Search NASA⌕ Search

SEARCH · Search NASA

Results for “backscatter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Revisiting the Hail Radar Reflectivity–Kinetic Energy Flux Relation by Combining T-Matrix and Discrete Dipole Approximation Calculations to Size Distribution Observations

The retrieval of hail kinetic energy with weather radars or its simulation in numerical models is challenging because of the shape complexity and variable density of hailstones. We combine 3D scans of individual hailstones with measurements of the particle size distributions (PSD) and T-matrix calculations to understand how hail reflectivity Z changes when approximating hailstones as spheroids, as compared to the realistic shapes obtained by 3D scanning technology. Additionally, recent terminal velocity relations are used to compare Z to the hail kinetic energy flux E ˙ . We parameterize the hail backscattering cross sections at L, S, C, and X bands as a function of size between 0.5 and 5.0 cm, matching the range of the observed PSDs. The scattering calculations use the T-matrix method for size parameters below 1.0 and the discrete dipole approximation (DDA) method otherwise. The DDA calculations are done for 48 digital models of realistic hailstones of sizes between 1 and 5 cm. The DDA cross sections are calculated for multiple orientations and averaged assuming a fully random orientation distribution to provide a single value per hailstone. The T-matrix reflectivity assuming solid ice spheres presents negligible differences to DDA results for size parameters below 1.0. Therefore, T matrix was used to fill in the gaps left by the DDA calculations. The results are mapped to the same size bins of the observed PSDs, allowing the calculation of the radar reflectivity. This is then correlated to E ˙ , allowing a potential improvement of past retrieval methods of E ˙ from Z in multiple wavelengths.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Wave-by-Wave Forecasting via Assimilation of Marine Radar Data

Abstract This work describes a phase-resolving wave-forecasting algorithm that is based on the assimilation of marine radar image time series. The algorithm is tested against synthetic data and field observations. The algorithm couples X-band marine radar observations with a phase-resolving wave model that uses the linear mild slope equations for reconstruction of water surface elevations over a large domain of O (km) and a prescribed time window of O (min). The reconstruction also enables wave-by-wave forecasting through forward propagation in space and time. Marine radar image time series provide the input wave observations through a previously given relationship between backscatter intensity and the radial component of the sea surface slope. The algorithm assimilates the wave slope information into the model via a best-fit wave source function at the boundary that minimizes the slope reconstruction error over an annular region at the outer ranges of the radar images. The wave model is then able to propagate the waves across a polar domain to a location of interest at nearer ranges. The constraints on the method for achieving real-time forecasting are identified, and the algorithm is verified against synthetic data and tested using field observations.

Engineering↗
DOE OSTI2025

High-Resolution Sampling of a River Plume Front with Uncrewed Underwater and Aerial Vehicles

Sampling fast-propagating oceanic features is inherently challenging and demands versatile instrumentation and innovative strategies. This paper introduces a novel sampling strategy designed to capture such phenomena, exemplified by a river plume front. Our method revolves around modifying the preprogrammed pathway of an uncrewed underwater vehicle (UUV) to dynamically track and three-dimensionally sample the evolution of the front. To enable the UUV to follow the feature, we adapt the use of a drifting gateway buoy to be positioned and trapped at the front’s convergence zone, allowing underway navigation relative to the buoy. In our demonstration, we showcase the effectiveness of this strategy by successfully conducting over 30 crossings of a river plume front within a 6-h window. The UUV sensors allowed a comprehensive assessment of key front characteristics, including density, velocity, and turbulence. Supplemental drone footage contributed to the overall picture and facilitated the transformation of the dataset into a front-following reference frame. This article provides an in-depth description of the deployment strategy and required postcollection data processing, including frontal crossing detection, the assessment of the frontal orientation from drone footage, and defining the plume bottom boundaries using backscatter intensity contours.

autonomous observations↗
DOE OSTI2020

Assessment of Precipitating Marine Stratocumulus Clouds in the E3SMv1 Atmosphere Model: A Case Study from the ARM MAGIC Field Campaign

