Search NASA⌕ Search

SEARCH · Search NASA

Results for “depth profiles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Evolution of Microstructure and Surface Characteristics of FeCrAl alloys when Subjected to Flow Boiling Testing

FeCrAl alloys are candidate materials for manufacturing accident-tolerant fuel (ATF) cladding intended for light water reactors to increase fuel reliability and safety during design-basis and beyond-design-basis accident scenarios. The evolution of the materials' surface characteristics, microstructure, and mechanical properties when exposed to the Critical Heat Flux (CHF) in flow boiling testing is crucial for safety analysis while providing insights into their thermal-hydraulic performance in nuclear reactors. After CHF, the surface chemistry of two FeCrAl alloys, APMT and C26M, was studied to understand their evolution at the early stage of high-temperature excursions in short time periods. The results indicated a thin layer composed of oxides and hydroxides of Al, Cr, and Fe with varying proportions at different depths in the layer, as indicated by X-ray photoelectron spectroscopy (XPS) and depth profiling. The cross-sections prepared by focused ion beam (FIB) revealed the growth of an oxide layer, in the range of 90-180 nm thick, on the alloys' surfaces. The evolution of the materials' surface chemistry also led to a noticeable post CHF excursion increase in their wettability, with a slight increase in roughness. Further, the investigation of the materials' mechanical properties indicated a modest increase in hardness by 10-15% as well as an increase in their yield strength, as evidenced by the microindentation and ring compression tests conducted before and after CHF testing. Scanning electron Microscopy (SEM) and X-ray diffraction (XRD) were used to investigate microstructural features of the materials and their changes after CHF treatment.

36 MATERIALS SCIENCE↗

Hydrogen and deuterium permeation in Hastelloy N

Hastelloy N was chosen as the fluoride salt-contacting structural material for the Molten Salt Reactor Experiment due to its excellent compatibility with the fuel salt FLiBe. FLiBe is currently investigated for several advanced fusion and fission reactor concepts where tritium generation in the FLiBe is anticipated. Knowledge of hydrogen transport properties through Hastelloy N is important to understand how tritium would permeate through this material and result in an unintentional release. In this study, the hydrogen and deuterium permeability, diffusivity, and solubility were measured from 500 to 700 °C at a primary-side pressure of 10 kPa in a well-characterized sample of Hastelloy N. The prepared polycrystalline Hastelloy N had C and O impurities present on the surface. These impurities were investigated using Auger Emission Spectroscopy and Ar depth profiling. Here, the adventitious C was removed upon the first Ar sputter cycle whereas O persisted deeper into the sample. For permeation experiments, applied deuterium pressures ranged from 13 Pa to 100 kPa and deuterium transport remained in the diffusion-limited regime (J ∝ P 0.5 ) throughout the pressure range examined. Two methods are employed to measure the effective hydrogen and deuterium diffusivity: rise and decline. The decline method produced improved statistical model fits for calculating the effective diffusion coefficient compared to the rise method. The resultant transport properties compared well to published values for other nickel alloys.

08 HYDROGEN↗

Interface chemistry informs about cathode and anode degradation during fast charging

Here, the aim of this study is to examine the development and makeup of the Solid Electrolyte Interphase (SEI) and Cathode Electrolyte Interphase (CEI) in lithium-ion batteries during rapid charging. Using X-ray photoelectron spectroscopy (XPS) and depth profiling, we investigate the chemical modifications occurring on the electrode surfaces during the initial formation and subsequent fast charge-discharge cycles. Our research shows that the anode's SEI initially comprises a thin layer rich in ketones, which then transforms into a thicker layer dominated by carbonaceous compounds during rapid charging cycles. Following assembly, lithium fluoride (LiF) quickly becomes a key element of the SEI, and its presence continues to grow substantially during the formation cycle, remaining the primary component throughout subsequent cycles. Initially, the cathode forms a thin oxide layer rich in ketones, with no noticeable carbonaceous CEI. The CEI primarily comprises LiF, which experiences an increase during the formation cycle and retains a thin layer of carbon coating after the initial rapid discharge. These findings show how the interphase layers impact the performance and stability of lithium-ion batteries, especially during fast charging for electric vertical take-off and landing (eVTOL) vehicles.

