and structural properties of AlInSb-based heterostructures

AlInSb layers are grown on highly lattice-mismatched GaAs (100) substrates by molecular-beam epitaxy (MBE) and studied in situ by reflection high-energy electron diffraction and ex situ by scanning and transmission electron microscopy (SEM and TEM). It is shown that one feature of AlInSb/GaAs heterostructure features is a high probability of forming microtwins; methods for decreasing their concentration are proposed. To initiate AlInSb growth on GaAs substrates under high lattice-mismatch ({approx}14.5%) conditions and to stimulate the transition to 2D growth, the GaAs layer surface was preliminarily exposed to an antimony flux followed by deposition of an intermediate AlSb buffer layer. The optimization of initial MBE growth stages of Sb-containing layers on the GaAs surface allows a decrease in the defect density in the GaAs/AlInSb heterostructures more than by two orders of magnitude, including a drastic decrease in the microtwin density. Optimal MBE growth conditions for Al{sub x}Al{sub 1-x}Sb are determined in a wide composition range (0 < x < 0.3). The TEM and SEM studies confirm the high structural quality of grown GaAs/AlInSb heterostructures. Hall-effect measurements showed the dependence of the carrier mobility and concentration on the aluminum content in AlInSb layers and allowed preliminary conclusions on scattering mechanisms.

36 MATERIALS SCIENCE↗

Structure–property relations of orthorhombic [(CH{sub 3}){sub 3}NCH{sub 2}COO]{sub 2}(CuCl{sub 2}){sub 3}·2H{sub 2}O

Large single crystals of orthorhombic [(CH{sub 3}){sub 3}NCH{sub 2}COO]{sub 2}(CuCl{sub 2}){sub 3}·2H{sub 2}O with dimensions up to 40×40×30 mm{sup 3} were grown from aqueous solutions. The elastic and piezoelastic coefficients were derived from ultrasonic resonance frequencies and their shifts upon variation of pressure, respectively, using the plate-resonance technique. Additionally, the coefficients of thermal expansion were determined between 95 K and 305 K by dilatometry. The elastic behaviour at ambient conditions is dominated by the 2-dimensional network of strong hydrogen bonds within the (001) plane leading to a corresponding pseudo-tetragonal anisotropy of the longitudinal elastic stiffness. The variation of elastic properties with pressure, however, as well as the thermal expansion shows strong deviations from the pseudo-tetragonal symmetry. These deviations are probably correlated with tilts of the elongated tri-nuclear betaine–CuCl{sub 2}–water complexes. Neither the thermal expansion nor the specific heat capacity gives any hint on a phase transition in the investigated temperature range. - Graphical abstract: Single crystal of orthorhombic [(CH{sub 3}){sub 3}NCH{sub 2}COO]{sub 2}(CuCl{sub 2}){sub 3}·2H{sub 2}O. - Highlights: • Large single crystals (40 ×40 ×30 mm{sup 3}) of [(CH{sub 3}){sub 3}NCH{sub 2}COO]{sub 2}(CuCl{sub 2}){sub 3}·2H{sub 2}O were grown. • The elastic and piezoelastic coefficients were derived from ultrasonic resonance frequencies. • Thermal expansion (95 K–305 K) and heat capacity (113 K–323 K) were determined. • The orthorhombic structure shows pseudo-tetragonal elastic anisotropy at ambient conditions. • The crystal structure is stable in the investigated range (1–1600 bar, 95–303 K)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural properties of Bi{sub 2}Te{sub 3} and Bi{sub 2}Se{sub 3} topological insulators grown by molecular beam epitaxy on GaAs(001) substrates

Thin films of Bi{sub 2}Te{sub 3} and Bi{sub 2}Se{sub 3} have been grown on deoxidized GaAs(001) substrates using molecular beam epitaxy. Cross-sectional transmission electron microscopy established the highly parallel nature of the Te(Se)-Bi-Te(Se)-Bi-Te(Se) quintuple layers deposited on the slightly wavy GaAs substrate surface and the different crystal symmetries of the two materials. Raman mapping confirmed the presence of the strong characteristic peaks reported previously for these materials in bulk form. The overall quality of these films reveals the potential of combining topological insulators with ferromagnetic semiconductors for future applications.

36 MATERIALS SCIENCE↗

Effect of cesium assistance on the electrical and structural properties of indium tin oxide films grown by magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by cesium (Cs)-assisted dc magnetron sputtering in an attempt to achieve a high performance at low temperatures. The films were deposited on SiO{sub 2}/Si wafer and glass (Eagle 2000) substrates at a substrate temperature of 100 degree sign C with a Cs vapor flow during the deposition process. The ITO thin films deposited in the presence of Cs vapor showed better crystallinity than the control films grown under normal Ar/O{sub 2} plasma conditions. The resistivity of the films with the Cs assistance was lower than that of the control films. The lowest resistivity of 6.2x10{sup -4} {Omega} cm, which is {approx}20% lower than that of the control sample, was obtained without any postdeposition thermal annealing. The surface roughness increased slightly when Cs vapor was added. The optical transmittance was >80% at wavelengths ranging from 380 to 700 nm.

