Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Analysis and test evaluation of the dynamic response and stability of three advanced turboprop models at low forward speed

Results of wind tunnel tests at low forward speed for blade dynamic response and stability of three 62.2 cm (24.5 in) diameter models of the Prop-Fan, advanced turboprop, are presented. Measurements of dynamic response were made with the rotors mounted on an isolated nacelle, with varying tilt for nonuniform inflow. Low speed stall flutter tests were conducted at Mach numbers from 0.0 to 0.35. Measurements are compared to Eigen-solution flutter boundaries. Calculated 1P stress response agrees favorably with experiment. Predicted stall flutter boundaries correlate well with measured high stress regions. Stall flutter is significantly reduced by increased blade sweep. Susceptibility to stall flutter decreases rapidly with forward speed.

Smith, Arthur F.↗
NASA NTRS1986

Space Telescope Antenna Pointing System analysis and test

The Space Telescope (ST), carrying five astronomy instruments, is a long-life spacecraft designed to achieve and maintain ultrafine stabilization jitter performance. The rms jitter specification for pointing performance is 7 marcsec (1sigma) during periods of scientific observation. Spacecraft attitude control is achieved by onboard computer processing of attitude and rate sensor data to generate reaction-wheel torque commands. The ST Antenna Pointing System is used to position a high-gain antenna for relaying science and engineering data from the spacecraft to the ground station.

Dodder, R.↗
NASA NTRS1987

Thermal design, analysis and testing of the Halogen Occultation Experiment

This paper briefly introduces the Halogen Occultation Experiment (HALOE) and describes the thermal requirements in some detail. The thermal design of the HALOE is described, together with the design process and the analytical techniques used to arrive at this design. The flight hardware has undergone environmental testing in a thermal vacuum chamber to validate the thermal design. The HALOE is a unique problem in thermal control due to its variable solar loading, its extremely sensitive optical components and the high degree of pointing accuracy required. This paper describes the flight hardware, the design process and its verification.

Foss, Richard A.↗
NASA NTRS1988

Evaluate the application of modal test and analysis processes to structural fault detection in MSFC-STS project elements

The Space Transportation System (STS) is a very complex and expensive flight system which is intended to carry payloads into low Earth orbit and return. A catastrophic failure of the STS (such as experienced in the 51-L incident) results in the loss of both human life as well as very expensive hardware. One impact of this incident was to reaffirm the need to do everything possible to insure the integrity and reliability of the STS is sufficient to produce a safe flight. One means of achieving this goal is to expand the number of inspection technologies available for use on the STS. The purpose was to begin to evaluate the possible use of assessing the structural integrity of STS components for which Marshall Space Flight Center (MSFC) has responsibility. This entailed reviewing the available literature and determining a low-level experimental program which could be performed by MSFC and would help establish the feasibility of using this technology for structural fault detection.

Springer, William T.↗
NASA NTRS1989

Design, analysis, and testing of a hybrid scale structural dynamic model of a Space Station

The impracticality of testing the fully-assembled on-orbit configurations of future large erectable space platforms fosters an increased reliance on other means for verifying predicted structural dynamic performance. One option is scale modeling. This paper discusses the design of a hybrid scale dynamic test model of the Freedom Space Station and its associated suspension system. Hybrid scaling laws are reviewed, followed by scale factor trades, component design examples, and an analytical evaluation of the overall model fidelity. Component and subassembly test results from a six-bay hybrid scale model truss are presented. Potential interactions of gravity and the suspension system with the free-free dynamics of the scale model are investigated. Suspension system design parameters, such as the number, location, mass, and stiffness of the suspension devices are traded to minimize undesirable interactions and form the basis for an overall suspension system concept for the scale model.

Gronet, Marc J.↗
NASA NTRS1989

Analysis and test of insulated components for rotary engine

The direct-injection stratified-charge (DISC) rotary engine, while attractive for aviation applications due to its light weight, multifuel capability, and potentially low fuel consumption, has until now required a bulky and heavy liquid-cooling system. NASA-Lewis has undertaken the development of a cooling system-obviating, thermodynamically superior adiabatic rotary engine employing state-of-the-art thermal barrier coatings to thermally insulate engine components. The thermal barrier coating material for the cast aluminum, stainless steel, and ductile cast iron components was plasma-sprayed zirconia. DISC engine tests indicate effective thermal barrier-based heat loss reduction, but call for superior coefficient-of-thermal-expansion matching of materials and better tribological properties in the coatings used.