This paper presents a process-oriented evaluation of precipitating stratocumulus and its transition to cumulus in version 1 of the Energy Exascale Earth System Model (E3SMv1) using comprehensive case-study observations from a field campaign of the Atmospheric Radiation Measurement program (ARM). The E3SMv1 single-column model (SCM) of the marine boundary layer and its low clouds and precipitation are compared to observations including subcloud drizzle retrievals from a combination of Doppler radar and lidar backscatter measurements. Additionally, the SCM is also compared to a large-eddy simulation (LES) of the same case. The combination of advanced remote sensing observations and LES is a powerful framework to evaluate the physical parameterizations of large-scale models. Given the observed large-scale environment, the E3SMv1 SCM realistically represents the evolution of clouds and boundary layer structure during the stratocumulus-to-cumulus transition. The model well simulates the liquid water path and its diurnal cycle in the stratocumulus period as well as the two-layer vertical thermodynamic structure and lower cloud fraction in the transition period. E3SMv1’s success in simulating the cloud in the stratocumulus period permitted examination of its precipitation processes. Here problems were identified with E3SMv1 producing an unrealistically small subcloud precipitation fraction, an unrealistic double peak in the vertical profiles of precipitation mass, and drizzle that evaporates too close to the surface. Further model diagnostics determined that these unrealistic characteristics resulted from an overly long microphysics time step and an unrealistic parameterization of the precipitation fraction. These results imply that careful consideration of these issues is needed in order to better simulate precipitation processes in marine stratocumulus.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Robustness of helical edge states under edge reconstruction

Abstract The helical edge states of time-reversal invariant two-dimensional topological insulators are protected against backscattering in idealized models. In more realistic scenarios with a shallow confining potential at the sample boundary, additional strongly interacting edge states may arise, that could interfere with the topological protection of edge conduction. We find that interaction effects within the reconstructed edges are well described by the Luttinger liquid model. While interactions between this Luttinger liquid and the helical edge states can in principle give rise to dynamical spin polarization and the breaking of time-reversal symmetry, we demonstrate that random spin-orbit coupling strongly suppresses such dynamical spin polarization, resulting in the persistence of near quantized edge conduction.

John, Niels↗
DOE OSTI2023

Time-dependent probability density function analysis of H-mode transitions

Abstract The first application of time-dependent probability density function (PDF) analysis to the L-H transition in fusion plasmas is presented. PDFs are constructed using Doppler Backscattering data of perpendicular fluctuation velocity, , and turbulence from the edge region of the DIII-D tokamak. These raw time-series data are sliced into millisecond-long sliding time-windows to create PDFs. During the transition, the PDFs develop strong right tails, indicative of turbulence-suppressing localised flows in the plasma edge; such features and other subtle behaviours are explored using novel information geometry techniques. This letter examines the applicability of these techniques to predict L-H transitions and investigate predator-prey self-regulation theories between turbulence and perpendicular velocity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Methods for Continuously Resolving Spectral Shifts in Distributed Optical Fiber Sensors Irradiated to Extreme Neutron Fluence

Optical frequency domain reflectometry (OFDR) is a technique for interrogating distributed optical fiber sensors (DOFS) and involves correlating changes in the Rayleigh backscatter fingerprint for a fiber under test (FUT) with a reference measurement. Recently, under the WIRE-21 experiment sponsored by Nuclear Science User Facilities (NSUF) and performed at the High-Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL), silica optical fibers were irradiated to a fast neutron fluence of 1x10^21 n/cm^2/s at temperatures from 200--400 C. As in the cases of high-temperature and high-strain conditions, such high levels of neutron bombardment result in a highly dynamic RBS that evades analysis with conventional methods. This work describes the further development and application of graphical signal processing techniques applied to OFDR-based distributed optical fiber sensors specifically deployed in in-pile applications. While the signal processing techniques developed in this work are applied to DOFS in nuclear environments, they provide a general framework for the analysis of OFDR measurements and a tangible method to yield higher quality data, without imposing additional hardware requirements.

