Search NASA⌕ Search

SEARCH · Search NASA

Results for “Two Phase Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Critical flow and pressure ratio data for LOX flowing through nozzles

LOX and LN2 data for two-phase critical flow through nozzles were acquired with precision control. The principal measured parameters were inlet conditions, critical flow rate and critical flow pressure ratio. It is conclusively demonstrated that the principle of corresponding states can be applied to two-phase choked flow through nozzles. It is also shown that the proper normalizing parameters are developed, and that current theories can provide an adequate means for extrapolating data to other fluids.

Hendricks, R. C.↗

Critical flow and pressure ratio data for LOX flowing through nozzles

LOX and LN2 data for two-phase critical flow through nozzles have been acquired with precision control. The principal measured parameters were inlet conditions, critical flow rate and critical flow pressure ratio. The data conclusively demonstrate that the principle of corresponding states can be applied to two-phase choked flow through nozzles. These data also demonstrate that the proper normalizing parameters have been developed and current theories can provide an adequate means for extrapolating to other fluids.

Hendricks, R. C.↗

Two-Phase Quality/Flow Meter

A quality and/or flow meter employs a capacitance probe assembly for measuring the dielectric constant of flow stream, particularly a two-phase flow stream including liquid and gas components.ne dielectric constant of the flow stream varies depending upon the volume ratios of its liquid and gas components, and capacitance measurements can therefore be employed to calculate the quality of the flow, which is defined as the volume ratio of liquid in the flow to the total volume ratio of gas and liquid in the flow. By using two spaced capacitance sensors, and cross-correlating the time varying capacitance values of each, the velocity of the flow stream can also be determined. A microcontroller-based processing circuit is employed to measure the capacitance of the probe sensors.The circuit employs high speed timer and counter circuits to provide a high resolution measurement of the time interval required to charge each capacitor in the probe assembly. In this manner, a high resolution, noise resistant, digital representation of each of capacitance value is obtained without the need for a high resolution A/D converter, or a high frequency oscillator circuit. One embodiment of the probe assembly employs a capacitor with two ground plates which provide symmetry to insure that accurate measurements are made thereby.

Moerk, J. Steven↗

Dual Cryogenic Capacitive Density Sensor

A dual cryogenic capacitive density sensor has been developed. The device contains capacitive sensors that monitor two-phase cryogenic flow density to within 1% accuracy, which, if temperature were known, could be used to determine the ratio of liquid to gas in the line. Two of these density sensors, located a known distance apart, comprise the sensor, providing some information on the velocity of the flow. This sensor was constructed as a proposed mass flowmeter with high data acquisition rates. Without moving parts, this device is capable of detecting the density change within a two-phase cryogenic flow more than 100 times a second. Detection is enabled by a series of two sets of five parallel plates with stainless steel, cryogenically rated tubing. The parallel plates form the two capacitive sensors, which are measured by electrically isolated digital electronics. These capacitors monitor the dielectric of the flow essentially the density of the flow and can be used to determine (along with temperature) the ratio of cryogenic liquid to gas. Combining this information with the velocity of the flow can, with care, be used to approximate the total two-phase mass flow. The sensor can be operated at moderately high pressures and can be lowered into a cryogenic bath. The electronics have been substantially improved over the older sensors, incorporating a better microprocessor, elaborate ground loop protection and noise limiting circuitry, and reduced temperature sensitivity. At the time of this writing, this design has been bench tested at room temperature, but actual cryogenic tests are pending

Youngquist, Robert↗

Summary of nozzle-exhaust plume flowfield analyses performed in support of space shuttle applications

Results are summarized of various analyses of the exhaust plumes of the space shuttle. Specific topics discussed included: the development of the two-phase plume flow field model, including finite rate chemistry and free molecular effects; analyses of exhaust plume simulation studies; verification of the analytical two-phase plume flow field model; and complete documentation of the two-phase plume computer code.

Smith, S. D.↗

Oxygen rich gas generator design and performance analysis

The present oxygen-rich combustion research investigates oxygen gas generator concepts. The theoretical and modeling aspects of a selected concept are presented, together with a refined concept resulting from the findings of the study. This investigation examined a counter-flow gas generator design for O2/H2 mass ratios of 100-200, featuring a near-stoichiometric combustion zone followed by downstream mixing. The critical technologies required to develop a performance model are analyzed and include the following: (1) oxygen flow boiling; (2) two-phase oxygen flow heat transfer; (3) film-cooling in the combustion zone; (4) oxygen-rich combustion with hydrogen; and (5) mixing and dilution.