Fast charging↗

The influence of A-site rare-earth for barium substitution on the chemical structure and ferroelectric properties of BZT thin films

Rare-earth (RE) doped Ba(Zr,Ti)O{sub 3} (BZT) thin films were prepared by rf-magnetron sputtering from a Ba{sub 0.90}Ln{sub 0.067}Zr{sub 0.09}Ti{sub 0.91}O{sub 3} (Ln=La, Nd) target. The films were deposited at a substrate temperature of 600 deg. C in a high oxygen pressure atmosphere. X-ray diffraction (XRD) patterns of RE-BZT films revealed a <001> epitaxial crystal growth on Nb-doped SrTiO{sub 3}, <001> and <011> growth on single-crystal Si, and a <111>-preferred orientation on Pt-coated Si substrates. Scanning electron microscopy (SEM) showed uniform growth of the films deposited, along with the presence of crystals of about half-micron size on the film's surface. Transmission electron microscopy (TEM) evidenced high crystalline films with thicknesses of about 100 nm for 30 min of sputtering. Electron-probe microanalysis (EPMA) corroborated the growth rate (3.0-3.5 nm/min) of films deposited on Pt-coated Si substrates. X-ray photoelectron spectroscopy (XPS), in depth profile mode, showed variations in photoelectron Ti 2p doublet positions at lower energies with spin-orbital distances characteristic of BaTiO{sub 3}-based compounds. The XPS analysis revealed that lanthanide ions positioned onto the A-site of the BZT-perovskite structure increasing the MO{sub 6}-octahedra distortion (M=Ti, Zr) and, thereby, modifying the Ti-O binding length. Polarization-electric field hysteresis loops on Ag/RE-doped BZT/Pt capacitor showed good ferroelectric behavior and higher remanent polarization values than corresponding non-doped system. - Graphical abstract: XPS narrow-scan spectra of Ti 2p doublets of the Nd-doped BZT films deposited on Pt-coated Si substrate.

36 MATERIALS SCIENCE↗

High-temperature crystal structure and transport properties of the layered cuprates Ln{sub 2}CuO{sub 4}, Ln=Pr, Nd and Sm

High-temperature crystal structure of the layered cuprates Ln{sub 2}CuO{sub 4}, Ln=Pr, Nd and Sm with tetragonal T'-structure was refined using X-ray powder diffraction data. Substantial anisotropy of the thermal expansion behavior was observed in their crystal structures with thermal expansion coefficients (TEC) along a- and c-axis changing from TEC(a)/TEC(c){approx}1.37 (Pr) to 0.89 (Nd) and 0.72 (Sm). Temperature dependence of the interatomic distances in Ln{sub 2}CuO{sub 4} shows significantly lower expansion rate of the chemical bond between Pr and oxygen atoms (O1) belonging to CuO{sub 2}-planes (TEC(Pr-O1)=11.7 ppm K{sup -1}) in comparison with other cuprates: TEC (Nd-O1)=15.2 ppm K{sup -1} and TEC (Sm-O1)=15.1 ppm K{sup -1}. High-temperature electrical conductivity of Pr{sub 2}CuO{sub 4} is the highest one in the whole studied temperature range (298-1173 K): 0.1-108 S/cm for Pr{sub 2}CuO{sub 4}, 0.07-23 S/cm for Nd{sub 2}CuO{sub 4} and 2x10{sup -4}-9 S/cm for Sm{sub 2}CuO{sub 4}. The trace diffusion coefficient (D{sub T}) of oxygen for Pr{sub 2}CuO{sub 4} determined by isotopic exchange depth profile (IEDP) technique using secondary ion mass spectrometry (SIMS) varies in the range 7.2x10{sup -13} cm{sup 2}/s (973 K) and 3.8x10{sup -10} cm{sup 2}/s (1173 K) which are in between those observed for the manganese and cobalt-based perovskites. -- Graphical abstract: Anomaly anisotropic thermal expansion behavior was observed for Pr{sub 2}CuO{sub 4} in comparison with Ln{sub 2}CuO{sub 4}, Ln=Pr and Nd having tetragonal T'-structure with thermal expansion coefficients (TEC) along a- and c-axis changing from TEC(a)/TEC(c){approx}1.37 (Pr) to 0.89 (Nd) and 0.72 (Sm). It was found that the trace diffusion coefficient (D{sub T}) of oxygen in Pr{sub 2}CuO{sub 4} determined by secondary ion mass spectrometry (SIMS) varies in the range 7.2x10{sup -13} cm{sup 2}/s (973 K) and 3.8x10{sup -10} cm{sup 2}/s (1173 K) which are in between those observed for the manganese and cobalt-based perovskites. Display Omitted Research highlights: {yields} Anisotropic high-temperature thermal expansion behavior of T'-Ln{sub 2}CuO{sub 4}, Ln=Pr, Nd and Sm. {yields} Anomalous expansion behavior of Pr{sub 2}CuO{sub 4} in comparison with Ln{sub 2}CuO{sub 4}, Ln=Nd and Sm. {yields} High-temperature electrical conductivity of Pr{sub 2}CuO{sub 4} is higher in comparison with other T'-Ln{sub 2}CuO{sub 4}. {yields} Values of the oxygen trace diffusion coefficient for Pr{sub 2}CuO{sub 4} are between those reported for the Mn- and Co-based perovskites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizations of silver alloys used in modern Mexican coins

