Search NASA⌕ Search

SEARCH · Search NASA

Results for “directional solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Internal temperature gradient of alloy semiconductor melts from interrupted growth experiments

Interrupted growth experiments on Hg(0.8)Cd(0.2)Se alloys were performed in an attempt to estimate the actual internal temperature gradient in the melt during directional solidification. The results have been analyzed in terms of a theoretical model which assumes an axial composition profile characteristic of diffusion controlled solute redistribution during growth. A comparison of the calculated and measured values suggests a reduction in the applied (empty furnace) temperature gradient by about a factor of three. Values of the interface segregation coefficient (k) determined from the phase diagram, predict values of solute concentration build up in the solid during growth interruptions which are inconsistent with measured results. It appears that the k values used tend to underestimate the actual k values for higher alloy compositions and overestimate k for the lower alloy compositions.

Andrews, R. N.↗

Spatial profile of thermoelectric effects during Peltier pulsing in Bi and Bi/MnBi eutectic

The spatial profile of the thermal transients that occur during and following the current pulsing associated with Peltier Interface Demarcation during directional solidification is studied. Results for pure Bi are presented in detail and compared with corresponding results for the Bi/MnBi eutectic. Significant thermal transients occur throughout the sample that can be accounted for by the Peltier effect, the Thomson effect, and Joule heating. These effects are separated and their behavior is studied as a function of time, current density, and position with respect to the solid/liquid interface.

Silberstein, R. P.↗

The effect of an electric field on the morphological stability of the crystal-melt interface of a binary alloy

A fully time-dependent linear stability analysis of the morphological stability of a planar interface during directional solidification of a binary alloy at constant velocity in the presence of an electric field, is performed. The electromigration of solute and the differing electrical conductivities of solid and liquid for a model in which the temperature gradient is constant are taken into account. The present results are compared with the constitutional supercooling criterion, and it is shown there may be substantial differences. A modified constitutional supercooling criterion which is valid over a large range of conditions is derived. It is also found under certain conditions that the onset of instability may be time dependent.

Wheeler, A. A.↗

Preparation for microgravity - The role of the Microgravity Material Science Laboratory

Experiments at the NASA Lewis Research Center's Microgravity Material Science Laboratory using physical and mathematical models to delineate the effects of gravity on processes of scientific and commercial interest are discussed. Where possible, transparent model systems are used to visually track convection, settling, crystal growth, phase separation, agglomeration, vapor transport, diffusive flow, and polymer reactions. Materials studied include metals, alloys, salts, glasses, ceramics, and polymers. Specific technologies discussed include the General Purpose furnace used in the study of metals and crystal growth, the isothermal dendrite growth apparatus, the electromagnetic levitator/instrumented drop tube, the high temperature directional solidification furnace, the ceramics and polymer laboratories and the center's computing facilities.

Johnston, J. Christopher↗

Process modelling for space station experiments

The work performed during the first year 1 Oct. 1987 to 30 Sept. 1988 involved analyses of crystal growth from the melt and from solution. The particular melt growth technique under investigation is directional solidification by the Bridgman-Stockbarger method. Two types of solution growth systems are also being studied. One involves growth from solution in a closed container, the other concerns growth of protein crystals by the hanging drop method. Following discussions with Dr. R. J. Naumann of the Low Gravity Science Division at MSFC it was decided to tackle the analysis of crystal growth from the melt earlier than originally proposed. Rapid progress was made in this area. Work is on schedule and full calculations were underway for some time. Progress was also made in the formulation of the two solution growth models.

Rosenberger, Franz↗

The influence of interfacial energies and gravitational levels on the directionally solidified structures in hypermonotectic alloys

Various Cu-Pb-Al alloys were directionally solidified under 1-g conditions and alternating high-g/low-g conditions (achieved using NSAS's KC-135 aircraft) as a means of studying the influence of interfacial energies and gravitational levels on the resulting microstructures. Directional solidification of low Al content alloys was found to result in samples with coarser more irregular microstructures than in alloys with high Al contents under all the gravity conditions considered. Structures are correlated with interfacial energies, growth rates, and gravitational levels.

Andrews, J. B.↗

Behavior of ceramic particles at the solid-liquid metal interface in metal matrix composites

Directional solidification results were obtained in order to investigate particle behavior at the solid-liquid interface in Al-2 pct Mg (cellular interface) and Al-6.1 pct Ni (eutectic interface) alloys. It is found that particles can be entrapped in the solid if adequate solidification rates and temperature gradients are used. Model results showed critical velocity values slightly higher than those obtained experimentally.

