Search NASA⌕ Search

SEARCH · Search NASA

Results for “Supersonic flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Transition Induced by an Egg-Crate Roughness on a Flat Plate in Supersonic Flow

Measurements were made in the wake of a roughness patch with a hot wire to determine mode shapes and frequencies of the dominant instabilities. The egg-crate roughness pattern is an analytic function described by a sinusoidal equation, similar to arrays of discrete elements that are positioned in a spanwise and streamwise grid, which were considered in previous computations. This is an intermediate configuration toward understanding the underlying physics of pseudorandom distributed roughness. At a freestream unit Reynolds number of10.8×106/m, the boundary layer did not transition within the measurement region. The largest amplitude boundary layer instability was centered near 53 kHz and appeared to be similar to an antisymmetric mode centered behind the region downstream of all of the peaks in the egg-crate roughness. This mode was similar to a mode found to have the highest N factor in previous computational studies. At a freestream unit Reynolds number of12.6×106/m, the boundary layer transitioned to turbulence. The dominant instability was centered near 74 kHz and grew linearly before saturating and breaking down. The mode shape of the 74-kHz mode was again an antisymmetric mode centered behind all of the peaks in the egg-crate roughness.

Amanda Chou↗
NASA NTRS1994

Design and operation of a supersonic annular flow facility

Supersonic annular flow passages exist in propulsion applications that include dual combustion ramjet engines where a supersonic annular flow (the outer flow) mixes with a sonic (or supersonic) gas generator flow (the inner flow) in the shock expansion zone downstream of the gas generator nozzle exit. Other engine designs include components in the form of annular ducts whose cross-sectional area varies in the streamwise flow direction. In some of these configurations, it is necessary to support the outer shroud (cowl) by means of struts positioned between the cowl and centerbody. To investigate the distorting influence of these struts on the local flow structure, it is first necessary to ensure that the intrinsic flow without struts is free of wave reflections and the effects of upstream disturbances. It is also necessary to demonstrate that the intrinsic flow exhibits the characteristics of a well-defined turbulent boundary layer flow, so that changes in the local flow structure induced by the presence of struts can be interpreted properly. The purpose of this Note is to demonstrate that a supersonic flow facility that meets these objectives has been developed.

Williams, K. E.↗
NASA NTRS1987

Numerical simulation of three-dimensional supersonic inlet flow fields

Supersonic inlet flows with mixed external-internal compressions of an axisymmetric inlet model were computed using a combined implicit-explicit (Beam-Warming-Steger/MacCormack) method for solving the three-dimensional unsteady, compressible Navier-Stokes equations in conservation form. Numerical calculations were made of various flows typically found in supersonic inlets such as shock-wave intersections, flow spillage around the cowl lip, shock-wave/boundary-layer interactions, control of shock-induced flow separation by means of boundary layer bleed, internal normal (terminal) shocks, and the effects of flow incidence. Computed results were compared with available wind tunnel data.

Kawamura, T.↗
NASA NTRS1972

Influence of contraction section shape and inlet flow direction on supersonic nozzle flow and performance.

Wall static pressure measurements and performance parameters are presented for axisymmetric supersonic nozzles with relatively steep convergent sections and comparatively small radius-of-curvature throats. The nozzle walls were essentially adiabatic. These results are compared with those obtained in other nozzles tested previously to appraise the influence of contraction shape on performance. Both the flow coefficient and the thrust were less than the corresponding values for one-dimensional, isentropic, plane flow for both the axial and radial inflow nozzles considered, but the specific impulse, the most important performance parameter, was found to be relatively unchanged. The thrust decrement for the axial inflow nozzles was established primarily by the shape of the contraction section, and could be estimated reasonably well from a conical sink flow consideration. The radial inflow nozzle has a potential advantage from a cooling point of view if used in a rocket engine.

Back, L. H.↗
NASA NTRS1975

Introduction to the aerodynamics of flight

General concepts of the aerodynamics of flight are discussed. Topics considered include: the atmosphere; fluid flow; subsonic flow effects; transonic flow; supersonic flow; aircraft performance; and stability and control.

Talay, T. A.↗
NASA NTRS1984

Metric-discontinuous zonal grid calculations using the Osher scheme

Computations on zonal grids - in particular, grids with metric discontinuities resulting from the interspersion of highly clustered regions with coarse regions - are possible using a fully conservative form of the Osher upwind scheme. These zonal grids can result from an abrupt clustering of points near solution discontinuities or near other flow features that require improved resolution. The zonal approach is shown to capture shocks with almost 'shock-fitting' quality but with minimal effort. Results for inviscid flow, including quasi-one-dimensional nozzle flow, supersonic flow over a cylinder, and blast-wave diffraction by a ramp, are presented. These calculations demonstrate the powerful capabilities of the Osher scheme used in conjunction with zonal grids in simulating flow fields with complex shock patterns.

Rai, M. M.↗
NASA NTRS1990

The pdf approach to turbulent flow

This paper provides a detailed discussion of the theory and application of probability density function (pdf) methods, which provide a complete statistical description of turbulent flow fields at a single point or a finite number of points. The basic laws governing the flow of Newtonian fluids are set up in the Eulerian and the Lagrangian frame, and the exact and linear equations for the characteristic functionals in those frames are discussed. Pdf equations in both frames are derived as Fourier transforms of the equations of the characteristic functions. Possible formulations for the nonclosed terms in the pdf equation are discussed, their properties are assessed, and closure modes for the molecular-transport and the fluctuating pressure-gradient terms are reviewed. The application of pdf methods to turbulent combustion flows, supersonic flows, and the interaction of turbulence with shock waves is discussed.

Kollmann, W.↗
NASA NTRS1991

Development of a quiet supersonic wind tunnel with a cryogenic adaptive nozzle

The main objectives of this work is to demonstrate the potential of a cryogenic adaptive nozzle to generate quiet (low disturbance) supersonic flow. A drive system was researched for the Fluid Mechanics Laboratory (FML) Laminar Flow Supersonic Wind Tunnel (LFSWT) using a pilot tunnel. A supportive effort for ongoing Proof of Concept (PoC) research leading to the design of critical components of the LFSWT was maintained. The state-of-the-art in quiet supersonic wind tunnel design was investigated. A supersonic research capability was developed within the FML.

Wolf, Stephen D.↗
NASA NTRS1988

CARS measurements of temperature and species number density in supersonic combusting flow

A supersonic combustion burner has been probed by coherent anti-Stokes Raman Spectroscopy and the results compared with computational fluid dynamics. Simultaneous measurement of temperature, nitrogen number density and oxygen number density have been acquired throughout the external combustion region. Preliminary calculations have been made on this system to estimate the burner performance. Comparisons of these techniques are included.

Antcliff, Richard R.↗