This paper presents a complete methodology for the characterization of silver alloys used in modern coin production. Mexican coins with a nominal silver concentration from 10% to 99.99% were used in this study. Calibrated Glow Discharge Optical Emission Spectrometers were used to determine the chemical composition of the alloys as a function of the depth, while inductively coupled plasma was used to determine the total element composition in bulk. Scanning Electron Microscope was used to study the phase distributions in the different silver coins. According to Glow Discharge Optical Emission Spectrometers and inductively coupled plasma, the silver content found in the studied samples was consistently greater than that of the nominal silver content reported by the Mexican mint. This may lead to a review of the new methods of analysis used nowadays in contemporary coin minting. This result is very important because silver is increasing in value as metal and, considering the volume of production of silver coins, this may increase further as a consequence of a growing popular confidence in silver currency. In the case of silver studies, an advantage of the absence of silver detector in the Glow Discharge Optical Emission Spectrometers system is that it allows for the recalibration to have a better range of detection of other metals present in the alloys. A calibration curve using the copper content obtained by inductively coupled plasma (bulk) and Glow Discharge Optical Emission Spectrometers (depth profile) was performed. The relevance of control in modern silver coin minting was clarified, especially in minimizing the discrepancy between the nominal and the core fineness. The physical and chemical properties of the alloys studied are defined, revealing important variations in silver and copper contents. A new methodology and metrology for the control of coinage are suggested.

36 MATERIALS SCIENCE↗

Effect of cycled combustion ageing on a cordierite burner plate

A combination of {sup 57}Fe-Moessbauer spectroscopy and X-ray Powder Diffraction analysis has been employed to study modifications in chemical and mechanical stability occurring in a cordierite burner aged under combustion conditions which simulate the working of domestic boilers. Moessbauer study shows that Fe is distributed into the structural sites of the cordierite lattice as Fe{sup 2+} and Fe{sup 3+} ions located mostly at octahedral sites. Ferric oxide impurities, mainly hematite, are also present in the starting cordierite material accounting for {approx_equal}40% of the total iron phases. From Moessbauer and X-ray diffraction data it can be deduced that, under the combustion conditions used, new crystalline phases were formed, some of the substitutional Fe{sup 3+} ions existing in the cordierite lattice were reduced to Fe{sup 2+}, and ferric oxides underwent a sintering process which results in hematite with higher particle size. All these findings were detected in the burner zone located in the proximity of the flame and were related to possible chemical reactions which might explain the observed deterioration of the burner material. Research Highlights: {yields}Depth profile analyses used as a probe to understand changes in refractory structure. {yields}All changes take place in the uppermost surface of the burner, close to the flame. {yields}Reduction to Fe{sup 2+} of substitutional Fe{sup 3+} ions and partial cordierite decomposition. {yields}Heating-cooling cycling induces a sintering of the existing iron oxide particles. {yields}Chemical changes can explain the alterations observed in the material microstructure.