Gloyer, P. W.↗

Deepak Condenser Model (DeCoM)

Development of the DeCoM comes from the requirement of analyzing the performance of a condenser. A component of a loop heat pipe (LHP), the condenser, is interfaced with the radiator in order to reject heat. DeCoM simulates the condenser, with certain input parameters. Systems Improved Numerical Differencing Analyzer (SINDA), a thermal analysis software, calculates the adjoining component temperatures, based on the DeCoM parameters and interface temperatures to the radiator. Application of DeCoM is (at the time of this reporting) restricted to small-scale analysis, without the need for in-depth LHP component integrations. To efficiently develop a model to simulate the LHP condenser, DeCoM was developed to meet this purpose with least complexity. DeCoM is a single-condenser, single-pass simulator for analyzing its behavior. The analysis is done based on the interactions between condenser fluid, the wall, and the interface between the wall and the radiator. DeCoM is based on conservation of energy, two-phase equations, and flow equations. For two-phase, the Lockhart- Martinelli correlation has been used in order to calculate the convection value between fluid and wall. Software such as SINDA (for thermal analysis analysis) and Thermal Desktop (for modeling) are required. DeCoM also includes the ability to implement a condenser into a thermal model with the capability of understanding the code process and being edited to user-specific needs. DeCoM requires no license, and is an open-source code. Advantages to DeCoM include time dependency, reliability, and the ability for the user to view the code process and edit to their needs.

Patel, Deepak↗

Combustor Emissions Modeling of Sustainable Fuels for Commercial Supersonics Technology

An overview is provided of a CFD assessment with Jet-A replacement fuels and advanced fuel blends to assess fuel impacts on NOx emissions and flame structure in an axially-staged combustor for NASA’s Commercial Supersonic Transport (CST) program. The National Combustor Code (OpenNCC) was used to perform two-phase reacting flow computations with two replacement fuels for Jet-A, and various blending ratios of ‘average’ Jet-A (A2) and GEVO-ATJ (C1), for UTRC’s Axially Controlled Stoichiometry (ACS) combustor at CST cruise conditions. The predicted flame structures in the ACS combustor with for the replacement fuels, and for three different blending ratios of A2 and C1 fuel were very similar to each other. The predicted NOx emissions for the two replacement fuels, and three blending ratios of A2 and C1 were within 15% of the experimentally measured NOx emissions for 100% A2 fuel.

Gas Turbine Combustion↗

Flow Boiling and Condensation Experiment (FBCE): Summary of Findings for Flow Boiling based on Completed ISS Experiments

Since 2011, researchers from Purdue University and NASA Glenn Research Center (GRC) have been collaborating to investigate the effects of gravity on several aspects of flow boiling and flow condensation. This massive research endeavor, termed the Flow Boiling and Condensation Experiment (FBCE), has culminated in development of NASA’s largest and most complex facility for investigation of two-phase fluid physics onboard the ISS. FBCE consists of two separate studies: flow boiling, using the Flow Boiling Module (FBM), and flow condensation, using the Condensation Module for Heat Transfer Measurements (CM-HT); this presentation concerns the FBM portion of FBCE. Fitted with FBM, FBCE was launched to the ISS in August 2021 and experiments were successfully performed starting in February 2022 to amass a large microgravity-flow-boiling database supported by extensive visualization of interfacial behavior using high-speed video. Based on FBCE experiments performed previously in Earth gravity and parabolic flight, along with the new ISS data, several empirical correlations, theoretical models, and CFD models have been developed, enabling the prediction of crucial flow boiling parameters, including heat transfer coefficient and critical heat flux (CHF). These predictive tools, which will be summarized in this presentation, are expected to serve as foundation for design of future space systems involving flow boiling.

Two-phase flow and phase transition↗

Detailed Studies on the Structure and Dynamics of Reacting Dusty Flows at Normal and Microgravity

Two-phase reacting flows are substantially less understood compared to gas phase flows. While extensive work has been done on sprays, less attention has been given to the details of dusty reacting flows. Dusty flows are of particular interest for a wide range of applications. Particles can be present in a gas intentionally or unintentionally, and they can be inert or reacting. Inert particles can be also present in an otherwise reacting gas flow, and that can lead to flame cooling and modification of the extinction limits of a combustible mixture. Reacting solid particles can release substantial amounts of heat upon oxidation, and can be used either for propulsion (e.g. Al, B, Mg) or power generation (coal). Furthermore, accidents can occur when a reacting dust accumulates in air and which, in the presence of an ignition source, can cause explosion. Such explosions can occur during lumber milling, in grain elevators, and in mine galleries.

