SEARCH · Search NASA

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Aircraft of the future

Some basic problems connected with attempts to increase the size and capacity of transport aircraft are discussed. According to the square-cubic law, the increase in structural weight is proportional to the third power of the increase in the linear dimensions of the aircraft when geomettric similarity is maintained, while the surface area of the aircraft increases according to the second power. A consequence is that the fraction of useful weight will decrease as aircraft increase in size. However, in flying-wing designs in which the whole load on the wing is proportional to the distribution of lifting forces, the total bending moment on the wing will be sharply reduced, enabling lighter construction. Flying wings may have an ultimate capacity of 3000 passengers.

Yeger, S.↗

NASA NTRS1988

Aerodynamic technology opportunities for a high-speed civil transport

A NASA-sponsored study has undertaken the definition of SST and HST configurations resulting in substantial reductions relative to current technology in takeoff gross weight, sonic boom overpressures, and airport-vicinity propulsion and aerodynamic noise. CFD methods have been applied to vehicle-shaping and laminar boundary layer flow area-maximizing configurational studies. Various planforms and active boundary-layer control methods are considered. Computer-managed wing control surface deflections are identified as substantial contributors to wing aerodynamic load and structural weight reduction, while correcting undesirable aerodynamic-pitching characteristics.

Welge, H. Robert↗

NASA NTRS1989

Impact of small-crack effects on design-life calculations

The potential impact of the observed small-crack-effect in 2024-T3 aluminum alloy on calculated crack-growth lives is described. The significance of the small-crack effect is assessed by comparing lives computed using only large-crack data to those computed using a combined small- and large-crack data base for constant-amplitude (R = -1 and 0) and fighter-wing spectrum loading (FALSTAFF) conditions. Based on the life calculations, the small-crack effect would have no impact on life analyses that assume an initial crack larger than about 0.3 mm; only a small impact on life analyses that assume an initial crack of 0.1 mm; but a large impact on life analyses that assume an initial crack of about 0.01 mm. When small-crack effects are taken into account, fatigue life analyses based solely on crack growth may provide a viable alternative to traditional two-part initiation-plus-crack-growth life analyses.

Phillips, E. P.↗

NASA NTRS1937

Theoretical span loading and moments of tapered wings produced by aileron deflection

The effect of tapered ailerons on linearly tapered wings is theoretically determined. Four different aileron spans are considered for each of three wing aspect ratios and each of four wing taper ratios. The change in lift on one half of the wing, the rolling moment, the additional induced drag, and the yawing moment, due to aileron deflection, are represented by non dimensional coefficients. Similar coefficients are given for the damping and yawing moments, the additional drag, and the change in lift, due to rolling. It was found possible to effect a fairly close agreement between the theoretical and experimental rolling moments by introducing into the theoretical expression for the rolling moment an effective change in angle of attack obtained from an analysis of flap data. The theoretical curves show that the highly tapered wing with long ailerons has a lower ratio of yawing to rolling moment and a lower additional induced drag than wings with less taper.

Pearson, H A↗

NASA NTRS1937

Free-spinning Wind-tunnel Tests of a Low-wing Monoplane with Systemic Changes in Wings and Tails

A series of tests was made at the National Advisory Committee for Aeronautics (NACA) free-spinning tunnel to determine the effect of systematic changes in wing and tail arrangement upon steady-spinning and recovery characteristics of a conventional low-wing monoplane model for a basic loading condition. Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 wing-tail combinations, observations were made of steady spins for four control settings and of recoveries for five control manipulators. The results are presented in the form of charts comparing the spin characteristics. The results showed that, with a poor tail arrangement, wing plan form and tip shape had a considerable effect on the spinning characteristics.

Seidman, Oscar↗

NASA NTRS1939

Experimental Study of Deformation and of Effective Width in Axially Loaded Sheet-stringer Panels

The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

FORMULAS - BUCKLING - KARMAN↗

NASA NTRS1947