36 MATERIALS SCIENCE↗

Immediate impact on the rim zone of cement based materials due to chemical attack

Cement based materials are in their widespread application fields exposed to various aqueous environments. This can lead to serious chemical changes affecting the durability of the materials. In particular in the context of service life prediction a detailed knowledge of the reaction mechanisms is a necessary base for the evaluation of the aggressivity of an aqueous medium and this is deduced commonly from long term investigations. However, these processes start immediately at the material/water-interface, when a cementitious system comes into contact with an aqueous solution, altering here the chemical composition and microstructure. This rim zone represents the first hurdle that has to be overcome by an attacking aqueous solution. Therefore, the properties of the surface near area should be closely associated with the further course of deterioration processes by reactive transport. In this context short term exposure experiments with hardened cement paste over 4 and 48 h have been carried out with demineralized water, hard tap water and different sulfate solutions. In order to investigate immediate changes in the near-surface region, depth profile cuts have been performed on the cement paste samples by means of focused ion beam preparation techniques. A scanning beam of Gallium ions is applied to cut a sharp edge in the cement paste surface, providing insights into the composition and microstructure of the upper ten to hundred microns. Electron microscopic investigations on such a section of the rim zone, together with surface sensitive X-ray diffraction accompanied by a detailed characterization of the bulk composition confirm that the properties of the material/water interface are of relevance for the durability of cement based systems in contact with aqueous solutions. In this manner, focused ion beam investigations constitute auspicious tools to contribute to a more sophisticated understanding of the reaction mechanisms. - Highlights: • The chemical stability is related to the properties of material/water interface. • Properties of the rim zone readjust quickly, triggered by hydrochemical conditions. • Durability research can be improved by combining FIB techniques and common analytics.

36 MATERIALS SCIENCE↗

Analysis of position-dependent cavity parameters in irradiated metals to obtain insight on fundamental defect migration phenomena

Motion of point defects is a fundamental process that governs microstructure and properties of materials. Here, we examine the near-surface and grain boundary cavity swelling depth profiles in neutron- and ion-irradiated simple metals (Cu, Ni, and Fe-Cr) and investigate diffusional broadening of implanted Ni ions in Fe-Cr alloys. Vacancy migration energies and radiation-enhanced diffusion were experimentally estimated. Cavity denuded zone widths near planar sinks are shown to be dependent on temperature, damage rate, balance of point defects and sinks, and vacancy migration energies. An enhanced cavity swelling zone adjacent to the void-denuded zone was observed in specimens with low to moderate sink strength and interpreted as evidence of 1D gliding interstitial clusters. Radiation-enhanced diffusional broadening of implanted Ni ions (at 400–550 °C) in Fe and Fe-Cr was up to 250 nm toward the surface, which leads to a much broader near-peak-damage region where cavity swelling is suppressed. Diffusional broadening of implanted ions is calculated to be similarly pronounced for self-ion irradiations, particularly near the peak and higher swelling temperature regimes. Adequately high ion energies (~8–15 MeV) are recommended for ion-irradiation studies to provide a sufficiently broad midrange safe analysis region with minimized surface and injected ion effects.

36 MATERIALS SCIENCE↗

RBS, XRR and optical reflectivity measurements of Ti-TiO{sub 2} thin films deposited by magnetron sputtering

Highlights: Black-Right-Pointing-Pointer The single-, bi- and tri-layered films of Ti-TiO{sub 2} deposited onto Si(1 1 1) substrates. Black-Right-Pointing-Pointer Three methods RBS, XRR, optical reflectometer were used. Black-Right-Pointing-Pointer The real thickness of each layer was smaller than 50 nm. Black-Right-Pointing-Pointer Ti and TiO{sub 2} film-densities were slightly lower than the corresponding bulk values. -- Abstract: Single-, bi- and tri-layered films of Ti-TiO{sub 2} system were deposited by d.c. pulsed magnetron sputtering from metallic Ti target in an inert Ar or reactive Ar + O{sub 2} atmosphere. The nominal thickness of each layer was 50 nm. The chemical composition and its depth profile were determined by Rutherford backscattering spectroscopy (RBS). Crystallographic structure was analysed by means of X-ray diffraction (XRD) at glancing incidence. X-ray reflectometry (XRR) was used as a complementary method for the film thickness and density evaluation. Modelling of the optical reflectivity spectra of Ti-TiO{sub 2} thin films deposited onto Si(1 1 1) substrates provided an independent estimate of the layer thickness. The combined analysis of RBS, XRR and reflectivity spectra indicated the real thickness of each layer less than 50 nm with TiO{sub 2} film density slightly lower than the corresponding bulk value. Scanning Electron Microscopy (SEM) cross-sectional images revealed the columnar growth of TiO{sub 2} layers. Thickness estimated directly from SEM studies was found to be in a good agreement with the results of RBS, XRR and reflectivity spectra.