Sweeney, Dan↗
DOE OSTI2021

Afterpulse correction for micro-pulse lidar to improve middle and upper tropospheric aerosol measurements

Micro-pulse lidar (MPL) measurements have been widely used in atmospheric research over the past few decades. However, the MPL afterpulse noise has a large impact on the MPL aerosol measurement in the middle and upper troposphere, and an effective correction method is still lacking. Here, a new afterpulse correction approach is presented by using measurements with low-level optically thick clouds to act as the lids blocking atmospheric signals beyond the clouds completely. Examples are provided to illustrate the effectiveness of this correction method. Using one-year 2014 MPL measurements at the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site, the impact of the correction on the aerosol measurements is quantified. The relative error (RE, %) of attenuated backscattering ratio (ABR) without the afterpulse correction is 30% and 190% at the height of 1.00 km and 9.00 km (AGL), and the RE is larger for weaker aerosol signals (ABR<2). The RE of linear depolarization ratio (LDR), which is significantly higher than that of ABR for a given aerosol layer, is highly non-linear above 3.00 km, with a value of 300%-900% for weak aerosols (ABR<2) above 3.00 km. Therefore, the afterpulse correction is critical for the middle and upper tropospheric aerosol observations. We demonstrated that our afterpulse correction can provide reasonable particle depolarization ratio (PDR) to properly identify dust aerosols. The newly developed method can be applied to long-term MPL measurements to support aerosol and mixed-phase/ice cloud interaction study at the NSA site.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Improving high temperature resilience of fiber sensor embedded smart components through laser shock peening

This study explores the use of laser shock peening (LSP) to enhance material properties and high-temperature performance of fiber-sensor-fused smart parts fabricated by additive manufacturing (AM) methods. Using embedded fiber sensors as distributed strain gauges, the study demonstrates that LSP can induce compressive strains of up to 130 µε on fiber embedded 1-mm below metal surfaces. The electron backscatter diffraction (EBSD) analysis shows that, with optimized LSP parameters, the metallic matrix undergoes substantial microstructural refinement, resulting in denser structures. Thermal cycling tests showed that the LSP process can increase fiber slippage temperatures by more than 50 °C. This work shows that the LSP process is an effective room-temperature process for enhancing both surface quality and increasing fiber slippage threshold under both thermal and mechanical stress.

Zhong, Shuda [University of Pittsburgh, PA (United↗
DOE OSTI2022

Expanding the range of the resolvable strain from distributed fiber optic sensors using a local adaptive reference approach

Optical frequency domain reflectometry (OFDR) is a spectral measurement technique in which shifts in the local Rayleigh backscatter spectra can be used to perform distributed temperature or strain measurements relative to a reference measurement using ordinary single-mode optical fibers. Here, we demonstrate a data processing methodology for improving the resolvable range of temperature and strain by adaptively varying the reference measurement position by position, based on the time evolution of the local optical intensities and the correlation between the reference and active measurements. These methods nearly double the resolvable range of temperature and strain compared with that achieved using the traditional static reference approach.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Origin and effect of film sub-stoichiometry on ultraviolet, ns-laser damage resistance of hafnia single layers