Badgley, Patrick R.↗
NASA NTRS1989

Analysis and test of a 16-foot radial rib reflector developmental model

Analytical and experimental modal tests were performed to determine the vibrational characteristics of a 16-foot diameter radial rib reflector model. Single rib analyses and experimental tests provided preliminary information relating to the reflector. A finite element model predicted mode shapes and frequencies of the reflector. The analyses correlated well with the experimental tests, verifying the modeling method used. The results indicate that five related, characteristic mode shapes form a group. The frequencies of the modes are determined by the relative phase of the radial ribs.

Birchenough, Shawn A.↗
NASA NTRS1989

Lightweight composite mirror analysis and testing

The Jet Propulsion Laboratory InterDisciplinary Model for precision composite structures is described along with the HAVOC composite computer code used to study laminate mirror facesheets. The composite mirror panel thermal behavior is described in addition to structural and optical characteristics. Environmental mirror performance testing and performance test/prediction correlation are covered.

Helms, R. G.↗
NASA NTRS1986

Multiperspective analysis and testing of expert systems

The paper describes a technique which the author developed for testing expert systems. The technique, which he calls multiperspective testing, can be applied during both the knowledge engineering phase and the acceptance testing phase of developing an exppert system. The first step in multiperspective testing is to define a group of performance measures ('perspectives') that focus on the behavior of the knowledge base. For each such measure, the results of testing are summarized in four scores, which the author calls 'expansion,' 'detection,' 'discrimination,' and 'comprehension.' These scores have the advantage of providing more specific information about how the knowledge base should be updated or corrected.

Bollinger, Terry B.↗
NASA NTRS1991

Laboratory test and acoustic analysis of cabin treatment for propfan test assessment aircraft

An aircraft cabin acoustic enclosure, built in support of the Propfan Test Assessment (PTA) program, is described. Helmholtz resonators were attached to the cabin trim panels to increase the sidewall transmission loss (TL). Resonators (448) were located between the trim panels and fuselage shell. In addition, 152 resonators were placed between the enclosure and aircraft floors. The 600 resonators were each tuned to a 235 Hz resonance frequency. After flight testing on the PTA aircraft, the enclosure was tested in the Kelly Johnson R and D Center Acoustics Lab. Laboratory noise reduction (NR) test results are discussed. The enclosure was placed in a Gulfstream 2 fuselage section. Broadband (138 dB overall SPL) and tonal (149 dB overall SPL) excitations were used in the lab. Tonal excitation simulated the propfan flight test excitation. The fundamental tone was stepped in 2 Hz intervals from 225 through 245 Hz. The resonators increase the NR of the cabin walls around the resonance frequency of the resonator array. The effects of flanking, sidewall absorption, cabin adsorption, resonator loading of trim panels, and panel vibrations are presented. Increases in NR of up to 11 dB were measured.

Kuntz, H. L.↗
NASA NTRS1991

Analysis and testing of a space crane articulating joint testbed

The topics are presented in viewgraph form and include: space crane concept with mobile base; mechanical versus structural articulating joint; articulating joint test bed and reference truss; static and dynamic characterization completed for space crane reference truss configuration; improved linear actuators reduce articulating joint test bed backlash; 1-DOF space crane slew maneuver; boom 2 tip transient response finite element dynamic model; boom 2 tip transient response shear-corrected component modes torque driver profile; peak root member force vs. slew time torque driver profile; and open loop control of space crane motion.