Stefanescu, D. M.↗

Heat of mixing and morphological stability

A mathematical model, which incorporates heat of mixing in the energy balance, has been developed to analyze the morphological stability of a planar solid-liquid interface during the directional solidification of a binary alloy. It is observed that the stability behavior is almost that predicted by the analysis of Mullins and Sekerka (1963) at low growth velocities, while deviations in the critical concentration of about 20-25 percent are observed under rapid solidification conditions for certain systems. The calculations indicate that a positive heat of mixing makes the planar interface more unstable, whereas a negative heat of mixing makes it more stable, in terms of the critical concentration.

Nandapurkar, P.↗

Multiple experiment processing furnace crystal growth facility (MEPF-CGF)

The Multiple Experiment Processing Furnace - Crystal Growth Facility (MEPF-CGF) will be an improved modular version of earlier generation directional solidification furnaces having the capability for processing larger samples, for on-orbit exchange of samples by a crew member, and for pre-mission reconfiguration to accommodate a variety of user requirements. The MEPF-CGF will provide the capability for crystal growth in the microgravity environment and will satisfy the processing requirements of the crystal growth community. The MEPF-CGF will be accommodated in the pressurized Spacelab Module (manned environment) on board the Space Shuttle Orbiter. The system will permit operation of the furnace with crew interaction and will utilize Spacelab/Shuttle resources such as experiment mounting provisions, electrical power, data, communication, heat rejection, and crew time.

Srinivas, R.↗

Programmable Multizone Furnace

Moving thermal gradients created without mechanical motion. Furnace having multiple, individually programmable heating zones developed for use in experiments on directional solidification. Holds rod specimen and generates thermal gradients moving along specimen. Elimination of translation mechanism makes furnace more compact and reduces vibrations, which disturb experiment. Availability of different temperature profiles through programming makes it versatile tool for research at low thermal gradients traveling at moderate speeds.

Ting, Edmund Y.↗

Identification of a cast iron alloy containing nonstrategic elements

A program was performed to address the mechanical and environmental needs of Stirling engine heater head and regenerator housing components, while reducing the dependence on strategic materials. An alloy was developed which contained no strategic elemental additions per se. The base is iron with additions of manganese, molybdenum, carbon, silicon, niobium, and ferro-chromium. Such an alloy should be producible on a large scale at very low cost. The resulting alloy, designated as NASAUT 4G-Al, contained 15 Mn, 15 Cr, 2 Mo, 1.5 C, 1.0 Si, 1.0 Nb (in weight percent) with a balance of Fe. This alloy was optimized for chemistry, based upon tensile strength, creep-rupture strength, fracture behavior, and fatigue resistance up to 800 C. Alloys were also tested for environmental compatibility. The microstructure and mechanic properties (including hardness) were assessed in the as-cast condition and following several heat treatments, including one designed to simulate a required braze cycle. The alloy was fabricated and characterized in the form of both equiaxed and columnar-grained castings. The columnar grains were produced by directional solidification, and the properties were characterized in both the longitudinal and transverse orientations. The NASAUT 4G-Al alloy was found to be good in cyclic-oxidation resistance and excellent in both hydrogen and hot-corrosion resistance, especially in comparison to the baseline XF-818 alloy. The mechanical properties of yield strength, stress-rupture life, high-cycle-fatigue resistance, and low-cycle-fatigue resistance were good to excellent in comparison to the current alloy for this application, HS-31 (X-40), with precise results depending in a complex manner on grain orientation and temperature. If required, the ductility could be improved by lowering the carbon content.

Cooper, C. V.↗

Side branch morphology and coarsening in directionally solidified Pb-8.4 at. pct Au

The scaling relationships among the morphological features associated with the formation of perturbations (side branches) in the intercellular regions of a directionally solidified Pg-8.4 at. pct Au alloy were investigated. It is shown that the ratio between the initial side-branch spacing near dendrite tips, lambda-2, and the dendrite-tip radius, r(t), equals 2 to 2.5. The ratio between the distance from the dendrite tip to the location of the first side branch formation, lambda(p), and the t(r) equals 8 to 10. It was found that the model proposed by Kirkwood (1985) for the secondary dendrite arm coarsening shows a very good quantitative fit to the experimentally observed secondary arm coarsening kinetics during directional solidification.