Understanding the origin of laser damage-prone precursors in high index materials such as hafnia holds the key to the development of laser damage-resistant multilayer dielectric coated optics for high power and energy laser systems. In this study, we investigate the source of sub-stoichiometry, a potent laser damage precursor, in hafnia films produced by an ion beam sputtering (IBS) deposition method and the effect of such defects on the film performance upon ns ultraviolet (UV) laser (8 ns, 355 nm) exposure. Chemical analysis of data obtained via Rutherford backscattering spectroscopy (RBS) suggests that hafnia films deposited at two different planetary locations from the same deposition run exhibit anisotropic and location-dependent stoichiometries. While the oxygen-to-hafnium ratio is at the stoichiometric value of 2 for the hafnia film at the edge location, the ratio is significantly deviated and is 1.7 for that deposited at the planetary center. The sub-stoichiometric hafnia films display a much lower 1-on-1 damage onset at 1.6 ± 0.2 J/cm 2 compared to 2.3 ± 0.2 J/cm 2 in a stoichiometric film. The low damage performance films also have an over three times higher damage density at fluences above initiation. Coupled with Monte Carlo simulations, we reveal that sub-stoichiometry is primarily attributed to preferential removal of oxygen during film deposition by the bombardment of energetic reflected argon neutrals. The resulting oxygen deficiencies create the sub-bandgap states which facilitate the strong laser energy coupling and reduce the resistance to laser-induced damage in the hafnia single layer films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Improving the laser performance of ion beam sputtered dielectric thin films through the suppression of nanoscale defects by employing a xenon sputtering gas

Laser damage-prone precursors in high index materials such as hafnia are believed to be the primary limiter in the performance of dielectric multilayer films to advance ultra-high power and energy laser applications. Removing or suppressing these precursors is the key to fabricating laser damage resistant thin films for the enabling technologies. Early work has revealed that nanobubbles formed by entrapped argon (Ar) working gas in ion beam sputtering (IBS) produced hafnia films are primarily responsible for the onset of laser damage upon exposure to UV, ns-laser pulses. In this study, we demonstrate that the UV ns-laser damage onset of IBS produced hafnia films can be improved to 3.1 +/- 0.2 J/cm 2 by substituting the conventional Ar working gas with xenon (Xe), a nearly 1 J/cm 2 increase from that of the Ar produced hafnia films. In addition to the suppression of the overall point-defect density of the hafnia films, the reduction of the Xe entrapment eliminates the nanobubbles and the generation of plasmas that initiates the laser damage. The defect suppression and its correlation to the increase in laser damage threshold is revealed by the combined analysis of Rutherford backscattering spectroscopy, electron paramagnetic resonance spectroscopy, transmission electron microscopy, and laser damage testing. Monte Carlo simulations suggest a much smaller entrapment of Xe gas by comparison to Ar, which is attributed to the significant difference in the energy of the reflected neutrals (3X) which are likely to be implanted. These results provide an effective process route with a fundamental understanding for producing high laser damage resistant dielectric films for high power and high energy laser applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ground observations of a space laser for the assessment of its in-orbit performance

The wind mission Aeolus of the European Space Agency was a groundbreaking achievement for Earth observation. Between 2018 and 2023, the space-borne lidar instrument ALADIN onboard the Aeolus satellite measured atmospheric wind profiles with global coverage, which contributed to improving the accuracy of numerical weather prediction. The precision of the wind observations, however, declined over the course of the mission due to a progressive loss of the atmospheric backscatter signal. The analysis of the root cause was supported by the Pierre Auger Observatory in Argentina whose fluorescence detector registered the ultraviolet laser pulses emitted from the instrument in space, thereby offering an estimation of the laser energy at the exit of the instrument for several days in 2019, 2020, and 2021. The reconstruction of the laser beam not only allowed for an independent assessment of the Aeolus performance, but also helped to improve the accuracy in the determination of the laser beam’s ground track on single pulse level. The results presented in this paper set a precedent for the monitoring of space lasers by ground-based telescopes and open new possibilities for the calibration of cosmic-ray observatories.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

CROCUS Sodar Measurements of Lower Atmospheric Wind Profiles at Argonne Testbed for Multiscale Observational Science (ATMOS) Site