36 MATERIALS SCIENCE↗

AgSb(S{sub x}Se{sub 1−x}){sub 2} thin films for solar cell applications

Highlights: ► AgSb(S{sub x}Se{sub 1−x}){sub 2} thin films were formed by heating Na{sub 2}SeSO{sub 3} dipped Sb{sub 2}S{sub 3}/Ag layers. ► S/Se ratio was varied by changing the dipping time in Na{sub 2}SeSO{sub 3} solution. ► Characterized the films using XRD, XPS, SEM, Optical and electrical measurements. ► Band gap engineering of 1−1.1 eV for x = 0.51 and 0.52 respectively. ► PV Glass/FTO/CdS/AgSb(S{sub x}Se{sub 1−x}){sub 2}/C were prepared showing V{sub oc} = 410 mV, J{sub sc} = 5.7 mA/cm{sup 2}. - Abstract: Silver antimony sulfoselenide (AgSb(S{sub x}Se{sub 1−x}){sub 2}) thin films were prepared by heating glass/Sb{sub 2}S{sub 3}/Ag layers after selenization using sodium selenosulphate solution. First, Sb{sub 2}S{sub 3} thin films were deposited on glass substrates from a chemical bath containing SbCl{sub 3} and Na{sub 2}S{sub 2}O{sub 3}. Then Ag thin films were thermally evaporated onto glass/Sb{sub 2}S{sub 3}, followed by selenization by dipping in an acidic solution of Na{sub 2}SeSO{sub 3}. The duration of selenium dipping was varied as 30 min and 2 h. The heating condition was at 350 °C for 1 h in vacuum. Analysis of X-ray diffraction pattern of the thin films formed after heating showed the formation of AgSb(S{sub x}Se{sub 1−x}){sub 2}. Morphology and elemental analysis were done by scanning electron microscopy and energy dispersive X-ray detection. Depth profile of composition of the thin films was performed by X-ray Photoelectron Spectroscopy. The spectral study showed the presence of Ag, Sb, S, and Se, and the corresponding binding energy analysis confirmed the formation of AgSb(S{sub x}Se{sub 1−x}){sub 2}. Photovoltaic structures (PV) were prepared using AgSb(S{sub x}Se{sub 1−x}){sub 2} thin films as absorber and CdS thin films as window layers on FTO coated glass substrates. The PV structures were heated at 60–80 °C in air for 1 h to improve ohmic contact. Analysis of J–V characteristics of the PV structures showed V{sub oc} from 230 to 490 mV and J{sub sc} 0.28 to 5.70 mA/cm{sup 2}, under illumination of AM1.5 radiation using a solar simulator.

36 MATERIALS SCIENCE↗

Investigation of Cu(In,Ga)Se{sub 2} polycrystalline growth: Ga diffusion and surface morphology evolution

Graphical abstract: - Highlights: • Ga diffusion in CIGS absorption layer after annealing treatment. • Phenomenon of surface reconstruction after annealing treatment. • Understand selenium effect on CIGS annealing process. • Explain the kinetic of Ga diffusion and MoSe{sub 2} formation. - Abstract: We report a study of selenization and annealing treatment of copper indium gallium selenide (CIGS) film. Morphologies and composition of surface and cross section were observed by scanning electron microscopy (SEM) equipped with Energy Dispersive Spectroscopy (EDS). X-ray diffraction (XRD) and Raman spectra were used to investigate film structure. Depth profiles of element distributions were detected by Auger electron spectroscopy (AES). A double-layer structure was formed in the film by selenizing metallic precursor at 450 °C. Further annealing at 600 °C in pure argon enhanced gallium diffusion from the bottom to the top of the film, while additional selenium in the annealing had a negative effect. A MoSe{sub 2} layer was detected between CIGS and Mo layers with annealing in additional Se. The annealing treatment also significantly modified the film surface morphology. A large amount of triangular and polygon shaped islands were observed by SEM. That might be due to different nucleation kinetics for different crystal facets.