Egolfopoulos, Fokion N.↗

Flow Boiling and Condensation Experiment Overview

A brief overview of the Flow Boiling and Condensation Experiment will be presented at the Technical Interchange Meeting between NASA-GRC Scientists and Engineers and the Korea Aerospace Research Institute (KARI). The presentation describes the development of the FBCE, its constraints, and the on-going testing that had been and continues to be executed onboard of the International Space Station (ISS).

International Space Station↗

Case Study of Using Flocad to Model a Ground Test Station Ln2 Heat Exchanger

This paper presents a case study of using FLOCAD to model the heat transfer and boiling flow behavior of a Liquid Nitrogen (LN2) ground station equipment heat exchanger. The unique aspect of this work is that is one of very few studies documenting the use of FLOCAD in the spacecraft thermal control community. The results of the simulations described herein were used to guide and plan the execution of thermal vacuum testing spacecraft hardware using a ground test heat exchanger such as the one modeled herein. The paper will review the theory of two-phase boiling flow and correlations used by SINDA/FLUINT as well as the terminology and nomenclature used within Thermal Desktop / FLOCAD regarding two-phase boiling flow heat transfer modeling and simulation. Results for using the ground station heat exchanger as a heat sink in a thermal vacuum test set up are shown in order to demonstrate the set-up and execution of a typical FLOCAD model. Results indicate that properly modeling of the two-phase behavior is critical in order to ascertain the time constant associated with the heat exchanger, as well as understanding the temperature distribution across the test equipment and prediction of required LN2 flowrates to be used during testing. The paper is meant to augment the FLOCAD user’s manual and serve as a tutorial for thermal engineers and analysts wishing to learn and apply FLOCAD to industrial problems.

Anderson, Kevin R.↗

Ground Based Studies of Gas-Liquid Flows in Microgravity Using Learjet Trajectories

A 1.27 cm diameter two phase gas-liquid flow experiment has been developed with the NASA Lewis Research Center to study two-phase flows in microgravity. The experiment allows for the measurement of void fraction, pressure drop, film thickness and bubble and wave velocities as well as for high speed photography. Three liquids were used to study the effects of liquid viscosity and surface tension, and flow pattern maps are presented for each. The experimental results are used to develop mechanistically based models to predict void fraction, bubble velocity, pressure drop and flow pattern transitions in microgravity.

Bousman, W. S.↗

Fluid spray simulation with two-fluid nozzles

Two-phase interacting flow inside a two-fluid fuel atomizer was investigated and a correction of aerodynamic and liquid-surface forces with characteristic drop diameter was obtained for liquid-jet breakup in Mach 1 gas flow. Nitrogen gas mass-flux was varied from 6 to 50 g/sq cm sec by using four differently sized two-fluid atomizers with nozzle diameters varyig from 0.32 to 0.56 cm. The correlation was derived by using the acoustic gas velocity, V sub c, as a basic parameter in defining and evaluating the dimensionless product of the Weber (We) and Reynolds (Re) numbers. By using the definition of WeRe, it was found that the ratio of orifice diameter to Sauter mean drop diameter could be correlated with the dimensionless ratio WeRe and the gas to liquid density ratio.

Ingebo, Robert D.↗

Fuel spray simulation with two-fluid nozzles

Two-phase interacting flow inside a two-fluid fuel atomizer was investigated and a correction of aerodynamic and liquid-surface forces with characteristic drop diameter was obtained for liquid-jet breakup in Mach 1 gas flow. Nitrogen gas mass-flux was varied from 6 to 50 g/sq cm sec by using four differently sized two-fluid atomizers with nozzle diameters varying from 0.32 to 0.56 cm. The correlation was derived by using the acoustic gas velocity, V sub c, as a basic parameter in defining and evaluating the dimensionless product of the Weber (We) and Reynolds (Re) numbers. By using the definition of WeRe, it was found that the ratio of orifice diameter to Sauter mean drop diameter could be correlated with the dimensionless ratio WeRe and the gas to liquid density ratio.

Ingebo, Robert D.↗