36 MATERIALS SCIENCE↗

Structural Properties of Ditechnetium Heptoxide, Tc{sub 2}O{sub 7}

Group 7 elements form unique binary oxides with the stoichiometry M{sub 2}O{sub 7}. The heptoxides of manganese and technetium crystallize as molecular solids while rhenium forms an extended solid with mixed valances, 4 and 6. Unlike manganese and rhenium heptoxides which are used in the chemical industry technetium heptoxide has found very few applications due to its radioactive nature; it has been primarily use as a chemical precursor. While both of the molecular solids, Mn{sub 2}O{sub 7}{sup 3} and Tc{sub 2}O{sub 7}{sup 4} can be described by two corner-sharing MO{sub 4} tetrahedron. The most distinctive difference is that the manganese's compound has a metal-oxygen-metal bond angle of 120.7 deg. while the technetium species is 180 deg.. Additionally, Tc{sub 2}O{sub 7} has the largest molar volume of the heptoxides which suggest that it will be more susceptible to external stimuli of pressure and temperature than the others heptoxides. A pressure induced twisting has been predicted by Fang et al. Anomalous behavior is seen in the c-axis where below 2 GPa the Van der Waals interactions between the Tc{sub 2}O{sub 7} molecules is over come and compression is observed but at higher pressures the twisted distortion forces the lattice to expand. The terminology diagonal-double tetrahedrons (DDTs) is introduced to discuss the molecules of Tc{sub 2}O{sub 7}. The rigid nature of the DDTs has been attributed to the cause of this twisted distortion mechanism. Recently, the solid state and gas phase behavior of technetium heptoxide was revisited by Childs et al. in light of {sup 99}Tc being an important dose contributor in the Hanford waste and vitrification being proposed for immobilization of nuclear waste. Technetium heptoxide is one of the proposed volatilized species of technetium found in the vitrification process. In this study the crystal structure of Tc{sub 2}O{sub 7} was reported at 100 K and compared to the structure first determined by Krebs at room temperature. Inspection of the metal-oxygen distances revealed the 100 K structure had longer bond lengths for the bridging oxygen than at high temperature. It is suggested that transverse thermal vibrational modes can be used to explain this negative thermal expansion behavior. This describes the average bond length of a central atom (i.e. the bridging oxygen atom) being measured as shorter at higher temperatures due to the larger thermal motion. Diffraction methods that measure the long range average structure are susceptible to observing this shorter average length as opposed to the true bond length, atom position at oscillation node that a method like Pair-Distribution Functional PDF Analysis would yield. In the case of Tc{sub 2}O{sub 7}, the magnitude of the transverse thermal vibrational mode is at the limit of being detectable by SCXRD and likely not observable by PDF analysis. Here we report the preliminary results of our study on the nature of the thermal expansion behavior of Tc{sub 2}O{sub 7}. The transverse thermal vibration mode compression mechanism is considered and compared to the pressure induced twisted distortion mechanism predicted at high pressure. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Radiative-capture cross sections for the La 139 ( n , γ ) reaction using thermal neutrons and structural properties of La 140

A set of prompt partial γ-ray production cross sections from thermal neutron capture were measured for the La 139 ( n , γ ) reaction using a guided beam of subthermal (thermal and cold) neutrons incident on a nat La 2 O 3 target at the Prompt Gamma Activation Analysis facility of the Budapest Research Reactor. Absolute La 140 cross sections were determined relative to the well-known comparator 35 Cl(n,γ) cross sections from the irradiation of a stoichiometric nat LaCl 3 sample. Here, the total cross section for radiative thermal neutron capture on La 139 from the sum of experimentally measured cross sections observed to directly feed the La 140 ground state was determined to be $σ$ $^{expt}_{0}$ = 8.58 (50) b.

139La(n, γ), E=thermal and cold↗

Interfacial and structural properties of sputtered HfO{sub 2} layers

Magnetron sputtered HfO{sub 2} layers formed on a heated Si substrate were studied by spectroscopic ellipsometer (SE), x-ray diffraction (XRD), Fourier transform infrared (FTIR), and x-ray photoelectron spectroscopy (XPS) depth profiling techniques. The results show that the formation of a SiO{sub x} suboxide layer at the HfO{sub 2}/Si interface is unavoidable. The HfO{sub 2} thickness and suboxide formation are highly affected by the growth parameters such as sputtering power, O{sub 2}/Ar gas ratio during sputtering, sputtering time, and substrate temperature. XRD spectra show that the deposited film has (111) monoclinic phase of HfO{sub 2}, which is also supported by FTIR spectra. The atomic concentration and chemical environment of Si, Hf, and O have been measured as a function of depth starting from the surface of the sample by XPS technique. It shows that HfO{sub 2} layers of a few nanometers are formed at the top surface. Below this thin layer, Si-Si bonds are detected just before the Si suboxide layer, and then the Si substrate is reached during the depth profiling by XPS. It is clearly understood that the highly reactive sputtered Hf atoms consume some of the oxygen atoms from the underlying SiO{sub 2} to form HfO{sub 2}, leaving Si-Si bonds behind.

36 MATERIALS SCIENCE↗