The Scintec MFAS Sodar (Multiple-Frequency Acoustic Sounder) is an autonomous, ground-based acoustic remote sensing system designed to measure vertical profiles of horizontal wind speed, wind direction, and vertical velocity in the lower atmosphere. The instrument transmits sequences of acoustic pulses and detects the Doppler-shifted sound waves backscattered by small-scale temperature and velocity fluctuations caused by atmospheric turbulence. From these Doppler shifts, the system derives three-dimensional wind vectors by combining radial velocities from multiple beam orientations.The MFAS Sodar operates with a first usable range gate beginning at approximately 30 m above ground level and a configurable vertical resolution of 10 m. Under favorable acoustic conditions, the system provides wind profiles extending up to 600 m above ground level. Measurements are processed into 15-minute averaged profiles containing wind speed, direction, vertical velocity, and diagnostic quantities such as signal-to-noise ratio and echo strength.This dataset was collected at the Argonne Testbed for Multiscale Observational Science (ATMOS) facility in Lemont, Illinois, as part of DOE's CROCUS Urban Integrated Field Laboratory (UIFL) initiative. The purpose of these observations is to characterize the vertical wind structure and boundary-layer evolution across the urban–suburban gradient of the greater Chicago region. In particular, these data are intended to improve understanding of how local meteorology, such as lake-breeze penetration, nocturnal jets, and daytime mixing, varies between the densely built urban core and the suburban periphery. The MFAS observations provide critical context for evaluating high-resolution model simulations and for integrating with complementary lidar, radar, and in-situ meteorological measurements within the broader CROCUS UIFL network.All data are archived in NetCDF (Network Common Data Form) format and include wind and diagnostic parameters. The files can be accessed and analyzed using standard software that supports NetCDF, such as Python (e.g., xarray, netCDF4), MATLAB, R (e.g., ncdf4, raster), or Panoply (NASA’s NetCDF visualization application).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

CROCUS Urban Canyons - Space Science and Engineering Center (SPARC) Doppler lidar data

This is the netCDF format output from the Halo Photonics Streamline XR Doppler lidar that was deployed next to the Space Science and Engineering Center (SPARC) trailer at the University of Illnois-Chicago greenhouse parking lot during CROCUS Urban Canyons. The purpose of collecting this dataset is to provide vertical and horizontal wind profiles for studying the characteristics of turbulence over the urban canyon of Chicago. This data contains the radial velocity, intensity, and backscatter from the vertical profile, range height indicator, and sector scans that were performed over both Intensive Operating Period 1 and 2 of CROCUS Urban Canyons. There are four different types of files: * The Range Height Indicator (RHI) files contain scans that are along a constant azimuth, spanning the entire hemisphere of elevation values above the surface. * The Velocity Azimuth Display (VAD) files contain the raw radial velocity data from the 6-beam, 60 degree scans. * The User1 files contain stacked Plan Position Indicator scans over a 45 degree quadrant over downtown Chicago. * The Stare files contain vertically pointing scans. These are standard netCDF files that can be opened using xarray. The VAD scans can be processed from their raw radial velocities to horizontal wind speeds with the Atmospheric data Community Toolkit (https://arm-doe.github.io/ACT/).

EARTH SCIENCE > ATMOSPHERE > ATMOSPHERIC WINDS↗
DOE OSTI2021

New Fracture Diagnostic Tool for Unconventionals: High-Resolution Distributed Strain Sensing via Rayleigh Frequency Shift during Production in Hydraulic Fracture Test 2