36 MATERIALS SCIENCE↗

Processing and structural properties of random oriented lead lanthanum zirconate titanate thin films

Highlights: • Pyrochlore phase crystallizes near the bottom film-electrode interface. • PLZT films show a non-uniform microstrain and crystallite size in depth profile. • Complex grainy structure leads to different elastic modulus at the nanoscale. - Abstract: Polycrystalline lead lanthanum zirconate titanate (PLZT) thin films have been prepared by a polymeric chemical route to understand the mechanisms of phase transformations and map the microstructure and elastic properties at the nanoscale in these films. X-ray diffraction, atomic force microscopy (AFM) and ultrasonic force microscopy (UFM) have been used as investigative tools. On one side, PLZT films with mixed-phase show that the pyrochlore phase crystallizes predominantly in the bottom film-electrode interface while a pure perovskite phase crystallizes in top film surface. On the contrary, pyrochlore-free PLZT films show a non-uniform microstrain and crystallite size along the film thickness with a heterogeneous complex grainy structure leading to different elastic properties at nanoscale.

36 MATERIALS SCIENCE↗

In situ X-ray Diffraction Study of Thin Film Ir/Si Solid State Reactions

The solid state reaction between a thin (30 nm) Ir film and different Si substrates (p-type Si(1 0 0), n- and p-type Si(1 1 1), silicon on insulator (SOI) and polycrystalline Si) was studied using a combination of in situ X-ray diffraction (XRD), in situ sheet resistance and laser light scattering measurements. No significant influence of either the dopants or the substrate orientation was detected as a phase formation sequence of IrSi, Ir{sub 3}Si{sub 4},Ir{sub 3}Si{sub 5} and IrSi{sub 3} was found for all samples. The presence of a thin (<4 nm) amorphous IrSi film at room temperature and its subsequent crystallization could be deduced from the appearance of a broad semi-amorphous diffraction peak in the XRD spectrum around 400 C. The results were verified using ex situ Rutherford Backscattering Spectroscopy, Scanning Electron Microscopy and 4-point probe measurements on quenched samples. The activation energy of the crystallization process and the silicide growth was determined using a Kissinger analysis on ramp anneals with different ramp rates. In addition, the influence of up to 25 volumetric % (20.5 atomic %) of Ir to the silicide formation in the Ni/Si system was studied on SOI and polycrystalline Si substrates. In the presence of Ir, the temperature range over which the low resistivity NiSi exists, is reduced both through an increase in formation temperature and an earlier consumption by the formation of NiSi{sub 2}. After the heat treatment, a continuous distribution of Ir throughout the NiSi{sub 2} phase was detected using X-ray photoelectron spectroscopy depth profiling. A low sheet resistance of < 20 {Omega}/{open_square} was maintained on both substrates up to 900 C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microscopic analysis of copper current collectors and mechanisms of fragmentation under compressive forces

Extensive fragmentation of copper current collectors was observed after spherical indentation on prismatic and large-format pouch Li-ion cells by 3D X-ray computed tomography (XCT). Microscopic analysis including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and x-ray photoelectron microscopy (XPS) was carried out on copper current collectors from used commercial cells and pristine anodes. The copper-graphite cross-section images showed rough interface areas affected by reactions and diffusion in the used cell. Electron probe micro-analyzer (EPMA) element mapping showed the interface area was rich in oxygen and phosphorus. A detectable amount of phosphorus was also uniformly distributed inside the current collector. The same oxygen and phosphorus distributions were confirmed by STEM/EDS analysis. XPS depth profiles on multiple elements revealed the interface area of the aged anode was rich in Li, F, P, O and C and diffused at least 50 nm into the copper. In comparison, the pristine anode showed a very smooth C/Cu interface. No other elements were detected. For commercial cells, the reactions in the interface area and diffusion of multiple elements into the lattice and grain boundaries were responsible for the embrittlement of the copper current collectors. Finally, permanent cell capacity loss was observed in electrochemical performance of the indented cells.