Tewari, S. N.↗

Analysis of the low gravity tolerance of Bridgman-Stockbarger crystal growth. I - Steady and impulse accelerations

The effects of steady and impulse-type residual accelerations on dopant distributions during directional solidification in 2D and 3D 'generic' models of the Bridgman-Stockbarger technique are investigated using numerical methods. The calculations are based on the thermophysical properties of molten germanium doped with a low concentration of gallium. A Chebyshev collocation pseudospectral method is used for the solution of the governing momentum-, mass-, species-, and heat-transfer equations. Only convection caused by temperature gradients is considered. It is found that lateral nonuniformity in composition is very sensitive to the orientation of the steady component of the residual gravity vector and to the particular operating conditions under consideration. It is also found that laterally or radially averaged composition profiles are alone insufficient to describe the extent of residual convection in a spacecraft environment. The effects of impulse-type disturbances can be severe and can extend for times on the order of 1000 sec after the termination of the impulse.

Alexander, J. Iwan D.↗

Fluid flow in solidifying monotectic alloys

Use of a two-wavelength holographic technique results in a simultaneous determination of temperature and composition profiles during directional solidification in a system with a miscibility gap. The relationships among fluid flow, phase separation, and mass transport during the solidification of the monotectic alloy are discussed. The primary sources of fluid motion in this system are buoyancy and thermocapillary forces. These forces act together when phase separation results in the formation of droplets (this occurs at the solid-liquid interface and in the bulk melt). In the absence of phase separation, buoyancy results from density gradients related to temperature and compositional gradients in the single-phase bulk melt. The effects of buoyancy are especially evident in association with water- or ethanol-rich volumes created at the solid-liquid growth interface.

Ecker, A.↗

Salt-finger convection under reduced gravity

Salt-finger convection in a double-diffusive system is a motion driven by the release of gravitational potential due to differential diffusion rates. Because of the fact that the destabilizing effect of the concentration gradient is amplified by the Lewis number (the ratio of thermal diffusivity to solute diffusivity) salt-finger convection can be generated at very much reduced gravity levels. This effect may be of importance in the directional solidification of binary alloys carried out in space. The transport of solute and heat by salt-finger convection at microgravity conditions is considered; instability arising from surface tension gradients, the Marangoni instability, is discussed, and the possible consequences of combined salt-finger and Marangoni instability are considered.

Chen, C. F.↗

Analysis of stability of a planar solid-liquid interface in a dilute binary alloy

This paper reconsiders the question of stability of a planar solid-liquid interface in an undercooled alloy melt without making the restrictive assumption of no heat flow in the solid (i.e., Gs = 0). The results of this analysis indicate that, provided the thermal gradient on the solid side of the interface, Gs, is positive, stability can be achieved in an undercooled alloy melt for growth rates R greater than Ra (where Ra is the absolute stability limit of Mullins and Sekerka, 1964). Thus, the absolute stability criterion for steady-state planar growth in an undercooled alloy melt is the same as derived earlier by Mullins and Sekerka for directional solidification. Relaxing the restrictive assumption of Gs = 0 also reveals that there is a regime of stability for low growth rates and low supercoolings.

Laxmanan, V.↗

Stability of dendritic arrays

An approximate method for studying steady-state properties and linear stability of the dendritic arrays that are formed in directional solidification of alloys is proposed. This analysis is valid at high growth rates where the primary spacing between dendrites is larger than the velocity-dependent solutal diffusion length. A neutral stability boundary is computed and it is found that, in the situations where the results should be valid, the experimental data of Somboonsuk, et al. (1984) lie in the stable region, well away from the boundary.

Warren, James A.↗

Effect of thermosolutal convection on the solid-liquid interface in Pb-Au alloy

Liquid-solid interface distortion in the region of primary dendrite tips has been investigated in directionally solidified Pb-8 wt pct Au alloy. The distortions are caused by thermosolutal convection despite choice of growth conditions which should have been thermally and solutally stabilizing. The convection produces clustering of primary dendrites on a plane perpendicular to the growth direction. It produces a mushy zone, where the primary dendrites do not protrude with a uniform length, across the specimen cross section, resulting in large macrosegregation in the transverse direction. However, little macrosegregation is observed along the growth direction. The mushy zone, with uneven dendrite lengths, forms in the beginning of directional solidification. Its shape and dendrite distribution do not show much change during subsequent solidification. Tip morphologies of primary dendrites, within the dendrite clusters, appear to follow the morphological stability relationship.

Tewari, S. N.↗