Fiber Optic monitoring in unconventional reservoirs has proven to be an invaluable diagnostic tool for assessing both near-wellbore stimulation effectiveness and to help describe the far-field frac geometries created by hydraulic fracture stimulation. Unfortunately, gaining any detailed qualitative and quantitative understanding of the near-wellbore frac geometry or cluster/stage productivity during production via Fiber Optic (FO) has proven to be more difficult, particularly in wells producing liquids. A new FO diagnostic method, Distributed Strain Sensing based on Rayleigh Frequency Shift (DSS-RFS), first demonstrated for oil and gas applications in the Hydraulic Test Site 2 (HFTS2) provides new insights about the characteristics of near-wellbore-region (NWR) during production. DSS-RFS is different from other FO strain measurements because it relies on accurate measurement of frequency shifts of Rayleigh backscattered spectrum obtained by scanning the fiber with a coherent optical time-domain reflectometer with a range of laser frequencies using a tunable-wavelength laser system. Changes in strain are measured with an extremely high spatial resolution of 20 cm and with high signal-to-noise ratios over long distances. In HFTS2, strain changes for the entire wellbore have been measured twice during scheduled shut-in and reopening operations (February 2020 and September 2020). After removing temperature effects, consistent strain changes have been observed at the location of most perforation clusters. These are caused by near wellbore fracture aperture changes due to pressure increases during shut-in within the near-wellbore fracture network. The strain-change patterns from the DSS-RFS during shut-in correlate very well with the location of clusters and allow for the definition of extending intervals with positive strain signals at each cluster and slightly compressing intervals with negative strain signals between the clusters and in the non stimulated intervals. The locations of the measured positive strain peaks also show good correspondence to DAS acoustic intensity measurements acquired during the stimulation. The geometry and magnitude of the strain changes differ significantly between the two tested completion designs in the same well. During shut in and reopening each cluster exhibit its own strain-change / pressure path. In addition, the September 2020 dataset also revealed the existence of small but measurable strain changes as consequence of pressure decline during production. These strain changes also correlate well with the presence of producing clusters, but the strain-rate signals are opposite to that obtained during shut-in and reopening operations. Although Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/2-21URTC/D021S031R002/2477551/urtec-2021-5408-ms.pdf/1 by Carol Worster on 28 February 2022 URTeC 5408 2 we are still in the early stages of exploring the potential of this novel FO technique, we believe that the highly detailed information contained in the measurement of strain changes using DSS-RFS during production can significantly improve our understanding of near-wellbore hydraulic fracture characteristics and the relationships between stimulation and production from unconventional oil and gas wells.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Deformation and fracture characteristics of zirconium plate produced via ultrasonic additive manufacturing

Abstract The microstructural evolution, deformation modes, and fracture mechanisms of zirconium plate produced using ultrasonic additive manufacturing (UAM) are presented. In addition to conventional tensile testing techniques, digital image correlation captured highly variable strain accumulation in specimens loaded perpendicular or parallel to the build height (Z). When tested in parallel to Z, delamination at prior foil/foil interfaces creates strain localization noticeable in strain rate maps, whereas specimens loaded perpendicular to Z illustrate conventional strain hardening until necking accelerates delamination. Although bond strengths are statistically and spatially variable, in situ electron backscattering diffraction tests illustrate the ability for grains near interfaces to accommodate strain with twinning and slip modes consistent with conventionally produced zirconium alloys. Finally, mixtures of ductile and delamination-induced fracture highlight the interface-driven failure modes of UAM zirconium plate in the as-built condition. Graphic abstract

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reduced synthesis temperatures of SrNbO 2 N perovskite films for photoelectrochemical fuel production

Perovskite oxynitrides, such as SrNbO 2 N, have been shown to be promising materials for photoanodes in tandem photoelectrochemical cells, due to their suitable bandgap and charge transport. However, thin film synthesis and characterization of oxynitride perovskites are challenging due to high processing temperatures that are incompatible with available substrates. In this work, we report on reduced synthesis temperatures of SrNbO 2 N perovskite thin films on Si substrates across a range of chemical compositions. Polycrystalline thin films with perovskite crystal structure are obtained by sputtering at ambient temperature and annealing at 550-600 degrees C. The perovskite structure has a relatively broad range of cation composition between 50 and 60% Sr with varying O/N ratio according to Rutherford backscattering spectrometry. The maximum photocurrent density was obtained at 55 cation % of Sr, which is slightly Sr-rich compared to the nominal SrNbO 2 N stoichiometry. This work shows the importance of considering cation and anion composition in studying oxynitride perovskites for solar fuel applications.

36 MATERIALS SCIENCE↗