Thomas R Sutter↗
NASA NTRS1990

Design, analysis, and testing of a reusable wingbox for ballistic evaluation of composite structures

Future fighter aircraft will continue to be subjected to severe mechanical loading and ballistic impact. In the past aircraft primary wing structure was constructed predominantly with aluminum, but with increasing aircraft performance the need for more structurally efficient materials is necessary. In an attempt to achieve structural efficiency requirements, aircraft designers have begun using an increasing amount of composite materials. Composite materials were indicated to have a low level of ballistic tolerance in some applications. Composite materials possess the characteristic of structural tailoring, which was utilized to demonstrate that survivability can be designed into a structure. The combat flight environment subjects fighter aircraft wing structures to the effects of combined loading during ballistic impact. These loads were previously demonstrated independently, i.e., the application of structural load, hydrodynamic ram damage, and the effects of airflow. The objective was to design a reusable test fixture for the ballistic evaluation of advanced composite structures under all the effects of combined loading. The fixture that was developed provides a test bed that can completely simulate the flight environment of a generic fighter aircraft wing, but can be used for an indefinite number and variety of tests. It is intended that this fixture will provide a standardized method of ballistically evaluating an advanced composite primary wing structure. This fixture will be used to accomplish the development of designs and/or advanced concepts that lead to a survivable composite wing structure.

Baron, W. G.↗
NASA NTRS1992

Analysis and testing of propellant feed system priming process

This paper presents the analytical and the experimental results pertaining to the priming process of the propellant feed system with initial line pressures starting from 0 psia and greater. The analytical methods employ the method of characteristics to solve for the one-dimensional liquid transients in the liquid-full segments and the lumped inertia technique to model the dynamics of the partially filled segments or the two-phase segments. The advantages of these methods are (1) fluid compressibility and piping flexibility are accounted for in the solution; and (2) the characteristics method can be used in the solution of a complex system. The analytical results were compared with test results. Excellent correlation was obtained between predictions and test results verifying the essential aspects of the analytical modeling techniques and providing the foundation for analyzing a complicated network system.

Lin, T. Y.↗
NASA NTRS1992

Results from the testing and analysis of LDEF batteries

Batteries were used on the Long Duration Exposure Facility (LDEF) to provide power to both the active experiments and the experiment support equipment such as the Experiment Initiative System, Experiment Power and Data System (data acquisition system), and the Environment Exposure Control Canisters. Three different types of batteries were used: lithium sulfur dioxide (LiSO2), lithium carbon monofluoride (LiCF), and nickel cadmium (NiCd). A total of 92 LiSO2, 10 LiCF, and 1 NiCd batteries were flown on the LDEF. In addition, approximately 20 LiSO2 batteries were kept in cold storage at NASA LaRC. The various investigations and post-flight analyses of the flight and control batteries are reviewed. The primary objectives of these studies was to identify degradation modes (if any) of the batteries and to provide information useful to future spacecraft missions. Systems SIG involvement in the post-flight evaluation of LDEF batteries was two-fold: (1) to fund SAFT (original manufacturer of the LiSO2 batteries) to perform characterization of 13 LiSO2 batteries (10 flight and 3 control batteries); and (2) to integrate investigator results.

Spear, Steve↗
NASA NTRS1992

Results from testing and analysis of solar cells flown on LDEF

A brief discussion of the solar cell experiments flown on the Long Duration Exposure Facility (LDEF) is provided. The information presented is a collation of results published by the various experimenters. This process of collation and documentation is an ongoing Systems Special Investigation Group (SIG) effort. There are four LEO environments, operating individually and/or synergistically, that cause performance loss in solar cells: meteoroid and space debris, atomic oxygen, ultraviolet radiation, and charged particle radiation. In addition, the effects of contamination caused by outgassing of materials used on the specific spacecraft play a role in decreasing the light being transmitted through the coverglass and adhesive to the solar cell. From the results presented on the solar cells aboard LDEF, the most extensive degradation of the solar cells came from impacts and the resulting cratering. The extent of the damage to the solar cells was largely dependent upon the size and energy of the meteoroids or space debris. The other cause of degradation was reduced light reaching the solar cell. This was caused by contamination, UV degradation of coverglass adhesive, and/or atomic oxygen/UV degradation of antireflection coatings.

Dursch, Harry↗
NASA NTRS1992

System related testing and analysis of FRECOPA

Results from the French Cooperative Payload (FRECOPA) system analysis are presented. It was one of the numerous experiments which were flown on the Long Duration Exposure Facility (LDEF) satellite. In our flight configuration (LEO orbit, trailing edge), the environment was a better vacuum than the leading edge, with many thermal cycles (32000) and a large amount of UV radiation (11100 equivalent sun hours). Also, the satellite was mainly bombarded by micro-particles. It saw a low atomic flux and minor doses of protons and electrons.

Durin, Christian↗