36 MATERIALS SCIENCE↗

Behavior and properties of helium cavities in ductile-phase-toughened tungsten irradiated with He + ions at an elevated temperature

Ductile-phase toughened tungsten (DPT W) composites have demonstrated a great potential for plasma-facing components in fusion power systems. These materials can retain the outstanding thermomechanical properties of W while significantly enhancing the fracture toughness. The DPT W composite in this study consists of W particles (88 wt.%) embedded in a ductile NiFeW (12 wt.%) solution matrix. Irradiation of the composite was performed with 90 keV He + ions to 1.0 × 10 17 He + /cm 2 at 973 K. The He cavities formed in both W and NiFeW phases are examined using convergent-beam scanning transmission electron microscopy (CB-STEM) at an atomic-level resolution. Full-range depth profiles of the He cavity diameters and number densities are analyzed. The results show that the average cavity diameter in NiFeW is ~2.7 times that in W, while the number density is an order of magnitude lower. A quantitative analysis of the He density and pressure in the cavities is also achieved using STEM electron energy loss spectroscopy (STEM-EELS) mapping. The He atoms in the cavities in NiFeW are found to be under-pressurized, while those in similar-sized cavities in W are not detectable. Further, the He energy-loss shift exhibits a linear relationship with the He density in cavities in NiFeW, with the slope comparable to that for martensitic steel.

36 MATERIALS SCIENCE↗

Exploration of Sn 70 Li 30 alloy as possible material for flowing liquid metal plasma facing components

As an advanced alternative to solid materials, Liquid Metals (LM) may offer more resilient and feasible Plasma Facing Components (PFCs). Particularly, regarding the unavoidable material erosion/degradation produced by particle/heat fluxes in future fusion devices where much longer duty cycles are expected. Furthermore, configurations that propose a flowing LM surface can add the advantage of a continuously fresh and clean layer facing the plasma. Although lithium is the most widely tested option, tin-lithium (SnLi) alloys have been proposed to attempt to combine the positive characteristics of both pure elements and ameliorate the specific issues of lithium. In this work, the potential use of Sn70Li30 alloy in such flowing concepts has been explored by addressing several preliminary and mandatory aspects for its utilization. Key issues such as wettability and compatibility of the alloy with relevant substrates have been studied in a multidisciplinary approach. The data obtained from deposited liquid tin-lithium droplets indicates approximate wetting temperatures of 360 °C, 390 °C and 405 °C for the fresh alloy on 316 stainless steel, molybdenum, and tungsten, respectively. However, the alloy contamination appeared to strongly affect the wetting characteristics of materials, increasing their wetting temperature by ~130 °C in the worst observed cases. Interestingly, in some instances, the instability of the liquid alloy surface was observed in the form of sudden gaseous ejection. The deposited droplets were posteriorly characterized in terms of absolute composition and depth profile by Inductively Coupled PlasmaOptical Emission Spectroscopy (ICP-OES) and Secondary Ion Mass Spectrometry (SIMS-ToF). Additionally, the nature and composition of the boundaries between the substrates and alloy microparticles was investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), and 3D Laser microscopy. The overall results of this post-mortem characterization revealed that first signs of corrosion induced by both alloy elements (lithium-chromium association and iron-tin intermetallic mixing) were present on 316 stainless steel after short exposures (≤3 h) at temperatures lower than 550 °C. Conversely, molybdenum and tungsten showed good compatibility with the alloy in equivalent conditions. The global implications of these results are finally addressed, focusing on the future perspectives and the more viable scenarios for the eventual utilization of these alloys in flowing liquid metal configurations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Impact of nanoparticle size and shape on selective surface segregation in polymer nanocomposites

A study of the impact of the size and shape of a nanoparticle on the evolution of structure and surface segregation in polymer nanocomposite thin films is presented. This is realized by monitoring the evolution of structure with thermal annealing and equilibrium depth profile of a deuterated polystyrene/ protonated polystyrene bilayer in the presence and absence of various nanoparticles. For the three shapes examined, sheet-like graphene, cylindrical carbon nanotubes, and spherical soft nanoparticles, the presence of the nanoparticles slowed the inter-diffusion of the polymers in the thin film. The larger nanoparticles slowed the polymer motion the most, while the smaller spherical nanoparticles also significantly inhibited polymer chain diffusion. At equilibrium, the soft spherical nanoparticles, which are highly branched, segregate to the air surface, resulting in a decrease in the excess deuterated PS at the surface. The graphene sheets and single walled carbon nanotubes, on the other hand, enhanced the dPS segregation to the air surface. The graphene sheets were found to segregate to the silicon surface, due to their higher surface energy. Interpretation of these results indicates that entropic factors drive the structural development in the nanocomposite thin films containing the spherical nanoparticles, while a balance of the surface energies of the various components (i.e. enthalpy) controls the thin film structure formation in the polymer-carbon nanoparticle nanocomposites.

nanocomposite↗